Construction of Veterinary Dispensary at Malanger, Teh. Bangana, Distt. Una (HP)

Amount

Excavation in foundation trenches etc. in all classification of soil such as pick work,jumper work,pick jumper work,blasting work and hard blasting work in dry or saturated condition upto any depth and lift including pumping and bailing out water where required including stacking the serviceable and unserviceable material separately as directed and then returning the stacked soil in 15cm(fifteen centimeter) layers when required into plinth and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus unserviceable excavated earth as directed by the Engineer in charge including entire carriage of material and disposal all surplus excavated/bored out earth within all leads and lifts and other incidentials

Providing form work with steel plates (3.15mm) three point fifteen milimetre thick welded with angle iron in frame (30x30x5mm) ( Thirty x thirty x five milimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc., with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4mtr.(Four metre). (a). Foundations, footings & bases of columns etc., and mass concrete.

(B). Column, pillars, posts and struts. (i). Square, rectangular or polygonal in plan.

(C). Beams, cantilevers, girders and lintels. i. Sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor.

(D).Flat surfaces such as soffits of suspended floors, roofs, landing and the like. ( i). Floors etc., upto 200mm( Two hundred milimetre) in thickness.

(e). Edges of slabs and breaks in floors and walls: Under 20 cm. wide.

Providing and laying cement concrete 1:6:12 (one cement :six sand :twelve graded stone aggregate 40mm nominal size)(Forty milimetre) and curing complete excluding cost of form work in foundation and plinth including carriage of materials upto all leads and lifts.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying cement concrete 1:1.5:3 (One cement : one point five sand :Three graded stone aggregate 20mm nominal size)( Twenty milimetre) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) Foundations, footings, bases of columns and the like and mass concrete.

(b). Columns, pillars, posts and struts in all floor levels.

(c). Suspended floors, roofs, landings and shelves and their support balconies, beams, girders, bressumers and cantilevers in all floor levels.

Providing mild steel/tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all floor levels (a). Tor steel. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Sand) First Class Bricks including carriage of material within all leads and lifts.

Brick work using common burnt clay building bricks in superstructure 1:6 First Class Bricks including carriage of material within all leads and lifts.

Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position complete up to all floor level including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. sal wood/ hard wood

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40mm thick 2nd class deodar wood including entire carriage of materials in all leads and lifts.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.2nd class deodar wood. 40 mm thick

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain grill.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) including entire carriage of materials in all leads and lifts as per the satisfaction of Engineer-in-Charge.

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete. a) 300X16 mm

Providing and fixing anodized aluminium tower bolt (barrel type) anodized transparent or dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. ( a). 250x10mm

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (i) 125mm.( One Hundred Twenty Five milimetre)

(i) 100mm.( One Hundred milimetre)

Half brick work using common burnt clay building bricks in super structure above plinth level upto floor all level using second class building bricks in cement mortar 1:4 (1cement : 4sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer in charge.

6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to three Sand) in all floor level. The rate isincluding carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick 1 in single coat on fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth within all leads, lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand paper and knotting complete Readymixed paint brushing wood primer pink including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Painting two coats(excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter sand papering and stopping. (i) with enamel paint other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters:- With white enamel paint.or other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified sizes laid in floors, treads of steps and landings on a bed of 25 mm average thickness of cement mortar 1:6 (1 cement :6 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete with tiles of White Shade.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

White glazed tiles 6 mm ( six millimetre) thick in skirting risers of steps and dado of size 20×30cm nitco or its equivalent of approved make and size 12mm ( Twelve milimetre) thick cement mortar 1:3 (one cement isto three sand) and jointing with neat cement slurry including carriage of material in all leads and liftrs :-( size thirty centimetre into twenty centimeter) as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying spartic ceremic tiles 5.5mm.thick in flooring (300 x300mm. size)treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground

Finishing with floating coat of neat cement slurry incluidng of material within all leads and lifts.

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished 40 mm thick.

