Loading
Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹2.4 L
Closing Date
10 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SNT WORK
19 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited.The average annual contractual turnover shall be calculated as an average of 'Total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender as per Annexure- G of tender booklet.
b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway.
In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Definition of Similar Work:- Any signal interlocking work having indoor work.
31 conditions · 26 needing a document upload
Please furnish list of Works completed in last seven financial years giving Description of Work, Organization for whom executed, approximate value of contract at time of award, Date of award and Date of Completion. Date of actual Start, Actual Completion and Final value of Contract shall also be given. Annexure -G.
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Documents to be Submitted Along with Tender: (i)The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company /Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii)Following documents shall be submitted by the tenderer
(a)Sole Proprietorship Firm: All documents in terms of Para 10 of the Tender Form (Second Sheet) above (As per GCC-2022). (AFFIDAVIT BY SOLE PROPRIETORSHIP FIRM as per Annexure-O-1 in tender document)
(b)HUF: i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.as per GCC-2022.
(c)Partnership Firm: All documents as mentioned in para18 of the Tender Form (Second Sheet) as per GCC-2022.As per GCC- 2022. (Annexure-O-2 of tender booklet.)
d) Joint Venture (JV): All documents as mentioned in para 17 of the Tender Form (Second Sheet).as per GCC-2022.
(e)Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.(Eligibility Criteria) above as per GCC-2022. (Annexure-O-10 of tender booklet.)
(f)(i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet)..(Eligibility Criteria) above as per GCC2022. (Annexure : O-11 O-12 & O-13 of tender booklet.)
g)Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer whether sole proprietor/ a company or a partnership firm/registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected.
Please submit your correspondence address, e-mail ID and valid phone number.
Please submit your bank details i.e. Name of the Bank along with Bank Branch Code, Account Number, IFSC Code, and PAN Number.as per annexure -J of tender booklet.
Please furnish list of plant and Machinery available on hand own and proposed to be inducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value, Approximate value of balance work yet to be done and Date of award
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Each page of the tender papers will be treated as signed/accepted by the tenderer(s) or such person(s) on his/their behalf who is/are legally authorized to sign for him/them.
Any DIPP certificate submitted along with the tender document for, exemption of EMD should be valid on the date of opening of the tender, else the tender offer will be summarily rejected.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Declaration form regarding site etc. as per annexure -C of tender booklet.
Declaration regarding constitution of firm as per Annexure-D of tender booklet.
Engineers/Personnel as per annexure -F of tender booklet.
Performa of Completion Certificate as per annexure -L of tender booklet.
The tenderers may also upload the following documents along with his/their tender: The tenderer may upload statement, which shall contain organizational set up and working systems to be adopted by the successful tenderer s during the operation of the contract. It shall contain the details of man power and machineries in the prescribed format and details of methodology for planning, execution, monitoring and completion of the project. The methodology so adopted shall suit to the nature of work and shall also comply fully with best practice and current regulations. A comprehensive detailing for each activity like setting-up organization, safety plan, execution plan, quality assurance plan, sequence of work to achieve the mile stones, ensure targeted progress and quality and in turn deployment of resources, risk analysis and its mitigation strategy shall be given communication arrangement within his organization and with the railways for decisions, progress or any other matter connected with this project to ensure full information about the project including progress of work at different time scale shall also be furnished.
List of works completed in the last seven financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work. Date of actual start, actual completion and final value of contract should also be given.
Supportive documents/certificates from the organizations with whom they worked/are working as list of works completed and list of works on hand should be enclosed.
List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award .annexure -H
Uploading of declaration regarding Employment/Partnership etc. of Retired Railway Employees as per GCC-2022 as per annexure -Q of tender booklet.
Uploading of Tender Forms shall embody the contents of the contract documents either directly or by reference and shall be as per specimen form, Annexure-I. e-Tender Forms shall be issued free of cost to all tenderers.
A copy of certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of the certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm. Annexure-V(A) shall also be submitted by the each member of a partnership firm/Joint Venture (JV)/ Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be.Non submission of a copy of certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he are/is qualifying the Qualifying Criteria mentioned in the Tender Document. (As per Railway board letter no.2022/CE-l/CT/GCC- 2022/Policy dt. 13.12.2022)
Provision of Signaling and Telecom work for additional loop line at Sarkanpur and Ishanagar Station on Lalitpur -Khajuraho Section of Jhansi Division.
