Formation of Reserve Site Park at Thangammal Nagar 1St Cross in Ward No.19 North Zone.

Clearing light jungle earth, murrains, gravel stoney earth and earth mixed with small size boulders and hard gravel soil etc., complete as per standard specification.

Earth work excavation and depositing on bank with initial lead of 10 meters and initial lift of 2 meters in hard stiff clay, stiff block cotton hard red earth, murrains, gravel stoney earth and earth mixed with small size boulders and hard gravel soil etc., complete as per standard specification.

Plain Cement concrete 1:4:8 [one cement, four M-sand and eight course aggregates] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification.

Supplying and erecting centering to sides and soffits including supports and strutting for drainage sides and culvert body wall sides using 90cm x 60cm and B.G 10stifened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over (silver oak joists ) of size 10cm x 6.50cm spread at about 90cm etc. complete complying with standard specification .

Plain Cement Concrete 1:3:6 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification.

Providing and laying of Rubber Moulded Hydraulic Pressed Paver Block size 63mm thick in uniform shape of approved make to be laid in herring bone pattern with approved non sticking surface in the top and the rate including leveling the base, preparation of sub base with sand cushion 100mm thick, laying out the pavement, cut the pieces to fit the edge, vibrating the pavers, sweeping the sand grouting, providing transporting, loading unloading and laying of paver block as per standard specification

Supply and fixing of slide with Ladder park model using 2Nos of 35mm dia MS.pipe of 14 SWG for standing and sliding, Platform sheet of size 0.45m x 0.90m made of S.S sheet of 16 SWG. Sliding sheet of size 2.40m x 0.45m made of fibre sheet of 14 SWG, and side rails for child to hold while. Climbing is made of 75mm x 25mm thick 14 SWG to a length of 4.50m for both sides. The entire assembly is treated with zinc chromate one coat and enamel paint two coats of three different colours finishing with attractively including all materials and labour charges etc complete.

Supply and fixing of U-model twin sea saw four seater using 65mm dia M.S.pipe of 3mm thick to a length of 4.90m and supported assembly bars using 50mm dia M.S.pipe of 3mm to a length of 2.10 m each for 2 Nos. The four seater of circular type of 250mm dia S.S sheet of 16 SWG. The entire assembly is treated with zinc chromate one coat and enamel paint two coats of three different colours finishing with attractively including all materials and labour charges etc complete.

Supply and Fixing of Two seater swing using 3m long 65mm dia M.S.pipe of 3mm thick. The Slide supports are 3m long 50mm dia M.S pipe of 3mm thick. The 3 way sockets using 3mm M.S.plate and grip the entire unit rigidly. Two swing clamp with ‘U’ and ‘S’ hooks are provided to the swing seat made out of 25 x 25 mm S.S square tube of 14 SWG with stain less steel plates of a grade 304 and size of 500mm x 250mm of 16 SWG and hooks are fitted with 8mm thick tested chain 2 Nos of length 9.80M. The entire assembly is treated with zinc chromate one coat and enamel paint two coats of three different colours finishing with attractively including all materials and labour charges etc complete.

Supply and fixing of ornamental Park benches of size 1.20m x 0.45m each for leg and rest. The seat using 100 mm x 25 mm M.S. rectangular section of 14 SWG and the leg using 50 mm dia M.S.pipe of 3mm. The benches are treated with zinc chromate approved by the Executive engineer before use on work.