SPECIAL REPAIRS TO BLDG NO PSF-05 D BLOCK MD ACCN OF OFFRS JCO OR MD ACCN UNDER GE CENTRAL KIRKEE

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving below or above GL including removing debries outside the MD and depositing where directed complete all as specified and as directed.

M&L for PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in filling for WC complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate as in plinth protection including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ thickness of PCC 75mm complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (1:2:4) using 12.5 mm graded stone aggregate as in levelling course of floor tiling complete all as specified and directed.

Taking down cement or cement lime plaster, any description including raking out joints, hacking for key, scrubbing down with water, etc.and removing the debris outside MD land complete all as specified and directed.

M & L rendering 10 mm thick on brick or concrete surfaces in CM 1:6, finished with sagol finish on plastered surface of internal walls, complete all as specified and directed.

M & L rendering 5 mm thick on concrete surfaces as in ceiling in CM 1:3, finished with sagol finish on plastered surfaces complete all as specified and directed.

M&L for rendering 15mm thick plaster in cm (1:4) on fair faces of brick work or concrete surfaces including finishing the surface fair and even using water proofing compound all as specified and directed. Note: (i) Plaster work in Four story building on wall surface. (ii) Water proofing compound paid and measured separately)

Supply only Liquid water proofing compound complete all as specified and directed.

M&L PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels & drains including necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/stopped ends etc. complete all as specified and directed.

Add or deduct on item no 12 above for each 25mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/stopped ends etc. complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premisess complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar in CM (1:4) for laying of floor tiles complete all as specified and directed.

M&L for non skid ceramic colored tiles 7 to 8 mm thick (Square/ rectangular) each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set in jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for rendering 10mm thick plaster in cm (1:4) on fair faces of brick work or concrete surfaces including finishing the surface fair and even complete all as specified and directed.

M&L for glazed ceramic tiles coloured in vertical surfaces (300 x 200 x 7mm thick) on walls, set & jointed in neat cement slurry & pointed colour cement to match complete all as specified and directed.

M&L for non skid ceramic colored tiles 7 to 8 mm thick (Square/ rectangular) are of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc, set in jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for non skid ceramic colored tiles 7 to 8 mm thick (Square/ rectangular) are of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc, set in jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting/dado complete all as specified and directed.

M&L for 20mm thick screed bed or bedding layer of cement mortar in CM (1:4) for laying of marble flooring complete all as specified and directed.

M&L for Chitter black Marble work 15 to 18 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M&L for Machine cut cudappah stone laid vertical or horizontal 18 to 22mm thick jointed with adhesive to make a cooking platform including dismantling existing RCC/PCC or any type of platform complete all as specified and directed.

S&F in repair for Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets or fixed in cudappah/marble platform including sink coupling and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Dismantling timber fillets, rails, posts rafter purlins under 40 Sqcm in sectional area complete all as specified and directed.

S&F 2nd class HW plain fillets square rectangular triangular in section, clean sawn secured with nails sectional area exc. 13 sqcm but n.exc 25 sqcm complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed

S&F 2nd class HW boarding 25mm thick as in shelves, partition of cup board etc both side plain complete all as specified and directed.

Taking down GI tubing 15mm dia and connection including removable to store or credit to contractor complete all as specified and directed.

Taking down GI tubing 20mm dia and connection including removable to store or credit to contractor complete all as specified and directed.

S&F 15mm bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore GI tubing ISI marked of size 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls. Celing or laid in floors complete all as specified and directed.

Refixing only 15mm tubes any grade, to walls and ceilings or laying in floors including supply and fixing of new fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc. complete all as specified and directed. (Note: Old GI pipes in good condition as retrived from respective item hereinbefore shall be used.)

Refixing only 20mm tubes any grade, to walls and ceilings or laying in floors including supply and fixing of new fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc. complete all as specified and directed. (Note: Old GI pipes in good condition as retrived from respective item hereinbefore shall be used.)

S&F for 15 mm dia PVC connection pipe 450 mm long with two brass fly nuts complete all as specified and directed.