JHS-N-GSU-05-26
JHS-N-GSU-05-26
Open
Works - General
12 Months
Jhansi, Uttar Pradesh
₹0
₹2.4 L
10 Mar 2026
16 Feb 2026
24 Feb 2026
154 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,17,56,035.83 | ||
| — | 3000.00 | — | — | ||
| "Supply of 16/0.2 mm (0.5 sq mm) PVC insulated multi strand, single core, tinned copper conductor, as per RDSO Specn. No.IRS:S-76/89 (Amnd-3) or latest. Each coil should be of 100/200/500 meters length. Colour of the wire will be specified by the Engineer incharge." (Inspection Agency by consignee) | — | — | — | 32,250 | |
| — | 30.00 | — | — | ||
| Supply of Apparatus Case/Location Box Full as per RDSO drg. no. RDSO/S-11500 or latest, with 'E' type lock and key ward no. 42,. The key and handle should be supplied at the rate of one no. per four Apparatus cases. The 'E' type key lock is as per RDSO Spec. IRS;S-30/64 or latest, RDSO drg. no.SA 3376/M or latest and Key is as per Drg. No. 3377/M or latest. Note: This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. (Inspection Agency by consignee) | — | — | — | 8,24,994.3 | |
| — | 16.00 | — | — | ||
| Supply of Apparatus Case / Location Box Half as per RDSO drg.no. RDSO/S- 11507 or latest, with 'E' type lock and key ward no.42,.The key and handle should be supplied at the rate of one no. per four Apparatus cases. The 'E' type key lock is as per RDSO drg. no. SA3376 / M or latest and Key is as per Drg. No. 3377/M or latest. Note:This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys.(Inspection Agency by consignee) | — | — | — | 3,18,475.04 | |
| — | 6.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area THREE Aspects, complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23002 A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev latest and FRP material as per RDSO SPEC. No. or RDSO/SPN/151/1997 or latest. (Inspection Agency by consignee) | — | — | — | 2,14,424.22 | |
| — | 6.00 | — | — | ||
| "Multi section Digital Axle Counter (MSDAC) supply, design, installation, testing and commissioning of multi section digital axle counter (MSDAC) complete system as per RDSO Specification INo.RDSO/SPN/176/2013 version 3 with Latest amendments or latest. Suitable for commissioning of yard/Auto Section / dual detection (DCTC/AFTC with MSDAC). MSDAC should have facility to reset track sections. Design of axle counter circuit indoor installation testing and commissioning of multi section digital axle counter (per unit), supply of essential 10% spares covering all types of cards, 'wheel sensors for MSDAC . Supply of Diagnostic system for Remote diagnostics Tool set for wheel sensor mounting and maintenance of MSDAC consisting of torque wrench, ratchet, testing plate , measuring tape , screw driver, gloves and multimeter fluke 115 (1 Nos. per 14 DP). " "NOTE-1 : 1. If any housing is required to keep outdoor equipment, it has to be supplied with the equipment with no extra cost. 2. Maintenance free earthing (supply and installation) for track device/mushroom housing etc to be done by the contractor if required by system design. No extra cost/ payment will be made by this Railway: 3. Automatic resetting facilities through hardware /software for auto resetting to be |provided by contractor by his own materials for this no extra cost /payment will be made by Railways. 4. MSDAC system networking to be done with central control room. Required hardware PC/ network equipment to be provided by the contractor, no extra cost/payment will be made for this by Railway. E1 Channel/media will be provided by Railway for this purpose from nearest Railway station. 5. All other Hardware like TPR, Extra card to make dual DP, Modem, ethernet switches etc if required for commissioning and final track section pick up will be supplied by contractor, no extra payment will be made by this Railway. 6 Separate evaluator for UP and Down line to be provided at Station/RH as decided by Railway site engineer. For the communication between evaluator to evaluator (RH to Station) Quad/ OFC Link (dark fiber) will be provided by Railway. Any other Networking equipment if required will be supplied by contractor at no extra cost. 7. Manual resetting through reset box at station to be provided as per requirement." (Inspection Agency by RDSO) | — | — | — | 19,05,399.72 | |
