SPL REPAIR OF OFFRS MD ACCN QTR NO 437/1, 437/2 AND 555/2 AT JAIPUR MIL STN

Taking down cement plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish outside MoD land complete all as directed.

M&L for Raking out joints/pointing to stone masonary work in walls or to bricks on edge in floors, surface channels, roofs, etc. complete all as specified and directed.

Dismantling of cement concrete tiles,glazed tiles, terrazo tiles in floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish outside MoD land complete all as specified and directed.

Demolition of cement concrete (un-reinforced) at any floor and pavings not exceeding 15 cm thickness below or above ground level incl removing the rubbish outside MoD land in low laying area complete all as specified and directed.

Demolition of reinforced cement concrete any description as in roofs, floors (Other than ground floors), beams, staircases, landing, chajjas, slab, RCC water storage tanks & similar suspended work incl removing the rubbish outside MoD land in low laying area complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L 15 mm thick rendering in cement mortar (1:4) plaster on stone masonary/concrete surfaces on other than fair faces finished even and smooth complete all as directed and specified

M&L rendering 10mm thick in CM 1:3 n exc 3.00 sqm each patch in ceiling patches in ceilling finished even and smooth without using extra cement complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M&L Non- skid coloured ceramic matching tiles 7 to 8mm thick (square / rectangular)(MATT FINISH) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. Set & jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete & including 15mm thick screed bed in cm 1:6 complete all as specified and directed.

M&L for non skid coloured ceramic matching tiles 8 to 9.5mm thick (square / rectangular)area of each tiles exc 0.11 sqm but not exceeding 0.18 Sqm in floor etc & jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete including 15mm thick screed bed in cm 1:6 / or by adhesive complete all as specified and directed.

All as per item no 11 but as in skirting and jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete and including 10mm thick as in back coat CM 1:4 complete all as specified and directed .

M&L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete including 15mm thick screed bed in cm 1:6 / or by adhesive complete all as specified and directed.

All as per item no 13 but as in skirting and jointed in neat cement slurry & jointed in coloured cement to match the colour of tiles over complete and including 10mm thick as in back coat in CM 1:4 complete all as specified and directed .

M&L coloured Glazed ceramic tiles in verticle surface (300x600mmx7mm) thick, (digital tiles) as dado etc laid in concept/pattern using highlighters set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles and including 10mm thick CM 1:4 complete all as specified and directed .

M&L for chequered tiles cement concrete tiles 20x20x25cm thick, set jointed & pointed in neat cement slurry in floors with grey cement & pigment over 20mm thick screed bed in cm 1:6 complete all as specified and directed.

M&L 15-16 mm thick Granite work (table rubbed & polished) in cooking plat forms,window cill & edges, steps, jamps, pillars in single piece and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite complete all as specified and directed.

Rounding to edges of stone slab ( granite) two edges such as in cooking platform complete all as specified and directed.

M&L Kota stone slabs, 20-25mm thick, machine cut as in cocking platform,thread of stair and flooring , set and jointed in cement slurry over & including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting complete all as specified.

M & L for 25-30 mm thick green Marble stone machine cut, bedded jointed as in verticle support and pointed with grey cement slurry including cutting complete all as specified and as directed.

S & F 18-20 mm thick HDHMR (High density high moisture resistant) board for Kitchen cupboard/door shutter of Action tesa or equivalent one side colour/white laminate and other side decorative as in modular kitchen/ cabinets/door shutter fixed with minifix hardware where ever required including edge band 22 mm wide 0.80 m thick of matching colour on exposed surfaces of board fixed with polymaster adhessive of REHAU make or equivalent including trimming edges of edge band to true line of thicknesss of board by manual trimmer,fixed to wall etc complete all as directed

S & F 8 mm thick HDHMR (High density high moisture resistant) board of 'Action tesa or equivalent both side white laminate as in back of kitchen cabinets/partion of cupboard etc.complete all as directed

S & F kitchen plain baskets of stainless steel size 17" x20" x 4" of grade SS-304complete all as specified & directed.

S & F kitchen prerforated cutlery baskets of stainless steel size 17" x20" x 4" of grade SS-304 complete all as specified & directed.

S & F kitchen cup & saucer baskets of stainless steel size 17" x20" x 4" of grade SS-304 complete all as specified & directed.

S & F kitchen plate baskets of stainless steel size 17" x20" x 6"of grade SS-304 complete all as specified & directed

S & F kitchen grain baskets of stainless steel size 17" x20" x10" of grade SS-304 complete all as specified & directed.

