Raising of 1st floor laundary block for shifting CSSD from present location for procurement of two additional oxygen concentrator plant at CSSD at SKIMS.

Amount

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of :( G.S. Sheet)

Dismantling steel work in built up sections in angles, tees, flats and Channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. Including dismembering and stacking within 50 meters lead.

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(Welded)

Labour charges for fixing of available structural steel including welding cutting hoisting in position and applying priming coat of approved steel primer of all complete.

providing corrugated G.S sheet roofinf including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.( 0.63 mm thick with zinc coating not less than 275 gram/m2)

p/f of galvanized iron plain sheets 0.50 mm thick U-shaped gutters 150*100*100 mm width with necessary iron flats, bolts screws and rivets etc.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with : (1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including all carriage

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters.( 80x0.90 mm M.S. laths with 0.90 mm thick top cover)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :( (Cement mortar 1:6 ( 1 cement : 6 coarse sand) including carriage

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 coarse sand) including all carriage

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.(35 mm) First class deodar wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :35 mm(First class deodar wood)

p/f of 35 mm thick first market flush door shutters non decorative type solid core of back board 0.80 mm thick lamination on back side and lipping of first class deodar wood complete job

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

p/f of 3.5 mm thick glass panes including cost of wooden beading nails etc complete

p/f of 5mm thick glass panes including rubber gasket etc complete

p/f of hardware fitting of approved make

(a)tower bolt 100 mm

(b)handle 100 mm

(C)link lock 8”

(d.)link lock 12 “

(e).alumuninum tubular handle (powder coated)200 mm

(f) tower bolt 200 mm (powder coated

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo / Fir wood

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws Budloo/fir wood

p/f of 50 mm thick glass wool of standard quality properly placed in wooden frames including cost of screws washers and G.I chicken mesh complete job.

10 mm thick plywood ceiling in (2’.0’ * 2’.0”) panels including 20 mm widee beading on joints and painting with synthetic anaul paint and priming comp. job

p/f alumunium work for doors windows ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)

(a) Powder coated aluminum (minimum thickness of powder coated 50 microns) frames

(b) Powder coated aluminum (minimum thickness of powder coated 50 microns) shutters

ACP sheets in partitions panels shuttlers etc including cost of rubber neoprene gasket EPDM screws etc comp. 5 mm

Pebble dash plaster upto 10m height above ground level with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 Coarse sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. including all carriage

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(2mm thick

Applying one coat of water thinkable cement primer of approved brand and manufacture on wall surface.

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level(Thermo-Mechanically Treated bars of grade Fe-500D or more.)

Centering and Shuttering including strutting propping extra and removal of form work for lintels beams girders extra complete

p/f first quality ceramic glazer wall tiles confirming to IS 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(7-8 mm)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more , of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete(10 mm)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing ball valve (C.I) of approved quality.

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

50 mm dia. nominal bore

p/f of PVC pipe prince/equivalent make comp. Job

(a) 100 mm dia

(b) 75 mm dia

PVC fittings prince or equivalent make(b-type)

(a) Door tee 100 mm

(b) Door junction 100 mm

(c) plane bend 100 mm

(d)Collar 100 mm

(e)P trap 100 mm

(f)Floor trap 100 mm

(g)Door trp 75 mm

(h)door junction 75 mm

(i)Plane bend 75 mm

(j)Collar 75 mm

(k)P trap 75 mm

p/f white vitreous chins pedestal type water closet (European type) with seal and lid,10 litr. Low-level white P.V.C flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required

p/f PVC low level flushing cistern with manually controlled device(handle lever) conforming to IS:7231 with all fittings and fixtures complete(10 Lit )

p/f of wash basin pedestal type complete job of paryware/hindware

p/f of C.P fittings of approvedmake(parko/Jaquar)

(a)bib cock

(b)wall mixer

p/f of looking mirror of standard quality

p/f of soap case of standard quality

p/f of towl rod of standard quality

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

NAZIR AHMAD HAKAK

TEHSEEN CONSTRUCTIONS PVT. LTD.

MOHAMMAD ASHRAF DAR

M/s Peer Aijaz Amin

M/S AL-ARZ CONSTRUCTIONS

GHULAM JEELANI BHAT