| — | 80.00 | — | — | ||
| Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, 2V, 80 AH, in dry condition, shelf mounting type, conforming to RDSO Specn.No.IRS:S-88/2004 or latest, with inter cell connectors, nuts and bolts, washers, microporous vent plug, float etc.(Inspection Agency by RDSO) | — | — | — | 2,55,636.8 | |
| — | 24.00 | — | — | ||
| Supply of Track feed Battery Charger as per RDSO Specn. No.IRS: S-89/2013 Ver. 1.0 or latest. Charging capacity rating should be suitable for charging 80 AH Battery. (Inspection by RDSO). | — | — | — | 1,41,613.44 | |
| — | 48.00 | — | — | ||
| Supply of B Type Choke as per RDSO Specn.No.IRS:S-65/83 (Amnd. 3) or latest. The materials to be procured from RDSO approved firm I ((Inspection Agency by RDSO) | — | — | — | 2,83,638.24 | |
| — | 24.00 | — | — | ||
| Supply of Adjustable Track Feed Resistance 30 Ohms (Disc Type), Phenolic moulded base, as per RDSO Drg . No. SA-20161-66/M or latest. The materials to be procured from RDSOQ approved firm (Inspection Agency by RDSO) | — | — | — | 54,714.72 | |
| — | 27.00 | — | — | ||
| Q-Series Track Relay (QTA2 Type), AC immunized, 9 Ohms, 2F/1B along with plug board (base plate), connectors, retaining clips etc and conforming toBRS: 939A & 966(Appendix F2) or latest and RDSO Specn.No. IRS : S -34 , S - 23 , S - 60 or latest, as applicable.The interlocking code for this unit shall be "FGHKX".(Inspection by RDSO). | — | — | — | 1,02,687.75 | |
| — | 30.00 | — | — | ||
| Q-Series Neutral Line Relay(QSPA1 Type), AC immunised, 24V DC,8F/4B along with plug board (base plate), connectors, retaining clips etc and conforming to BRS-933A and RDSO Specn.No.IRS:S@ 45"44@ S-23, S 60 or latest, as applicable. Th e interlocking code for this unit shall be "ABDEJ" (Inspection Agency by RDSO) | — | — | — | 1,81,692 | |
| — | 50.00 | — | — | ||
| Q-Series Line Relay (QNA1 Type), AC immunized, 8F/8B, 24 V DC along with plug board (base plate), connectors, retaining clips etc. and conforming to BRS-93 1A and RDSO Specn. No. IRS : S-34 , S -23 , S - 60 or latest, as applicable. The interlocking code for this unit shall be "ABDGH".(Inspection by RDSO). | — | — | — | 2,21,962 | |
| — | 6.00 | — | — | ||
| Supply of Off set brackets for Shunt Signal, made of Mild steel, outer diameter 89 mm (3.5 inch), thickness of pipe 4.5 mm with fixing arrangement on Shunt Signal post as per Drawing No. SA-23080/Adv. along with fixing U bolts, nuts and clamps.(Inspection Agency by consignee) | — | — | — | 11,387.28 | |
| — | 6.00 | — | — | ||
| Supply of Position Light Shunt Signal Unit Complete, Non-Metallic, made of FRP as per Drg. No. SA-23840 (Adv.) suitable for LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item) (Inspection Agency by consignee) | — | — | — | 89,374.74 | |
| — | 1000.00 | — | — | ||
| Supply of Channel pins, single groove, 7 mm, galvanised, suitable for 4 mm dia bonding wire for Track Circuit rail bonding, as per RDSO spec. IRS: S 17-75 (Inspection Agency by consignee) | — | — | — | 4,550 | |
| — | 60.00 | — | — | ||
| Supply and installation of earth electrode as per standard practice and as per NCR Drawing no. S&T/CONST/6.4/97. It includes supply of GI pipe of 3m length. It includes connecting the earth electrode to the equipments which are required to be earthed including digging of earth pit 3 mtr deep and fixing earth electrode pipe, casting of cement concrete enclosure with cover (cover as per drawing no. S&T/CONST/6.3/97. It includes installation of 7 strand GI wires as earth lead wires, supported on MS flat size 5mm x 40 mm, soldering and nut bolt both, one end of both earth lead wire and MS flat to earth electrode and other end to Location boxes, block equipments, power equipments, cable sheath, signals etc. as per site requirement and as per instructions given by engineer incharge.(Inspection Agency by consignee) | — | — | — | 2,01,212.4 | |
