Construction of Dialysis Unit in CHC Nalagarh Distt. Solan HP (SH- C/o Building portion and water supply and sanitary installation).

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 meters in width or 10 Per square meter on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 meters including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 meters in all kinds of soil according to the H.P.PWD.specification of 1990 volume-I and sorting out useful & unuseful materials and stacking the same in all leads and lifts and transportation of the unuseful materials for filling in roadways, embankments for grades improvement and leveling to required grades and then disposing of surplus excavated earth in acquired width of road or on approved dumping sites through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and all labour, machineries, materials, tools equipments and safety measures and incidentals nrcessary to complete the work by mechanized means and labour (if any required) .All usefull materials, such as stones,shingles,aggregate and slates shall be sorted along road side to the maximum possible extent in all leads and lifts through all modes of transportation. Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects.

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty x Thirty x Five ) millmetress, so as to give a fair finish including centring,shuttering,strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in foundations,footings,bases of columns etcetra and mass concrete as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty x Thirty x Five ) millmetress, so as to give a fair finish including centring,shuttering,strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in foundations,footings,bases of columns etcetra and mass concrete as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty in to Thirty in to Five ) millmetress, so as to give a fair finish including centring,shuttering,strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in Beams, cantilevers, girders and lintels.Sides and soffits of beams, beam haunching cantilivers, girders, bressumers and lintels upto any depth/height as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty in to Thirty in to Five ) millmetress, so as to give a fair finish including centring, shuttering, strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs , landings and the like up to 200mm thickness as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty in to Thirty in to Five ) millmetress, so as to give a fair finish including centring,shuttering,strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls: Under 20 cm.(twenty centimetres) wide as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges

Providing form work with steel plates 3.15 (Three point One Five ) millmetress thick welded with angle iron in frame 30x30x5 (Thirty in to Thirty in to Five ) millmetress, so as to give a fair finish including centring,shuttering,strutting and propping etcetrawith wooden battens and ballies in all heights of propping and centering below supporting floor to ceiling and removal of the same in-situ-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing as per HP.PWD specification 1990 volume-I, including carriage of all labour equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and laying 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) excluding cost of form work in foundation and plinth, as per H.P.PWD.spesification 1990 volume - I, as per H.P. PWD. spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and laying in position cement concrete 1:1.5:3 (one cement : 1.5 sand : 3 graded stone aggregate) for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability in all works upto plinth level as per direction of Engineer-in-charge.

Providing and laying in position cement concrete 1:1.5:3 (one cement : 1.5 sand : 3 graded stone aggregate) for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability in all works above plinth level up to floor V level as per direction of Engineer-in-charge.

Providing Tor steel /TMT Steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts as per H.P. PWD spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Brick work using first class common burnt clay building bricks in Super-structure above plinth level upto floor two level (Second Class Bricks). in cement mortar 1:6 (one cement :six sand) as per H.P. PWD spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Half brick masonry in 1st class common burnt clay building bricks in in super structure above plinth level upto floor two level in CM 1:4 (one cement :four sand) as per H.P. PWD spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) aluminium work in fixed portion for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per Arch. drawing as per H.P. PWD spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) aluminium work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) as per Arch. drawing as per H.P. PWD spesification 1990 volume - I, including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all incidental charges. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 12 mm ( Twelve millmetres) thick Pre-laminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.

Providing and fixing glazing in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 Per kilogram/ Per square meter) complete as per architectural drawings and directions of engineer- in-charge

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete as per requirement and direction of Engineer in-charge. (Only weight of grill to be measured for payment)

Providing and fixing 35 mm thick shutters wire gauge shutters using Kiln seasoned and chemically treated hollock wood, stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws complete as per requirement and direction of Engineer in-charge

Providing and fixing aluminium 300 x 16 mm (three hundred in to sixteen millmetres) sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing aluminium 250 x 16 mm (two hundred fifty in to sixteen millmetres) sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing aluminium 250 x 10 mm (two hundred fifty in to ten millmetres) tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing aluminium 150 x 10 mm (one hundred fifty in to ten millmetres) tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing aluminium handles 125mm ( one hundred twenty five millmetres ), ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing aluminium handles 100 mm ( one hundred t millmetres ), ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete including carriage of material in all leads and lifts.

Providing and fixing aluminium Single rubber stopper hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including carriage of material in all leads and lifts.

25 mm (twenty five millmetres) thick Kota stone slab floooring 20mm ( twenty millimeter) ( average) thick base of cement mortor 1:4 (one cement : four sand) laid over and jointed with grey cement slury mixed with pigment to match the shade of the slab including rubbing and poilshing complete including carriage of material in all leads and lifts.

Kota stone slab 25mm (twenty five millmetres)thick in riser of step skirting , dado and pillars laid on 12mm (tweleve millmetres) average thick cement mortor 1:3 ( one cement: three sand) and jointed with grey cement slury mixed with pigment to match the shade of slab including rubbing and polishing complete including carriage of material in all leads and lifts.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm (twelve millmetres)thick bed of cement Mortar 1:3 (one cement: three coarse sand) and jointing with grey cement slurry @ 3.3Per kilogram per Per square meter including pointing in white cement mixed with pigment of matching shade complete including carriage of material in all leads and lifts.

Extra for pre finished Eaching to treads of steps of marble stone complete as per the direction of Engineer - in Charge including carriage of materials within all leads and lifts.