S & F stainless steel basket guide channels suitable for running basket as mentioned in item 24-28 above of grade SS-304 complete all as specified & directed.

S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed.

S & F 4.8 mm thick glass not exc 0.5 sqm in each pane as in cabinet shutters fixed with beads of approved make complete all as specified & directed

S & F stainless steel handles of size 200 mm fancy type of approved make complete all as specified & directed.

S & F stainless steel tower bolt of size 150 mm fancy type of approved make complete all as specified & directed.

S&F Auto close hinges, stainless steel, bright finish or electrogalvanised.

S&F magnet for cupboard stainless steel, bright finish or electrogalvanised.

S&F stainless steel, bright finish or electro galvanised cupboard lock all as specified and directed by engineer In-charge

S & F in repair kitchen sinks made of stainless steel sheet 1mm th of grade SS-304 incl washer, brass sink coupling, waste pipe, bowl size 495 x 420 x160 mm fixed in kitchen granite top incl cutting granite/ marble of cooking platform complete all as specified and directed.

S & F in repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, fixed in kitchen granite top incl cutting granite/ marble of cooking platform connecting union overall size 915mmx460mm complete all as specified and directed.

Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

Taking up or down 25 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

S&F15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor including concealed where required complete all as specified and directed.

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor including concealed where required complete all as specified and directed.

S&F 25 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S&F in repair bib taps 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in repair bib taps 15mm bore 2-in-1 cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in repair kitchen mixer 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union for kitchen complete all as specified and directed.

S&F in repair sink cock 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in repair WHB mixer 15mm bore swan neck cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. Makes : Jaquar, Kohler & Grohe

S&F in repair brass CP towel rail 60 cm long square complete all as specified and directed.

S&F SS towel ring square including Chromium plated brass screws & plastic rawl plug complete all as specified and directed.

S&F Soap dish, CP brass square fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair Brass chromium plated shower rose incl shower arm with or without swivel joints, any size, including fixint to steel pipe or union complete all as specified and directed.

S & F in repair 15 mm dia Angle valve/stop valve, cast copper alloy chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed.

S & F PTMT alloy bathroom cabinet with mirror of overall size 300 x 450mm complete all as specified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm bore gate valve gun metal screwed down high pressure with iron wheel head screwed both ends for iron pipe or for union complete all as specified and directed.

S & F Glass Shelf 600mm Long complete all as specified and directed. Cat No : AcN1171N Make : Jaquar Or (Make: Hindware,Cat Part No : F870011) Or (Make: Cera,Cat Part No : F5005301) or equivalent in list of approved makes.

S&F in repair 20mm bore gate valve gun metal screwed down high pressure with iron wheel head screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair Wall Mixer with Provision For Overhead Shower, Connecting Legs & Wall Flanges ,screwed the ends for iron pipe and plugging complete all as specified and directed.

S & F 250 mm Corner Glass shelf with brass brackets complete all as specified and directed.

S&F in repairs vitrous china squatting pan of size 580 x 440 mm (Orrisa pattern), white with integral foot rest (excluding flushing cistern & flush pipe) including antisyphonage pipe complete all as specified.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .

S&F in repair Single Piece-WC with soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, including P/S trap all as specified and directed.

S&F brass CP health faucet 1.2m chain etc complete all as specified and directed .

S&F brass CP toilet paper holder with flap.

S&F in repairs vitreous china wash hand basin with pedestal white flat back excluding taps, waste, chain & plug and porcelene stopper but including brackets /fastners, cutting for and pinning in ends of brackets but inclussive of fixing of supplied CP waste coupling/grating and waste pipe/CP bottle trap. (Note: supply of waste pipe/CP bottle trap and CP waste coupling/grating are taken separate).

Supply only 32 mm bore brass CP coupling with long shank for wash hand basin.

Supply only brass CP bottle trap 32mm etc complete all as specified and directed .

S & F in repair 15 mm dia stop cock ( concealed type) , cast copper alloy chromium plated , fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed etc complete all as specified and directed.

S&F in repair brass CP towel rack made by square/round pipes complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material outside of MD Land complete all as specified and directed.

M & L brick work using Subclass B bricks in exc. 6 m mean radius on plan built in cement mortar 1:6 complete all as specified and directed.

M & L brick work in half brick thick wall using Subclass B bricks built in cement mortar 1:6 complete all as specified and directed.

