Renovation and Interior Work for the Department of Empowerment of Persons with Disabilities (DEPwD)

Amount

A-CIVIL WORK Dismantling, Demolishing & Repair Work Dismantling wood work of area below 40 sq.cm. wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. Lead

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead : Of area 3 sq.m. and below

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 mts. lead.

Removing white or colour wash by scrapping, sand papering and preparing surface smooth including necessary repairs to scratches etc. complete.

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling of existing sanitory wares, and all plumbing fittings including disposal of unserviceable material and stacking of serviceable materials. Wall mounted wash basin - 2 Nos European type W.C. Pan - 2 Nos Hand Shower (Health Faucet) - 2 Nos Short Body Bib cock - 2 Nos Long Body Bib Cock - 2 Nos Pilar Tap - 2 Nos

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Dismantling cement asbestos celotex or other ceiling or partition hard broad wall including stacking of serviceable materials and disposal of unserviceable materials within 50 mts. lead.

Crack filler for plasters, IPS, cement sand screeds and non – structural cracks. Do Not open the cracks, Clean the cracks so as to free them from oil, dust, loose particles etc. Moisten the surface with water, Fill cracks with EPCO – ACR using spatula or a putty knife. While applying avoid formation of cavity or bubbles. After filling , allow the surface to dry for at least 24 hours. Apply in layers at 24 hours interval. If the depth of the crack is more than 10mm. incl. cost of scaffolding transport etc. as per dir of EIC. All the chemicals will be of Krishna Conchem Products Pvt. Ltd. or Equivalent

Masonary / Brick Work Brick work using fly ash bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with bricks of class designation 40 kgs / cm2. in superstructure upto floor five level. : 230 x 110 x 80 mm

Centering & shuttering Works Centering & shuttering including strutting, propping etc. & removal of forms for Sides & Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers & Lintels plinth beams not exceeding 1m in depth at all levels

Steel, Structural and Aluminium Work Providing TMT steel reinforcement bars of SAIL, TATA. VIZAG make only (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint. In R.S. joists, channels, angles, tees

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with two sliding shutters using 18 mm series shutters section including powder coating with pure polyester powder of shade of required colour on the aluminium section. b) Plain glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Adjustable louvered windows including powder coating with pure polyester powder of shade of required colour on the aluminium section :Figured glass

Providing and fixing anodized aluminium partitions in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Fixed partitions including powder coating with pure polyester powder of shade of required colour on the aluminium section a. 9mm thick Eco Board

Providing and fixing anodized aluminium partitions in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Fixed partitions including powder coating with pure polyester powder of shade of required colour on the aluminium section b. 8mm thick Toughen Glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Single or double leaf door shutters. a. 9mm thick Eco Board

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Single or double leaf door shutters. b. 8mm thick Toughen Glass

Providing and fixing with aluminium framework of size 50mm x 25 mmx 1.0 mm tubular frame covering the partition roof with 12mm laminated panel as per the direction of Engineer-in-Charge.

Providing & fixing MS grill of required pattern in wooden frames of windows, masonry etc with MS flats, square or round bars with round headed bolts & nuts or by screws : Plain Grill

Reinforcement Cement Concrete Providing & laying in position machine batched concrete (BMC), machine mixed & machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering, shuttering, finishing & reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing the strength & durability as per the direction of the Engineer-incharge. All works upto floor V level. Add for providing richer or leaner mixes respectively at all floor levels. Providing M-30 grade concrete by using 420kgs of cement per cu.m. of concrete instead of M-25 grade of B.M.C.

Roofing Works Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Door & Joinery Works Providing flat iron hold fast 40 cms including fixing to frame with 10mm dia bolts, nuts & wooden plugs & embedded in cement concrete block 30x10x15 cms 1:3:6 mix (1 Cement : 3 Coarse Sand : 6 Stone aggregates 20mm nominal size) : 40 x 3 mm flat iron hold fast 15cm long

Providing & fixing wood work in frames of doors, windows, clerestory windows, trusses & other frames wrought framed & fixed in position : Second class Indian teak wood

Plastering and Painting Works Melamine polishing on wood work (one or more coat) : Glossy

12mm cement plaster 1:4 (1 cement : 4 fine sand)

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Wall painting (one or more coats) with plastic emulsion paint of approved brand and manufacture on old work to give an even shade.

Flooring Skirting and Dadoing Providing and fixing Vinyl flooring of approved shade and design with adhesive complete.

Providing and laying engineered wooden floor skirting of height 75mm of approved make (armstrong/ ego ) laid with adhesive & also includes leveling with plaster of paris if requiered & as per instruction of engineer in charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm : Jet Black

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. Dark & Light Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. : Wall Ceramic Glazed Tiles : 300 x 450

Precast plain Cement Tacktiles 32mm thk of required shade in floors, treads of steps and landing laid on 25mm bed of cement mortar 1:4(1cement:4coarse sand) jointed with neat cement slurry with pigment to match the shade of tiles including rubbing and polishing complete.

