Construction of District Material Testing Lab. at Maitra, District Ramban.

Amount

Earth work in excavation by manual means over areas ( exceeding 30 cm and up to 1.5 mtr in width and 1.5 mtr in depth as well as 10 sqm on plan ) incl. disposal of excavated earth up to 1 mtr from cutting edge, disposed earth to be levelled and neatly dressed in 75 % all kinds of soils and 25 % Ordinary Rock.:- 75% All kinds of Soils

25% Ordinary Rock

Earth work in excavation by manual means in trenches of foundations, drains pipes, cables etc. ( not eXceeding 1.5m in width) and for shafts , wells ,cesspits and the like not exceeding 10 sqm on plan , depth upto 1.5 m including disposal of the excavated earth upto 1m from cutting edge, disposed earth to be levelled and neatly dressed in 75 % all kinds of soils and 25 % Ordinary Rock :- 75% All kinds of Soils

25% Ordinary Rock

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering .All work up to plinth level . 1:5:10 ( 1 cement :5 fine sand :10 graded stone aggregate 40 mm nominal size ) Nallah.including carriage

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work up to plinth level in 1:3:6 mix ( 1 cement :3coarse sand :6 graded stone aggregate 20 mm nominal size) crushed. With 20% Bouldes

Provinding and laying in position, specified grade of Reinforced Cement Concrete. excluding the cost of centering, shuttering, finishing and reiforcement. All work up to plinth level in 1:1.5:3 (1 cement:1.5 coarse sand :3 graded stone agg. 20 mm nominal ) Crushed including carriage

Brick work with common burnt clay F.P S ( non modualar) bricks of class designation 75 in foundation and plinth cement mortar 1:6 (1 cement :6 fine sand including carriage

Extra for brick work in super structure above plinth level lupto floor V level.

Providing and laying Reinforcement cement concrete 1:1.5 :3 (1 cement:1.5 coarse sand :3 graded stone agg. 20 mm nominal ) in suspended floors, balconies, landings, and stair cases having slope upto 15, excluding the cost of centring shuttering, All work up to floor v level.including carriage

Reinforcement for RCC work including straightening,cutting bending, placing in position and binding all complete upto plinth level Thermo Mechanical Treated bars.

Centring and shuttering including strutting propping etc. and removal of form for Foundations, footings, bases of columns etc for mass concrete

Centring and shuttering including strutting propping etc. and removal of form for Lintels, beams , plinth beams, girders, bressumers and cantilevers

Centring and shuttering including strutting propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platforms.

Centring and shuttering including strutting propping etc. and removal of form for Edges of slabs and breaks in floors and walls under 20 cm wide

Providingh cement plaster 12 mm thick cement of mix 1:6 ( 1 cement :6 fine sand ) Including carriage

Providingh cement plaster 15 mm thick cement of mix 1:6 ( 1 cement :6 fine sand ) ncluding carriage

Providing and laying vitrified floor tiles of 600 x 600mm (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to ISI:15622 of approved make in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 Cement:4 coarse sand)including grouting the joints with white cement and matching pigment etc.Complete.

Providing laying and fixing Ceramic glazed floor tiles 300 x 300 mm ( thickness to be specified by the manufactures ) of first qulaity conforming to IS: 13755 of NITCO , ORIENT, SOMANY, KAJARIA or equivlant make in colour shades except White , Ivory , Grey , Fume Red , Brown laid on 20 mm thick bed of Cement Mortar 1:4 ( 1 cement :4 coarse sand ) including pointing the joints with white cement and matching pigment etc. complete.

Providing laying and fixing Ceramic glazed wall tiles 300 x 300 mm ( thickness to be specified by the manufactures ) of first qulaity conforming to IS: 13755 of NITCO , ORIENT, SOMANY, KAJARIA or equivlant make in colour such as White , Ivory , Grey , Fume Red , Brown laid on 12 mm thick bed of Cement Mortar 1:3 ( 1 cement :4 coarse sand ) including pointing the joints with white cement and matching pigment

Providing and fixing pressed steel door frames conforming to IS 4351, manufactured from commerical mild steel of 1.25 mm / 1.60mmthickness including hinges jamb, lock bead and if required angle threshold of mild steel angle of section 50 x 25 mm, or base tiles of 1.25 mm /1.60mm pressed mild steel welded or rigidly fixed together by Machanical means, including M.S pressed butt hinges 2.5 mm thick with mortar guards, lock strike- plate and shock obsorbers as specified and applying a coat of approved steel primer after pre-treament of the surface as directed by Engineer--in -charge. Profile -A. Sheet of 1.25 mm thickness and base tiles of 1.25 mm.