M&L for random ruble uncoarsed stone masonary well bonded , bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

Dismantling of 75mm bore PVC soil/ waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed

Dismantling of 110mm bore PVC soil/ waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified and directed..

S&F75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110 mm dia PVC (SWR) junction single (Single Tee) equal or unequal complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm dia PVC (SWR) junction single (Single Tee) equal or unequal complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F PVC (SWR) reducers (110 x 75 mm) complete all as specified and directed.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F 75 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC (SWR) 75 mm dia of outlet nahani trap/floor trap with grating including jointing with solvent cement complete all as specified and directed.

S& F PVC (SWR) gully traps of size 125/110 mm setting and jointing with solvent cement complete all as specified and directed.

S&F PVC clamps for rain water , soil, waste pipe incl bolts if required for securing/ holding in position pipes of dia 75 mm complete all as specified and directed.

ditto as item no 90 - but 110 mm complete all as specified and directed.

Dismantiling and S&F new 500 litres, rotational moulded polyethylene three layered water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position incl20mm bore ball brass wall connecting pipes, nipple/ sockets e complete all as specified in SSR Part I complete all as specified and directed.

Dismantiling and S&F new 1000 litres, rotational moulded polyethylene three layered water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position incl connecting pipes, nipple/ sockets incl 20mm bore ball brass wall, dismantling existing water tanks and removing tostore complete all as specified in SSR Part I complete all as specified and directed.

Taking down and re-fixing after easing to shutters of any description exceeding 1 sqm and n.exceeding 2 sqm each in the other opening or same opening complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed. .

S & F 35mm thick flush shutters solid core construction with block board and plywood face panels, fixed with approved adhessive incl lipping all round the edges of door as per manufacturers instructions

M&L for decorative laminate type 1, 0.9 mm thick colour and pattern as approved fixed as in door shutters complete all as specified and directed.

S & F 35mm thick second class hardwood factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc divided into square , with plain, chamfered or rounded, mitred and rebated sash bars any numbers , fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S & F 35mm thick factory made partly gauzed and partly panelled skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed to wodden door shutters complete all as specified and directed.

S&F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed to wodden door shutters or any type of windows complete all as specified and directed.

S&F aluminium mesh of weight exc.0.55 Kg/Sqm as support to SS wire clothcomplete all as specified and directed.

S & F for coloured Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet wood grain printed reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F for 35 mm thick Factory made solid EPS core PVC Moulded coloured Door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design, consisting of frame made out of MS tube 20 mm x 40 mm. The core panel shall consist of 25 mm thick high density EPS routed with design, sandwitched in between front side moulded prelam 2 mm thick Moulded PVC sheet on one face and 2 mm PVC sheet on other side. The shutter on all edges to be sealed with lipping of 10 mm (5mm x 2) thick x 25 mm wide PVC sheet on other side & 60 mm wide PVC sheet for lock lock rail side . the lipping shall be bonded to the 2 mm moulded / plain PVC sheet with solvant cement asas specified and shown on serial pages No. 142, 143, 144 , 145 & 146 of SSR 2010 (Part-II) and Particular specification & as directed by Engineer-in-charge.Note :- (i) The PVC doors shall be fixed as per manufacturer's instructions and as directed by Engineer-in-charge.

S &F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings;sheds, door frame ,framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F mortice lock for main door of Godrej locking solution and system ELC-06 -6 Lever door handle with loc set satin steel complete all as specified and directed.

S & F SS butt hinges 100mm size medium weight and fixed as directed and specified.

S & F in repair 250 mm long aluminium sliding door bolt with hasp, staple (bolt type) not less than 12 mm dia with & minimum of 6 bolts & nuts , 4 on bolt plate & 2 on staple plate complete all as specified and directed.

S & F in repair aluminium anodised handles cast moulded type 150mm size fixed with screws complete all as specified and directed.

S & F aluminium barrel tower bolts of extruded section, 150mm long as specified complete all as specified and directed.

S & F in repair aluminium barrel tower bolts of extruded section, 200mm long as specified complete all as specified and directed.

S&F aluminium anodized barrel tower bolts 200mm long of extruded section complete all as specified and directed.

S&F aluminium anodized handle 150mm long, cast type complete all as specified and directed.

S&F aluminium anodised sliding door bolt 250mm long with hasp and staple (bolt type an fixing clips of sheet or extruded section an fixing bolts and sliing bolt of extruded section complete all as specified and directed.