Providing and fixing on wall face unplasticised 110 mm ( one hundred ten millimeters) Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( Ten millimeters) gap for thermal expansion, (i) Single socketed pipes including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing unplasticised -PVC pipe clips 110 mm ( one hundred ten millimeters) of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete as required as per the direction of Engineer-in-charge.

Providing and fixing on wall face bend 110 mm ( one hundred ten millimeters) unplasticised - PVC moulded for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing on wall face Shoe (Plain) 110 mm ( one hundred ten millimeters) unplasticised - PVC moulded for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing 0.60 mm (zero point sixty millmetres)thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 ( five) microns primer coating to back coat of polyster of 5 ( five) microns over 5(five)microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of the Engineer-In-Charge.

Providing and fixing ridges or hips 60 cm.( sixty centimetres) overall with 0.45 mm(zero point forty five millmetres) thick prepanted steel sheet with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating 20 ( twenty) micornsover 5 (five) microns primer coating including fixing with prepanted Jor L hooks, bolts and nuts 6 mm. dia with prepanted limpet and rubber washers complete with all accessories as required as per the direction of the Engineer-In-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Steel work welded in built up sections/ framed work in gratings, framed, guards, bars ladders and railing, brackets and similar works including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing,staircase railing and similar works, including applying priming coat of approved steel primer including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Wall painting Two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Finishing walls with textured exterior paint of required shade on new work (Two or more coats applied @ for external plaster are for height upto 3.28 ltr/10 Per square meter) over and including priming coat of exterior primer applied @ 2.20Per kilogram/10 Per square meter including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Finishing with Epoxy paint (two or more coats) on steel work at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications on wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 Per square meter over an under coat of primer applied @0.75 ltr/10 Per square meter of approved brand and manufacture including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

Providing and applying plaster of paris putty of 2 mm ( two millimeters) thickness over plastered surface to prepare the surface even and smooth complete including carriage of all labour equipment and materials to various locations of site through all modes of transportation in all leads lifts and all incidental charges.

6mm (Six millmetres)thick cement plaster to ceiling in cement mortar 1:3 (one cement :three sand) including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges

12mm ( Twelve millmetres)cement plaster in single coat on fair side of brick/concrete walls for internal plastering up to floor two level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm (eighty millmetres) in girth and finished even and smooth in Cement mortar 1:6 (one Cement :six Sand) including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

15 mm (Fifteen millmetres) Cement plaster in two coats,backing coat 15 mm (Fifteen millmetres) and finishing coat 5mm thick on rough side of brick/stone masonry walls for interior plastering upto floor two level mm in girth and finished even and smooth.exceeding 80 rounded angles,chamfers and/or rounded angles not including arrises,internal in cement mortar 1:6 (one cement : six sand) including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Chequerred precast cement concrete tiles 22 mm thick in foot path on 20 mm thick bed of cement mortar (1:4). Using mMedium shade pigment using 50% white cement 50% Grey cement including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing 1216 (16 mm OD) pipe Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge.

Providing and fixing 2025 (25 mm OD) pipe Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge.

Providing and fixing PVC floor trap 110*90 millimeters I.S.I marked of self cleaning design with PVC Pipe complete including cost of cutting and making good the wall and floors as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing 110 mm dia PVC waste and ventlating pipes including filling the joints with approved adhesive complete as per HP.PWD.specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing 75 mm diameter PVC waste and ventlating pipes including filling the joints with approved adhesive complete as per HP.PWD.specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing 100 mm dia PVC Plain Bends ISI marked including fixing with approved adhesive complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental

Providing and fixing 75 mm dia PVC Plain Bends ISI marked including fixing with approved adhesive complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental

Providing and fixing 100 mm dia PVC door Bends of required degree (any radius) with oval access door insertion rubber washer 3 (three) millmetres thick, bolts and nuts complete Supreme fittings and accessories complete as per direction of the Engineer-in-Charge and HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts including all incidental charges.

Providing and fixing 110 mm diameter PVC cowl I.S.I marked including cutting holes in walls and making good the same, as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing 100 mm sand cast Iron grating for gully trap including carriage of all labour equipment and material to various location through all modes of transportation in all leads ifts and all incidental charges .

Providing and fixing 600*450 (Six Hundred in to Four Hundred Fifty) millmetress bevelled edge mirror of superior glass mounted on 6(Six) millmetress thick asbestos sheet or plywood sheet and fixed to wooden plugs with chromium plated brass screws and washers as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges.

Providing and fixing chromium plated brass towel rail I.S.I marked 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms complete with chromium plated brass brackets fixed to wooden plugs with chromium plated brass screws as per HP.PWD specification ,including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing C.P. brass toilet paper holder including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges

Providing and fixing 15 mm nominal bore C.P. brass long Eache bib cock of approved quality conforming to IS standards and weighing not less than 810 gms including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893 115 mm nominal bore including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges

Providing and fixing PVC connection with brass union 45(forty) length 15 (fifteen) millmetress nominal bore , as per HP.PWD specification , including carriage of all labour equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges.

Providing and fixing fullway brass valve with wheel 15 (fifteen) millimeters nominal bore , as per HP.PWD specification , including carriage of all labour equipmentProviding and fixing brass bib cock of approved quality including carriage of all labour equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges.

Providing and fixing square-mouth S.W. gully trap 150 x 100 mm size P type150 x 100 mm size P type class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 Per kilogram and frame to be not less than 2.70 Per kilogram as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of all labour equipment and material to various location through all modes of transportation in all leads, lifts and all incidental charges.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges .

BHAJAN SINGH GOVT CONT

mustak

mangla constructions

RAJ KUMAR