Spl Repairs to LT Network System at Med Bty under GE (Utilities) Udhampur

Amount

Excavation in trenches .n exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick, complete all as specified and directed by Engineer-in-Charge.

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed by Engineer-in-Charge.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar / box (KIOSK) out door type, floor mounted, compartmentalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system. dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs, Led lamps RYB for all incomers & outgoings MCCBs are to bus bar spadles to fitted complete base frame of 50x50x6mm angle iron, powder coated, having front and rear openable hinged double door shutters with aprons for cable entry and locking arrangement complete with following, omplete all as specified and directed by Engineer-in-Charge:-

Incoming :- (a) MCCB 315/320 A 4 pole, with thermal adjustable and fixed magnetic setting with extended 50Hz, 415 V with rupturing capacity 35/36 KA-01 No. Make :- L&T, Legrand, Scheineiders, Havells, ABB (b) Bus bar electrolytic grade copper 500 Amp, 4 pole, not less than 1.5 Mtr long SMC insulators mounted on insulators - 01 set Outgoing :- (a) MCCB 200 amps,1 pole, 35/36 KA, with adjustable thermal over load release 50 Hz, 415 volts grade - 01 Nos. Make :- L&T, Legrand, Scheineiders, Havells (b) MCCB 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 125 Amps, with thermal adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T, Legrand, Scheineiders, Havells (c) MCCB 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps, with thermal adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T, Legrand, Scheineiders, Havells

Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level (iii) Outgoing MCCBs shall be fed with solid busbar connectors (iv) Cables shall be terminated using gun metal /SS glands. (v) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) MCCB 315/320 A 4 pole, with thermal adjustable and fixed magnetic setting with extended 50Hz, 415 V with rupturing capacity 35/36 KA-01 No, Make : - L&T, Legrand, Scheineiders, Havells, ABB. (b) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 500 Amp, 4 pole - 01 set Outgoing :- (a) MCCB 160 A 4 pole, with thermal adjustable and fixed magnetic setting with extended 50Hz, 415 V with rupturing capacity 35 KA-02 No, Make :- L&T, Legrand, Scheineiders, Havells,ABB. (b) MCCB 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps, with thermal adjustable and fixed magnetic setting with extended terminals -01 No. Make:- L&T, Legrand, Scheineiders, Havells, ABB.

Note:- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Including suitable thimbles/lugs, nut bolts washers fitted the cables. (v) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming : - (a) MCCB 125 amps, 4 pole, 50Hz, 415 V with rupturing capacity 25 KA-01 No, Make-: L&T, Legrand, Scheineiders, Havells, ABB. Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 200Amp, 4 pole - 01 set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) MCCB 100 amps, 4 pole, 50Hz, 415 V with rupturing capacity 25 KA-01 No, Make:- L&T, Legrand. Scheineiders, Havells, ABB. Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 150Amp, 4 pole - 01 set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) MCCB 63 amps, 4 pole, 50Hz, 415 V with rupturing capacity 25 KA-01 No, Make:- L&T, Legrand. Scheineiders, Havells, ABB. Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 150Amp, 4 pole - 01 set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) MCCB 200 amps, with thermal adjustable and fixed magnetic setting with extended 4 pole, 50Hz .415 V with rupturing capacity 35/36 KA-01 No Make:- L&T, Legrand, Scheineiders, Havells, ABB. Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 300Amp, 4 pole, not less than 75 cm long mounted on insulators 01 set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) MCCB 160 A 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T. Legrand, Scheineiders, Havells Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 240 Amp, 4 pole, not less than 75 cm long mounted on insulators 01 set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

All as per serial item No 4.00 here-in-before but following capacity, complete all as specified and directed by Engineer-in-Charge.

Incoming :- (a) (a) On Load Change over switch 160 A 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -01 No Make:- L&T, Legrand, Scheineiders, Havells Outgoing :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 240 Amp, 4 pole - set. Note :- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) Including suitable thimbles/lugs, nut bolts, washers fitted the cables. (vi) Suitable cable glands for incoming and outgoing LT cable including rate quoted by vendover

S&F LED Street light 60 watt made uppressure diecast aluminum housing with toughned glass and high power leds and secondary lens with IP 66 protection system of efficasy >110 LPW including 10 KV SPD including taking down old UNSV Street lights, complete all as specified and directed by Engineer-in-Charge. Make : CG, Philips or Wipro

S&F in LED flood light with lens 150 watt made uppressure diecast aluminum housing with toughned glass and high power leds and secondary lens with IP 66 protection system of efficasy >110/125 LPW including 10 KV SPD including taking down old UNSV Street lights, complete all as specified and directed by Engineer-in-Charge. Make : CG, Philips or Wipro

S&F in replacement of LED bollard with robust design and efficient garden lights Whistling Oyster/LB12 of 11 watt capacity, 1P65 including earth work, pcc, bends, nut bolt, complete all as specified and directed by Engineer-in-Charge. Make : Wipro LB 12-131-XXX-65-08 or Philips, CG, Bajaj

Gl pipe bracket Suitable size of light single swan neck shape suitable to fix on top of tubular pole complete with clamps, nuts, bolts and washers, complete all as specified and directed by Engineer-in-Charge.

