PROVIDING FINISHING FOR FRONT ELEVATION, FIRE FIGHTING ARRANGEMENTS, RAIN WATER HARVESTING ARRANGEMENTS, ADDITIONAL AMENITIES, ACCESSIBILITY TO PHYSICALLY CHALLENGED PERSONS IN NEWLY CONSTRUCTED SHOP CUM COMMERCIAL COMPLEX BUILDING FOR PSG EMPLOYEES

Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

PLAIN CEMENT CONCRETE 1:5:10 (One cement, five M - sand and ten aggregate) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers.

Manufacturing, supplying fixing of RCC PRECAST RING of 1.50m diametre of slab 0.30m height in cement concrete 1:2:4(One cement, two M - sand and four aggregate) using 20mm gauge hard broken granite stone metal including cost of moulding and including cost of reinforcement of 10 to 6mm dia rod at 15cm centre to centre in both direction and plastering the top side with cement mortar 1:3(One cement and three P - sand) 6mm thick including finishing and curing etc., including cost of materials, conveyance at site of works, loading and unloading and fixing in position with all necessary accessories etc., complete complying with standard specification as directed by the departmental officers. [ The materials should be got approved by the departmental officers before execution].

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 75mm thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using 20mm HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling 40mm gauge metal in DISPERSION TRENCH etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling 20mm gauge metal in DISPERSION TRENCH etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing P.V.C. Rainwater Downfall pipes of 110mm diametre 4Kg / m^2 with necessary shoes, bends and other speicals, clamps, screws, nails, teakwood plugs etc., complete including cost of all materials. The rate is to include cost of removable cast iron Gratings of appropriate size. The size of teakwood plugs to be used is 150mm * 25mm in front and 200mm * 75mm in rear and all other sides with a depth of 100mm. The pipe is to be fixed by means of "U" clamps at the cnetre of the pipe screwed to the plugs. The special type of 'U' clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipe length, complete complying with standard specification. ONE FLOOR.

Paving the floor with best quality TACTILE PAVER TYPE OF NEW TEK BT YELLOW COLOUR CERAMIC TILES of size 305 X305 X15mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Manufacturing, supplying and fixing of Teakwood ornamental Entrance Main door with the following specification. The outer frame of ornamental Entrance Door of size 150x100mm.Teak wood scantling. The door consists of openable area with Double leaf. The Shutter bottom rail is of 200x50mm size and middle, top and side rails are of size 150x50mm with corner designed beading works. The shutter pannel is of 40mm thick T.W.planks with special curving works. The outer frames corners are designed border works single side for entrance outer frame. The cost includes all kinds of furniture fittings, such as Brass Aldrop, Brass tower bolt, brass hinges, brass door stopper, brass handles. All the members are finshed with two coats of melamine polish with outer priming coat. (The quality of all furniture fittings should be got approved by the Executive Engineer before use.)