B-PLUMBING / SANITARY WORK Supply and fixing of under counter type of approved make Stainless steel kitchen sink without drain board of Overall size 610mmx460mm (24"x18") bowl size 560mmx410mmx215mm (22"x16"x81/2") Glossy. 1.0mm thk , 15mm nominal bore Fancy LONG BODY BIB Cock WITH WALL FLANGE Jaguar make or equivalent, C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including with approved mirror polish granite top in single piece & for sides in single piece over average 40 mm thick cuddappa supporting top slab, 25 mm nosing and rounding of granite top and sides, inclusive of sandwitched partitions of 25 mm thick cuddappa slabs using cement slurry or equivalent, cut out of required sizes to receive fittings an pipes , chasing in walls and making grooves etc complete ( Rate quoted per unit of Kitchen sink comple in all respects)

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. a) Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitereous china pedestal type (Europen type) water closet with seat as lid, whth C.I. brass hinges and rubber fitings 15 lts white vitreous china low level flushing cistern with fittings as brackets 40 mm white precelain 3enameled flush bad, 25 mm overflow pipe with specials and mosquito proof coupling of approved municipal design complete, including cutting and making good the walls and floors where required. : W.C. pan with white plastic seat and lid

Providing and fixing brass stop cock (heavy) of approved quality : 15 mm nominal bore

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed. a. 110 mm dia

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed. b. 75 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. a. 110 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 75 mm dia

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. a. 15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. b. 20 mm dia nominal outer dia pipes.

Providing and fixing NICKEL chrome plated copper alloy Fancy two way long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with sheet flance 20mm Jaquar make or equivalent. Confirming to IS 8931;1993 20mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy Bib Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore

C-INTERIOR Providing and fixing 15mm thick densified tengular edged eco friendly light weight Calcium Silicate false ceiling tiles (like Aerolite Brand or Equivalent) of approved texture Spintone/ Cosmos/ Fine Fissured or equivalent of size 595mm x 595mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per square metre. including both side) consisting of main "T" runner suitably spaced at joints to get required length and of size 24x38mm made from 0.33mm thick (minium) sheet, spaced 1200mm center to center, and cross "T" of size 24x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x600mm panel to from grid of size on a Perimeter wall angle precoated steel of size 600x600mm, resting on periphery walls/ partitions (24x24x300mm) made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm and laying 15mm thick densified edges calcium silicate ceiling tiles of approved texture light fittings, fixture, smoke detectors etc., wherever required. Main "T" runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm fixed to celing using with 12.5mm dia and 50mm long dash fastners, level clips of size 85x30x0.8mm, spaced at 1200mm center to center along main "T" bottom exposed with 24mm of T-section shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings etc. complete. (As Directed by Engineer in Charge) Note: Only Calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having are less than 0.30 sqm. The Calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection>85% non-combustible as per B.S.476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/m 0 KC.

ROLLER BLINDS Providing & fixing in position roller blinds of approved make, color, shade of varying length, approved fabric with aluminum extruded rail powder coated in white. Control unit to be made of high strength reinforced plastic. Roller tube to be anodised extruded tube of high strength alloy, including all necessary fittings and fixtures like idler, head rail, control unit, roller tube, bottom rail, operating chain, fixing brackets, clamps, etc. complete. All the materials shall be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer.

PIN -UP BOARDS (SOFT BOARDS) Supply and installing in position soft display board having aluminum frame including 12mm thick soft board with blazer cloth top fixed in frame with clip fitting with all stainless steel hardwares and easy fixing to the wall. All material shall be of approved make. All works complete as per the drawing / Image, specification and direction of the Engineer. : SIZE - 1000mm (L) X 350mm (HT)

MAGNETIC WHITE MARKER BOARD (SIZE : 2400mm(L) x 1200mm(HT) Providing and fixing in position approved Magnetic white matt finish marker board of (SIZE - 2400 X 1200 ) having Moulded Anodized Aluminium frame & stain resistant porcelain coated 28 gauge steel backing with Virgin ABS (Acryloniprile Butadiene Styrene) Molded 300x100mmm Chalk tray and Eraser complete, including all accessories. All material shall be of approved make. All works complete as per the drawing./ Image, specification and direction of the Engineer.

NOTICE BOARD (SIZE: 1200mm (L) x 900mm (HT) Providing and fixing in position Notice board of size 1200mm(L) X 900(HT) mm made of Aluminium frame with Acrylic shutter including 12mm thick soft board with blazer cloth top fixed in frame with clip fitting with all stainless steel hardwares such as screws, locking arrangement etc. and making arrangement for fixing on wall all complete as per design. All material shall be of approved make. All works complete as per the drawing./ Image, specification and direction of the Engineer.

SOLID PARTITION FINISHED WITH LAMINATE Providing & fixing in position full height solid partition made out of aluminium framework of size 65mm x 38 mm tubular frame ,18 gauge having grid spacing at 600mm x600mm center to center both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. Provision shall be made for wire management to take care of basic wiring requirement for providing power data- voice switches on a modular switch plate. All material will be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

SINGLE SHUTTER DOOR IN PARTITION (SIZE - 1000 mm (L) X 2100 mm (HT) Providing & fixing in position frameless factory made solid core water proof flush door shutter of size 1000mm x 2100mm x 35 mm thick & finished with 1mm thick laminate of approved colour & texture on both sides & teak wood lipping of size 37x12mm on edges of shutter. The door shall be fixed on SS. brush finished brass butt hinges & provided with a surface mounted hydraulic door closer, SS matt finish concealed mortise lock case with lever handle, profile thumb turn cylinder (with key outside & thumb turn inside) with key hole, PVC door buffer & SS brush finish door stopper. All exposed teak wood lipping shall be finished with 3 coats or more of melamine polish (Matt/Gloss) to match the colour/ shade of the laminate including final coat of buffing till the required finish is achieved. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

SINGLE SHUTTER DOOR FOR BARRIER FREE TOILET (SIZE - 1000 mm (L) X 2100 mm (HT) Providing and fixing flush door shutter for barrier-free toilet, confirming to IS:2202 (Part I), of solid core type, 35 mm thick (or as specified), finished with both-side laminate/veneer/paint as per architectural drawing. Door to be mounted in powder-coated aluminum or hardwood frame, fitted with stainless steel 180-degree openable double-action hinges, allowing bi-directional swing (inward and outward). Door to have minimum clear opening width of 900 mm, fitted with D-type or lever-type handles, privacy lock with emergency release mechanism, kick plate at bottom (SS), and suitable hold-open/stay arrangement. Door to be mounted flush with the floor level, with no threshold or beveled threshold, ensuring full wheelchair accessibility. All fittings shall be corrosion-resistant and suited for wet areas. Note: Rate to include all materials, labour, hardware, fasteners, and installation complete in all respects.

