SPL REPAIR TO BLDG NO P-1 (L BLOCK) BATHROOM AND TOILET WK IN GROUND AND IST FLOOR AT OTM ACCN OF ENGR REGT AND PROVN OF IRON SHED 10M (LENGTH) x 9.0 M ( WIDTH) IN TRG AREA UNDER GE (EAST ) FEROZEPUR CANTT

Amount

B/R WORKS Demolition of un-reinforced cement concrete below or above ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar beding (but not backing),removing serviceable tiles to store and rubbish off the premises complete all as specified & directed.

S&F non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in flooring etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with colour of tiles over and including screed bedding 15mm thick in cm(1:6), complete all as specified & directed.

All as per item No 3 here-in-before but as in skirting over and including 10mm thick rendering in cement mortar 1:4 complete all as specified & directed.

M & L Glazed Ceramic coloured tiles 300mm x 200mm x 7 mm thick primium quality on vertical surfaces, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match colour of tiles over and including 10 mm thick rendering in CM 1:4 complete all as specified & directed.

M & L machine cut 20-25mm thick Kota Stone slab (size of slab not less than 550x550mm for flooring and single piece for trades steps including nosing on edge of trades of stair case) laid over and including 20mm thick screed bed in cement mortar 1:6, and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing/grinding and polishing by machine complete all as specified & directed.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

M & L Rendering/plastering, 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces finished even and fair complete all as specified & directed.

M & L Rendering/plastering, 12mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, surfaces finished even and fair complete all as specified & directed.

M & L Rendering/plastering, 5mm thick in cement mortar (1:3) on concrete surfaces, finished even and fair as in ceiling complete all as specified & directed.

M&L for preparation of new plastered wall surfaces and applying two coats of cement base paint complete all as specified & directed.

M & L for preparation of new plastered ceiling surfaces and applying three coats of white wash complete all as specified & directed.

M&L for preparation of new plastered wall surfaces and applying two coats of oil bound distemper complete all as specified & directed.

M & L for preparation of new plastered wall surfaces and applying three coats of white wash complete all as specified & directed.

M & L for complete removal of existing treatment on wall and applying two coats of oil Bound distemper over coat of chalk whiting on plastered surfaces preparatory to distempering complete all as specified and as directed.

M & L for preparation of old plastered ceiling surfaces and applying two coats of white wash complete all as specified & directed.

Complete removal of existing treatment over old surface, preparation of surface and applying two coats of Cement base paint on walls complete all as specified & directed.

Hacking out old broken glass n. exe 1.5 SQM (any thickness size, quality of description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new one complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exc 1.50 Sqm each including cutting holes of appropriate size for insertion blocks of cement concrete for hold fasts complete all as specified & directed.

All as per item No 19 here-in-before but size exceeding 1.5 Sqm & not exceeding 4 Sqm each.

Taking down shutter of any description exe 1 sqm and not exc 2 Sqm complete all as specified & directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates incl lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint incl hinges, hold fasts/lugs etc including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified & directed.

M & L Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorbers, 20mm dia 60mm long MS conduit for housing of a drop bolt, butt hinges, hold fasts/lugs etc and treating of internal surfaces of chowkhats and hold fasts/lugs with a coat of coal tar or black paint including hinges, hold fasts/lugs etccomplete all as specified & directed.

M & L Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in bed blocks of hold fasts, coping etc including necessary form workcomplete all as specified & directed.

S&F 35mm thick, 2nd class hard wood (Hollock), glazed and skelton shutters, open rebated and prepared to receive glass/ gauge etc divided in to squares with plain rounded mitered and rebated sash bars any numbers, fitted with cut and mitered beads for securing glass etc size of members as specified in clause 8.24 (a) of MES Schedule Part-I in Section-8,complete all as specified & directed.

S & F 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 12mm thick BWR glade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.20(a) of MES Schedule Part-I in Section-8 complete all as specified & directed.

M & L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified & directed.

M & L solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site complete all as specified in clause 8 B.2.1 of MES schedule Part-II (2004). complete all as specified & directed.

S & F Pressed handle of mild steel, oval type, 150 mm size, stove enameled black and fixed with steel screws, complete all as specified & directed.

S & F Barrel tower bolts of mild steel, stove enameled black, with bright bolt, 200 mm long and fixed with steel screws complete all as specified & directed.

S & F Sliding door bolts of mild steel, 300mm long, stove enameled black with bright bolt not less than 12mm dia with & including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified & directed.

