Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.0 CrAccepted-Finance | ₹2.0 Cr | L1 | Accepted-Finance Accepted |
| 2 | L2₹2.1 CrAccepted-Finance | ₹2.1 Cr | L2 | Accepted-Finance Accepted |
| 3 | L3₹2.1 CrAccepted-Finance | ₹2.1 Cr | L3 | Accepted-Finance Accepted |
| 4 | L4₹2.5 CrAccepted-Finance | ₹2.5 Cr | L4 | Accepted-Finance Accepted |
Tender Value
₹2.8 Cr
EMD Value
₹5.7 L
Closing Date
24 Jan 2026, 3:00 pmClosed
Executive Engineer, CD-XII. I and FC Deptt.
Executive Engineer, CD-XII. I and FC Deptt.
Construction and Repair of Boundary wall at Right Bank of Kushak Drain and Ramps on both Banks from INA metro station to Kushak bus depot (Upstream).
2026_IFC_285103_1
EE/CD-XII/2025-26/109
Open Tender
Civil Works
180 days
INA Metro Station
Please refer Tender Documents
8 documents required · 8 mandatory
₹0
₹5.7 L
27 Jan 2026
17 Jan 2026
24 Jan 2026
17 Jan 2026
24 Jan 2026
17 Jan 2026
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
Masonry work with C&D recycled cement concrete brick of size 230mm x110mm x75mm of grade M-10 in foundation and plinth in cement motar 1:6( 1 cement : 6 coarse sand).
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor II level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand). (9105.95- 1183.18)=7922.75
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor II level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (11505.50-942.35)=
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work
Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately).
Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :15 mm wide and 15 mm deep groove
15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)
Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
Providing and laying RMC of M-30 grade By using minimum 400kg of cement(43 grade, OPC) per cum of concrete in roads / streets manufactured in automatic RMC plant using coarse sand and graded stone aggregate of 20mm nominal size in appropriate proportion as per approved design criteria including transportation to site in transit mixer, including cost of admixture in recommended proportion as per IS9103 to accelerate/ retard setting of concrete to improve workability with out impairing strength and durability as per specification including spreading and compacting mechanically by using needle and surface vibratos, leveling to required slope & camber, finishing by floating & brooming with wire brushes etc. and curing including making provision for contraction / expansion, construction of cross / longitudinal joints of size 10mm wide 50mm deep by groove cutting machine, providing and filling joints with approved joint filler and sealants, etc. complete, as per direction of Engineer in-charge. (Cost of joint filler & sealants shall be paid for separately under relevant items). Note:- Cement content considered in M-30 is @ 400 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately M-30 RMC by using minimum cement @400 kg/cum. Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer.
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by engineer-in-charge.
Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.
Providing thematic painting on outer face of existing boundary wall depicting theme of nature / culture by using exterior weather proof emulsion paint including design charges etc. complete.
Providing and laying rubble / stone soling which include the moorum for making the hard bearing strata.
Supply and installation of a 32-channel NVR supporting a minimum of 5MP resolution with H.265/H.264 compression, ONVIF compliance, dual SATA support, and remote monitoring capability. It also requires 4MP outdoor IP cameras with built-in microphones, IR night vision of at least 30 meters, PoE support, and an IP66 weatherproof rating. A 10TB WD surveillance-grade hard disk is to be provided, suitable for 24×7 continuous recording. The networking components include an 8-port PoE switch (D-Link or equivalent) with IEEE 802.3af/at support, at least 120W PoE power budget, and surge protection; high-quality Cat-6 UTP cable of 23AWG copper; PoE manage box with metal enclosure and lock; and weatherproof IP65 junction boxes. Accessories such as a 1.5-meter HDMI cable (HDMI 2.0), CAT6-compliant RJ45 connectors, and a 4U wall-mount rack with proper ventilation and lockable door are included. A minimum 32-inch Full HD LED TV with HDMI input must be supplied for monitoring purposes. Optical fiber single-mode 9/125 μm armored cable is required along with compatible gigabit media converters supporting single-mode fiber up to at least 20 km. Electrical components include ISI-marked 1.5mm copper AC wire and complete electrical installation work including routing, fixtures, and conduit as required. The tender also covers installation charges for cameras, NVR, cabling, testing, commissioning, and necessary accessories, as well as setting up internet connectivity for remote access and configuring a landline connection wherever needed complete as per direction of Engineer in Charge.