S&F in repairs 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, fancy type chromium plated for iron pipe or for unions complete all as specified and directed.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Disconnecting existing tanks 500 ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes complete all as specified and directed.

S&F for 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0 m m - 2 1 0 g m s ) complete all as specified and directed.

Supply and fix 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) double layered 'ISI' marked, hoisted & fixed in position with existing inlet, outlets & provision of washouts, vent pipe, nipples of suitable size hoisted and fixed in position all as specified in SSR part-I (2009) including dismantling and removal of existing water tank from site complete all as specified and as directed.

S & F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete bedding complete including making good to floor complete all as specified and as directed.

S&F in repair PVC low level flushing cistern 10 ltrs capacity with float ball valve and bracket including fixing of flush pipe & 15mm dia PVC connector pipe 450mm long with two nos brass fly nuts complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls/ floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) branch piece (Double Y) equal or unequal with access door 110mm bore complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore in dia complete all as specified and as directed.

S&F for Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

M&L for 40mm dia GI pipe medium grade cut to shape and fix to wall of sunken floor as spout complete all as specified fixed and directed.

S & F in repairs brass CP shower rose 125mm size with swivel joint including fixing to steel pipe 15mm complete all as specified and as directed.

Taking down and refixing in same opening with Resecuring or easing & adjusting door shutters of any description exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutter without taking off shutter from the frame exceeding 1.50 sqm but not exceeding 4 sqm each & removing from site complete all as specified and directed.

Taking down chowkats or frame with shutter without taking off shutter from the frame not exceeding 1.50 sqm each & removing from site complete all as specified and directed.

Taking down shutter of any description not exceeding 1 sqm each and removing to store or credit to the contractor complete all as specified and directed.

Taking down shutter of any description exceeding 1 sqm each and but not exceeding 2sqm each and removing to store or credit to the contractor complete all as specified and directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet of size 105x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc. including M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good the surface to match with the existing surface complete all as specified and as directed.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet of size 125x60mm for doors, ventilator with single rebates including necessary fixing lugs, hinges, lock strike plate etc. including M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) to fill the frame & making good the surface to match with the existing surface complete all as specified and as directed.

S&F 2nd class HW plain solid straight chowkats/frame wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick second class hard wood plain, framed panelled shutters (any numbers of panels) with panels of timber flat on both side (feathered edges) or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkat complete all as specified and directed

S&F 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares (with sash bars any numbers), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed

M&L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth,not otherwise described, etc treating ends of posts, backs of chowkats, etc., with coal tar complete all as specified and directed.

S&F 25mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as in cupboard door shutters including 6mm thick lipping on all sides of flush shutter complete all as specified and directed.

S&F 75mm long stainless steel medium weight butt hinges , complete all as specified and directed.

S&F in repair 75mm Hasp and staple, safety type, Aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

M&L for PCC 1:3:6 type C1 (using 20mm graded aggregate) as in hold fast blocks including necessary form work complete all as specified and directed.

S&F 200mm size Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F aluminium anodised sliding door bolt plate type, not less than 12 mm dia with and including aminimum 6 Nos bolts and nuts, 4 on bolt plate and 2 on staple plate length of bolt 300 mm fixed to door shutter/frame complete all as specified and as directed.

S&F 100mm long stainless steel medium weight butt hinges for PVC door shutter and frames complete all as specified and directed.

S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F ventilators made out of aluminium alloy powder coated standard hollow section as per approved sample and as per IS specifications, aluminium section of shutters weighting not less than 0.55 kg/RM and rectangular frames of aluminium section 101.6x44.45x3.18mm weighing not less than 2.54kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and directed.

M & L aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 kg/RM, sides and top not less than 0.826 kg/RM double riveted and 0.55 kg for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel wire cloth including all standard fittings complete all as specified & directed.

S&F for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed

S&F for galvanised MS wire mess 0.63mm nominal dia of wire and average width of aperature 1.40mm fixed with tinned tack or galvanised wire staples complete all as specified and directed.

