Execution of Miscellaneous Repair Maintenance, upgradation and Construction works in Zone I a cluster of central warehouses located at Mohali, Sirhind, Ropar, Mandi gobindgarh I and II, Chanalo Punjab on Annual rate Contract basis

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineerin- charge.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Single pushfit Coupler

Single tee with door

Single tee without door

Shoe (Plain)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 150 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area2.5 sq.meters and under, including cutting the patch in proper shape,raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 gram per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with:

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).

Providing & fixing expanded metal mesh frame with expanded metal 20x60 mm strands 3.25 mm wide and 1.6 mm thick, and frame made of 25x4 mm M.S. flat sub divided into three equal panels with 25x4 mm M.S. Flat expanded metal to be fixed with 19x3mm M.S. Beading tack welded, 4 nos. of M.S. Cleats of size 50x50x4 mm size with holes for 12 mm dia. bolt i/c and manufacture and priming coat of approved steel primer complete as per drg. No.CWC/PG/414-AC and as per instructions of Engineer- in- charge. The whole frame with expanded metal mesh is to be fixed on the outer side of V4 openings with required size of fasteners 10x80 mm size

Supply of 240V, 1 phase, 250 mm sweep Exhaust fan with 1.5 Sqmm insulated copper conductor wires for connections complete as required.

Supplying & fixing fire buckets

Providing and spreading non-metallic floor hardener minimum @ 4.5kg/sqm in floor concrete (as per manufactures specifications and approved by Engineer-in-charge). Nothing extra shall be payable if manufacturer specifies extra quantity.

Providing and fixing channels for preparing panels of required size and then dewatering of the concrete with vaccum dewatering machine finishing with mechanical trowel with trimix matching (thickness of flooring 75 to 150 mm, along with cutting groove joints at appropriate spacing as per direction of engineer in charge (concrete and steel to be paid separately as per relevent item)

Pluging of roof leakage in AC sheets by a cold applied bituminous caulking compound with mineral fillers in a volatile solvent to retain its plasticity as a selaing material of make shalimar/ sika or equivalnet of good quality . Complete work as per direction of official in charge. Complete compartment roof area to be measured.

Providing and fixing colour coated galvalume profile sheets (Make- TATA/JSW) with the depth of 30 mm and pitch of corrugation 200 mm (Colour and shape of profile as approved by the Engineer-in-charge), 0.60 mm(TCT) total coated thickness( tolerance as per relevant IS code), material yield strength 550 MPa, galvalume AZ-150 GSM (both side inclusive) with regular modified polyester paint and coating of 20-25 micron RMP on exposed surface including primer and 7-10 micron epoxy coating on unexposed surface including primer. The sheet should be supplied in single length as shown in drawing or as desired by engineer in charge and shall be fixed using stainless steel Hex cap headed self drilling/ tapping stainless steel screws M6, 50 mm long with 3 mm thick EPDM seal and Stainless steel stitching screw of size 19X2.5 mm excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. All screw should be sealed with silicon sealant.

Providing and fixing colour coated galvalume sheets roofing accessories (Make- TATA/JSW), 0.60 mm total coated thickness (TCT), material yield strength 550 MPa, galvalume AZ-150 GSM (both side inclusive) with regular modified polester paint and coating of 20-25 micron rmp on expose surface including primer and 7-10 micron epoxy coating on unexposed surface including primer using stainless steel self drilling/ tapping screws of size 6x50 mm with 3 mm thick EPDM seal and Stainless steel plain washer complete : Matching Profile ridge (500 - 600mm).

Complete servicing including Lubricating of old rolling shutters with grease and other suitable lubricating items to make rolling shutter in working condition all work complete as per direction of official in charge

Repair / Refilling gap between roof sheet and walls with cement concrete 1:1.5:3 ( 1 cement: 1.5 Coarse sand (Zone III), 3 graded stone aggregate 20 mm nominal size) and finishing/ leveling with avg 6 mm thick cement plaster both side of mix 1:3 ( 1 cement : 3 fine sand ) to match with existing wall plaster i/c scaffolding and all lead and lift complete as per direction of Engineer -in-charge.(avg thickness of CC 50 mm)

Labour for refixing of dismantled barbed wire or flexible wire rope in fencing.

