Development of Roundabout of Sahjanand Chowk Hardscape and Softscape work

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. CONCRETE PAVER, POLISHED GRANITE, ROUGH FINISH GRANITE & SAND STONE

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). CONCRETE PAVER, ROUGH FINISH GRANITE & SAND STONE

Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I. PAVED AREA OF ROUND ABOUT

Providing designation 75B brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. AT EDGE OF STONE FLOORING & STEPS

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with : Cement mortar 1:6 (1 cement : 6 coarse sand) SEAT WALL

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand ) : 8 graded stone aggregate 40 mm nominal size ) AREA OF PVAED AREA ROUND ABOUT

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. CONCRETE PAVER

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting In position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. KERB

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level, Water feature base & water feature wall

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete Water feature base & water feature wall

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: Outer Ring wall, retaining wall base, Inner Ring wall & Inner Ring base

Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. Outer Ring wall, retaining wall base, Inner Ring wall & Inner Ring base

Providing TMT steel reinforcement as per approved design & drawing.Steel Reinforcement @80kg / cum for RCC & Steel Reinforcement @160kg / cum for retaining wall

Providing 12mm thick cement plaster (1:6) with with clean coarse sand of F.M. 1.5 and including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I . landscape wall

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) for Eg. Total quantiy External Plaster

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. White sand stone

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. ROUGH FINISH GRANITE

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge: GLASS MOSAIC TILE

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade POLISHED GRANITE

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works MS JAALI BELOW PEBBLE STONE '@ 25 KG PER SQM

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work MS JAALI BELOW PEBBLE STONE

Providing & fixing of White River (Stone Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. PEBBLE STONE

Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : Red sand stone Moulding at outer periphery & Moulding at Inner periphery

Extra for stone work ashlar sunk or moulded in cornices

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) Area of Existing round about

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Area of Existing round about

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in: Channels, angles, tees and flats

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.3 Screened through sieve of I.S. designation 4.75 mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 90 cm dia, and 90 cm deep

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.

Providing and stacking of Tabernaemontana coronaria (Chandni single) of height 75-90 cm. with 5-6 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma stans of height 90-105 cm. bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and displaying of Areca Palm having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Dracaena song of India specimen (three in one), having ht. 60 cm & above, well developed, fresh and healthy with good foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Raphes palm having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Acalypha twisted well developed with fresh & healthy 30 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Spider Lily (Hymenocallis littoralis) in polybags

Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge

Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Column light made of mild steel with fine laser cut design and predefine logo closed by diffuser and have ingress protection for optical compartment. Fitting height 2.5 mtr above ground level with mid light illumination of 40W. The column section shall be of 500mmx500mm with top part predesigned LOGO with two street light of 50W for illuminating the side areas. Mid-section gives the homogeneous light output. All pole section Shall be welded by certified welders using high MIG welding process. The Service door shall be provided at bottom part of the pole which equipped with a C clamp with sliding nuts to accommodate a built in connection box. The control gear tray is prewired with MCB, terminal connectors for loop in loop out arrangement. The base plate of the pole is design with elongated foundation holes for fine alignment of the pole during installation. Fitting is made of mild steel with fine laser cut design and signage closed by PMMA diffuser tailored with lighting to suit your specific needs as per detail drawing. Color tolerance ,3 SCDM to avoid color deviation. All exterior parts are made of stainless steel. Diffused symmetric light without glare. Light output of source is more than 110lm/ watt, CRI>70, Surge protection 10k, operating voltage 140-270V, wired with Branded LEDs of Osram/Cree or equivalent and Fulham or equivalent constant voltage/current driver with efficiency>80%, power factor>0.9, THD<=10%. The CCT of led will be 3000k/4000k/5700k as required by the project. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Column light fixture is complete in all aspects with all accessories except foundation bolt.