| — | 8.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area TWO Aspects, complete without lenses, lamps and signal transformer as per RDSO Drg. No. SA 23003 A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest (Inspection Agency by consignee) | — | — | — | 2,50,464.64 | |
| — | 40.00 | — | — | ||
| Supply of Track Lead Juction Boxes as per C.Rly Drg.No.RST 11509 made from fiiber glass alongwith terminal blocks.(Inspection Agency by consignee) | — | — | — | 38,356 | |
| — | 6.00 | — | — | ||
| Supply of Offset brackets for Main Signal, made of Mild Steel, outer diameter 140 mm (5.5 inch), thickness of pipe 4.5 mm with fixing arrangement on Main Signal post as per Drawing No. SA-23080/Adv. along with fixing U bolts, nut and clamps." (Inspection Agency by consignee) | — | — | — | 7,239.54 | |
| — | 24.00 | — | — | ||
| Q-Series LED ECR (Universal Type i.e.QECX-61), 4F/4B complete with plug board(base plate), connectors, retaining clips etc and conforming to BRS:941A STS/E/RELAYS/AC LIT LED SIGNAL/09- 2002 ,Amdt.-1 or latest and RDSO Spec.No.IRS:S 45"44 S-23 or latest, as applicable.The interlocking code for this unit shall be ""ABDHK"". (Inspection Agency by RDSO) | — | — | — | 1,66,017.12 | |
| — | 12.00 | — | — | ||
| Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No. RDSO/SPN/197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 No. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 Nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 No.(d) Copper strip of 300x25x6 mm (MEEB) = 1 No. (e) Copper strip of 150x25x6mm (SEEB) = 1 No. |Gi) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate. (minimum 10 meter.) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter. ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable. (Inspection Agency by RDSO) | — | — | — | 2,16,510.24 | |
| — | 4.00 | — | — | ||
| Supply of Point group RRI, Siemens make or similar (No RSSK 3515/19) with base (Inspection Agency by RDSO) | — | — | — | 2,56,949.4 | |
| — | 2.00 | — | — | ||
| Supply of Route group RRI, Siemens make or similar (No RSSK31/0002) or latest and suitable for working with LED signals with base (Inspection Agency by RDSO) | — | — | — | 1,06,112.52 | |
| — | 10.00 | — | — | ||
| Supply and installation of Cable Termination(CT) rack as per drawing of NC Railway,complete along with fitting arrangements, wall supports, scaffolding and suitable grouting arrangements and also with arrangement for fixing four 8-way terminal strips/ Screw less terminals/ ARA terminals. The CT rack shall be covered with hylum sheet of minimum 10 mm thickness for fixing of 8-way terminal strips/ Screw less terminals/ARA terminals. Supply of 8 way terminal strips/ Screw less terminals/ARA terminals not covered under this item. Cable termination rack shall be corrosive resistant and powder coated. (Inspection Agency by consignee) | — | — | — | 4,71,468.4 | |
| — | 20.00 | — | — | ||
| Supply of hand cuff lock of Godrej/Navtal or reputed make with key and as approved by site engineer. (Inspection Agency by consignee) | — | — | — | 9,075.2 | |
| — | 2.00 | — | — | ||
| Supply of Relay Rack Assembly with scaffolding,fixtures and accessories including MS Bars for fixing of relay,plug board,string rods,fuse strips with bracket,11 Way Bus Bars with cover and mounting brackets,runway for cable/wires,frame,base,assembly etc.Siemens type & as per extant practice on the division. (Inspection Agency by consignee) | — | — | — | 68,672.2 | |
| — | 40.00 | — | — | ||
| Supply of stretcher bar insulation complete set consisting of the following:- Plate- T10367-1 No., Bush T- 10368- 3 Nos. and washer-T- 10371 -6 Nos. (Inspection Agency by consignee) | — | — | — | 15,259.6 | |
| — | 40.00 | — | — | ||
| Supply of gauge tie plate insulation complete set each set consisting plate T-10372 = 1No., Bush T-10368=3 Nos.and washer - T-10371 = 6 Nos.(Inspection Agency by consignee) | — | — | — | 15,277.6 | |
| — | 40.00 | — | — | ||
| Supply of IRS Type point machine 'D'/'P' bracket insulation complete set consisting of the following:- Plate LH - S-3266- 1 No, RH - S-3265-1 No., Plate S-8804- 1 No., Bush - S-3199 - 4 Nos, Bush S-8813- 2 Nos.(Inspection Agency by consignee) | — | — | — | 19,200.4 | |