Plugging of roof leakages in polycoated sheet roof by providing silicon sealant around bolts

Pluging of roof leakage by self adhesive tear resistant (Bituminous sealing tape, used for a wide range of waterproofing work on roofs, building components, caravans ) plugging tape/ Mastic tape of sika multiseal/ shalimar or equivalent of approved make (minimum width 100 mm) after cleaning the dirt/ sheet complete for proper fixing of tape as per direction of official in charge. Rate includes cost of all material and labour required for plugging of roof leakage. complete work as per direction of official in charge

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within: Polycarbonate sheet

Densification & Polishing: Providing Hardening, dust proofing, abrasion Resistant and sealing treatment over concrete Flooring including cleaning & drying the base surface, applying ready to use Euco Diamond Hard Euclide chamical USA/Densi Hard /Master Hard/Lizo c/Concast Densi Hard Cure Hard 24 (Sika India) 2-3 COATS . all as per manufcturer's recommendations and as directed by the engineer . Note:-Polising diamond Grits to be use 60 no, or 100 no (as per floor requirment), then 200 no, 400 no,800 no, 1500 no, and final Polish with 3000 no Diamond Grits for Semi Glossy Look.

Providing asbestos cement 6mm thick corrugated steets roofing and fixing with G.I.J. or L Hooks, bolts and nuts 8mm dia G.I.plan and bitumen washers complete (Excluding cost of purlins,rafters and trusses) corrugated sheets upto 60 pitch. With one and half corrugations overlaps

Supplying & Laying saturated felt type 3 grade-I (Hessain base) on top of AC Ridges with suitable blows type petroleum bitumen of penetration of IS grade 85/25 of approved quality by apply 1.45 Kg. per Sqm. (The hessain type tarfelt should be of approved quality and conform to IS 1322)

Manufacturing/ Providing and laying precast inter locking cement concrete paver blocks of grade M-40 and size 200mm X 100mm X 100 mm including providing and laying 50 to 80mm (avg 65 mm) thick layer of bedding sand, joint filling with fine sand, compacting with plate compactor and final compaction with vibratory roller etc. as per specification. The item includes all cost of paver blocks i.e., cost of ingredients of paver blocks such as sand, aggregate, cement of high strength OPC cement as per IS 8112-2013, cost of bedding as well as sand filled in joints. The rate shall also include all lead, lifts, materials, machine tools, plants, labour, equipment & testing etc. complete in all respects as directed by Enineer - in - Charge

Providing and Fixing at or near ground level precast cement concrete saucer drain of grade M-30

Dismantling & refixing A.C. sheets in roofing with G.I.J. or L hooks bitumen and G.I. plain washers complete as directed by Engineer-in-Charge (A.C. Sheets required for the work shall be used out of dismantled serviceable assets) shall be supplied free of cost.)

Labour for Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply & installation of steel porta cabin of size 12'X4'X8'6'' for toilets with 2 no's of Water closet and wash basins,3 nos exhaust fans, 2 Urinals and accessories for ladies, common and gents washroom with 3 seperate entrances ,cabin with a 75mm x 75mm C-channel base, supported by a 50mm x 50mm square pipe cross member and 25mm x 25mm square pipe. It includes an 18mm fiber cement board and 1mm thick vinyl flooring. The roof, designed in a double-slope hut shape, comprises a 1.2mm MS plain sheet welded to a frame, adorned with 4mm ACP board on the inner side. The cage structure utilizes an MS framework with 50mm thick wall panels, featuring 4mm ACP board on the inner wall and 1.2mm MS sheet on the exterior. Insulation is provided by 50mm thick glass wool, enhancing thermal performance and moisture resistance.

Providing and applying high performance EPU Flooring of JEMKON Make of thickness on concrete surface, which includes surface preparation thoroughly by grinding & cleaning all dirt, debris to achieve a sound surface, followed by a primer coat with Tech 24 of 0.1 MM by mixing base and hardener (as per manufacturer’s specification). It will be followed by a screed coat with Tech 60 of 2 MM by mixing base & hardener & aggregates (as per manufacturer’s specification) followed by a sealer coat and application of Final Top coat with Tech SLE of 0.9 MM by mixing base ,hardener , color paste & aggregates (as per manufacturer’s specification) complete as per specifications and as directed by Engineer-In-Charge. Total thickness will be 3 MM.

