SPECIAL REPAIR TO BLDG NOT 31A AND T314BD BATHROOM BLOCK OF 110 MED REGT UNDER GE EAST DELHI CANTT 10

Amount

Taking down cement or cement lime plaster of any description on brick or stone walls and concrete surface of ceiling etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick on fair faces of concrete or concrete surface in ceiling in CM 1:3, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new/old surface decorated brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint etc complete all as specified and directed.

M&L for preparation of new plaster sufaces of walls and applying two coats of oil emulsion distemper over a coat of chalk whiting complete all as specified and directed.

M&L for 3 coats of white wash on ceiling including preparation of newly plastered surfaces, complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement or cement lime morta including all quoins, arches,pillars, etc,

M & L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and directed

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed

S & F Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and directed.

S&F stainless steel butt hinges 100 mm long fixed to PVC door frame complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section of 200 mm length of bolts complete all as specified and directed

S&F extruded aluminium alloy handles fabricated type anodised 100 mm size of handle complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges , steel peg stay complete all as specified and as directed

S & F 3 mm thick sheet glass , ordinary quality and glazed with oil putty in square n. exc 0.5 Sqm in each pane fixed complete all as specified and directed.

Dismantling asbestos cement (corrugated , semi-corrugated , etc ) sheet in any pattern & position of roof coverings.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws with bent to a curve (of any radius as per required) complete all as specified and directed

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour as in ridges hips, vally gutter, drip and straight flashing , fixed with self tapping screws etc complete all as specified and directed

Dismantling unframed work timber scantling in fillets, rails, posts, rafters, purlins, etc under 40 Sq. Cm in section complete all as specified.

Dismantling framed timber scantlings 40 Sq. Cm and over in section , in any position complete all as specified.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240complete all as specified and directed

S&F rolled mild steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250), Quality B, complete all as specified and directed

S&F 20mm dia of neck & 15cm to 30cm long, mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised or embeded in concrete, complete all as specified and directed

S&F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests (excluding flush pipe or flushing cisterns) with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including making good to floor complete all as specified and directed

S & F in repairs PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flush pipe, brackets complete all as specified and directed

S&F in reapir Vitreous China wash basin, white, flat back, size 550 x 400 mm excluding taps , waste , chain and plug but including brackets including cutting for and pinning in ends of brackets or erecting stand including waste coupling 32 mm dia of PTMT (half or full threaded) (minimum weight 32mm - 45 grms/ 40mm-60gms) etc complete all as specified and dirtected by Engr-in-Charge .

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, grating and Union for discharge pipe with grating including automatic flushing cistern complete all as specified.

S & F 32 mm bore bottle traps of PTMT having minimum water seal of 25mm. (Minimum weight 32mm -260 gms/40mm - 270 gms)

S&F rotational moulded polythene, water storage tank 1000Ltrs capacity in double layer , closed top, cylindrical vertical ) hoisted and fixed in position including 20 mm flot ball brass valves high pressure with polythene float and flynut complete, Aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 20mm - 210 gms including dismantling old water tanks and removing to store etc complete all as specified and directed

S&F steel water tubing galvanised 15mm bore medium grade fixed to walls, under floors and on ceiling surfaces and including taking up or down old steel tubing 15 mm bore and connecetions, including fittings etc complete all as specified and directed.

S&F steel water tubing galvanised 20 mm bore medium grade fixed to walls, under floors and on ceiling surfaces and including taking up or down old steel tubing 20 mm bore and connecetions, including fittings etc complete all as specified and directed.

S&F piller tap 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as as specified and directed.

S & F in repairs 15 mm bore bib tap , chromimum plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete all as specifed and directed.

S&F in repair 15mm angle cock/ stop valves, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15mm bore steel tubing complete all as specified & directed.

S & F in repair 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S & F in repair 15 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

Demolition or cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thickness (below or above ground level) complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M & L Coloured Glazed ceramic tiles 350 x 250 x 7mm/ 450 x 350 x 7 mm thick, on vertical surfaces such as skirting, dados etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match. Over 10 mm thick screed in CM 1:3 complete all as specified and directed

M & L Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match laid over 15 mm thick avg screed bed in CM 1:6 complete all as specified and directed

M&L75 mm thick cement concrete type C-2 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and directed.

M & L 25 mm Thick PCC type B-0 1:2:4 (12.5mm graded aggregate) as in flooring, under Tiles and etc all as specified and directed

M & L 75 mm thick Cement concrete work as in plinth protection type C-1 , 1:3:6 (20mm graded aggregates) with finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed

M & L for Chequered cement concrete tiles 30 cm x 30cm x 25mm thick with grey pigment cement and pigments, set , jointed and pointed in neat cement slurry in floor laid over 15 mm thick avg screed bed in CM 1:6 complete all as specified and directed

