Providing and fixing kitchen and wardrobe in the newly constructed 1300 Sft and 1900 Sft Houses in PWD Colony at Gurugram.

Amount

Supply, Providing and placing Kitchen Cabinets. Floor unit consist of plain shelf, Grocery unit, Cooking kit with Tranquil, Drawer utensil kit with tranquil, Edge corner, filler and cover panels which have different width according to the layout. The kitchen cabinets with openable shutters and sufficient number of drawers made of 0.5mm body panels and 1.2mm thick horizontal (sandwich sheets) Frames of Galvanised sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Shutters MDF plus back painted glass shutter with aluminium profile handle.Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges ( Blum, Hettich approved make) i/c soft/Auto closing hinges 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality. Finished components shall be tested for the critical quality parameters, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.2 mm with even wire basket in SS 304 grade. Steel carcass shall have passed the test like Static Load test, Shelf deflection test. Modular kitchen accessories to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.6mm-0.8mm as per technical requirement.The carcase of floor units will be supported by 100mm to 120mm height vertical adjustable legs (Hettich or equivalent approved) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminium finish attached by hardware of skirting. The unit shall be fixed to the floor/wall/slab using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared in sample flat at site and direction of Engineer-in-charge. Only face area of openable shutter and drawer shall be measured. Cabinet depth of 450mm to 550mm. (New)

Supply, Providing and placing Kitchen Top cabinets with openable shutters and having 0.5mm body panels and 1.2mm thick horizontal Frames of Galvanised sheet with in sandwich form zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Shutters MDF plus back painted glass shutter with aluminium profile handle. Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges (Hettich approved make) i/c Normal closing hinges 90 to 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality. Finished components shall be tested for the critical quality parameter, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.0mm to 1.2mm. Steel carcase and shutters shall have passed the test like Static Load test, Shelf deflection test. The unit shall be hanged on to the wall using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared for in sample flat at site and direction of Engineer-in-charge. Only face area of openable shutter and drawer shall be measured. Cabinet depth 300mm to 310 mm. (width will be measurable according to drawing approved by engg. it will consists of top units which will have Different width having different height and Gtpt unit having accessories. .((NEW)

Supply, Providing and placing Kitchen Drawers for Crockery Unit cabinets with openable shutters and sufficient number of drawers made of 0.5mm body panels and 1.0mm to 1.2mm thick horizontal (sandwich sheets) Frames of Galvanised sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges (Hettich approved make) i/c Normal closing hinges 90 to 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality.Finished components shall be tested for the critical quality parameters, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.2 mm with even wire basket in SS 304 grade. Steel carcass and shutters shall have passed the test like Static Load test, Shelf deflection test. Modular kitchen accessories to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.5mm to 0.6mm as per technical requirement. The carcase of floor units will be supported by 100mm height vertical adjustable legs (Hettich or equivalent approved) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminium finish attached by hardware of skirting. The unit shall be fixed to the floor/wall/slab using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared in sample flat at site and direction of Engineer-incharge. Only face area of openable shutter and drawer. Cabinet with depth of 550mm to 560mm. Floor unit consist of plain shelf for crockery item with filler and cover panels which have different width according to the layout. . (new)

Supply, Providing and placing Kitchen Cabinets. Floor unit consist of plain shelf, Grocery unit, Cooking kit with Tranquil, Drawer utensil kit with tranquil, Edge corner, filler and cover panels which have different width according to the layout. The kitchen cabinets with openable shutters and sufficient number of drawers made of 0.5mm body panels and 1.2mm thick horizontal (sandwich sheets) Frames of Galvanised sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Shutters MDF plus back painted glass shutter with aluminium profile handle. Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges ( Blum, Hettich approved make) i/c soft/Auto closing hinges 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality. Finished components shall be tested for the critical quality parameters, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.2 mm with even wire basket in SS 304 grade. Steel carcass shall have passed the test like Static Load test, Shelf deflection test. Modular kitchen accessories to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.6mm-0.8mm as per technical requirement. The carcase of floor units will be supported by 100mm to 120mm height vertical adjustable legs (Hettich or equivalent approved) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminium finish attached by hardware of skirting. The unit shall be fixed to the floor/wall/slab using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared in sample flat at site and direction of Engineer-in-charge. Only face area of openable shutter and drawer shall be measured. Cabinet depth of 450mm to 550mm

Supply, Providing and placing Kitchen Top cabinets with openable shutters and having 0.5mm body panels and 1.2mm thick horizontal Frames of Galvanised sheet with in sandwich form zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Shutters MDF plus back painted glass shutter with aluminium profile handle. Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges (Hettich approved make) i/c Normal closing hinges 90 to 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality. Finished components shall be tested for the critical quality parameter, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.0mm to 1.2mm. Steel carcase and shutters shall have passed the test like Static Load test, Shelf deflection test. The unit shall be hanged on to the wall using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared for in sample flat at site and direction of Engineer-incharge. Only face area of openable shutter and drawer shall be measured. Cabinet depth 300mm to 310 mm. (width will be measurable according to drawing approved by engg. it will consists of top units which will have Different width having different height and Gtpt unit having accessories. (new)

