8122/SAR-69/2022-23

Amount

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified and directed by Engr-in-Charge. Note : Removing of vegetation / shrubs / brushwood / undergrowth and carrying away rubbish to a distance of 50 m deemed to included in quoted rate.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes etc not exc 10Sqm on plan and not exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in each layers not exc 25 cm thick complete all as specified and directed. Note :- Soil obtained from excavation under item 2.00 here-in-before shall be used for filling.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

Material labour for common burnt clay bricks, sub class 'B' grade laid in trenches for protection of UG cables perpendicular to the direction of the cables complete all as specified and as directed by Engr-in-Charge

M&L for sand cushioning to under ground cable provided with layer of sand (8cm deep before laying the cable and 15 cm deep after laying the cable ie total 23 cm and after punning down sand cushioning will be 18 cm complete all as specified and directed by Engineer-in-Charge. Note : 18 cm thick only will be considered for payment purpose.

Labour for angering upto 100 mm bore for road crossing 3 mtr to 20 mtr not exceeding 1.5 mtr in depth for laying of electric cable and GI tubing in soft/loose soil complete all as specified and directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to sides of Pillars, posts, struts piers, columns etc in squarre, rectangular or polygonal, rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to chajjas, chullah hoods, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for cement concreted (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in foundation or mass concreted for fixing of poles or similar works complete all as specified.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in copings and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate), as in sub base all as directed by Engineer-in-charge.

M&L for providing cement concrete in type B0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to (consolidated thickness 65mm or less) as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge.

M&L for for PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in water through, surface channels and drains including necessary formwork, complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes etc. including placing in position and set in CM (1:4) complete all as specified and directed. Note :- Reinforcement shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams,plinth beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded stone aggregate in lintels upto 1.5m clear span, seismic and other similar bands, lintel bands and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item above but 5mm dia and over up to & including 10mm dia in stirrups, spacers & binders.complete all as specified and directed.

M & L brick work sub class 'B' bricks (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work sub class 'B' bricks , (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls including finishing the surface fair and even complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brick work of walls including finishing the surface fair and even complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified. Note : - Supply only water proofing admixture shall be measured and paid for separately.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for 15mm thick plaster over top of roof slab/chajjas in CM 1:4 mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, finished even and smooth without using extra cement all as directed. Note : - Supply only water proofing admixture shall be measured and paid for separately.

Supply only integral liquid water proofing compound (ISI marked).

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles (1st quality), 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for coloured glazed ceramic tiles (1st quality), 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge Note : Glazing/penelling measured and paid saperately in respective items.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed. Note : Glazing/penelling measured and paid saperately in respective items.

S&F factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified and directed.

Supply only 5mm thick Tinted Coloured glass fixed to metal frame complete all as specified and directed.

Supply only 5mm thick Froasted glass in squares n exc 0.5 sq. m each pane all as specified and directed by Engr-in-Charge

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement & directed by Engr-in-Charge.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam sheet instead of wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded prelam PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam both side PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, stile & rails feathered at edges, suppling & fixing in the frame at site as per specification & drawing.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & scrwed complete all as specified and directed

Supply and fixing stainless steel hinges 100mm long medium weight to pressed steel/angle iron frames by welding/screws all as specified.

S&F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked & fixed

S&F extruded aluminium alloy handles 150mm size fabricated type anodised. ISI marked.

S&F 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F Harrison rails,stainless steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F 15mm bore stop / angle valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F 15 mm bore bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed

S&F Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore all as specified

S&F 32mm dia Brass chromium plated bottle traps for wash basins/urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed Complete all as specified

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal with access door complete all as specified.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 100mm, complete all as specified and as directed.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including making good to distrubed surfaces of floor to match with existing sorroundings complete all as specified.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white (ISI marked) of 10 litre capacity with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or 32 mm dia PVC pipe, for low level cistern connections to pipes and fixing of chain and pull, or lever, if any complete all as specified..

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including cutting for and pinning in ends of brackets or erecting stand, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed complete all as specified.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed to wall complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

M & L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered / asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1mm thick wall care putty of approved tint complete all as specified & directed by Engr-in-Charge.

Material and labour for preparation of new plastered surfaces and applying two coat exterior emulsion paint over a coat of primer paint complete all as specified and as directed any tint. Note: The Camouflaging Pattern decided by Engr-in-Charge

M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) type D2 (using 40 mm graded stone aggregate)

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars complete all as specified and directed.

M&L for mild steel Round bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150mm bore pipe complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

Dismanteling steel poles/ strut of any size any type complete all as specified and direcetd.

Dismanteling cross arms of MS Channel or angle section etc complete all as specified and directed by Engr-in-charge.

Dismanteling insulator any type any size complete all as specified and directed.

Dismanteling of ACSR or AAC conductor complete all as specified and as directed.