GLASS DOOR (SIZE - 1400 mm (L) X 2100 mm (HT)) Glass door shall be made using 12 mm thick toughened glass with 100 mm high plywood frame with laminate finish, fixed using double action floor spring, top patch, bottom pivot in SS brush finish and s.s. 304 grade handles of size 200mm. Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

FROSTED FILM FOR CABIN GLASSES Providing and fixing frosted Glass film partly opaque and partly translucent on glass internal partitions and doors as per approved sample, design, drawing, & direction of the Engineer with necessary adhesive materials; etc complete.

SINGLE SHUTTER DOOR WITH VISION PANEL (SIZE - 1000 mm (L) X 2100 mm (HT)) Providing & fixing in position factory made solid core waterproof flush door shutter of 35 mm thick & finished with 1mm thick laminate of approved colour & texture on both sides & teak wood lipping of size 37x12mm on edges of shutter. The shutter shall be provided with a vision panel of size 275x600mm using glass of 8 mm thickness fixed with teak wood beading of size 19x12mm on both sides. The door shall be fixed on SS. brush finished brass butt hinges & provided with a surface mounted hydraulic door closer, SS matt finish concealed mortise lock case with lever handle, profile thumb turn cylinder (with key outside & thumb turn inside) with key hole, PVC door buffer & SS brush finish door stopper. All exposed teak wood lipping shall be finished with 3 coats or more of melamine polish (Matt/Gloss) to match the colour/ shade of the laminate including final coat of buffing till the required finish is achieved. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

PARTLY GLASS PANELLED & PARTLY SOLID PARTITION WITH LAMINATE FINISH Providing & fixing in position, full height partly glass panelled & partly solid partition made of treated salwood framework of size 38mm x 50mm having grid spacing at 600mmx600mm centre to centre both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. The partition will have an opening as per the height specified in the drawing. Glass of thickness 12 mm will be fixed in the opening with wooden beading of size 38mm x 12 mm on both sides. Wooden beadings will be finished in three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved . All hidden framework to be painted with black japan paint.

Wall panelling for video wall & false column work: Providing & Fixing 19 mm Boiling Water Proof (BWP) ply on the wall in a singular plane over a length of 7290mm and a width of 1390mm in the centre of the wall so to provide provision for mounting the TV Units for Video Wall. A wall panel of depth 160 mm using 19 mm thick BWP ply with suitable supports in between the wall and the ply sheets for the remaining portion of the wall and 2 False columns of size 840 mm X 685 mm attached at both the corners of the wall for the purpose of storage. The panelled area should have 1 mm thick laminate of approved shade and the Doors of the false coulumns shall have louvers of approved shade. All the material shall be of approved make i.e Ply wood- Kenwood Boiling Water Proof (BWP) Marine ply and Laminate- Greenlam.

STAINLESS STEEL DUST BIN (250mm dia x 400mm ht ) Providing and placing in position 16 gauge pedal stainless steel dust bin of grade 304 cylindrical with cover (250mm dia x 400mm ht). All material shall be of approved make. All complete as per the drawing, specification and direction of the Engineer.

MIRROR (Size- 900mm(L) x1200mm(HT) Providing & fixing in position 6mm thickness Mirror on wall using 304 grade S.S studs with crystal polished edges with required accessories. The mirror shall have holes of suitable diameter for fixing SS. studs, with necessary hardware, labour, fixing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

ARTIFICIAL GREEN PLANT WITH PVC POT Supplying and fixing in position approved artificial Green Plant with PVC pot (Pot size around 400mm dia x 600mm height ). All the materials shall be of approved make. All works complete as per the drawing, specification, image and direction of the Engineer.

Providing and fixing of main Signage board of specified design and colour made of 15 mm thick letterings made of acrylic and pasted with special glue/tape to the existing glass.

Providing and fixing acrylic signage board made from high-quality cast acrylic sheet of approved brand and color, thickness 3mm to 5mm (as specified), precision laser-cut to required shapes and letters/numbers/logos, with smooth polished edges. The signage shall be either front-lit, backlit, or non-illuminated as per design and location. The acrylic board shall be mounted on a backing sheet (if specified) or fixed directly to the wall surface using approved stainless steel standoffs/spacers or concealed adhesive system, as instructed by the Engineer-in-Charge. The rate shall include all necessary materials, labor, cutting, polishing, fixing accessories, hardware, adhesives, scaffolding (if required), transportation, and incidentals to complete the work in all respects. Note: Shop drawings and samples to be submitted for approval prior to fabrication. a. Size 30x5 cms (Cabins)

Providing and fixing acrylic signage board made from high-quality cast acrylic sheet of approved brand and color, thickness 3mm to 5mm (as specified), precision laser-cut to required shapes and letters/numbers/logos, with smooth polished edges. The signage shall be either front-lit, backlit, or non-illuminated as per design and location. The acrylic board shall be mounted on a backing sheet (if specified) or fixed directly to the wall surface using approved stainless steel standoffs/spacers or concealed adhesive system, as instructed by the Engineer-in-Charge. The rate shall include all necessary materials, labor, cutting, polishing, fixing accessories, hardware, adhesives, scaffolding (if required), transportation, and incidentals to complete the work in all respects. Note: Shop drawings and samples to be submitted for approval prior to fabrication. b. Size 30x10 cms (Common Areas)

