Construction of Balance work of Medical and Paramedical Staff Quarters for District Hospital Ramban.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth, 1.5mtr in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.50m disposed earth to be leveled and neatly dressed. (a) All kinds of soil

Disposal of surplus earth by M.T. upto 5 Km

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-All work upto plinth level in 1:4:8 (1 cement: 4 coarse sand: 8 crushed graded stone aggregate 40mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-All work upto plinth level in 1:4:8 (1 cement: 4 coarse sand: 8 crushed graded brick aggregate 40mm nominal size).

Stone soling beneath floors in parking area

Sand filling beneath floors

Providing and laying in position cement concrete of specified graded excluding the cost of centering and shuttering - All works upto plinth level 1:1.5:3 ( 1 cement: 1.5 Coarse sand: 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement. (a) 1:1.5:3 ( 1 cement: 1.5 coarse sand: 3 graded crushed stone aggregate 20mm nominal size).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

Coulmns, pillars, piers, abutments, posts and struts.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, griders, bressumers and cantilevers.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50M and lift upto 1.5 M.

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. (a) 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) crushed.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed, consolidating and grouted with fine sand including finishing the top smooth.

Brick masonry with bricks of class designation 75 in foundation, plinth and superstructure above plinth level upto floor V level. (By manual means) plinth in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure above plinth level upto floor V level. (By manual means) plinth in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing wood work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). 2nd class deodar wood.

Providing and fixing 35mm thick panalled or panalled and glazed shutters for Doors, Windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws excluding panelling which will be paid for separately, all complete as per direction of engineer-in charge in 2nd class deodar wood.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel insert excluding portion inside grooves or rebates to be measured). Panelling for panelled shutters 12 mm thick water proof ply.

Providing and fixing 35 mm thick glazed shutters for doors, windows and clerestory windows using 10kg/sqm (4mm thick) float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws in 2nd class deodar wood.

Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both direction with wire of dia 0.63 mm for doors, windows and clerestory windows with hinges and necessary screws in 2nd class deodar wood.

Providing and fixing 20mm dia heavy type nickel plated M.S. pipe curtain rods with nickel plated brackets.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats square or round bars etc. including priming coat with approved steel primer all complete. (a) fixed to openings/ wooden frames with rawl plugs screws etc.

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 (1 cement:3 coarse sand: 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coated not less than grage AC 10 as per IS: 1868) transparent or dyed to required color or shade with nuts and screws etc. complete.

Providing and fixing aluminum tower bolts ISI marked (anodised anodic coated not less than grade AS 10 as per IS: 1868) transparent or dyed to required color or shade with necessary screws etc. complete.

Providing and fixing aluminium handles ISI marked anodised ( anodic coated not less than grade AC 10 as per IS: 1868) transparent or dyed to required color and shade with necessary screws etc. complete.

Providing and fixing single rubber alumium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (a) size of tile 60x60cm NITCO, ORIENT,SOMANI, KAJARI.

Providing and laying of 80mm thick factory made cement concrete interlocking paver blocks of M-30 grade-ISI marked, IS-15658 made by block making machine with strong vibratory compaction and of approved size and design/shape, laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with course sand, locking at end with concrete etc. all complete as per direction of Engineer in-charge.

Providing and fixing ceremic antiskid floor tiles 300x300 mm (thickness to be specified by the manufactures)of Ist quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in color such as white, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of cement mortor 1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Providing and fixing Ist quality ceremic glazed wall tiles conforming to IS: 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all color, shade except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortor 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Flooring/dado with 18 mm thick polished granite stone (sample shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with grey cement slurry complete. (a) (Safdar Ali) Granite stone.

15 mm thick cement sand plaster of mix: 1:4 ( 1 cement : 4 fine sand) in ceiling

15 mm thick cement sand plaster on the rough side of single or half brick wall of mix: 1:6 ( 1 cement : 6 fine sand)

20mm thick cement sand plaster of mix (Exterior) (a) 1:4 (1 cement : 4 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture including priming coats with water thinnable cement primer on walls.

Providing and applying wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete (ceiling only).

Painting with ready mixed synthetic enamel paint on new steel work (two or more coats) of approved brand and manufacture in all shades to give an even shade.