M & L Water proofing treatment to RCC roof slab, walls, chhajjas etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and Brushing neat cement slurry with 3.0kg of cement per sq. metre including taking down old roof treatment any type (b) Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 as in roof slab with mixing of WPC and surface finished even and smooth without using extra cement. (Note: Water Proofing Compound shall be measured and paid separately). (c) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved cold bituminous primer @ 0.25 ltr /Sqm conforming to IS:3384-1986 of area complete all as specified. (c) Laying APP based polymeric membrane minimum weight not less than 3.5kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt. not less than 150 gms/sqm) with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/sqm on the top of membrane surfaces complete all as specified & as directed by Engr in Charge.

M&L for preparation of new plastered wall surfaces and applying two coat of oil bond distemper emulsion white or tined over one coat of primer and one layer of wall care putty on wall complete all as specified and directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of Cement Based paint over a coat of Alkali Resistant Primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of weather proof acrylic emulsion paint (Exterior Grade) over a coat of alkali resistant primer all as specified and as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflorescence salts and treating oil and greasy spots and applying two coat of Cement Base Paint complete all as specified and directed.

M & L for complete removal of existing treatment on wall surfaces and applying two coats of oil bond distemper over one coat of alkali resistant primer complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and as directed.

M&L preparation of new wood/wood based surfaces of not exceeding 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide/zinc chrome primer complete all as specified and directed.

S&F for curtain rails 25mm dia, anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and directed.

M & L for 150 mm dia (internal dia) RCC hume pipe class NP -2 laid and jointed set in cement mortar 1:4 complete with collars laid in trenches including demolition and breaking up of existing drain pipes (SGSW/ AC/RCC) including hunching and benching for 150mm to 300mm dia pipe, and removal of debris from site and deposited where directed complete all as specified and as directed.

M&L PCC 1:3:6 type C2 using 40mm graded stone aggregate in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and as directed.

M & L for precast reinforced cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in manhole covers ,septic tank slab etc. set in CM 1:6 including demolition of existing RCC manhole covers / RCC slabs complete all as specified and directed.

M & L for mild steel TMT bar 10mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for pre cast cement concrete solid block masonry with solid block of the grade C-5, using 20mm graded aggregate set in CM (1:6) including Demolition of PCC block masonry in any type, position and mortar complete all as specified and directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position including scaffolding etc,complete all as specified and as directed.

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.50 mtr depth n.exc.10 Sqm on plan for foundation etc. or for manhole / laying of pipe and getting out in soft / loose soil complete all as specified and directed.

Returning filling in including spreading , levelling watering and well ramming in layers not exceeding 25 cm thick (soil) complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding1.50 mtr above starting point complete all as specified and directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated 1100 volt grade multi stranded FRLS Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan point or one call bell point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 Nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing capping terminal box for mounting ceiling rose/ holders etc. including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one 5 Amps socket point independent including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 Nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, socket including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one 5 amps socket point on same board with other switches including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm as earth lead and connected to earth dolly for one 16amps socket (Power) point independent including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 Nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, socket including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing capping of required size with all fittings and accessories along with one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one two way light point controlled by two, two way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 Nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch etc including dismantling and taking down old unserviceable point wiring and making good to disturbed surfaces complete all as specified and as directed.

M & L for surface sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 6.0 sqmm (Nominal area) drawn through in and including PVC casing capping/PVC conduit size with all fittings and accessories along with one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly including dismantling and taking down old unserviceable wiring and making good to disturbed surfaces complete all as specified and as directed. NOTE: (a)Two run of cable with one run of earth wire and one run of casing capping/conduit will be measured as one length.

S&F 5 Amp switch piano type single pole one way including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F 5 Amp switch piano type two way complete all as specified and as directed.

S&F bell push flush type 5 Amp single pole one way including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F socket flush type 6 amps, 5 pin, 230v including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F ceiling rose surface Bakelite three terminal all including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F lamp Holder insulated body with back plate for batten fitting complete all as specified and as directed.

S&F LED lamp 12 watt, CDL, B-22 cap, (Pin type), 230V, PF-0.95 (min) complete all as specified and as directed. Make-HPL/Havells/CG/Bajaj/ Philips as approved by GE

S&F flush type electronic fan regulator with 5 step type,120 W, AC 240 Volts, 50 Hz including dismantling and taking down unserviceable one complete all as specified and as directed.