S&F Factory made box type steel window with side hung shutter including pintol hinges & 2 Nos 150 mm MS tower bolts on each shutter complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified and shown on drg No CEJZ/TD-1019/E8 & CEJZ/TD-1020/ E8.

S&F Factory made box type steel window with side hung shutter including pintol hinges & 2 Nos 150 mm MS tower bolts on each shutter complete without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified , including making good jambs portion by providing plaster in CM 1:4 and finishes as per existing complete all as specified and shown on drg No CEJZ/TD-1019/E8 & CEJZ/TD-1020/ E8.

S & F Mild steel, fixed type ventilaters with side hunge shutters including projecting type hinges with steel handle and steel peg stay, complete with sash bars, dovetailed or welded complete all as specified & directed.

S&F 300 mm Mild steel helical door spring including roller and roller plate complete all as specified & directed.

S & F Plain sheet glass 3mm thick, ordinary quality and glazing, fixed with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified & directed.

S & F Wire cloth galvanised mild steel, 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified & directed.

M & L Painting to new wooden or wood based surfaces of any description, over 10cm width or girth in two coats with synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified & directed.

M & L Painting to new steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & directed.

M & L Painting to new steel surfaces of any description, over 10cm width or girth two coats with synthetic enamel paint including preparation of surfaces complete all as specified & directed.

M& L for Preparation of old decorated surface of steel and iron of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M& L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S & F PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified & directed.

S & F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified & directed.

S & F PTMT handle 125mm long fixed with steel screws complete all as specified & directed.

S&F Water storage tanks 1000 liters capacity rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs including dismantling existing water storage tank complete all as specified & directed.

S & F Ball valve of PVC, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified & directed.

S & F Gun metal Gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified & directed.

S & F Gun metal Gate valve, 15mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union fixed in repairs complete all as specified & directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified & directed.

All as per item No 50 herein before but 20 mm bore tubing.

S & F 15mm bore GI tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified & directed.

All as per item above 52 herein before but 20 mm bore tubing.

S & F in repair stop valve of cast copper alloy chromium plated, 15mm bore, screwed down, high pressure with crutch or butter fly handle, but fancy type, chromium plated with long shank and cup (concelled type) complete all as specified & directed.

S & F Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40 gms) complete all as specified & directed.

S & F Shelf of PTMT fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 300 gms) complete all as specified & directed.

S & F Towel rail 450 mm long of Brass Chromium plated 20 mm dia fixed with & including CP brass screws & wooden/Plastic cleats (min. weight 170 gms) complete all as specified & directed.

Dismantling CI pipe/any type alongwith fittings of 75/100mm dia, below or above ground level, jointed in cement mortar and taking out complete all as specified & directed.

S&F PVC rain water pipes 100mm bore fixed to walls with and including MS clamps complete all as specified & directed.

Dismantling brick tiles laid in single layer jointed & pointed in cement mortar complete all as specified & directed.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof)complete all as specified & directed.

M & L 10mm plaster in CM(1:4) finished even and smooth with using extra cement on bottom layer of batten roof using water proofing compound as per manufacturers instruction or 3% by weight of cement whichever is more (in case of re placement of bottom layer tile) complete all as specified & directed.( Note: WPC shall be measured and separately)

Supply only integral water proofing compound complete all as specified.

M & L for a tack coat of industrial bitumen 85/25 @ 1.50 Kilogram per square metre over a coat of bitumen primer @ 0.30 litre per square metre including preparation of roof surfaces complete all as specified & directed.

M & L 150 micron polythene film including preparation of roof surfaces complete all as specified & directed.

M & L for Mud phuska, 80mm thick average, consolidated thickness, on flat roofs including 25 mm thick mud plaster complete all as specified & directed.

M & L Brick tiles 40mm thick laid on mud mortar (mud phuska) and joints grouted flush in cement mortar (1:3) mixed with 5% of cruide oil by weight of cement and pointed flush complete all as specified & directed.

All as per item No 67 above but except brick tiles complete all as spd and as dirceted .

M &L Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate as in benching, kerbs, mud stop, rounded or chamfered on edges including form work complete all as specified & directed.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified & directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified & directed.

All as per item 71 above here-in-before but using old bricks retrieved from demolition under item above here-in-before including cleaning and removal of mortar from old bricks.

M&L Brick work in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls complete all as specified & directed.

M & L for PCC (1:3:6) type C2 (20mm graded stone aggregate) 50mm thick as in plinth protection complete all as specified & directed.

M & L for 40mm thick PCC (1:2:4) type B1 (20mm graded stone aggregate) as in flooring finishing surface even and smooth complete all as specified & directed.