Providing and applying exterior paint with APEX Paint to required shade and approved quality as per direction of Engineer-incharge including a coat of primer and make good the surface with putty complete.

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved branded and manufacture of required color to give and even shade. Two or more coats on new work of approved brand and manufacture (wood work) including preparation of surface complete.

Providing corrugated G.S sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required 1.63 mm thick with zinc coating not less than 275gm/sqm.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I limpet and bitumen washers complete. (0.63mm thick with zinc coating not less than 275gm/sqm.

Strctural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 8 mm thick 1800x1200 mm calcium silicate Board false ceiling at all height including providing and fixing of frame work made of special section, power pressed from M.S. sheets and galvanized with zinc coated of 120 gms/sqm (both side exclusive) as per IS: 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm at 1200 mm C/C, the flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangess of 25 x 10 x 0.50 mm of required length with nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45 x 15 x 0.90 mm running at the spacing of 1200 mm C/C, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm C/C, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clip made out of 2.64mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.50 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partitions with the help of Raw plugs at 450 mm centre with 25 mm long dry wall screws @ 230 mm interval, including fixing of calcium silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x 25 mm at 230 mm C/C, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering upto 150 mm on both sides of joints and two coats of primer suitable for boards, all as per manufactures specification and also including the cost of making opening for light fittings, grills, diffusers cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specifications and direction of the Engineer incharge but excluding the cost of painting work.

Providing and fixing of superior quality ACP sheet in lining/partitions/ front facia work in panels fixed over frame work of aluminium standrad sections with necessary nuts, bolts, screws, brackets, suspendors well-connected and anchored with masnory walls. All complete as per architectural drawings and the directions of Engineer-in-charge.

Providing and fixing of white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white P.V.C flush cistern with manually controlled device (handle level) conforming to IS: 7231, with all fittengs and fixing, complete including cutting and making good the walls and floors whenever required:

W.C pan with ISI marked blacks solid plastic seat and lid.

Providing and fixing wash basin with C.I/M.S. brackets, 15mm C.P. brass taps, 32mm C.P. brass waste of standard pattern, including painting of fittengs and brackets, cutting and making good the walls whenever required:

White vitreous china wash basin size 630 x 450 mm with a pair of 15mm C.P brass pillar taps.

Providing and fixing G.I inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing white vitreous cement china pedestal wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete:

Semi rigid pipe 40mm dia

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls whenever required

Stainless steel kitchen sink of size 600x450x250mm.

Providing and fixing 100mm C.P. grating for gully, floor or nahani trap.

Providing and fixing in position 25mm diameter mosquito proof couping of approved municipal design.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard.

Rectangular shape 600x450mm

Providing and fixing 600x120x5mm glass shelf with edge round of supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc. complete.

Providing and fixing toilet paper holder C.P. brass.

Providing and fixing soil, waste and vent PVC pipes. 110mm dia PVC

80mm dia PVC

Providing and filling the joints with PVC solution and seal complete. 110mm dia pipe

80mm dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to PVC pipes. For 110 mm dia. Pipe.

For 80 mm dia. Pipe.

Providing and fixing PVC bend of required degree with acess door, insertion rubber washer 3mm thick, bolts and nuts complete. 110mm dia

80mm dia

Providing and fixing plain PVC bend of required degree. 110mm dia

80mm dia

Providing and fixing heel rest sanitary bend: 110mm dia PVC

80mm dia PVC

Providing and fixing single unequal PVC junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

110x110x110mm dia PVC

80x80x80mm dia PVC

Providing & fixing single unequal PVC junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

110x110x110mm dia PVC

80x80x80mm dia PVC

Providing and fixing single unequal plain PVC junction of required degree with acess door, insertion rubber washer 3mm thick bolts and nuts complete.

110x110x80mm dia PVC

Providing and fixing single unequal plain junction of required degree. (PVC)

Providing and fixing PVC off-sets. 110mm dia

80mm dia

160mm dia

Providing and fixing PVC terminal guard: 110mm dia

80mm dia

Providing and fixing PVC collar: 110mm dia

80mm dia.