Providing and fixing acrylic signage board made from high-quality cast acrylic sheet of approved brand and color, thickness 3mm to 5mm (as specified), precision laser-cut to required shapes and letters/numbers/logos, with smooth polished edges. The signage shall be either front-lit, backlit, or non-illuminated as per design and location. The acrylic board shall be mounted on a backing sheet (if specified) or fixed directly to the wall surface using approved stainless steel standoffs/spacers or concealed adhesive system, as instructed by the Engineer-in-Charge. The rate shall include all necessary materials, labor, cutting, polishing, fixing accessories, hardware, adhesives, scaffolding (if required), transportation, and incidentals to complete the work in all respects. Note: Shop drawings and samples to be submitted for approval prior to fabrication. c. Size 15x20 cms (Directions)

Providing and fixing acrylic signage board made from high-quality cast acrylic sheet of approved brand and color, thickness 3mm to 5mm (as specified), precision laser-cut to required shapes and letters/numbers/logos, with smooth polished edges. The signage shall be either front-lit, backlit, or non-illuminated as per design and location. The acrylic board shall be mounted on a backing sheet (if specified) or fixed directly to the wall surface using approved stainless steel standoffs/spacers or concealed adhesive system, as instructed by the Engineer-in-Charge. The rate shall include all necessary materials, labor, cutting, polishing, fixing accessories, hardware, adhesives, scaffolding (if required), transportation, and incidentals to complete the work in all respects. Note: Shop drawings and samples to be submitted for approval prior to fabrication. d. Size 3x10 cms (Push /Pull)

D-FURNITURE Supplying and placing in position Executive Table with Return Unit which is high gloss PU- finish panels, with toughened streak glass modesty for the main desk. It is equipped with a push-to-open mechanism for the drawer. All material shall be Godrej/ Durian/ feather lite make and colour. Size not less than for desk L=210cm W=90cm H=75cm and for side unit W=100cm, D=45cm and H= 700cm. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 1 from Volume IV

Supplying and placing in position Executive Table with Return Unit. The desk to be of Veneer finish with leather padding across its width to reduce wear and tear. The side unit to be placed on either side of the user. All material shall be of Godrej/ Durian/ feather lite make and colour. Size not less than for desk L=180cm W=90cm H=75cm and for side unit W=51cm, D=44.3cm and H= 63.5cm. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 2 from Volume IV

Supplying and placing in position Executive Desk with side unit with an inbuilt pull-out keyboard tray. All material shall be of Godrej/ Durian/ feather lite make and colour. Size not less than for desk W=165cm, D=70cm and H= 74.3cm and for side unit W=100cm, D=45cm and H= 74.3cm. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 3 from Volume IV

Supplying & placing in position wooden Desk with customised variable drawer. The drawers are lockable. All material shall be of Godrej/ Durian/ feather lite make and colour. Size L=120cm W=60cm H=74.3cm. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 4 from Volume IV

Supplying and placing in position Conference table 10 seater Table equipped with a soft- closing wooden access flap for easy power and data connectivity. It should have provision for concealed wire management system under the worktop. The worktop's should have AV range containing integrate cable cubby and retractor provision. All material shall be of Godrej/ Durian/ feather lite make and colour. Size not less than L=300cm, W=115cm and H= 750cm. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 5 from Volume IV

Supplying and placing in position Executive High back Chair with quilted leatherette, height-adjustable lumbar support, height-adjustable armrests, coat hanger at the top and chrome pedestal at the bottom. It should enable two seat depth for different body structures, and a four-position locking mechanism. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 6 from Volume IV

Supplying and placing in position Executive High back Chair with height as well as tilt adjustable headrest and multi-flex active lumbar support for comfort and foam laminated fabric lumbar pad for back’s position. The armrests should be height adjustable offering comfort to elbows and forearms. It should offer two seat depth for different body structures. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 7 from Volume IV

Supplying and placing in position High back chair with in-built ergonomic adjustments for comfortable and elongated sitting position and with an adjustable lumbar support, seat height, headrest, armrests, multiple back locks, and back tilt positions. Confirming to BIFMA X5.1 standard. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 8 from Volume IV

Supplying and placing in position Executive High back chair with thick seat cushion in solid pop colours tubular-frame back and mesh upholstery. This light chair should be completed with slim, wide loop armrests. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 9 from Volume IV

Supplying and placing in position Visitor chair with thick seat, back cushions, wide contoured seat and back to keep for an upright position and centre tilt synchronous mechanism enables tilt tension adjustment. The armrests to be of Poly Propylene durable material with 100% VOC- free powder coating. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 10 from Volume IV

Supplying and placing in position High back with thick seat, back cushions and wide contoured seat and back to keep for an upright position and centre tilt synchronous mechanism enables tilt tension adjustment. The armrests to be of Poly Propylene durable material with 100% VOC- free powder coating. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) a. Single Seated 86Wx90.5Dx85.5H * Please Refer Sr. No 11 from Volume IV

Supplying and placing in position High back with thick seat, back cushions and wide contoured seat and back to keep for an upright position and centre tilt synchronous mechanism enables tilt tension adjustment. The armrests to be of Poly Propylene durable material with 100% VOC- free powder coating. All material shall be of Godrej/ Durian/ feather lite make and colour. All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) b. Two Seated 146Wx90.5Dx85.5H * Please Refer Sr. No 12 from Volume IV

Supplying & placing in position Centre table made up of wood with Easy access shelf neatly tucks and having smooth Walnut finish. All material shall be of Godrej/ Durian/ feather lite make and colour. Size not less than (L= 100cm, W=65cm and H=65cm). All works complete as per the drawing/ Image, technical specification and direction of the Engineer. (Please Note: the rate should be inclusive of loading & unloading charges, transportation charges, assembling charges, etc including lead of 500m and lift upto three level but excluding cost of GST.) * Please Refer Sr. No 13 from Volume IV