S&F call bell electric AC 240 volt, 50 HZ complete all as specified and as directed.

S&F MCB distribution board, as MCB incomer, IP 43 protection, Double door, metal enclosure, SPN, 230 Volts, 8 way ETPN complete all as specified and as directed. Make cat part no.5076-11 of Legrand or equivalent of schneider or ABB as approved by GE

S&F MCB distribution board, as MCCB incomer, IP 30 protection, Double door, metal enclosure, ETPN, 415 Volts, 4 way complete all as specified and as directed. Make cat No.5076-60 of Legrand or equivalent of schneider or ABB as approved by GE

S&F MCB, TPN, 63 Amps, 415 Volts,10 KA complete all as specified and as directed. MAKE- Cat Part No- 4086-83 of Legrand or equivalent of Schneider/ABB as approved by GE

S&F MCB, Single Pole 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve complete all as specified and as directed. Make-cat part no.4085-87 to 4085-95 of Legrand or equivalent of schneider/ABB as approved by GE

S&F MCB, Single Pole and neutral 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve complete all as specified and as directed. Make-cat part no.4086-9 to 4086-17 of Legrand or equivalent of schneider/ABB as approved by GE

S&F ceiling fan of 1200 mm sweep 5 star rated complete including fan necessary regulator, suitable fan rod with suitable clamp, Fan hook fixed on roof by drilling holes fixing fastener etc., nut, bolt & washers complete all as specified and as directed. Make crompton greaves/bajaj/usha as approved by GE

S&F Exhaust fan Metal body light duty 300 mm sweep complete with grill, including cutting holes on wall as per required size and shape, making good the disturbed surface and matching with surroundings etc. complete all as specified and as directed. Make- Havells, cat Part No-Vent air-DS or equivalent in crompton greaves/bajaj/usha as approved by GE

S&F LED Tube light fitting, 18 watt, CDL, 230 Volts, 4 feet long , complete with all accessories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable including LED tube and mounting casing box 2 Nos including dismantling and taking down unserviceable fitting any type complete all as specified and as directed. Make-CG, Cat Part No LCTL-18-CDL (Trim Linea) or equivalent in Bajaj/Philips/HPL/Havells as approved by GE

S&F LED tube light fitting with LED tube, 2' long, 09 watt, CDL, 230 Volts , complete with all accessories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm two core copper flexible conductor cable with mounting casing box 2 Nos including dismantling and taking down unserviceable fitting any type complete all as specified and as directed. Make-CG, Cat Part No-LCTL-9-CDL (Trim Linea) or equivalent in Bajaj /Philips /HPL /Havells as approved by GE

S&F LED security light fitting, 25 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20/25mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener including dismantling and taking down unserviceable fitting any type complete all as specified and as directed. Make-CG, Cat Part No LSTS-25-CDL or equivalent in Bajaj/ Philips/ HPL/ Havells as approved by GE

M & L for Earthing complete with galvanized steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanized steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2 with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wire mesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal complete all as specified and as directed in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion complete all as specified and as directed.

Supply and lay LT UG cable 3.5 core 35 sqmm XLPE insulated sheathed armoured 1100 volts grade with aluminium conductor laid in trenches complete including indoor/ out door joint complete all as specified and as directed.

Supply and lay LT UG cable 3.5 core 50 sqmm XLPE insulated sheathed armoured 1100 volts grade with aluminium conductor laid in trenches complete including indoor/ outdoor joint complete all as specified and as directed.

Supply and laying in trenches clamped on pole/wall, laid under floor, GI pipe of size 40 mm dia light grade including taking out unserviceable one complete all as specified and as directed.

Material and labour for dry crushed stone dust cushioning to underground cables in trenches including spreading, leveling, hand punning and consolidating, complete complete all as specified and as directed. Note; Punned thickness of stone dust shall be measured for payment purpose.

M & L for reinforced precast concrete cable cover class LV type -1 flat of size 250mm x 150mm x 40 mm for cable protection complete all as specified and as directed.

Veekay Enterprises

Shri Sant Cosntruction

V.R.PRAJAPATI AND CO.

S.R.M.K Enterprises