Demolition brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismentling floor , hearth or wall tiling incl cement mortar bedding (but ot backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of reinforced roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Dismantling unframed work timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

Taking down chowkats or frames with shutters not exc. 1.5 Sqm complete all as specified and as directed.

Taking down chowkats or frames with shutters exc 1.5 Sq mtr but not exc. 4 Sqm complete all as specified and as directed.

Taking down Old bib tap, stop cock, piiler cock, & ball valve of CP complete all as specified and as directed.

Taking down Old Unserviceable flush cistern complete all as specified and as directed.

Taking down Old Unserviceable PVC pipe any size complete all as specified and as directed.

Taking down Old PVC Water tank of capacity 500 Ltr with float valve complete all as specified and as directed.

Providing and laying for Precast steel fibre Reinforced concrete RCC Soak Well Ring and size of ring 1200mm dia , 600mm height , ring wall 75mm thick complying to the standard specifications as mentioned in the IS 12592 BIS Standard circular shape complete all as specified and directed by Engr-in-Charge.

Providing and laying 100mm thick for precast SFRC drain cover without frame but including complete sides iron sheets (medium ) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton /Sqm in square or rectangular shape complete all as specified and directed by Engr-in-Charge.

Supplying, laying, jointing, testing and commissioning under ground XLPE LT electric cable 1100 Volts grade, heavy duty, PVC insulated and sheathed armoued electric power cable with stranded aluminium conductor, of cross sectional area 50 Sqmm 4 core conforming to IS- 7098 (Part I) 1988 as in trenches over brick and sand cushioning or along the wall/pole through pipe etc served with an inner sheathing of PVC tape and overall PVC sheathed armoured with galvanized steel wire or tape complete all as specified and as directed.

Supplying, laying, jointing, testing and commissioning under ground XLPE LT electric cable 1100 Volts grade, heavy duty, PVC insulated and sheathed armoued electric power cable with stranded aluminium conductor, of cross sectional area 120 Sqmm 3.5 core conforming to IS- 7098 (Part I) 1988 as in trenches over brick and sand cushioning or along the wall/pole through pipe etc served with an inner sheathing of PVC tape and overall PVC sheathed armoured with galvanized steel wire or tape complete all as specified and as directed. Note for item Srl No 112 & 113 :- Earth work, sand cushioning & brick protection shall be measured and paid saperately under respective item of Schedule.

M&L for precast concrete cover class HV type 1, flat size 300mmx180mmx40mm laid in trenches for cable protection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing GI stay wire of 7/3.15 SWG upto required length complete all as specified and directed .

Supply and fixing mild steel galvanised stay assembly set complete comprising of 16mm dia , 400mm long stay bow, 2150mm long stay rod 20mm dia , 300mm x 300mm x6mm stay plate thimble , all as shown in electrical plate no.1 of MES Schedule part-1 2010 complete all as specified and directed.

S&F Loop type insulator, vitreous porcelain, white, brown or green small size, with overall dimensions 65 x 90mm, clearance of hole 16m complete all as specified and as directed.

S&F cross arms, bracings, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending (cold or hot) drilling holes for bolts bent to any shape or size as indicated or directed inclusive of one primer coat of red oxide zinc chromate one under coat and one finishing coat of aluminium paint complete all as specified and as directed.

Supplying, laying, jointing, testing and commissioning under ground XLPE LT electric cable 1100 Volts grade, heavy duty, PVC insulated and sheathed armoued electric power cable with stranded aluminium conductor, of cross sectional area 10 Sqmm 2 core conforming to IS- 7098 (Part I) 1988 as in trenches over brick and sand cushioning or along the wall/pole through pipe etc served with an inner sheathing of PVC tape and overall PVC sheathed armoured with galvanized steel wire or tape complete all as specified and as directed.

M&L for taking out old unsv HT Cables of any size from any type of soil strata by any means complete all as specified and directed by Engr-in-charge.

M&L for cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 11000 volts grade of size 3 core 95 Sqmm (E) conforming to IS 7098 (Part-II) laid in trenche/crossing the road/fixed on pole, testing, commissioning complete all as specified and direceted Engr-n-charge.(Note:- Exacavation & cable protection work shall be measured and paid saperately under respective items.)