File Storage:- Supplying and installing in position storage in 19 mm thick Marine BWP (boiling water proof) plywood with shutters in 19mm thick BWP (boiling water proof) plywood fixed on SS. brush finished brass 'L' hinges & 100 mm height SS 304 grade handles. The cabinet to have 19mm thick plywood shelves fixed on shelf buttons, back sheet in 8mm plywood & finished with 1mm thick laminate externally and 0.8mm thick laminate internally. All exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate & with necessary labour, S.S brush finish hardware, cleaning, placing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. a. Size 1200mm(W)x450mm(D)x1200mm(H)

File Storage:- Supplying and installing in position storage in 19 mm thick Marine BWP (boiling water proof) plywood with shutters in 19mm thick BWP (boiling water proof) plywood fixed on SS. brush finished brass 'L' hinges & 100 mm height SS 304 grade handles. The cabinet to have 19mm thick plywood shelves fixed on shelf buttons, back sheet in 8mm plywood & finished with 1mm thick laminate externally and 0.8mm thick laminate internally. All exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate & with necessary labour, S.S brush finish hardware, cleaning, placing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. b. Size 1200mm(W)x450mm(D)x2400mm(H)

File Storage:- Supplying and installing in position storage in 19 mm thick Marine BWP (boiling water proof) plywood with shutters in 19mm thick BWP (boiling water proof) plywood fixed on SS. brush finished brass 'L' hinges & 100 mm height SS 304 grade handles. The cabinet to have 19mm thick plywood shelves fixed on shelf buttons, back sheet in 8mm plywood & finished with 1mm thick laminate externally and 0.8mm thick laminate internally. All exposed edges to be finished with teak wood lipping with 3 coats or more of melamine polish to match the shade of laminate & with necessary labour, S.S brush finish hardware, cleaning, placing in position etc. complete. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. c. Size 900mm(W)x450mm(D)x735mm(H)

E-HVAC I-High Side Air conditioning work VRV SYSTEM - Daikin Make Supply of Variable Refrigerant volume Modular type air-conditioning system with wide range of indoor and outdoor units, with low external static pressure. The system consists of multiple indoor units ranging from high wall, fan coil, ducted type, cassette type etc. Connected to a single or multiple modular type outdoor units with individual controllers to each indoor unit, refrigerant piping, control cabling and also centralized controller. The specifications and details are as below: OUTDOOR UNITS Supply of Modular type Top discharge outdoor units equipped with high efficient scroll compressors, with all inverter type compressors, special acryl pre-coated heat exchanger having high efficiency E-pass coil design, low noise condenser fan coupled with variable speed motor, auto check-function for connection error, auto addressing Including required no. of multi connection piping kit. Refrigerant Gas is eco friendly R410a. a. 18 HP

2. INDOOR UNITS Supply of Ceiling Mounted compact cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller a. 1.08 TR

Supply of Ceiling Mounted compact cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller b. 1.66 TR

Supply of Ceiling Mounted 4 way Cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller a. 2.08 TR

Remotes and Controls Cordless Remote for Compact cassette ype units

Remotes and Controls Cordless Remote for 4 way Cassette Type units

Supply of Refnet joints for branching of refrigerant.

Supply of 3 Star Rating DX Hi-wall type split airconditioner with Rotary compressor Cooling Only Inverter compitable for R-32 Refrigerant. The units shall be supplied wih cordless remote control. a. 1.5 TR -3 Star Inverter

Supply of 3 Star Rating DX Hi-wall type split airconditioner with Rotary compressor Cooling Only Inverter compitable for R-32 Refrigerant. The units shall be supplied wih cordless remote control. b. 2 TR -3 Star Inverter

II-Low Side Air conditioning work OUTDOOR UNITS Lifting, Shifting, Installation, Testing and Commissioning of Modular type Top discharge outdoor units equipped with high efficient scroll compressors, with all inverter type compressors. Refrigerant Gas should be eco friendly R410a a. 18 HP

INDOOR UNITS Installation, Testing & Commissioning of Compact cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller a. 1.08 TR

Installation, Testing & Commissioning of Compact cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller b. 1.66 TR

Installation, Testing & Commissioning of Ceiling mounted 4 way Cassette type indoor unit motor, 3 step control, in built eletronic expansion valve, washable filter. The Unit shall be supplied with cordless remote controller a. 2.08 TR

Installation, testing & commissioning of Refnet joints for branching of Refrigerant Piping.

Installation, testing & commissioning of of 3 Star Rating DX Hi-wall type split airconditioner with Rotary compressor Cooling Only Inverter compitable for R-32 Refrigerant. The units shall be supplied wih cordless remote control. a. 1.5 TR -3 Star Inverter

Installation, testing & commissioning of of 3 Star Rating DX Hi-wall type split airconditioner with Rotary compressor Cooling Only Inverter compitable for R-32 Refrigerant. The units shall be supplied wih cordless remote control. b. 2 TR -3 Star Inverter

VRV Refrigerant Piping Supply, installation, testing & commissioning of copper piping with necessay fittings and Supports and with nitrile rubber tubular insulation of suitable thickness.

DX Refrigerant Piping Supply, installation, testing & commissioning of copper piping with necessay fittings and Supports and with nitrile rubber tubular insulation of suitable thickness.