Providing and fixing container office size 20x10x8.6 feet with office cabin, room cabin, pentry and toilet attach bath, Specification Bottom Frame : 125mmx75mm c-channel, Stiffener bottom : 75mmx75mm Ms square Hollow Section pipe, Top Frame : 60mmx60mm Ms square Hollow Section pipe, Paneling Outside : 1.2 mm Ms corrugated Sheet 18 guage, Internalwall Paneling : 6 mm pre laminate MDF Ply, Roof Outside : 1.2 mm Ms Corrugated Sheet 16 Guage, Flooring system : 18 mm Wooden Ply with 1.3mm Pvc Carpet, Out sidepaint :New Painting With Enamel paint, Glasswool :50mm Insulation Of Glass Wool, Split Ac provision : As per your Requirment, Hooks :04 no. Lifting hooks, Windows : Aluminium sliding Window ‘2x2.5’with safety grill nd Shed, Legs :04 no . legs, FAN -2, TUBELIGHT -4, 6AMP SOCKET-5, 6 AMPSWITCH -14, 16 AMPSOCKET&, SWITCH-1, MAIN DOOR “(3X7”) , WINDOW(2.5X2.5) -2, BULKHEAD -1, Winodow AC PROVISION -1 (LETBATH ATTACHED (5x5)+DOOR +WC SHEET+WASHBASIN+SHOWER+TAB )-1, EXHAUST FAN-2 , LED LIGHT-2, (OPEN PANTRY(5X5)+SINK +SLB+CABINET )-1 , BOSS CABIN (9X10)+DOOR
Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 cm to 90 cm ht. plant in 25 cm size Earthen Pot/ Plastic Pot.
Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.
Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.
Supply and stacking of plant Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag
Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs,herbs, edge, flower beds, foliages & creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required), top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by officer-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide, lawn mover and brush cutter with fuel & other T & P material/plants shall be provided by the department.)Open Spaces. (3.00 Acres=One Mali) As per yard stick.
Supply of Earth Including royality,excavation,Loading & unloading and carriag by mechnical transport lad upto 5 K.M banking excavatd earth in laying not exceeding 20 cm in depth,breaking clods,rolling each layer with 1/2 tonne rollr or wooden or stel rammers,and dressing up in mbankments for roads flood banks,marginal banks and guide banks or filling up ground depressions and lift upto 1.5 m in all kind of soil.
Supply, Installation, Testing and Commissioning of off grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a)Solar Photovoltaic Module of capacity 330 Wpor above, manufacture din India, conforming to I S14286 / IEC61215 ,IS/ IEC 61730-Part-1,IS/IEC61730-Part-2.Solar Photovoltaic Module conversion efficiency shall not be less than 16.5% .PV module susedin solar power plants /systems must be warranted for their output peak watt capacity, which should not be less than 90% attheend of1 0year sand 80% attheend of 25 years. b)Power Conditioning Unit (PCU) of 350-800 VDC Input voltag erange and 400VAC, three phase, 4wire, 50Hz+/-2.5Hz, output voltag esuitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Inverter‑Charger (Off‑Grid PCU): Conform to relevant IEC/IS standards for grid‑interactive and standalone inverters and manufacturer type‑tests as required by MNRE empanelment; inverter/charger must meet MPPT, efficiency and protection criteria referenced by MNRE/agency specs make UTL SOLAR/Tata/Luminous/EAPRO . d)Battery Systems and BMS: Follow manufacturer/industry standards for battery design, testing and safety; for installations, use BMS with protection, thermal monitoring and communication per ANERT/MNRE recommendations and local electrical codes make UTL SOLAR/Tata/ Luminous/ EAPRO. e)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and out going cable along with glands, lugs and other accessories etc. as required. f) Lightning and surge voltage protection. g)Connections & Inter connections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grad armored power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel / conduit lugs and other accessories etc.as required.
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 18.89 MB
NIT109.pdf
Tender Documents • 18.87 MB
BOQ_377148.xls
BOQ • 0.31 MB
Download all tender documents and submit your bid