Demolition of reinforced cement concrete in any position not otherwise specially provided including reinforcement cut as required to facilitate demolition prepare the surface to capting/jointing new including removing rubbish from building and thrown away low laying area complete all as specified & directed.

M & L for formwork to chullah, hooks, chajjas, troughs and similar work including edges for rough finished surface of concrete complete all as specified & directed.

M & L for reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in chajja, supported on walls, beams, roofs, landing, bolconies, canopies and in shelves and like complete all as specified & directed.

M & L TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia and including necessary welding to existing reinforcement where required all as specified and directed.

M & L TMT bars 6 to 8 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia and including necessary welding to existing reinforcement where required all as specified and directed.

M & L for 40 mm thick precast cement concrete (1:2:4) type B0 using 12.5 mm graded stone aggregate as in louvers and jalies (measured solid) including all moulding but excluding frame and set in cement mortar (1:4) including necessary formwork complete all as specified & directed.

M & L Mild steel curtain rod PVC powder coated with fixing side brackets, end cups, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified & directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and getting out complete all as specified and directed.

M & L Hardcore of broken bricks of gauge n. exc 63mm, deposited spread and leveled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in sub base for floors etc complete all as specified and directed.

M &L Cement concrete (1:5:10),type E-2 using 40mm graded stone aggregate in subbase filling and mass concrete complete all as specified & directed.

Returning filling in layers including leveling watering and well ramming in layers n.exc 25 cm thick compelte all as specified and directed.

Removing surplus soil to a distance not exceeding 100 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified & directed.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy braket framing (beam, tee, angle, channel or flat sections) including distance piece, cleat of Fe-290 (Gde E-165) complete all as specified & directed.

S & F Plates (Plain or chequered) channels, Fe 290-W (E-165) square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified & directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu m, getting out, returning, filling in and ramming in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surfaces in Soft/loose soil complete all as specified and directed

M&L Cement Concrete(1:2:4),type B-1 using 20mm graded stone aggregate as in foundation, base of pole etc including necessary formwork complete all as specified & directed.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

E/M WORKS M&L for point wiring with 1.5 Sqmm (nominal area), PVC insulated, FRLS multistranded, single core unsheathed, copper conductor cables drawn through and including PVC conduit with all accessories concealled in wall and fixed to ceiling etc. with and including 1.5 Sqmm (nominal area) PVC insulated, unsheathed,multi stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth dolly including sunken boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light/fan/bell point controlled by one ,one way switch all as specified and directed. (a) One light point / fan point/ Exhaust point controlled by one single pole one way switch. Note;- wiring shall be done in colour coding

All as per item No 94 herein before but One 3 pin socket outlet 5 amps independent board with cable 1.5 Sqmm size

All as per item No 94 herein before One 3 pin socket outlet 5 amps on the same board with other switches with cable 1.5 Sqmm size

All as per item No. 94 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed,stranded copper conductor cable.

S&F Switch piano flush type 6 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

S&F Switch piano flush type 20 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

S&F Socket outlet 2 in 1, 5 pin, 6 Amps, white in colour, duly ISI marked complete all as specified and directed.

S&F Socket outlet, UNI, 2 in one 10 Amps & 20 Amps, white in colour, duly ISI marked complete all as specified and directed.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F rotary Stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, white in colour, duly ISI marked complete all as specified.

S&F Lamp angle holder (Plastic Ring), 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed.

S&F LED bulb of 9 watt, B22, 6500K all as specified and directed.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection complete all as specified and directed.

S&F ceiling fan 1200mm sweep, AC single phase 230 Volts 50Hz, at Bldgs upto 5 mtrs height, including provision of flexible cable 3 core copper conductor of size 23/0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of MES nos with black synthetic enameled paint all as specified and as directed.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 4 way, IP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCBs duly cocealled in wall, factory made, including making good distrubbed surfaces to match with existing surfaces complete all as specified.

S&F MCB SPN, 40 Amps, 240 volts, "B" series, 10KA duly ISI marked, complete all as specified.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, complete all as specified.

M &L for Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft/ loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009) complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, armoured, electric cables (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sqmm 2 core confirming to IS:7098-1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified. (Note:-Excavation & earth work, brick protection, sand cushion shall be measured & paid separately).

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. Note- Punned down thickness shall be measured.

S&F Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified.

manoj and company

S S BUILDERS

Kissan contractor and engg works

Karan Engineers

Chanana Engineers & Contractors

M/s Bansi Lal

M/s Sanjiv Kumar