Providing and applying high performance PU Concrete Flooring of JEMKON/ sika / equivalnet make of 3mm thick on

RR masonry in superstructure above plinth level and upto floor five level, including leveling up with CC 1:6:12 at window sills, ceiling level and the like - Cement mortar 1:6 (1 cement : 6 coarse sand).

Supplying and laying PVC Pipe

Description of Items

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. A) 25 mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/reccesed steel/PVC conduit as required.

3x1.5 sq.mm

4x1.5 sq.mm

3x2.5 sq.mm

3x4 sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1 mm thick saddle)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable glane plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB /RCCB/Isolator)

8 way double door

12 way double door

Supplying and fixing following rating, 4pole, 415volts, isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required-63A

Supplying and fixing 5A to 32A rating, 240volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and nuetral

triple pole and neutral

Supplying and fixing 3pin, 5amp ceiling rose on the existing junction box/wooden block including connection etc. as required. (Make: Anchor/ Emperor/ Leader)

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Description of Items

Supplying of aluminium conductor PVC insulted, PVC shethed xLPE inner sheathed galvanized strip armoured power cable of 1.1 KV grade conforming to IS:1554(part-1) 1988 or latest amended following sizes etc.

4x16 sqmm

4x35 sqmm

Supplying/Installation/Testing/Commissioning of circular 70 Watt LED Wellglass of following rating in godown with excellent thermal management alongwith IP 66 protection,240 volt, prewired complete with all accesories and suitable hanging arrangement upto 1 metre from the support,connection with 1.5 mm FR PVC insulated copper conductor single core cable and earthing etc. as required a LED Wellglass-40 watt

Supply, installation, testing and commissioning of MV compartmentalized, modular design electrical panel, suitable for 415 V, 3 phase, 50 Hz, 4 wire system, Sheet thickness not less than 2.00 mm for load bearing members and 1.60 mm for doors, with following ratings aluminium bus bars, free standing, totally enclosed, with following incoming and outgoing switches, meters, inter connections with suitable size aluminium cables / bars, complete with terminating arrangements, powder coating the panel, earthing, with cable chamber, busbar chamber, bottom/top cable entry etc., as per below description and in conjunction with technical specifications suitable for incoming and outgoing bus bar trunking/cable termination complete as required. Base supports shall be of size 75x75x8 mm GI MS angle iron duly primered and enamel painted.

Supply, installation,testing and commissioning of following height high mast tower excluding excavation but including the following - a) Supply of stated height high mast shaft in two/three sections suitable for 47 m/sec wind speed, with head frame, winch mounting bracket, luminaires carriage suitbale to install stated number of luminaires in symmetrical arrangement. b) Supply of raising lowering system comprising double drum winch, 6 mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightening finial. c) Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. d) Supply of outdoor stand mounted feeder pillar with 32 A TPN MCB incommer, single dial time switch, 25 A TP Contactor for the automatic switching of luminaires, power tool control with 02 Nos. 9 A contactors and raise lower push button, incomming and outgoing terminals for lights and motor as required. Stand must be double door made up of 2 SWG sheet and powder coated with 7 tank technique. e) Supply of LED Type single dome aviation obstruction light. f) Erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour. g) Installation of the mast feeder pillar by grouting the stand in concrete.

Supply, Installation and commissioning of the trangular shape clamp made of flat steel bar of 5mm thickness, 15mm wide of dimensions of 400mm(L)X 400mm(B)x 566mm(HY) with bolt bolt to install the same on the wall as per the instructions of the Engineer Incharge.

Supply and testing of 20 Watt, 4 feet size, LED Batten, with polycarbonate housing, inbuilt electronic driver, luminance efficacy not less than 100 lm/watt, required CCT as per site suitability/instructions of Engineer-in-charge complete with connections etc. as per the instructions of Engineer-in-charge. (Make : Bajaj, Havells, Phillips, Crompton, or eq.)

Supply and testing of 1200 mm sweep ceiling fan (AC Motor) complete with down rod, capacitor and other accessories, including connections etc. complete as required.

Supply and testing of 300 mm sweep heavy duty exhaust fan with powder coated metal body, BEE Rating not less than 03 star complete with all accessories, connections, etc. complete as required.