S & F 75 mm long door stopper of stainless steel body with two number rubber shoes complete all as specified and directed.

S & F MS Helical door spring150mm long including roller and roller plate complete fixed to angle iron chowkats. complete all as specified and directed.

S&F for 4 mm thick glass sheet odinary quality and glazing with neosprene beading/silicon etc n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair 25 mm dia SS drapery rod grade 304 medium weight complete all as specified and directed.

S&F SS -304 grade brackets/ end brackets for holding drapery rod with good quality SS finials for drapery rod 25 mm dia all as specified and as directed. (Note : Finials pairs and backets pais are counted separately) complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed

M&L preparation old untreated steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint over complete all as specified and directed

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed

M&L for preparation of old painted wooden or wood based surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint over complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted by mechanical means over a coat of primer over a coat of 1mm thick wall care putty to make smooth the undulated surfaces complete all as specified and directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.) Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

M&L for complete removal of existing treatment on walls, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted by mechanical means over a coat of primer over a coat of 1mm thick wall care putty to make smooth the undulated surfaces complete all as specified and directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.) Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior acrylic emulsion paint by mechanical means over a coat of primer and over 1 mm thick wall care putty complete all as specified and directed. Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

M & L Complete removal of existing treatment of old plastered surfaces of walls and Washing, rubbing down and stopping of painted surfaces and applying two coats of exterior acrylic emulsion paint by mechanical means over a coat of primer and including 1 mm thick wall care putty complete all as specified and directed. Note : the surface should be even and smooth after applying the wall care putty irrespective of number of coating applied and as per direction of Engr in charge/GE

M & L for preparation of old plastered surfaces of walls & applying two coats of white wash ccomplete all as specified and directed.

M & L for preparation of new plastered surfaces of walls & applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered surfaces & applying three coats of white wash on ceilings complete as spd & directed

M & L Complete removal of existing treatment of old plastered surfaces of ceilling and Washing, rubbing down and stopping of painted surfaces & applying two coats of white wash by mechanical means complete all as spd & directed

M&L Providing, cement concrete Type B1 1:2:4 (20 mm graded aggregate,on lintels up to 1.5m clear span, bed plates,coping, kerbs water trough & the like including weathering, slightly rounded or chamfered angles & throating, as directed

Taking down existing roof tiles/PCC/any type of treatment on roof/terrace of any description complete all as specified and directed.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement. complete all as specified and directed

M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and smooth complete all as specified and directed

Supply only liquid water proofing compund complete all as specified and directed.

S&F fiber reinforced UV resistant elastomeric liquid applied waterproofing & heat reflective coating with acrylic polymers and polyester/glass fibers after scraping and properly cleaning the surface to remove loose particles with wire brushes complete or as directed over a coat of primer as per manufacturers instr.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (40mm graded stone aggregate) as in sub base complete all as specified and directed.

M &L Machine pressed precast concrete interlocking paver block of any shape & size With grey cement and no pigments confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade and including 25mm thick sand cushion complete all as specified and directed.

M & L for PCC solid blocks, kerb stones of size 300 x300x 150 mm factory made of PCC(1:2:4) type B-1 using 20 mm graded stone aggregate as in kerb stone set in CM 1:4. complete all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of primer on new concrete or plastered surfaces incl preparation of surfaces as on kerb stones complete all as specified and directed..

S & F Plate rack of size 900mmx750mmx250mm fabricated out of 1mm thick stainless steel sheet fixed in repair complete all as specified and directed.

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering complete all as specified and directed.

S & F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F steel windows factory made, out of MS hollow section 79mmx39mmx1.6mm thick frame with double shutter (glazed & welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F Steel ventilator with top hung shutter with out glazing bars to receive wire gauge etc including hinges steel peg stay etc complete incl taking down old ventilator complete all as specified and directed.

S&F 3mm thick froasted glass pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

Cutting holes into or through cement concrete slabs, chajjas etc reinforced or otherwise superficial area not exc 100 Sqcm complete all as specified and directed.

M&L Cutting holes in stone masonry walls in cement mortar & making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required superficial area exc 150sq. cm but not exc 400 sq. cm complete all as specified and directed.

S&F PVC (SWR) 50mm bore pipe single socketed in any length with rubber ring joints fix to wall complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1 (20mm graded stone aggregate) as in man hole covers, landings etc set in cm 1:4 complete all as specified and directed.