Providing and fixing on wall face PVC(D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqmincluding filling the joints withapproved adhesive complete. 100mm dia pipes

Providing and fixing m.s.holder batclamps of approved design to C.I.or S.C.I pipes embeded in andincluding cement concrete blocks 10x10x10 cm of 1:2:4:mix (1 cement 2sand 4 stone graded stone aggregate20 mm nominal size) and cost ofcutting holes and making good the 100 mm diametre

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers,handles,including applying a priming coat of red lead paint

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing: Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3

Constructing chamber 600mm x 600mmx750mm inside size for fire hydrants with C.I. surface box 350mmx 550mm top and 165 mm deep (inside) with changed lid and RCC top slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 100mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete With 200mm thick walls of brick Masonry in cement mortar 1:5 (1cement :5 sand)

Providing and fixing to wall ceilling and floor galvainised mild steeel tubes(medium grade)tube fittings and clamps including making good the wall including carriage of material within all leads and lifts. (a) 15 mm nominal bore

(b) 20 mm nominal bore.

Making connection of galvainised steel distribution branch with galvainised mild steel main 20mm to 40mm nominal bore by providing and fixing Tee including cutting and threading the pipes complete including carriage of material within all leads and lifts.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm dia.including carriage of material within all leads and lifts.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. Plain bend 110 mm nominal size. including carriage of material within all leads and lifts.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete. 110 mm dia

Providing and fixing pvc cowl 110mm dia including carriage of material within all leads and lifts.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm including carriage of material within all leads and lifts.

Providing and fixing Vitreous china wash down, water closet ( European type W.C pan) Cream shade with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(1 Cement :1 Sand ) ( Seat and over to be measured and paid for separately) including carriage of material within all leads and lifts. Ordinary closet. including carriage of material within all leads and lifts.

Providing and fixing PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.110mm dia including carriage of material within all leads and lifts.

Providing and fixing PVC Coloured / white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material within all leads and lifts.

Providing and fixing GI inlet connection for flush pipe with WC pan including carriage of material within all leads and lifts.

Providing and fixing vitreous china wash basin Cream Shade with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings.Flat back630x450mm including carriage of material within all leads and lifts.

Providing and fixing CP brass waste for wash basin or sink 32 mm dia including carriage of material within all leads and lifts

Providing and fixing 100m sand cast iron grating for gully,foor or Nahani trap including carriage of material within all leads and lifts..

Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screw and washers including carriage of material within all leads and lifts.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden pluges with CP brass screws 600x20mm including carriage of material within all leads and lifts.

Providing and fixing CP brass bib tap with capastan head 15 mm dia. weight should not less than 550 gm including carriage of material within all leads and lifts.

Providing and fixing CP brass pillar tap with capstan head 15 mm dia weight should not less than 550 gm including carriage of material within all leads and lifts.

Providing and fixing CP stop cock 15mm dia including carriage of material within all leads and lifts.

Providing and fixing CP connection pipe with brass unions 30 cms length 15mm nominal size including carriage of material within all leads and lifts.

Providing and fixing brass full way valve with wheel including carriage of material within all leads and lifts. (1) 15mm nominal bore

II) 20mm nominal bore

Providing and fixing GI or MI union including carriage of material within all leads and lifts. (1)15mm nominal size

II) 20mm Nominal size

Providing and fixing charomium plated brass soap dish with C.P.brass brackets fixed to wooden cleats with C.P. brass screws including carriage of material within all leads and lifts..

Providing and fixing laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings Vitreous china 600mm x 450mm x 150mm

Providing and fixing PVC water storage tank double core 1000 ltr net capacity complete in all respect including necessary fittings including carriage of material within all leads and lifts.

Providing and fixing Zet connection complete in all respect 15 mm Dia including carriage of material within all leads and lifts.

Providing and fixing plastic seat ( Solid/ Hollow type) and cover for wash down water closet with C.P brass hinges and rubber buffers including carriage of material within all leads and lifts. White plastic seat and cover.

Providing and Laying of Interlocking Concrete Block Pavements having thickness 60 mm as per drawing and Technical Specification Clause 1504

Providing and laying upto floor two level cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) and curing complete including form work in String courses coping bed plates, anchor blocks plain window sills and the like

Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 1 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete Including cost of form work complete

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. including carriage of material within all leads and lifts.

Steel work welded in built up sections, trusses and framed work,including cutting , hoisting ,fixing in position and applying a priming coat of red lead paint. In gratings framed guard bars, ladders, railling, brackets and similar works.including carriage of material within all leads and lifts.

Bhupinder Kumar

Sandeep Kumar Dhiman

Shiv Kumar

Gagandeep Singh

NATHU RAM