S&F thermoplastic, polystyrene unbreakable junction box size 260 x 210 x 116 mm suitable for pole mounted outdoor type IP 65 insulated complete with Fl clamp & nut, bolts, washers and including phase separator between R, Y, B terminals and one MCB SP 6 amp 10 KA, all duly mounted on din cannel, cable glands for cable entry, complete all as specified and directed by Engineer-in-Charge. Make : Hensel Cat Part No K9350

S&F of Steel tubular swaged poels erected ot truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-31 (9m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the and portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number, with black paint at suitable height, complete all as specified and directed by Engineer-in-Charge. Note: - The earthwork, PCC foundation, steel clamps, MS Cross arms & bracing of angle iron etc will be included deemed to be rate coated for contractor

S&F of Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-ll type 410-SP-31 (12 m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the and portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number, with black paint at suitable height including The earthwork, PCC foundation, deemed to be coated rate by contractor, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of automatic street light control switch of 8 KW three phase using Infrared sensor based Nature Switch for automatic switching of street light. Nature switch operation should be based on Natural Light Lux*level. Reqd illuminance level also have part night operation facility for min 4 hrs to max 12 hrs. The sensor along with suitable rating power contractor (s), one Incoming and three Outgoing MCBs rating of 20-32 Amps & main load circuit wiring (copper) of min 10 sqmm should be enclosed in a pole/wall mountable rust proof, electric shock proof, termite proof and FR grade thermoplastic polycarbonate enclosure conforming to IP66 protection class-2 (Hansel make). The circuit should be also have provision for manual operation (i.e. sensor by pass option), complete all as specified and directed by Engineer-in-Charge. Model No SWADEEP 66-8 KW3P or L&T or Havells

Supply and Laying and fixing in replacement of along the poles or passing through pipes or laid under floor of through walls etc jointing and testing LT Cross Linked Polythene Insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade heavy duty ISI marked with aluminum conductor and overall served with an outer sheath of PVC, of cross sectional area of the following cables as under including taking out old UNSV LT cables, complete all as specified and directed by Engineer-in-Charge :- (Note: Excavation, earthwork, Pipe for cable protection to be measured and paid for separately)

185 sqmm 3.5 core

120 sqmm 3.5 core

95 sqmm 3.5 core

70 Sqmm 3.5 core

50 Sqmm 3.5 core

35 Sqmm 3.5 core

25 Sqmm 3.5 core

16 Sqmm 4 core

10 Sqmm 2 core

Supply &fixing or laying galvanised steel tubing light grade 80 mm dia (ISI marked) for protection of underground cable on poles / walls under road crossing etc of following sizes including dismantling & taking down existing pipe, complete all as specified and directed by Engineer-in-Charge.

M&L for boring / Road cutting of existing road/path for laying of Gl pipe protection for UG cable including making good disturbed area/surface, complete all as specified and directed by Engineer-in-Charge.

Ring suitable for 12 m long pole for semi highmast light and for fixing of six nos flood lights with bolts, nits and screws, ring made out of ERW MS tubing confirming to IS-2713 including drilling of holes of required size for fixing of brackets, painting the exposed surfaces of ring with coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of silver paint on the surface, complete all as specified and directed by Engineer-in-Charge.

M & L for providing earthing with Gl earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 25 x 4 mm thick for earthing lead fixed by means of nuts, bolt, washers etc connected to earth test point complete all as specified in electrical plate NO 3 of SSR1996 part 1, including necessary excavation and earth work in any strata of soil, comman salt, charcoal dust, 40 mm dia light grade GI pipe for protection to earth lead, Gl water pipe 20mm dia with funnel & wire mesh, PCC pit with Cl cover and frame etc, complete all as specified and directed by Engineer-in-Charge. Note:- (i) All the joints shall be made with welding to get proper conductivity. (ii) On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engineer-in-charge

S&F double walled corrugated (DWC) pipe of size 77 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of LT cable in underground, complete all as specified and directed by Engineer-in-Charge. Make : REX/Tirupati Plastomatics Pvt Ltd/ Supreme

S&F double walled corrugated (DWC) pipe of size 50 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II RM for protection of LT cable in underground, complete all as specified and directed by Engineer-in-Charge. Make : REX/Tirupati Plastomatics Pvt Ltd

Material and labour in replacement of PVC insulated multi stranded copper conductor PVC cable sheathed 2.5 sqmm 3 core and making connections of street light fittings and bollards lights, complete all as specified and directed by Engineer-in-Charge.

MOHAN LAL AND SONS (BID ID -3180749)

FANGALIA TRADERS (BID ID -3175188)

EAST URBAN ENGINEERING (BID ID -3182006)