M & L for Terrazzo tiles 25cm x 25cm x 20mm thick, with size of chips upto 12 mm; set,with grey cement and pigment jointed and pointed in neat cement slurry in floors, and cut and polished including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S & F in repair 75 mm long door stopper of stainless steel body with two number rubber shoes complete all as specified and directed.

Cutting grooves in brick wall/stone wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Chipping of unsound weak and cracked concrete/cover of reinforcement over RCC member or as per site requirement by chieseling and disposal of malwa from site as per instruction of Engineer-in-Charge. (Notes : Rates incl for wk carry out G+1 floor in quoted rates)

Cleaning of exisiting reinforcement with wire brush/rotary wire brush to make surface free from rust scales, loose material, diet etc, complete and proving, applying two coats of alkline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and forma corroson resistant, insoluable and adherant protective layer, including cleaning the reinforcement, wire brushing to remove the rust spalls, with time interval of 1 hour between the coats complete all as specified and directed. (Notes : Rates incl for wk carry out G+1 floor in quoted rates)

Providing and application of corrosion inhibiting impregnation coating, designed for use as an impregnation for protection of steel reinforcment within unexposed concrete with in consumption of 0.5 kg/m2. The product should be amino alcohol and inorganic combination based migratroy corrosion inhibitor for both cathodic and anodic protection complete all as specified and directed (Notes : Rates incl for wk carry out G+1 floor in quoted rates)

Providing and application of zinc rich epoxy antocorrosive protective coating for rebar corrosion protection system complete all as specified and directed

Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufactrure specification including prepartation of surface by chipping and throughly cleaning of surface complete wherever required and as per directions of Engineer-in-Charge

M & L for Rebulilding the section of damaged RCC elements to its original size on an average 15mm thickness in two layers each by providing and applying with pre-batched, polymer modified mortar of approved make having compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109: Flexural strength >= 5N/mm2 (7 days) according to ASTM C 293-79.complete all as specified and directed

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) Sliding window of area n exc. 2 Sqm :- uPVC window with having two glass sash panel inside one slider wiremesh panel all as specified in above.

Providing & Fixing Sliding window with upside openable/ Sliding shutter for window AC/Cooler of area exc 2 sqm :- uPVC windows with having openable/sliding shutters portion fix with glass with having extra frame for fixing/provisioning of window AC/Cooler with having two slider glass sash panel inside one slider wiremesh panel all as specified in above item.

M & L for WPT in sunken floors as described here under:- Sunken floor and sides up to finished floor level shall be plastered with 15 mm thick cement plaster in CM 1:4 mixed with water proofing liquid @ 150 ml per bag of cement . (ii) Preparing plastered surfaces and providing APP polymeric water proofing membrane , minimum 3 mm thick and weighing not less than 3.0 kg/ sqm of make super thermolay manufactured by STP ltd or Hyper Plas (Polyster) manufactured by M/S IWL Ltd or 'Shatiplas' (Polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyster matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or EMW Flate' of M/S Texas India Ltd) at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch , with a over lap of 75mm at the sides and 100mm at the ends sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer's instructions including preparation of surface and filling lime concrete 1:5:10 type E2 with brick bats complete all as specified an as directed Note :- (i) Polymeric membrane shall be laid in sunken floor and on sides up to finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorised applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofing liquid shall be measured and paid seperately Note : Slab area only will be measured for payment purpose.

Taking down carefully surface aluminium or copper point wiring with PVC casing or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls, floors, etc all as directed.

Taking down celing fan of any size, sealing cable end , dismantling blade and removing fan regulator any type & size and keepinig in safe custudy for reuse/deposite to MES store all as specified and directed by Engr-in-Charge .

Refixing of ceiling fans after required minor repairs such as replacement of capacitor,connector block, split pin nuts bolts etc and connecting up including provisioning of cable from ceiling rose or connector to fan and painting of ceiling fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler , one coat after cleaning or dust etc complete.

Taking down exahust fan of any size, sealing cable end , dismantling blade and removing fan regulator any type & size and keepinig in safe custudy for reuse/deposit to MES store all as specified and directed by Engr-in-Charge .

Refixing of exahust fans after required minor repairs such as replacement of capacitor,connector block, splite pin nuts bolts etc and connecting up including provisioning of cable from ceiling rose or connector to fan and painting of exhaust fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler , one coat after cleaning or dust etc complete all as directed.