Spike light for building/Tree facade. Fixture to be made of MS alloy in 10W LED engine with a beam of 36 degree to give a specified coverage to lit. The diffuser is toughened Clear glass of 6mm thickness with optical reflector to reduce glare controlled, Silicone clear gasket, SS fasteners. This luminaire contains built-in LED modules. Lifespan of the luminaire > 60,000 hours at 40°C. Driver efficiency >80%, power factor >0.90, Operating temp. -15°C to +50°C.THD <15%,

Bollard light made of GI sheet and have Ingress Protection of IP66 for optical compartment. The decorative Bollard shall be of height 1mtr above ground level with LED of 20W for area illumination and Bollard with top predesigned NOIDA LOGO laser cut to illuminate the surroundings with noticeable mode. The Bollard light section of 350mmx350mm x 3mm thickness up to 1mtr long with four side illuminated portion. Bollard is made of GI sheet with fine laser cut design tailored with lighting to suit your specific needs as per detail drawing. Luminaire primarily coated with epoxy resin and top coated with powder coat. All exterior parts are made of stainless steel. Light output of source is more than 110lm/ watt, CRI>70, Surge protection 4k, operating voltage 140-270V, wired with Branded LEDs of Osram/ Cree and Fulham or equivalent constant voltage/current driver with efficiency>85%, power factor>0.9, THD<=10%. The CCT of led will be 3000/4000/5000 as required by the project. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is complete in all aspects with all accessories except foundation bolt.

UNDER WATER / WATER BODY LIGHTS Underwater LED focus light with 18 LEDs/fixture. 10MM tempered glass, color temperature options, high grade stainless steel. Underwater lights surface mounted for waterbody applications, to highlight the water body . The fixtures are of high grade stainless steel 316 material, suitable for places near salt-water. NICHIA and CREE LED source is used in underwater lights. The lifespan for the fixtures is above 50,000Hrs. With 24VDC the lumen output is high. A narrow and wide beam optics are standard options to chose. Color temperature options for underwater lights is 2000K, 3000K and 6000K. RGB and RGBW is also possible with DMX control system. These lights come with 18 LEDs/fixture & 10MM glass.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. - 3 x 1.5 SQMM ( make : Polycab/ KEI/ RR Kabel)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Incoming cable for the feeder pillar Supplying & Laying of Following sizes 1100 volt grade XLPE insulated PVC sheathed aluminium conductor armoured cables as per specification in existing trenches/pipes, cable trays, ducts, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning as Required. - 3-1/2 CORE 50 Sqmm

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.15 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I. 25 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I. 32 mm dia

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I. 125 mm thick wall

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I. 250 mm thick wall

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges - Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark) Pillar cock

Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges - Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark) Angular Stopcock /2 way bib cock

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door - 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door - 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. From 0.00 M to 50.00 M below G.L.

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. From 51.0 M to125.00 M

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. From126.0 M to175.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

ARTISTIC SCULPTURE DEPICTING TRIBALS, FREEDOM FIGHTERS/LEADER, TRIBAL ART WITH SCULPTURE\ AND EXTERNAL CONCEPT Creation - 4 MTRX 3 MTRX 3 MTR Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork Execution:Execution of approved design in ss 316 grade steel / stone/casted alluminum pu colored antique as per approved finish (mrf/akzo nobel) and protected against discoloration by sealing it with top coat of Mrf/Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing & Staad file etc., to withstand high wind pressure. The sculpture will be free from any Undulation/Dent unless it is part of the design. The cost is inclusive of transport/packing and installation of the same at site. Fastener/screws hilti or equivalent company. Approved Make - East Craft Designs Pvt. Ltd., New Delhi or equivalent artist with relevant experience

Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade. 2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads. 3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (2 nos) screw fitted with M.S structure vertically &amp; horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm , frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole. 4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge 900 mm (W) x 1200 mm (H) Approx (2400 mm post height)