Supply & installation communication cable from indoor to outdoor unit a. 2 core x 1.5 Sq.mm flexible cable

Supply & installation communication cable from indoor to outdoor unit b. 3 core x 1.5 Sq.mm flexible cable

Drain Piping Supply, Installation and Commissioning of PVC piping complete with fittings, supports as per specifications and insulated with 6mm thick nitrile insulation etc., complete as per technical specifications. a. 25 mm dia

Supply, installation, testing & commissioning of VRV MS frame work for Outdoor unit with necessary supports

Supply, installation, testing & commissioning of DX MS frame work for Outdoor unit with necessary supports

Electrical Cable Material , installation , testing & commissioning of Electrical and Communication Cabling. a. 4 Core x 10 Sq. mm Cu Cable

Material , installation , testing & commissioning of Electrical and Communication Cabling. b. 3 Core x 1.5 Sq. mm Cu Cable

Supply & installation of Additional gas charging for VRV System.

F-ELECTRICAL WORK Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (c) Group C -- with Cat A Modular Accessories

'Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required'.(a) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required.'(a) 1 or 2 Module ( 75 mm x 75 mm) Cat A

'Installation,earthing, testing and commissioning of ceiling fan including wiring the down rod of standard length ( upto 30 cm) with 1.5 sq .mm FRFRLS PVC insulated copper conductor single core cable etc. as required.

'Supplying and fixing extra down rod of 20 cm length GI pipe 15 cm dia heavy gauge including painting etc as required

'Supply and erecting 'J' type Mild Steel fan hook fabricated out of 35 X 6 mm flat strip suitable for rafters complete with coach screws etc as required.'(c) For 8 inches rafter size

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required.'(a) Cat A

Supplying and fixing call bell/ buzzer suitable for single phase 230 V complete as required : Ding Dong Bell

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator). : 4 way single door Cat A

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) : 8 way (8+24), double door, Horizontal type Cat A

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. : TPN, Cat A

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. : TPN, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. : SP, Cat A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. a. 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. b. 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. c. 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. j. 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit(heavy) of appropriate size as required. k. 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT A

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT A

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with modular TV socket including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. CAT A

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required'(a) Cat 6

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required.'(a) 2 Pair

Supplying and drawing of Co-axial TV cable of required grade, solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required (b) RG-6

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. a. 20 mm

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. b. 25 mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. : 3 1/2 Core 70 sq.mm

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required : 3 1/2 x 70 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm in the existing masonry open duct, etc. complete as required

Supplying and laying 25 mm x 5 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. '(a) Cat A

Supply and erecting of 12 inch (300 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories.(a) Cat A

Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone makemodules, crimping and terminations, etc. complete as required. : 50 Pair

Supplying and fixing 12U wall mount rack (Dimension-DxWxH – 500x550x613 mm) as per specification no. WG-NAS/RAK

Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP

Supplying, installing and testing UTP connector (RJ-45) as per specification no. WG-NAS/UTPC.

Supplying and erecting 12-15W COB Recess Mounted Fixed Down Light ( Make : Philips- thin Trim deep Reccessed COB , Jaquar - LERS02R015XW or Equivalent to same as per architecture requirement )

Supplying and erecting 5-7W COB Recess Mounted FLEXI Beam Light ( Make : Philips- Flexi Beam Reccessed COB , Jaquar - LETS36R003XW or Equivalent to same as per architecture requirement )

Supplying and erecting 15-18W Slim Panel Light ( Make : Philips- Dura Slim, Jaquar - LARP01R018XW or Equivalent to same as per architecture requirement )

Supplying and erecting 10W Wall Light ( Make : Philips- Meraki-282109 or Equivalent to same as per architecture requirement )

Supplying and erecting 22W Slim Panel Light ( Make : Philips- Dura Slim, Jaquar - LSKL01S036XW or Equivalent to same as per architecture requirement )

Supplying and erecting 28W Pendent Light ( Make : Philips- lustre or Equivalent to same as per architecture requirement )

Supplying and erecting 28W LED strip Light - 5 mtr ( Make : Philips- Linea Bright or Equivalent to same as per architecture requirement )

Supply and Fixing of 6M Pop-up Box with 2 NOS 5A SOCKET ,1 NOS 5A SWITCH and 1 Nos Data Socket

I-DEPwD ACCESSIBILITY RETROFITTING Parking Signage Design, supply, fabrication and fixing of SS 304, non glare Signage board (2 ft. x 2 ft.- 1 no.) for the accessible parking, as per the approved design and make, having 1.2 mm thick SS non glare approved colour base plate having the 'Universal Accessibility Symbol' and Upper case Sans Serif words of height 50mm engraved on it along with the equivalent word/s written in Hindi using Devnagri script of height 50mm. Letters, words and symbols to be of the approved colour such that there is adequate visual contrast with the base plate. Signage to be installed at a height of 2100mm from the ground level using a post of MS hollow square section (50mm x 50mm) as per the installation procedure specified by the manufacturer and as per the drawing issued and up to the satisfaction of the engineer in charge.

Building entrance and Accessible entrance signage Design, supply, fabrication and fixing of SS 304, non glare multilingual Braille (raised domes) entrance signage (size 1 ft x 1 ft) as per the approved design and make,indicating the name of the building/ accessible entrance location. Having 1.2mm thick SS non glare approved colour base plate with the 'Universal Accessibility Symbol' and Upper case Sans Serif words of height 20mm engraved on it along with the equivalent word/ s written in Hindi using Devnagri script of height 20mm. Letters, words and symbols to be of the approved colour such that there is adequate visual contrast with the base plate having anodized aluminium strip comprising of Grade 1 Braille consisting of raised domes of 1.5 to 1.6mm dia. and spacing as per Braille standards given by GOI, to be die punched on reverse side and be raised 0.6 to 0.9mm above base plate.The signage to be installed at the specified location on the compound wall near the site entrance gate installed at a height of 1200 mm from the finished ground/ floor level, using the necessary hardware specified by the manufacturer and to be installed up to the satisfaction of the engineer in charge.