CWC/RO_ CHD/Engg./AMC/ZONE-1/26-27/05

Description of Work

Price Schedule: Items mentioned at Sub Schedule ‘A (I)’: • Items based on DSR 2023 for civil works, • Non-Scheduled Market rate Items of Civil work.

CWC/RO_ CHD/Engg./AMC/ZONE-1/26-27/05

Description of Work

Price Schedule: Items mentioned at Sub Schedule ‘A (II)’: • Items based on DSR (E &M) 2025 for Electrical works • Non-Scheduled Market rate Items of E&M work

CWC/RO_ CHD/Engg./AMC/ZONE-1/26-27/05

Description

Total of Sub schedule A (I)

Total of Sub schedule A (II)

Total of all Sub Schedules A(I+II) {In Figures}

Total of all Sub Schedules A(I+II) {In Words}

Description

Name of the Bidder,

Address, Organization ID, Tel./Fax No. & E-mail address of Bidder

Type of constituent (Organization) (Proprietorship / Partnership / Private Limited / Limited)

Attested copy of organization Details (Proprietorship / Partnership / Private Limited / Limited)

Name of the person holding the power of attorney for this Bid

Contact details of person holding the power of attorney Mobile Number Email id.

Attested Copy of Power of Attorney details to sign the Tender Document

Earnest Money Deposit (EMD) of Rs.7,73,700/- : to be paid through NEFT/RTGS in the bank account of CWC, and EMD submission proof is to be submitted. The bank details for submitting the EMD are: - WAREHOUSING CORPORATION, Bank Name – HDFC BANK, Branch Name – HAUZ KHAS NEW DELHI, Account No.- 50100434183210, IFSC – HDFC0000467

Cost of Tender Documents : Free of cost

PF Registration code

GST Registration code

PAN No. of the Bidder

Contractor Registration enlistment with CPWD/ MES/Railway etc if any

Financial Eligibility Criteria:

The Sum (Arithmetic sum) of tenderer’s turnover: revenue (income) from operations for the last three financial year should be of value not less than Rs.870.40 Lakh (225% of Estimated Cost put on Tender). The information shall be supported by audited Balance Sheets and Profit & Loss Statements of specified period. In case Balance Sheet and Statement of Profit/Loss for the immediately preceding financial year have not been prepared / audited; the account for one more preceding financial year can be submitted. In case, Bidder does not submit Audited balance sheet and P&L accounts for a particular year (among previous three years as mentioned above), turn over for that particular year will be considered ‘0’(zero) for calculating arithmetic sum of previous three years. {Please see Eligibility criteria as per Annexure-A in Tender document}

Chartered Accountant’s Certificate for Annual financial turnover/ revenue (income) from operations of specified preceding three years

Annual Financial Turnover/Revenue (Income) from operations (as per P&L Account)

Total Turn Over- RS…….

Total Turn Over- RS…….

Total Turn Over- RS…….

Total Turn Over- RS…….

Experience w.r.t. Similar Nature of Work:

Name of the works completed and presented against the criteria:

Work order/ contract agreement ref number and date

Name of client issuing the work order and completion certificate

Completion certificate -ref number and date

Total value of work completed (Rs.)

Stipulated date of completion

Actual date of completion

Amount / period of delay for which Liquidity damage levied by client (if any)

Work order/ contract agreement ref number and date

Name of client issuing the work order and completion certificate

Completion certificate -ref number and date

Total value of work completed (Rs.)

Stipulated date of completion

Actual date of completion

Amount / period of delay for which Liquidity damage levied by client (if any)

Work order/ contract agreement ref number and date

Name of client issuing the work order and completion certificate

Completion certificate -ref number and date

Total value of work completed (Rs.)

Stipulated date of completion

Actual date of completion

Amount / period of delay for which Liquidity damage levied by client (if any)

Bidder Office in the State

Bidder must have Office, on the latest due date of tender submission in any District of The State where Central warehouse ie site of work, is located i.e. Bidder must have office in State Punjab For this purpose, valid GST number along with copy of rent agreement / property owner ship document shall be considered as proof of office address.

GST Number

Eligibility declaration form as per NIT-clause 3 and ITB-clause 3.2 under form -E of this PQ Performa