| — | 10000.00 | — | — | ||
| Supply of indoor jumper wire ATC 1 x 0.6 mm dia NS04 0.5 Kilometre 2491.73 At Par 1245.87 as per specification IRS /S /76 /89 with latest amendment. (for size/parameters not covered by IRS-76/89 relevant clauses of 1S694/77 with latest amendment will be applicable) ( Red, Black & Grey) (Inspection by Consignee) | — | — | — | 24,900 | |
| — | 4.00 | — | — | ||
| Supply of Junction route indicator unit 2 way, made of FRP, (Without Lenses & Holder) as per Drg. No. SA 23401-06 (Adv.) (as applicable)suitable for LED Signal Lighting Unit and as per RDSO spec. IRS: S- 66/84 Amd.-1 or latest and RDSO/ SPN/ 194/2006 Rev.2 or latest. (Supply of LED Unit is not covered in this item).(Inspection by Consignee) | — | — | — | 1,81,834.44 | |
| — | 16.00 | — | — | ||
| Supply of Colour Light Signal Post, Tubular Mild steel, 4.5 meter length, 140 mm Dia, as per RDSO spec. No. IRS: S-6/81 or latest and Supply of cast iron Main signal surface base (As per RDSO Drg. No. 2011/M or latest), with CLS ladder assembly suitable for colour light signal 4.5 meter long, as per RDSO drg. No. SA 23153 and signal front staging complete assembly and complete signal back staging for CLS unit.(Inspection Agency by consignee) | — | — | — | 4,04,378.88 | |
| — | 8.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area TWO Aspects, complete without lenses, lamps and signal transformer as per RDSO Drg. No. SA 23003 A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest.(Inspection Agency by consignee) | — | — | — | 3,37,846.64 | |
| — | 8.00 | — | — | ||
| Supply of PVC indoor cable 1x40x0.6mmdia colour coding of insulation of inner core shall be in eight colours viz Blue,Red, Grey, Green, Brown, Block, Yellow &White as per specn IRS S 76/89 (Amd.-3)or with latest . (Inspection by Consignee) | — | — | — | 10,53,748.96 | |
| — | 8.00 | — | — | ||
| Supply of PVC indoor cable 1x60x0.6mm dia colour coding of insulation of innercore shall be in six colours viz Blue,Red,Green, Grey, Brown, & Black as perspecn IRS S 76/89 (Amd.-3) or with latest. (Inspection by Consignee) | — | — | — | 11,91,838.32 | |
| — | 38.00 | — | — | ||
| Supply of Phenolic laminated Sheet, resin bonded, grade P3 in standard size of 1220 X 1220 x 10 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied."(Inspection Agency by consignee) | — | — | — | 2,21,430.94 | |
| — | 3000.00 | — | — | ||
| Supply of Disconnect Terminal block for four conductors with screwing cage/clamp type, sliding switch disconnect, as per RDSO spec. RDSO/SPN/189/2004 Ver. 3.0 or latest, for each conductor size up to 2.5 sq. mm, equivalent of M6 terminals. Each terminal block equipped with two markers, on top and bottom, an end plate, two end clamps and adequate lenght of rails for fitting terminal blocks.(Inspection Agency by RDSO) | — | — | — | 5,78,160 | |
| — | 4.00 | — | — | ||
| Supply of PVC indoor cable 1x24x1 mmdia colour coding of insulation of innercore shall be in eight colours viz Blue,Red, Grey, Green, Brown, Block, Yellow &White as per specn IRS S 76/89 (Amd.-3)or with latest.(Inspection by RDSO) | — | — | — | 5,81,189.16 | |
| — | 5000.00 | — | — | ||
| Supply of ARA terminal block, made of PBT, as per RDSO spec. No. IRS:S75/2006(Rev.2)or latest and as per Drawing. No. SA-23741A (Alt.-4) or latest.(Inspection by RDSO) | — | — | — | 5,85,050 | |
| — | 2.00 | — | — | ||
| Supply of Position Light Shunt Signal Unit Complete, Metallic, Post type, along with Offset bracket, Hood, Cover, mounting socket etc as per Drg. No. SA-23840 (Adv.) or latest, suitable for LED Signal Lighting Unit.(Supply of LED Unit is not covered in this item) (Inspection by consignee) | — | — | — | 17,712.58 | |
| — | 2.00 | — | — | ||
| — | 2.00 | — | — | ||
| Supply of Offset brackets for Main Signal, made of Mild Steel, outer diameter 140 mm (5.5 inch), thickness of pipe 4.5 mm with fixing arrangement on Main Signal post as per Drawing No SA-23080/Adv. along with fixing U bolts, nut and clamps. (Inspection by consignee) | — | — | — | 2,413.18 | |