Taking down and dismantling , servicing & refixing geyser including connected accessories such as PVC connection pipe and etc of any type or make,safely and refixing after oiling, greasing and servicing in serviceable condition duly painted by synthetic enamel paint of existing colour of the same colour complete including provn of New PVC connection of appropraite size all as specified and directed including writing MES Nos. Note:- Items replaced will be included in quoted rate.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green), concealed in wall, drawn into and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes for mounting switches, sockets, fan regulator as required for one light point controlled by one switch.

All as per item No. 178 here-in-before but one fan point controlled by one 6A switch

All as per item No. 178 here-in-before but one Exh fan point controlled by one 6A switch

All as per item No. 178 here-in-before but one light point controlled by two, two way 6A switch.

All as per item No. 178 here-in-before but One socket outlet 6 amp controlled by one 6A switch on same board with other switches.

All as per item No. 178 here-in-before but One socket outlet 6 amp controlled by one 6A switch on indepdendent board.

All as per item No. 178 here-in-before but One bell point controlled by on bell push button.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board. Note :- (a) The cost of Modular Metal flush box & modular cover plate colour and size as required at site and cutting chases in stone masonary and making good disturbed surfaces using CM 1:3 shall deemed to be included in quoted rate and the make of modular plate shall be of the same brand as per Switch/Socket accessories (b) Modular switch/socket accessories shall be measured & paid separately in respective item

S&F angle holder 6A, 240V insulated polycarbonate body with back plate complete:

S&F switch modular 1 way 6/10 Amps, 230 volts, 1 module.

S&F modular socket 6/10 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular switch 1 way 16/20 Amps, 230 volts, 1 module.

S&F modular socket 16/20 Amps, 2/3pin combined 2 module AC 230 volts.

S&F modular fan regulator 120 watts, 2-module AC 230 Volts.

S&F switch modular 2 way 6/10 Amps, 230 volts, 1 module.

S&F Modular bell push 6A 1 module

S&F musical bell, AC, 230 volts, single pole.

S&F ceiling rose 3 pin(phase,neutral and earth polycarbonate body complete.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper cable of size 2 x 6 sqmm drawing into and including rigid non metallic PVC conduit concealed in wall, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fitting and fixing accessories and 6 sqmm FRLS multistranded copper conductor cable as continuous earth wire complete all as specified and directed (Note1 :- 2 runs of 6 sqmm copper wire and 1 run of 6 sqmm copper earth wire alongwith PVC conduit shall be measured as 1 unit. Note2- Rate of Cutting chasing of exixting wall and making good of disturbed surface for concealed conduit shall be included in this item

S&F 20 amp, single pole and neutral socket outlet with 2 pole and earth, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with chained metal cover for socket outlet with and including one number single pole 'C' series MCB 20 amp as required.

S&F MCB distribution board, powder coated, SPN , 240 volts, 8 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 200 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required .

S&F MCBs SP of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp.

S&F MCBs SPN of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of double pole 40 to 63 amp as specified and directed by Engr-in -Charge.

S&F in repair LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having lumen not less than 2200 complete all as specified and directed.

S&F in repair LED(0.6M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having lumen Upto 100 lumens per watt complete all as specified and directed.

S&F LED 35 watt building security light smartbrite aluminium PDC housing with IK 07 protection PC glossy diffuser duly prewired connection having a nominal system lumen output of efficiency 100 lumens/ watt light watt and total power consumption not more than 35 watt including driver. It has a rated IP 66 with 5 KV inbuilt surge protectione. (Note:- Bracket along with screw to fix on wall/surface duly painted by silver colour paint will be included in above quoted rate.)

S&F PVC fresh air fan 200/250 mm sweep,230 V with louvers, fan motor and accessories complete including making connections.

S&F surface mounted LED panel with opal diffuser and separate Electronic driver for 12 watt, 240V, slim compact aluminium die cast edge lit panel, 6500K 1200 lumen output having luminous efficacy.

S&F in repairs 9/10 Watt Bulk Head light environfriendly ultra modern energy saving surface mounted decorativeoval bulk head edge lit LED luminaire comprising of High brightness LED Lamp.

Supply, installing ,testing and commissioning Stationary storage type electric water heater( geyser) 25 ltr capacity BEE 5 star rating inbuilt current leakage protection device, multifunction safety valve, high precision thermostat control,Preset thermal output, high working pressure 0.8 MPa,vertical mounting including min 2 yrs warrenty.

S&F ceiling fan type 1200 mm sweep 50 Hz AC 230 volts, BEE 5 star rated in white colour with fan motor, blade set , 0.45 mtr down rod, canopy.

Schedule of Credit