Supply, Providing and placing Kitchen Drawers for Crockery Unit cabinets with openable shutters and sufficient number of drawers made of 0.5mm body panels and 1.0mm to 1.2mm thick horizontal (sandwich sheets) Frames of Galvanised sheet with zero spangles (as per ASTM A653), components shall be powder coated with high quality powders like Dupont, Kanasai Nerolac with dry film thickness of 40 to 60 microns with pencil hardness of 2H Min. All shelves shall be supported on approved quality Self supporter and shall be adjustable for different heights as per requirements. Each shutter shall be fixed to the framework/carcass using two numbers of best quality CED coated hinges (Hettich approved make) i/c Normal closing hinges 90 to 95 degree as per requirement (Hettich make or equivalent) fixed with SS screws , nails etc complete and these shutters are provided with an approved quality.Finished components shall be tested for the critical quality parameters, Adhesion and impact test which enhances the life of kitchen. Shelves to be of galvanised steel sheet with thickness of 1.2 mm with even wire basket in SS 304 grade. Steel carcass and shutters shall have passed the test like Static Load test, Shelf deflection test. Modular kitchen accessories to be fixed in the drawer/Cabinet with suitable provision with panels of bottom and rear shelves with thickness of 0.5mm to 0.6mm as per technical requirement. The carcase of floor units will be supported by 100mm height vertical adjustable legs (Hettich or equivalent approved) which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminium finish attached by hardware of skirting. The unit shall be fixed to the floor/wall/slab using metal screws of appropriate size and rawl plugs. The work shall be executed as per drawing/Sample prepared in sample flat at site and direction of Engineer-incharge. Only face area of openable shutter and drawer. Cabinet with depth of 550mm to 560mm. Floor unit consist of plain shelf for crockery item with filler and cover panels which have different width according to the layout. .(new)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS: 513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using.1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 1200-1250mm Width Body and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 1200mm to 1250 mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel.Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc.Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contract. .(New)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS:513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using 1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 1500mm to 1650 Width Main and Add-On Combination Body with door and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 1500mm to 1650mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel.Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc.Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contract. . (new)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS: 513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 2000mm to 2100mm Width Main and Add-On Combination Body with door and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 2000mm to 2100mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel.Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc. Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contract. .(new)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS: 513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using 1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 1200mm to 1350mm Width Main and Add-On Combination Body with door and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 1200mm to 1350mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel. Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc. Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contract. .(new)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS: 513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using 1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 1500mm to 1750mm W Main and Add-On Combination Body with door and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 1500mm to 1750mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel.Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc. Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contrac(new)

Supply, Providing and placing Storage from the flats walls. Body and Shelves or hanging Rod Specifications as per required. The Side panel, Top panel End cover is made using 0.5 mm CRCA (IS: 513). Back panel is made using 0.5mm CRCA (IS: 513). The top and bottom stiffener is made using 1.2mm CRCA (IS: 513). Bottom panel in (600mm) is made using 0.5 mm CRCA (IS: 513). End Legs are made up of 1.2mm CRCA with leg bush welding on it. Tube and insert moulded leveller assembly is inserted on leg bush. In 560D unit, the leg used is 80mm in height. Shelves used are 10 bend panel made of 0.5mm CRCA (IS: 513). Shelf panels are placed on shelf support and then fixed using nut and bolts from below. Standard configuration Consists of 3 shelves for main body 560D. Hanging rail comprises of 2 injection moulded holders mounted on the shelf and a hanging rod. Hanging rod is made of Aluminium and is silver anodized. Hanging rod is having 392 mm width for 450W body and 542 mm width for 3000mm to 3400mm Width Main and Add-On Combination Body with door and height approx.2400mm and depth is 500mm to 570mm. Metal hinged door comes in two widths For 3000mm to 3300mm Width unit: LH door - 598 x 2498 x 18 / RH door - 598 x 2498 x 18 Construction - Aesthetically appealing plain, made from 0.5 mm CRCA steel stiffeners’, outer cover panel is 0.75 mm pre coated sheet 0.6 mm CRCA inner cover panel.Aluminium handle is attached vertically to the door. Hardware- High quality standard hardware like screw, washer, lock, Door hinges, bumpers, Handle, etc. Construction - Completely Knock down construction Finish- All MS sheet metal and metal frame components are powder coated with epoxy polyester powder to the minimum thickness of 45 microns. Colour confirmation buyer choice after award of contract. . (new)

G D INTERNATIONAL (BID ID -1329076)

Handa & Chopra (BID ID -1328266)