M&L two coat of synthetic enamel paint (finishing coat) over one coat of red oxcide primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M & L for APP polymaric water proofing membrene minimum 3mm thick and weighting not less than 3.6 kg / sqm of make STP Texsa Ltd /IWL Ltd /MK Petro as approved by GE , black finished reinforced with non woven polyster matt,with fusable finish laid over compatable bitumen primer at the rate of 0.35 Ltr/Sqm torching overlaps with a propane or abutane gas torch, with a over lap of 75 mm at the sides and 100 at the ends and sealing incl applying a coat of cold emulsion bituminous primer all as per manufactur's instructions incl taking down existing treatment with old plaster and preparation of surface and 15 mm thick cement screed in CM 1:4 on roof of concrete surfaces finished even and smooth without using extra cement with mixing of water proofing compound complete all as specified (WPC shall be paid seperately) complete all as specified. Note : the water proofing treatment shall be carried out by the manufacturer or their authorised applicators.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundations etc or for shafts, wells cesspits, manholes, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Returning & filling including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removal of excavated material n.exc 50 mtr and depositing where directed at level not exc 1.5 m above the starting point complete all as specified and directed

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed

M&L Plain cement concrete (1:2:4), type B-2 (using 40 mm graded stone aggregate) as in drains /surface channel complete all as specified and directed .

Demolition and breaking up drain pipes (SGSW/ AC/RCC) including hunching and benching set in cement mortar for 150mmdia pipe, and removal of debris from site and deposited where directed at a distance not exc 1KM from site complete all as specified and as directed.

M & L for 150 mm dia (internal dia) RCC hume pipe class NP -2 laid and jointed complete with colleres complete laid in trenches and tested complete all as specified and as directed.

M& L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipe 150 mm bore incl forming cradles complte all as specified and directed.

Taking down cast iron / PVC soil waste and vent pipes 100/75mm bore of any description with fittings and making good to disturbed complete all as specifed and directed.surfaces.

S&F 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints ,laid on walls complete all as specifed and directed.

S & F 75 mm dia PVC cowls.

S & F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joint laid in trenches or in floor completed all as specified and directed

S& F 110 mm PVC (SWR) junction single (Single T) equal or unequal with access door

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and as directed.

PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in brenching for manholes, bands, coping, bed plate etc with slightly chamfered or rounded angles including necessary from work, if any, and finishing exposed surface even and smooth without using extra cement complete all as specified & directed.

M&L for pre-cast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manholes cover, drain cover and set in cement mortar (1:4) including form work complete all as specified & directed.

S & F Framed work such as in grills, gratings , mainhole cover ,water tank etc and similar work conforming to Fe-290 Gde -E-165complete all as specified.

Supply only liquid water proofing compound complete all as specified & directed.

Taking down carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete with accessories as switches, Sockets, holders,ceiling roses,light fitting regulators etc and removing from site complete for taking credit and making good the disturbed surface of wall/ceiling and matching with the existing surface all as directed.

M&L for point wiring with single core fire retardant low smoke PVC insulated, unsheathed multi stranded copper conductor of size 1.5 sqmm alongwith 1.5 sqmm earth wire of multi strand copper conductor (with same specification) connected to common earth dolly and drawing through & including concealed PVC conduit pipe medium grade( ISI marked) not less than 20 mm dia complete with bends, elbows, reducers etc junction boxes, MS terminal boxes covered with 3 mm thick hylem sheet (top cover) for switches, sockets or fan regulators etc for the following :-

(a) One light point/ fan point/ bell point controlled by one switch

(b) One socket outlet 5 Amps controlled by one switch on same board

Note for item No 2:(i) In case the wiring is encountered with any beam/column,then the wiring will run on PVC casing/caping to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring. In this specified portion wires shall run through the existing conduit or surface new conduit shall be provided as mentioned in note (i) above. (iii) Cutting chases for concealed conduit & making good in cement mortar is deemed included in unit rate.

S&F switch piano flush type, 6 amps one way,SP,230 volts AC all as directed.

S&F socket outlet 6 amps 5 pin , all as specified and directed.

S&F in repair distribution box 4 way , AC, SP & neutral metal enclosure, double door, 240V AC with suitable bus bar, neutral link, earth link suitable for isolator as incomer & MCB, SP as out going all as directed& directed.

S&F MCB C curve,SP,240 volts ,AC, 6 to 32 amps 10 KA.

S&F Isolator, SPN, 240 volts AC, 40 amps.

Supply and fixing in replacement of LED mirror light fitting 10/12 watt, cool/warm white as per site requirement and making all electric connections complete all as directed.

Supply and fixing in replacement of LED tube light fitting, 22 watt. wall mounting type with and including all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable.

S & F in replacement of energy efficicent LED fittings 45W LED 6K five star rating suitable for street/builing area light pressure diecast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed. Note for Srl item No.76 to 78 - Rates for connecting up the luminaire from ceiling rose to connector block with 0.75 sqmm 3 core flexible copper conductor of length not less than 500 mm deemed included in the item rate.

Supply and fixing of security light fitting bracket, 1.0 mtr long made out of galvanized iron pipe of 32 mm dia size light grade complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Taking out old U/s underground cable and S&F PVC insulated armoured XLPE heavy duty U/G aluminium conductor cable served with an inner sheathing of PVC tape armoured with galvanised steel strip wire or tape and overall PVC sheathed of size 6 Sqmm 2 core.

Material and labour for brick protection to cable using old size class 'B' bricks, laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as directed.

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as directed.

M&L of GI pipe medium grade 40 mm dia fixed to wall or laying under path/ road complete all as specifed and directed.

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

M/s Shubh Enterprises

SAGAR ENTERPRISES

Akhil Enterprises

THE LOTUS BUILDTECH