| — | — | — | 67,66,119.62 | ||
| — | 12.00 | — | — | ||
| Fixing, wiring, testing and commissioning of Electrical Point Machine 220MM/143MM on the Wooden/PRC sleepers at points as per standard practice and as per section of rails used. Item includes fixing switch extension bracket, providing insulation for switch extension bracket, fixing ground connection, adjusting opening of the switches and adjusting the point machine with crank handle. The item also includes: (i)Complete material for installation like ground- connections, switch extension brackets, point insulation material, I pipes, wiring materials, various fixing nuts & bolts including castle nuts, spring washers. (ii) All smithy & fitting works required at site for complete installation. (iii) Installation of gauge tie plate & providing insulation for gauge tie plate (Insulation in William Stretcher Bar will be provided by Railways). (iv) Wiring inside the point machine, insertion and termination of tail cable in point machine and junction boxes/location box /cable hut as per extent practice on NCR and the instruction of Railway Engineer at site. (v) Supply and fixing of bend pipes with welded frame for cable entry to machine (vi) Supply and filling of industrial grade/good quality lubricant/grease/oil for smooth operation of point machine Note ; The ground connections shall be suitable to the Point Machines as specified by Engineer- in-charge and shall be." "Suitable to the point lay out i.e. 60 Kg./52 Kg / 90R as per yard layout. Electrical Point Machine and M-6/Screw less terminals will be supplied by Railways /covered in Schedule separately | — | — | — | 1,73,417.16 | |
| — | 4.00 | — | — | ||
| Casting, concreting and curing of foundation for Position Light Shunt Signal as per Drg. No. NR/S&T/Const/2.2/97 using standard size of foundation/gal- vanized anchor bolts complete, required for erection of shunt signal post. An- chor bolts complete should comply with the RDSO drg. No. SA 116 A/M. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement sand mixture. Aggregate cement, sand and holding down bolts, will be supplied by contractor. Any machines and tools, if required for execution of this item, will be arranged/provided by contractor. | — | — | — | 14,674.64 | |
| — | 2.00 | — | — | ||
| Erection of CLS Post with base and signal unit on top or on Offset Bracket in- cluding erection of auxiliary signals like calling on, shunt signal if any. It in- cludes fixing of all LEDs and wiring of complete signal including route and aux- illiary signals, if any. It includes fixing of front and back staging, ladder and guards, signal name plates / boards, with contractor's own brackets and fixing materials. The work shall be done as per instructions of Railway engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer -In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. | — | — | — | 11,757.48 | |
| — | 2.00 | — | — | ||
| Erection of Position Light Shunt signal with Base, Post, Signal unit, complete fixing of LEDs and wiring of full signal. It includes fixing of Number Plates. The work shall be done as per instructions of Rly engineer at site. | — | — | — | 1,902.1 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
SIPISHANAGARSTATION2ndLoop.pdf
ATTACHMENT
SIPSARKANPURSTATION_.pdf
ATTACHMENT
TenderbookletIshanagarSarkanpur.pdf Tender booklet Ishanagar Sarkanpur
ATTACHMENT
IRGCC2022_1.pdf
ATTACHMENT
IRGCC2022ACS1_1.pdf
ATTACHMENT
IRGCC2022ACS2_2.pdf
ATTACHMENT
IRGCC2022ACS3_3.pdf
ATTACHMENT
IRGCC2022ACS4_1.pdf
ATTACHMENT
IRGCC2022ACS5_1.pdf
ATTACHMENT
IRGCC2022ACS6_1.pdf
ATTACHMENT
IRGCC2022ACS7_1.pdf
ATTACHMENT
AllAnnexurenew_1.pdf
ATTACHMENT
2021Tele523part13425647.pdf
ATTACHMENT
Annexure-VandAnnexure-V_A_.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.8ACS-8.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.9ACS-9.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.10ACS-10.pdf
ATTACHMENT
TenderbookletIshanagarSarkanpur.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .