8209 REPAIR AND CLEANING OF SEWAGE LINE, MANHOLES, SEPTIC TANKS, SOAKAGE WELLS, WATER TANK CLEANING, CLEANING OF DRAIN PIPES, REPAIR TO DRAIN ETC AND CERTAIN MISC WORK AT MIL STN SHAHJAHANPUR UNDER GE (E) BAREILLY.

Amount

M&L for Cleaning /clearing blocked sewage line 100mm to 300mm dia (PVC/ SGSW/RCC hume pipe) any depth by rodding between manhole to manhole manually and pumping out sludge water from manholes septic tank/soak well etc (where required) including providing trolley mounted pump set with suction pipe of adequate length and minimum 30 mtr delivery pipe including clearing spot blockages of WC, wash hand basins, sinks floor traps, NT and drainage pipes etc with and incl disposal of debris spoils and sludge hygiencially complete all a specified and directed. Notes:- The contractor shall keep the following aspect in mind while quoting unit rates in item above (i) The contractor / his authorise supervisor of the work will report daily at complain cell AGE B/R at 0830 hours to receive day to day all complaints. (ii) All sewage complaints must be attended immediatly on receipt but not later than 24 hours. (iii) Recovery (penalty) for not attending complaint beyond 24 hours shall be Rs. 200.00 per compaints per day delayed . (iv)The contractor shall be responsible for safety of workers (v) Contractor has been binded to strictly maintain cleaning of all area under jurisdiction of AGE B/R Shahjahanpur (vi) The contractor will be responsible to provide a proper dress code to workers and also provide all safetly.

Digging out sludge etc from oxidation pond, septic tank, sump well, man holes including depositing in pits where directed to a distance exc 50m but n exc 250m complete all as specified and directed. Note:- The unit rate quoted under this item shall deemed to include all the arrangement of necessary T&P with man and material for lifting up sludge from oxidation pond, septic tank, sump well, man holes, excavation of pit, deposing sludge and cover with earth complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided forcomplete all as specified and directed.

M&L precast cement concrete 1:2:4, type-B 1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc) Chula hoods, chajjas, water through managers shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed.

M&L mild steel bars (TMT) 10mm dia, and over cut to length bent to shape required including cranking, bending spirally for hoping ends for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 mtr wide but not exceeding 1.5 m in depth for foundation etc or for shafts, well cess pits manholes, pier holes etc and getting out in soft / loose soil complete all as specified.

Add to Srl item No.06 here in above for each additional 1.5 m or part thereof in depth beyond the first 1.5 Mtr.

Demolition and breaking up drain pipes 200mm internal dia of pipe (Salt glazed stone ware), AC or Reinforced concrete set in cement mortar.

Demolition and breaking up drain pipes 150mm internal dia of pipe (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

M&L 200mm bore salt glazed stone ware drain pipe laid in trenches and jointed complete all as specified and directed.

M&L 150mm bore salt glazed stone ware drain pipes laid in trenches complete all as specified and directed.

M&L plain cement concrete 1:4:8, type D2 (using 40mm graded stone aggregate) bed to 200mm bore drain pipes including packing under and hunching against the sides of the pipes after they are laid and tested in complete all as specified and directed.

M&L plain cement concrete 1:4:8, type D2 (using 40mm graded stone aggregate) bed to 150mm bore drain pipes including packing under hunching against the sides of pipes after they are laid and tested in complete all as specified and directed.

Retuning, filling in, including spreading, levelling watering and well ramming in layer not exceeding 25cm thick in soft/loose soil complete all as specified.

Removing excavated materials soils not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 40mm thick PCC 1:2:4, type B1 (using 20mm graded stone aggregate) laid in panel finished even and smooth with using extra cement as in flooring complete all as specified and directed.

Supply only glass dividing strip 3mm thick and 38mm wide in flooring complete all as specified and direcetd.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection/foot path finishing cement concrete even and smooth with out using extra cement complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for cement concrete 1:5:10, type E-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for preparation of sunken floor and applying a coat of hot bituminous primer @ .30 kg/sqm and applying a coat of industrial bitumen 85/25 @ 1.20 kg/sqm over primer and laying modified polymeric water proofing membrane(weight not less than 3 kg/sqm 2 mm thick consisting 100 mm micron HMHDE FILM ) and applying one coat of industrial btumen grade 85/25 @ 1.2 kg/sqm on top of membrane with 100 mm overlap at side end lap where required over 10 mm thick rendering in CM 1:4 including integral waterproofing compound 3% and taking down existing plastering as per manufacturer instruction and complete all as specified and directed

Removing existing water proofing treatment and preparing surfaces to the entire satisfaction of Engineer-in-Charge / GE including taking down existing plaster, cleaning of all foreign material such as grass, roots, dust etc and roughening the concrete surfaces by wire brushing and washing down to remove dust etc. flushing at junction of parapets complete and removing the same to the places where directed by Engineer-in-Charge

M&L for rendering 15mm thick on roof surfaces in CM 1:4 complete all as specified and direcetd.

M&L for preparation of roof surfaces, applying a coat of primer@ 0.40Kgs/sqm applying a coat of bitumen grade 85/25 @1.2kg/sqm supplying and laying water proofing treatment with using polymeric water proofing membrane (weight not less then 3kg/Sqm) consisting of 100 micron HMHDPE film centre core including applying a coat of bitumen 85/25 grade @ 1.2kg per sqm on top surface of membrane and torch application of membrane with 10cm overlap where required and finally finished with and including a coat of aluminium paint @0.20Ltr/Sqm as per manufacture instruction complete all as specified and directed.

Demolition of brick work in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles

M&L brick work with sub class B bricks burnt straight or curved on plan exc 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class ‘B’ old size bricks straight or curved on plan to any radius as in half brick thick wall built in CM 1:4 complete all as specified and directed

Taking down cement plaster including racking out joints hacking for key and scrubbing down with water etc. complete all as specified and directed

M&L rendering 15mm thick in cement plaster 1:4 on surfaces fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 15mm thick in cement plaster 1:6 on surfaces other than fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 10mm thick in cement plaster 1:4 on concrete surfaces of ceilling and finished the surface even and smooth without using extra cement complete all as specified and directed

M&L for two coats of cement base paint incl preparation of new surface of wall complete all as specified and as directed.

M& L for two coat of oil bound distemper incl preparation of new surface of wall complete all as specified and as directed.

M&L for 1mm thick (JK/Birla) Wall putty on wall all as specified and directed

M&L three coat of white wash on ceilling including preparation of new plastered surface and complete all as specified

Dismantling floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

S&F solid PVC door frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisiting of frame made out of MS tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20 mm which stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rails & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixing in the frame at site as per specification & drawing.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed as specified and as directed.

S&F 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm aluminium handles cast type, anodised complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n. exc 4 sqmeach complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but n exc 2 sqm each

S & F Mild steel work as in chowkats/frame of door or gates of angle or other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and inclu either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guisides) and hanging also fastening and fixing complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.

S & F 300 mm long mild steel sliding door bolts, ISI marked clip & bolt type, stove enamelled black, with bright bolt not less than 16mm dia with and including minimum 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F 2nd class hard wood glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel and fixed

S&F 150 mm long mild steel pressed handles oval type stove enamlled black complete all as specified and directed.

S&F 200 mm long mild Barrel tower bolt, oval type stove enamlled black with bright bolt and fixed

M & L preparing wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 3 mm thick sheet glass, Ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

S& F galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture1.18 mm complete all as specified and as directed .

M&L applying 2 coats of synthetic enamel paints on new steel surfaces over a coat of red oxide primer including surface preparation over 10 cm width and girth

Hacking out old broken glass of (any thickness, size, quality or description) from old wooden/steel frame, or stones, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for filling in bed block of hold fast etc complete all as specified and direcetd.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white(excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti symphonize pipe etc complete all as specified and as directed.

Supply only plastic water closet seat cover black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device

S&F in repair for CP Health Faucet with 1 Meter Flexible tube & Hook complete all as specified and directed.

S&F in repairs 15mm dia two way angle valve, cast copper alloy, chromium plated screwed down, high pressure with crutch or butterfly handle complete all as specified and directed.

S&F in repair Jet spray chromium plated with 1mtr heavy PVC hose butterfly type, with chromium plated nuts complete all as specified and directed.

Disconnecting existing PVC water tanks of 500 ltrs capacity, setting aside (or lowering if required) for repairs, cleaning with bleaching powder, etc and hoisting if required reconnecting and refixing in same position as specified and as directed.

Disconnecting existing PVC water tanks of 1000 ltrs capacity, setting aside (or lowering if required) for repairs, cleaning with bleaching powder, etc and hoisting if required reconnecting and refixing in same position as specified and as directed.

S&F GI tube 15 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 15 mm dia & connections complete all as specified and directed.

S&F GI tube 20 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 20 mm dia & connections complete all as specified and directed.

Taking up or down existing GI Tubing 15 mm dia & connections including cleaning for refixing seviceable the same with new fittings and fixed to wall, ceiling or laid in floor and ceiling and wall all as specified and dircted

Taking up or down existing GI Tubing 20 mm dia & connections including cleaning for refixing seviceable the same with new fittings and fixed to wall, ceiling or laid in floor and ceiling and wall all as specified and dircted

S&F rotational moulded polethylene water tank of 500 ltrs capacity, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 500 ltr complete all as specified and directed.

S&F rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 1000 ltr complete all as specified and directed.

S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod and high denty plastic ball screwed for iron pipe and fixed (min wt. 210gms) complete all as specified and directed.

S&F 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair for Amstrong ceiling made out of 600x600x15 mm thick classic lite(RH-95) mineral fibre acoustics ceiling board/tiles with and including powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mm X 600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Grid of modular size 600mmX600mm shall be supported by 6 mm dia G.I. wire for suspending, bolts, necessary washer, nut / clits/ pin hook etc for securing frame work to ceiling to the snap grid complete all as per manufacturer's instruction.

S&F in repair chromium plated curtain rods including CP knobs and brackets complete all as specified and directed.

S&F in repair 600mmx450mm bevelled edges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer complete all as specified and directed.

S&F in repair Aluminium Mortiee lock 4 lever, size 75mm complete all as specified and directed.

S&F in repair door closer aluminium (Die cast) body hydraulically regulated, designation No 3, universal type, suitable foor door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.complete all as specified and directed.

S&F in repair double action floor spring hydraulically regualted made up of minimmum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed

S&F in repair PVC waste pipe of 32/40mm dia complete all as specified and directed.

S&F in repair kitchen sink coupling of any size and any pattern including waste pipe complete all as specified and directed.

S&F in repair bib taps 15mm bore standard of PTMT any colour high pressure screwed for iron pipe and fixed all as specified (minimum wt. 90gms) complete all as specified and directed.

S&F in repairs Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed for iron pipe or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

S&F in repairs angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed both end for iron pipe or brass ferrule for 15 mm bpre of pipe complete all as specified and as directed.

S&F in repairs Stop cock (Concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed both end for iron pipe or or brass ferrule with long shank and cup for 15 mm bpre of pipe complete all as specified and as directed.

S&F in repair swivel shower rose of brass Chromium plated for fixing with 15mm pipe fixed complete all as specified and directed.

S&F in repair vitreous china squatting pan "Orissa" pattern size 580mmx440mm white with integral foot rests excluding flushing cictern and flush pipe all as specified and directed

S & F in Repair 10 ltrs capasity PVC valveless syphonic action type flushing cistern low level white, with inlet ball valve, float and handle including bracket and flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern complete all as specified and as directed.

S&F in repair vitreous china wash basin white, flat, back, size 550x400 mm excluding tap waste but including brackets and including cutting for and pinioning in ends of brackets but exclusive of supply waste pipe all as specified

S&F in repairs 15mm bore pillar tap cast copper allloy with capstan head Chromium plated scwed down with or without letter Hot or Cold with long shank and fly nuts scrwed for iron pipe and fixed as specified and directed.

S&F PVC connection 15mm bore length not less than 300 mm long with both ends PTMT nuts complete all as specified.

S&F in repair 15mm bore angle stop valve of PTMT any colour high prssure screwed for iron pipe and fixed all as specified (minimum wt. 90gms) complete all as specified and directed.

S&F in repair CP towel rail 20mm dia, 600 mm long between flanges complete all as specified and directed.

S&F in repairs brass CP basin mixer for mixing hot & cold water screwed down for iron pipe and fixed of 15mm dia pipe complete all as specified and directed.

S&F in repairs brass chromium plated wall mixer any type and shape with all fittings complete all as specified and directed.

S&F in repairs 75 mm dia PVC (SWR) floor trap plain with greting incl jointing with solvent cement complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall all as specified and directed.

S&F 75 mm bore PVC (SWR) bends complete all as specified and directed.

S&F 110mm bore PVC(SWR) junction single (single T) equal or unequal with access door complete all as specified and directed.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm PVC (SWR) bend any radius complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

Taking down aluminium door shutter and replacement of parts such as rubber beading, glass panes, mortice lock, floor spring, hydraulic door closer and other fittings and refixing in the same opening after replacement of parts complete all as specified and directed.

UTTRAKHAND BUILDERS

M/S WASEEM KHAN CONTRACTOR

M/S CHAUHAN ELECTRIC WORKS

M/S MANSI TRADERS