Tactile Floor Map with QR Code lined to audio feedback Design, supply, fabrication and fixing of acrylic, non glare, tactile pictorial building layout of size 2ft x 1.5ft min., of the approved design and make, having 6mm thick acrylic non glare base plate of the approved colour and non glare acrylic cut out symbols and upper case Sans Serif letters of height not less than 12mm, with the equivalent word/s written in Hindi with acrylic cut out Devnagri letters of height not less than 12mm, raised 1 to 2mm above base plate and of the approved colour such that there is adequate visual contrast with the base plate. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the tactile floor map. Grade 1 Braille consisting of PVC rasters of 1.5 to 1.6mm dia. having rounded tops inserted by a raster pen or automatic insertion tool into the holes made by a rotary engraver to be integral with the sign face and be raised 0.6 to 0.9mm above base plate. Braille spacing to be as per Braille standards given by GOI. The map to be installed at the specified location as per accessibility standards, shall be oriented to the position of the viewer and to be installed at a height of 800 mm from the finished ground/ floor level and using the necessary hardware specified by the manufacturer and to be installed up to the satisfaction of the engineer in charge.

Overhanging directional signage Design, supply, fabrication and fixing of acrylic, non glare multilingual overhanging signage (size 2ft x 2ft 6 inches) of the approved design and having 6mm thick blue/ approved colour acrylic base plate with Upper Case San Serif made of acrylic non glare cut out letters of height not less than 30mm, raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 12mm raised not less than 0.8mm above base plate. Signage to have a relevant symbols made of cut out acrylic and raised by 0.8mm above base plate. Letters, words and symbols to be white/ of the approved colour such that there is adequate visual contrast with the base plate. The signage to be installed at the specified location by suspending it from the ceiling using the hardware specified by the manufacturer and as per the direction of the engineer in charge

Door and Directional signage :6" x 9" format (with symbols / without symbols) Design, supply, fabrication and fixing acrylic multilingual Braille (raised domes) signboards of size 6"x 9" for directions and room titles, designed as per the drawings issued and having 4mm thick blue/ approved colour acrylic non glare base plate with Upper Case San Serif words made of acrylic non glare cut out letters of height 15mm raised 0.8mm above base plate and the equivalent word/s written in Hindi with Devnagri non glare acrylic letters of height 15mm raised 0.8mm above base plate. Signage to have a relevant symbol made of cut out acrylic and raised by 0.8mm above base plate. Letters, words and symbols to be white/ of the approved colour such that there is adequate visual contrast with the base plate. Grade 1 Braille consisting of PVC rasters of 1.5 to 1.6mm dia. having rounded tops inserted by a raster pen or automatic insertion tool into the holes made by a rotary engraver to be integral with the sign face and be raised 0.6 to 0.9mm above base plate. Braille spacing to be as per Braille standards given by GOI. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the signage. Each signboard to be fixed using double sided bonding tape of 3M/ equivalent brand or mirror screws, at 1200mm from FFL and up to the satisfaction of the engineer in charge.

Floor Directories with tactile letters Providing and fixing acrylic multilingual Braille (raised domes) floor directories on all floors of size 1.5 ft x 2 ft , showing the list of rooms on that floor, to be installed on each floor near the staircase, designed as per standards and having Base plate: 4mm thick blue/ approved colour acrylic non glare Text: Upper Case San Serif words made of white acrylic non glare cut out letters of height 20mm raised 0.8mm above base plate and the equivalent word/s written in Hindi with Devnagri non glare acrylic letters of height 20mm raised 0.8mm above base plate. Symbols: Signage to have relevant symbols made of cut out acrylic and raised by 0.8mm above base plate. Arrows: Signage to have arrows pointing in the relevant direction made of cut out acrylic and raised by 3mm min. above base plate Letters, words and symbols to be white/ of the approved colour such that there is adequate visual contrast with the base plate. Braille: Grade 1 Braille consisting of PVC rasters of 1.5 to 1.6mm dia. having rounded tops inserted by a raster pen or automatic insertion tool into the holes made by a rotary engraver to be integral with the sign face and be raised 0.6 to 0.9mm above base plate. Braille spacing to be as per Braille standards given by GOI. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the floor directory.Each signboard to be fixed using double sided bonding tape of 3M/ equivalent brand or mirror screws, at 1200mm from FFL and up to the satisfaction of the engineer in charge.

Emergency Evacuation signage (6" x 9" format) Design, supply, fabrication and fixing acrylic multilingual Braille (raised domes) signboards of size 6"x 9" emergency exits and evacuation instructions, designed as per the drawings issued and having 4mm thick green/red acrylic non glare base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height not less than 15mm raised 0.8mm above base plate and the equivalent word/s written in Hindi with Devnagri non glare acrylic letters of height not less than 15mm raised 0.8mm above base plate. Grade 1 Braille consisting of PVC rasters of 1.5 to 1.6mm dia. having rounded tops inserted by a raster pen or automatic insertion tool into the holes made by a rotary engraver to be integral with the sign face and be raised 0.6 to 0.9mm above base plate. Braille spacing to be as per Braille standards given by GOI. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the signage. Each signboard to be fixed using double sided bonding tape of 3M/ equivalent brand or mirror screws, at 1200mm from FFL and up to the satisfaction of the engineer in charge.