Supply, installing, test & commisioning outdoor type feeder pillar box suitable for 11 kv, made out of 3.15 mm MS sheet, powder coated, dust and vermin proof with rain water protection, double door type with locking arrangements of size 1.2m x 1.2m x 0.6m (Min) with provision of HT 11 KV post insulators, 3 Nos. fixed inside with suitable size of copper bus bars for cable connections and danger notice plate, panel to be fixed at 45 cm above ground level on brick masonry plateform including 75 mm thick PCC (1:3:6), type C1 (using 20 mm graded stone aggregates) around the area upto 1.5 Mtr in all directions from the panel, cable joints inside the panel provided with suitable insulators and copper bus bars all as directed including provision of fencing as per existing pattern with openable gate (approx area 20 Sq mtr), height upto 1.5 mtr complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to GI strip 25mm X 4 mm main earthing lead by means of galvanized bolts, nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I (2009) connected from plate to panel & including adequate quantity of charcoal dust and common salt all around earth plate, PCC (1:3:6) type C-1 (using 20mm graded black trap/granite/Basalt stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded black trap/granite/Basalt stone aggregate) 40mm thick cover reinforced with 8mm dia TMT bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 20 mm dia with funnel and wire mesh, and 40 mm dia GI medium grade earth lead protection pipe, complete all as specified and directed.

Supplying, fixing, connecting, testing and commissioning cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm complete all as specified and as directed.

Supply and fixing 120 watt LED Flood Light fitting with not less than 100 lumen / watt delivered lumen efficacy , cast aluminium alloy housing IP 66 protection, input voltage range 140-270 volts, auto cut off at voltage exceeding 300 volts, auto power on after cut off with time delay of less than 60 seconds, power factor more than 0.95, surge protection 4 KV internal and 10 KV external, driver current not exceeding 700 mA, driver electrical efficiency not less than 85 % at constant current delivery, with secondary optic lense for energy LED, having name of manufacturer and logo embossed on housing of each light fitting, LED CCT 5700 + 300 ANSI BIN, having PVC FRSR insulated copper cable of 3x2.5 Sqmm all as specified and directed.

S & F sub main wiring with PVC insulated, fire retardant (FRLS), unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 2.5 sqmm (Nominal area) drawn into new conduit medium grade, 25 mm bore having 2 mm wall thickness and including one run of 2.5sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 2.5 sqmm cable and one run of 2.5 sqmm cable of earth continuity conductor in conduit shall be a unit length. (ii) New conduit & accessories deemed to be included in quoted rate.

Supply and fixing High beam revolving search light LED type of capacity 150 Watt, focus range not less than 400 mtr , IP66,high lumen led >140lm/w, PF>0.95, CCT 5000K-6500K,CRI>70 optical grade PMMA/PC lens reflector, efficiency>95% narrow beam 7 degree , die cast LM6 body with air fins, constant current, average lux (in 500 mm circle) at 10 meter away 2500 to 6000 ( as per model) , working volt 100V to 300 V, protection from short circuit , over load, low/high volt, working temp -20 deg to 60 deg celcius meet LM 79, LM 80 , IS:10322 with manual operated tripod stand made of iron & steel , suitable for mounting of search light in such a way that search light can be rotate one full round arounds its verticle axis and could be locked at any position. Additionaly having PVC castor wheel at bottom for easy movement on plattform with wheel locking arrangement . standard height of tri pod stand is 1 mtr above the stand complete all as specified and directed by Engr-in-charge.

Supply and laying 90/76 mm outer dia/ inner dia, double walled, corrugated DWC duct pipe conforming to IS- 14930 Pt-II with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed.

Supply & fix cable root indicator made of mild steel plate of size 200 mm x 200 mm x 6 mm thick fixed/welded on angle iron of size 25mm x 4mm, 600mm long , duly painted with one coat of primer of zinc oxide paint and finished with two coats of synthetic enamel paint and writing of cable details as directed by Engineer-in-charge, grouted in PCC 1:3:6 type C-1 using 20 mm graded mechanically crushed stone aggregates block of size 150mm x150mm x150mm in foundation including necessary form work complete all specified and directed. Note : - PCC & frame work is deemed to be included in quoted rates.

M & L for concealed point wiring complete with PVC insulated and unsheathed FRLS cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia, with MS terminal boxes (not less than 1.6 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified and directed for the followings :- One light / fan/exhaust point/bell point controlled by one way switch

All as above item No. 130 but One 5 Amp socket outlet on independent board.

All as above item No. 130 but One 5 Amp socket outlet on same board.

All as per above item No-130 here in before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, FRLS cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified and as directed.

S&F switch piano type 5 amp one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F switch piano type15 Amps one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 3 pin 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 2-in-1, 3 pin 5 amp and 15 amps all as specified and directed.

S & F Lamp holder bakalite type with back plate suitable for batten fittings complete all as specified as directed

S&F ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & directed by Engineer-in-Charge.

S & F of sub main wiring with PVC insulated, fire retardant (FRLS), unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn into new conduit of any size and type / casing-caping with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) New conduit/ casing- caping and accessories deemend to be included in quoted rate. (ii) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor shall be a unit length.

S&F of sheet metal enclosure double door suitable for SPN distribution boards when MCBs to be used having 200Amp rated bus bar 6 ways 240 V complete all as specified and as directed.

