REPAIR MAINT TO INTERNAL ROAD POT HOLES INCLUDING KERB STONE, INTERLOCKING PATH, DRAIN COVERS, INCLUDING BERMS AND FOOTPATH AT AOR OF AGE B/R-I UNDER GE (EAST) AGRA

Amount

Demolition of reinforced cement concrete as in ground floors and pavings not exc. 15 cm thickness (above or below) complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

Scarifying or picking gravelled macadam or bituminous macadam surface exc 50 mm and n. exc. 100 mm deep in area exc. 400 Sqm and removing n.exc. 50 m complete all as specified and directed.

M&L for moorum / red bajri, spread, rolled and consildated to gradient and camber required spread thickness of layer 100 mm complete all as specified and directed.

Repair to pot holes any depth, not exc. 1 Sqm each including sweeping free from dust and mud or water scoring sunken surfaces in roads, paths but making good by applying tack coat @ 5 kg / 10 sqm putting permixed bituminous macadam well ramming and sealed with binder 9.8 kg per 10 sqm blinded with 0.09 cum of stone chipping 6.3 mm size and again well rammed (including supply premixed macadam binder and chipping) depth of pot holes exc. 30 mm complete all as specified and directed.

M&L for 10 cm thick compacted thickness WBM, with coarse aggregate of grading 1 (90 to 40 mm size) spread, rolled and consolidated to gradient and camber required type of aggregate granite, trap or basalt spread rolled with 8 to 10 tonne power roller and consolidating to required gradient and camber complete all as specified and directed.

M&L for preparing unsurfaced water bound macadam by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bag or using air compressor to remove all loose dirt etc complete all as specified and directed.

M&L for applying evenly a priming / tack coat with bituminous primer (paving bitumen VG-10) @ 10 kg per 10 sqm over the prepared WBM surfaces by mechanical sprayer complete all as specified and directed.

M&L for preparing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bag or using air compressor to remove all boose dirt etc complete all as specified and directed.

M&L for applying evenly a priming / tack coat with bituminous primer (paving bitumen VG-10) @ 5 kg per 10 sqm over the prepared black top surfaces by mechanical sprayer complete all as specified and directed.

M&L for premix bituminous macadam (Design mix) (consolidated thicked 75 mm or less) with 4% binder content using paving bitumen VG-30 grade by weight of total mix laid and rolled and compacted to required camber and gradient with 8 to 10 tonne vibratory road roller complete all as specified and directed. Note :- (a) Premix concrete shall be mixed in hot plant, transported from plant to work site and laid / spread by means of mechanical sensor paver. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item if there is any variation in the actual binder content used in lower side, the rate shall be adjusted @ Rs.45/Kg. However no price adjustment shall be made if the binder content works out to more than as specified above.

M&L for laying bituminous premix asphaltic semi dense concrete (Design mix) 30 mm consolidated thickness with 5.5% binder content by weight of total mix, (Paving bitumen VG-30) rolled and compacted with 8 to 10 tonnes vibratory road roller to required camber and gradient complete all as specified and directed. Note :- (a) Premix concrete shall be mixed in hot mix plant, transported from plant to work site and laid / spread by means of mechanical sensor paver. (b) Contractor shall quote his rate on this basis of binder as mentioned in above item if there is any variation in the actual binder content used, the rate shall be adjusted @ Rs.45/Kg lower side of binder used. However no price adjustment shall be made if the binder content works out to more than as specified above.

M&L for preparing bituminous surface of road and marking 2.5 mm thick centre lines, stop lines, dashes, arrow etc and the like n.exc 10 cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour including spreading of glass beads confirming to BS-3262-1989 with special applicator matchine all as per manufacturers instruction complete all as specified and directed.

M&L for M-25 (design mix) as in surface channels of RCC drain including RCC cover for drain complete all as specified and directed.

M&L for providing pre-cast RCC 1:2:4 type B-1 using 20 mm grade stone aggregate as in cover (for manholes and drains) including necessary form work set in CM 1:4 complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

M&L for TMT bar 8 mm dia cut to length bent to shape required inclidng cranking bending, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for TMT bar 10 mm dia cut to length bent to shape required inclidng cranking bending, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Form work to soffits of suspended slabs as roof slabs, landings, lintel / chajja and similar work not exceeding 200 mm thick for fair finished surfaces of concrete complete all as specified and directed.

Form work to flat faces of walls, retaining walls, abutments, parapets and stair case railing and similar work including attached pillasters, buttresse etc vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

M&L in repairs MS framed work grills, grating, etc with ends of bars shouldered and / or riveted or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe 290, Gde E-165 made to shape and placing in position complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size, straight or curved on plan exc. 6 M mean radius built in CM 1:6 complete all as specified and directed.

M&L for rending 15 mm thick cement plaster in CM 1:4 on fair faces of brick work / concrete surfaces & finishing the surfaces even and smooth without using extra cement etc complete all as specified and directed.

Demolition of cement concrete as in ground floors and pavings not exc. 15 cm thickness (above or below) complete all as specified and directed.

M&L for cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) in coping complete all as specified and directed.

M&L for preparation of newly plastered surface of brick / concrete surfaces of any description over 10 cm girth or width not otherwise described and applying two coats of synthetic enamel paint (any tint) over a coat of water proof putty etc complete all as specified and directed.

Taking down / dismentling of old precast interlocking paver block and chequered tiles of any size and shape any description and in any position complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

Provding and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawn, drive ways or light traffic parkingetc of required strength thickness & size / shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding / laying of interlocking paver blocks into the sadn bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for complete removal of existing treatment of old paint of concrete, surface / kerb stone, including cornices, pilaster etc by washing, rubbing, down, scraping and stopping hole etc and apply two coats of synthetic enamel paint over and including 1 mm thick Birla / JL Wall care putty complete all as specified and directed.

Supply and fixing cat eye solar refelctive type of metal body alloy of size 100 mm x 100 mm x 20 mm with PAMA striplens reflector of model No. DA 972.0 fixed with and inclding MS stud of suitable size as per manufacturer instructions complete all as specified and directed.

S&F in repair safety traffic safe PVC unbrakable convex mirror (80 cm ) made of poly carbonate / ABS / Fibre including fixing arrangements, fixed to MS pipe 50 mm dia and 1.5 mtr high from ground level, duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and embedded in ground with and including PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate), excavation, returning, filling, removal etc of size (250 mm x 250 mm x 400 mm) complete all as specified and directed. Note :- The rate for excavation, removal of soil & PCC complete shall be included in above quoted rate.

DHARMENDRA GAUTAM (BID ID -3488907)