Supplying and fixing rolling shutters of approved make , made of required size M.S leths interlocked together throught their entire length and jointed together at the end by the end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27 .5 cm long wire springs manufacture from high tensile steelwire of adequate strength confirming to IS;4454 part &M.S top cover of req. thickness for rolling shutters 80 x 0.90 mm M.S Laths with 0.90 m thick top cover

Providing and fixing 35 mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked black enamelled M.S . pressedButt hinges bright finishedof req size with necessary screws excluging panelling which will be paid for separately.all complete as per direction of Engineer In Charge. 2nd class kail wood

Providing and fixing panelling or panelling and glazing in pannelled or panna1led & glazed shutters for doors, windows and clerestory windows( Area of opening for panel inserts excluding portion inside groves or rebates to be measured ) panelled or panelled and glazed shutters 25 mm to 40 mm thick. 2nd class kail wood

Providing and fixing glazed shutters 35 mm thick for doors, windows and clerestory windows using 10kg /sqm ( 4mm thick) floatglass panes including ISI marked M.S pressed butt hinges bright finished butt hinges of req. size with necessary screws. 2nd class kail wood

Providing and fixing 35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mmfor doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge

Filling available excavated earth (excluding rock) in trenches plinth, sides of foundation etc. Layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.50 M

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering .All work up to plinth level . 1:4:8 ( 1 cement :4 fine sand :8 graded stone aggregate 40 mm nominal size ) Nallah.including carriage

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade two or more coats on new work

Finishing walls with water proofing cement paint of reuired shade New work( Two or more coats) applied @ 3.84 kg/10 sqm

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade .

Priming with ready mixed pink or grey primer of approved brand and manufacture on wood work ( hard and soft wood)

Providing and fixing M.S grills of required pattern in frames of windows etc with M.S flats, square or round bars etc incl. priming coat with approved steel primer all complete Fixed to steel windows by welding

Chequerred preacast cement concrete tiles 2.2 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles. Including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) Medium shade using 50% white cement and 50% ordinary cement.

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. medium (external work) 20 mm dia. nominal bore

Providing and fixing G.I. pi pes complete with G.I. fittings excluding trenching and refilling etc. medium (external work) 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: 15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: 20 mm dia. nominal bore

Providing and fixing wash Basin with C. I./M.S. brackets, with 15 mm dia tap and all other accessories complete job (660 x460 mm) Hindware, Cera or Jaquar make.

Providing and fixing liquid Soap Container 109 mm wide Hindware, Cera or Jaquar make.

Providing and fixing Towel Ring Hindwear, Cera or Jaquar make.

Providing and fixing mirror of superior Glass (of approved quality) and of required shape and size with plastic .moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 20mm nominal bore

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap

Providing and fixing G. I. inlet connection for flush pipe connecting with W.C. pan

Providing and fixing white vitreous china pedestal type water closet ( European type W.C with seat & lid complete w.c pan with ISI marked white solid plastic seat & lid complete) Hindware, Cera or Jaquar make.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarsesand), inside cement plaster 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement , foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 75

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality Square shape 450mm internal dimensions

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Providing and fixing PTMT Soap dish holder having length of 138mm , breadth 102mm, height of 75mm with concealed fitting arrangements , weighing not less than 106gms.

Providing and fixing PTMT Pillar cock of approved quality and colour 15 mm nominal bore, 107 mm long, weighing not less than 110 gms.

Providing and fixing PTMT Bib cock of approved quality and colour 15 mm nominal bore, 86 mm long, weighing not less than 88 gms (short body)

Providing and fixing PTMT Bib cock of approved quality and colour 15 mm nominal bore, 165 mm long, weighing not less than110 gms (Long body)

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing 4 inch PVC bend

Providing and fixing 4 inch PVC collar

Providing and fixing P Trap

Providing and fixing Flow trap 2/5 inch

Providing and fixing Bend 2/5 inch

Providing and fixing Tee 2/5 inch

Providing and fixing 15 mm dia elbow

Providing and fixing 20 mm dia elbow

Providing and fixing reducer 1/2 inch x 1/4 inch

Providing and fixing socket 1/4 inch

Providing and fixing Tee 3/4 inch x 1/2 inch

Providing and fixing Union 3/4 inch

Providing and fixing Nipple

Providing and fixing Union 1/2 inch

Providing and fixing Bend 2/5 inch

Providing and fixing PVC pipe 4.0 inch dia superior quality

Providing and fixing Bend 2/5 inch

Providing and fixing Tee 2/5 inch

Providing and fixing anodised aluminium Sliding Tower bolt 300 x 16 mm including screwes complete

Providing and fixing anodised aluminiumTower bolt 200 x 10 mm including screwes complete

Providing and fixing anodised aluminiumTower bolt 150 x 10 mm including screwes complete

Providing and fixing anodised aluminium Handles 125 mm including screwes complete

Providing and fixing anodised aluminium Handles 100 mm including screwes complete

Mohd Sharief Wani

M/S AHADULLAH MIR AND SONS

MOHD RAFI SALARIA