S&F MCB SP 5 to 32 Amps, 240 volts curve 'B',breaking capacity 10KA, all as specified.

S&F MCB SPN 16 to 40 Amps, 240 volts, curve 'B', breaking capacity 10 KA, all as specified.

Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth lead 4.0 sqmm galvanised iron wire by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead shall be protected by GI pipe 15 mm dia medium grade and connected to distribution board including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and as directed.

S&F 9 watt three star rating LED bulb with B22 Base cap, 950 lumens ,Colour rating Index 80,colour temp F 6500K,satrtup time less than 2 sec,In built surge 3.0 kV, voltage range 140V to 270 V , Lamp life 15000 hours complete all as specified and directed.

Supply and fixing Exhaust Fan , steel body AC single phase ,230 V of size 300 mm sweep heavy duty with, blades , frame and louvers with all fixing element complete all as specified and directed by Engr-in-charge

Supply and fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed by engr-in-charge.

Supply and fix electric water heater, storage type ABS body with steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Supply and fixing wall mounting fan 230 volts single phase oscillating 400 mm sweep suitable for wall mounting including all fixing accessories complete all as specified and directed .

M&L for bell push large flush type 5 Amp one way 240 volts AC complete all as specified and directed.

M&L for bell ding dong / bell musical single phase 230 Volts all as per specified and directed.

M&L for taking out cable of size upto 6 Sqmm from trench with proper safety arrangement and keeping for re-use complete all as specified and directed by Engr-in-charge.

M&L for Relaying cable of size upto 6 Sqmm with proper safety arrangement and cable protection element complete all as specified and directed by Engr-in-charge.Note:- Cable protecton element will be measured and paid saperately. NOTES:-(1)The entire work of exacavation and taking out of cable / relaying of cable to be executed under supervision of rep of SE(L) . (2).MES is not responsible for any damage to cable during exacavation /taking out/relaying.

Supply and fix Gun-metal. globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm bore all as specified and directed.

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 40mm bore all as specified and directed.

Supply and fix forged brass swing type check valve PN 1.6, screwed both ends for iron pipe and fixed of size 20mm bore all as specified and directed.

Supply and fix forged brass swing type check valve PN 1.6, screwed both ends for iron pipe and fixed of size 40mm bore all as specified and directed

Supply and laying in trenches/fixing to wall etc of GI tubing "Medium grade". (ISI) marked, including all fittings i.e. unions, sockets, bends, nipples etc of size 20 mm dia complete all as specified and directed

Supply and laying in trenches/fixing to wall etc of GI tubing "Medium grade" (ISI) marked, including all fittings ie. unions, sockets, bends, nipples etc of size 40 mm dia complete all as specified and directed

Factory made mild steel common header made out of 6 mm thick sheet having following specification (1) Internal Dia 80 mm. (ii) I shape having total length 1.5 mtr. Provided with 3 branch connections. one branch connection of 20 mm dia (outlet), one of 40 mm (outlet) and one of 32 mm dia (inlet). Each branch connection upto 150 mm long and are made out of 6 mm thick MS sheet. Welding of flange shall be part of job. (iv) Header shall have epoxy powder coating from inside and provided with 2 coats of synthetic enameled over one coat of red oxide primer.

M&L for Boring/Drilling bore well of 125 mm dia for Casing strainer pipe all as specified and directed.

Development of bore well with compressed air and then with 25 % extra capacity pump by pumping muddy water complete all as specified and directed

Supplying. Assembling, lowering and fixing in Vertical position in bore well unplasticized PVC medium well casing pipe of size 100mm dia all as specified and directed

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen of size 100mm dia all as specified and directed

Supply and fix bail plug/Bottom pug of size 100mm dia all as specified and directed

Material and labour for pea gravels 3 to 6mm in size filling in bore well opening after lowering of PVC column pipe all as specified and directed by Engr in charge

Supply and fix M.S clamp of 100mm dia to the top of Casing pipe all as per specified and directed

Supply and fixing of suitable six threaded mild steel cap all as specified and directed

Supply, lowering, testing and comissioning of submersible pumpset having discharge not less than 100 LPM at an minimum head of 39 mtrs capcity to run on 230 volts, single phase, 50 Hz cycle complete all as specified and directed by engr in charge

Supply and Install of Starter panel suitable for submersible pumpset above at Ser No 170 complete all as specified and directed

Supply and fix submersible cable of size 4 sqmm 3 core, flat, multistranded copper conductor, PVC sheathed cable 1100 volts grade suitable for submersible pumpset complete all as specified and directed.

Supply and fixing of Heavy duty PVC column pipe 32mm dia in size suitable for borewell complete all as specified and directed

Supply and fix angle iron, supports, clamp and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts in any shape or size as per site requirement complete all as specified and directed by Engr in charge

Gupta Enterprises

RADHA ENTERPRISES

BRIJ CONSTRUCTIONS