FIRE ORDER Design, supply, fabrication and fixing multilingual FIRE ORDER signage of size 750mm x 900mm made out of Ecosolvent self adhesive, non-reflective, opaque vinyle print, pasted on 3mm thick PVC foam sheet. One braille module of size 9 x 9 inch included .Signage giving evacuation instructions during fire using black/ red/ green non glare Upper Case Sans Serif words of height not less than 15mm and the equivalent translation written in Hindi using Devnagri non glare black letters of height not less than 15mm , designed as per the drawings issued. Each signboard to be fixed using double sided bonding tape of 3M/ equivalent brand or mirror screws, at 1200mm from FFL and up to the satisfaction of the engineer in charge.

Emergency evacuation map: photoluminiscent Providing and installing an Emergency evacuation map of each floor indicating the current position of the viewer saying "YOU ARE HERE" of 15mm high letters in red/ green /black with white background, indicating the emergency exits, locations of fire extinguishers etc. Signs shall have a solid header with the text “EVACUATION PLAN” in contrasting uppercase letters not less than 3/4" in height. The size of the board shall be 2ft x 2ft made out of Ecosolvent self adhesive,reflective, opaque vinyle print, pasted on 3mm thick PVC foam sheet, complete with wall mounting arrangements with mirror fasteners and shall be installed at a height of 1200mm from FFL and shall be oriented to the position of the viewer up to the satisfaction of the engineer in charge. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the tactile floor map

Photoluminescent Fire exit and floor identification signage with Braille: PHOTOLUMINISCENT Fire Exit and floor identification signage of size 400 x 150 mm min. made out of computer cut opaque, non reflective, self adhesive vinyle letters, pasted on a self adhesive photoluminiscent film, pasted on 3mm thick PVC foam sheet, having a 2mm acrylic baseplate. Braille strip comprising of Acrylic base plate and PVC rasters to be provide below the signage. Signage to be of the approved colour with wall mounting arrangements with mirror fasteners and shall be installed at a height of 1200mm from FFL and up to the satisfaction of the engineer in charge.

Anodised Aluminium Braille Indicators with SS - 304 cable fasterners for handrails Providing and fixing 0.8 mm thick Stainess Steel pre rolled signs of size 100mm x 80mm to fit any handrail circumference with no add ons that can be picked off or removed and having the required word written in Grade 1 Braille (raised domes of 1.5 to 1.6mm dia. and spacing as per Braille standards given by GOI) raised by 0.6mm to 0.9mm above base plate. To be installed in place around the handrail using SS-304 cable ties of dimension 7.9mm x 200mm with press fit mechanism.

Door signage : 6" x 3" format (without symbols, without text, only Braille) Design, supply, fabrication and fixing acrylic Braille (raised domes) signboards of size 6""x 3" for room titles, designed as per the drawings issued and having 4mm thick blue/ approved colour acrylic non glare base plate. Grade 1 Braille consisting of PVC rasters of 1.5 to 1.6mm dia. having rounded tops inserted by a raster pen or automatic insertion tool into the holes made by a rotary engraver to be integral with the sign face and be raised 0.6 to 0.9mm above base plate. Braille spacing to be as per Braille standards given by GOI. A navigational QR code solution from Spacefelt or equivalent linked to audio navigation feedback compatible to Android and IOS to be integrated with the tactile floor mapEach signboard to be fixed using double sided bonding tape of 3M/ equivalent brand or mirror screws, at 1200mm from FFL and up to the satisfaction of the engineer in charge."

Providing and installing on all floors a building an audio navigational and wayfinding system of Disha / Iwayplus brand or equivalent based on BLE Beacons and custom app for use on smart phones, integrated with QR codes in designated locations enabled with AR/VR technology as per manufacturers specifications.Cost to include generation of CAD files for as built layouts of all structures. The scope of work includes entire mapping of building and providing requisite number of Beacons as per manufacturers specifications to cover the navigation needs for entire campus. Each Set to contain a module of 30 beacons

Modular Unisex Accessible Toilet : Providing and installing in position a prefabricated modular unisex accessible toilet unit of size 2200 x 2100 mm as per accessibility norms fabricated out of SS, GI framing and panelling surfaces along with ACP exterior surafce as per manufacturers specifications inclding all service lines for water supply and drainage. ech Specifications for Prefabricated Accessible Toilet in India 1. Structure: Frame: GI (Galvanized Iron), powder-coated for durability, 2mm thickness. Cladding: ACP (Aluminum Composite Panel), 3mm thickness, weather-resistant, available in matte, glossy, or wood finishes. 2. Flooring: Anti-slip vinyl or rubber flooring (3mm thickness), water-resistant, slip-resistant, and easy to clean. 3. Roof: ACP or insulated roofing panels, weather-resistant, soundproof, and thermal-insulated. 4. Doors & Windows: Doors: Minimum 900mm width for wheelchair accessibility. Windows: Frosted glass for privacy, small, strategically placed. 5. Accessibility Features: Interior Layout: 1500mm turning radius, wheelchair-friendly. Grab Bars: Stainless steel or powder-coated at appropriate heights. Toilet Seat: Accessible height (450-480mm) with side armrests. Shower Area (Optional): Foldable seat, handheld shower. 6. Ventilation & Lighting: Exhaust fan or louvered windows for ventilation. LED lighting, energy-efficient with diffused light. 7. Plumbing & Electrical: Plumbing: PVC, water-efficient fixtures. Electrical: Waterproof outlets and fixtures, placed at accessible height (1.2m). 8. Durability & Maintenance: Corrosion-resistant materials (GI, ACP), easy to clean, low maintenance. 9. Sustainability: Eco-friendly, recyclable materials. Energy-efficient features (LED lights, water-saving fixtures). Optional Additions: Solar panels, rainwater harvesting, automated doors, and smart sensors.

Concept Creator (BID ID -52038)

AAI JEE INTERIORS (BID ID -51941)

Desh Pande Construction (BID ID -52096)