WATER FEATURE FOAM JET Supplying, Installing, Testing & Commissioning of Water Fountain System , As per the specifications : Jet nozzle 4 set of supremepools.submersible water proof light made out of Noryl / stretched stainless steel and cable gland suitable to be fitted with emitter type power with all in one symmetrical optical lens of 85% effeciency step tempered glass 8mm with protection class of IP-68 i/c connection & water proof jointing etc as required 4 set of supremepools,.Indoor type Cubical Control Panel made of 16 gauge CRC sheet powder coated with 4 Starter of supremepools, Single phase preventer, MCB, volt-meter, Amp meter, TP MCB's, for switching on and off pumps and lights, Protection circuits etc with reputed makes L& T, Schneider . ,Complete with relays 4nos, of supremepools.Step Down/Power Supply Transformer For the Light 8 nos of supremepools ,.Enclosure Box For the Light 4 sets,. SS Light Stand 1 sets,.Recirculation submersible pump to acheive the design flow with proper head and discharge 4 nos, of supremepools.Capital fitting in uPVC such as control valves NRV's etc. required for the final installations 4 job,.Supply, installation, testing & commissioning of uPVC pressure Pipes with plain socket suitable for solvent cement jointing conforming to IS:4985/2000 & fittings conforming to IS 7834/87 including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs including necessary 1 job,. Complete Electrical Work such as conduits, bends, fittings etc. of required sizes 1 job,.Wires of Various sizes including accessories like glands, stickers, sub tape etc for final equipment installation 1 job,. of supremepools Providing MEP Shop drawings For the WF with all nozzles in details 1 job,. Installing, Tasting & Commissioning of the Water Feature equipments 1 job

Agra Red Sandstone Jali, smooth finish, H/Thick: Per SQF x 35 to 40 M/M/ Cm.

Agra Red Sandstone Pillar, smooth finish, H/Thick: 120" Inch, Diameter: 16" Inch, Weight: 329 Kg.

Beige Sandstone Sculpture, smooth finish, H/Thick: 52" Inch, Weight: 1142 Kg.

Kandla Grey Sandstone Bollards, smooth finish, W: 8" Inch, L: 8" Inch, H/Thick: 27" Inch.

Kandla Grey Sandstone Carved Bench, W: 60" Inch, L: 16" Inch, H/Thick: 18" Inch, Weight: 210 Kg.

Rajasthan Black Granite Ball Shape Bollards, Honed Finish, Diameter: 16" Cm.

CAST IRON BENCH Cast iron powder-coated garden bench with 3-seater capacity, designed with integrated seat and backrest for outdoor use. The side frames are made of robust cast iron, while the seat and backrest are fabricated from 14-gauge mild steel pipes, ensuring strength and durability. The bench features a decorative leg design, armrests, and backrest for enhanced comfort. Finished with weather-resistant powder coating suitable for long-term outdoor installation. Dimensions: total height 480 mm, seat height 350 mm, width 410 mm, total length 1225 mm. Load-bearing capacity up to 150 kg

Providing and supplying 900 mm high precast concrete bollards of approved shape and size, made with M25 grade concrete, finished smooth, including reinforcement as required, with provisions for fixing or embedding into the ground, complete with transportation and installation at site as per the Engineer-in-Charge’s direction.

Providing and supplying factory-made precast concrete planter boxes of size 1200 mm x 1200 mm (or as specified), in approved shapes such as rectangular, square, circular, or geometric designs, by KK Manhole & Gratings Co. Pvt. Ltd. or equivalent approved manufacturer. The planter boxes shall be manufactured from M-30 grade reinforced concrete using vibro-compaction for enhanced strength and durability. They shall have adequate drainage provisions and smooth finished surfaces with options for plain grey, terrazzo, or pigmented colors as approved by the Engineer-in-Charge. Designed for outdoor urban landscaping and streetscape applications, the planters shall be weather-resistant and require minimal maintenance. Installation shall be carried out as per specifications and direction of the Engineer-in-Charge.

CARRIAGE OF MATERIALS: SAND (UPTO 38 KM LEAD)

CARRIAGE OF MATERIALS: CHIPS (UPTO 37 KM LEAD)

M/S MADAN PRASAD (BID ID -686217)