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or with or without vent arm complete, including cost of cutting and making good the walls and floors:

110mm inlet and 110mm outlet

110mm inlet and 80mm outlet

Cutting chases in brick masonry walls for following diameter PVC pipes and making good the same with cement concrete 1:3:6 ( 1 cement: 3 coarse sand: 6 graded stone aggregate 12.5mm nominal size) 1:4 ( 1 cement: 4 coarse sand)

110mm dia.

80mm dia.

Providing and fixing towl ring with a minimum distanceof 37mm from wall face with concealed fittings arrangements of approved quality and color, weighing not less than 88gms.

Providing and fixing towl rail complete with brackets fixed to PVC creats with CP brass screws with concealed fitting arrangement of approved quality and color.

450mm long towl rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms.

600mm long towel rail with total length of 645mm, 78mm wide and effective height of 88mm, weighing not less than 190gms.

Providing and fixing glass shelf of approved quality and colour.

Providing and fixing G.I pipes complete with G.I fittings and clamps, including cutting and making good walls

15mm dia nominal bore (medium)

20mm dia nominal bore (medium)

25mm dia nominal bore (medium)

Providing and fixing G.I pipes complete with G.I fittings and clamps, trenching and refilling etc. (external work)

20mm dia nominal bore.

25mm dia nominal bore.

40mm dia nominal bore.

Making connection of G.I distributing branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.and making long screws etc. complete.

25 to 40mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8391 15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15mm nominal bore

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS: 8931

15mm nominal bore

Providing and fixing C.P. brass angle value for basin mixer and geyser points of approved make conforming to IS: 8931

15mm nominal bore

Providing and fixing C.P. brass close hole basin mixer pillar tap of approved quality and make conforming to IS: 8931

15mm nominal bore

Providing and fixing brass stop cock of approved quality. 15mm nominal bore

20 mm nominal bore

Providing and fixing gun metal gate value with C.I. wheel of approved quality (screwed end)

25mm nominal bore

40 mm nominal bore

Providing and fixing ball value (brass) of approved quality complete. High or low pressure with plastic floats.

20 mm nominal bore

Providing and fixing gun metal non-return value with of approved quality (screwed end)

15mm nominal bore (horizontal)

Providing and fixing unplasticised PVC connection pipe with brass unions 15mm nominal bore

20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20mm inlet 100mm diameter

Providing and fixing C.I. sluice value (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately)

100 mm dia. Class I

Constructing masonry chamber 30x30x50 cm, inside with 75 glass designation brick work in cement mortar 1:5 (1 cement: 5 fine sand) for stop cock, with C.I. surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) necessary excavation, foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design (with F.P.S bricks)

Crushed

Constructing masonry chamber 90x90x100 cm, inside with 75 glass designation brick work in cement mortar 1:5 (1 cement: 5 fine sand) for sluice value, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and R.C.C. top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortor 1:3 ( 1 cement: 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design. (with F.P.S bricks)

Crushed

Providing and filling sand of coarser grade all around the G.I. pipes in external work 20mm dia. Pipe

25mm dia. Pipe

40mm dia Pipe

Providing and fixing G.I. union in G.I pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15mm nominal bore

20mm nominal bore

25mm nominal bore

40mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and make necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (sintex, Electroplast, Star, Lotus or equivalent having valid ISI license)

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4, C.I. cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame not less than 38kgs, R.C.C. top slab with 1:2:4 mix, foundation concrete 1:5:10, inside plastering 12mm thick with cement mortar 1:3, finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.

Inside dimension 455x610m and 40cm deep for single pipe line with common burnt clay bricks

Excavating trenches of required width for pipes, cables. All kinds of soil-(a) pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia.

Cutting holes up to 15x15cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size), including finished complete so as to make it leak proof.

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Making hole up to 20x20 cm and embedding pipes up to 150mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement: 3 coarse sand 6 graded stone aggregate 20mm nominal size) including disposal of malba.

Providing laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete.

150mm diameter

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) aii-round S.W. pipes including bed concrete as per standard design:

150mm diameter S. W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and fixing C.I. cover without frame for manholes: 455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Supplying and fixing C.I. cover 300x300mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg

Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete 150mm dia.

Providing installation and testing of Geyser of approved quality and manufacture Venus/Bajaj or equivalent mounted on boltd, well anchored in wall and connected with hot and cold G.I. connection with superior angle values as required:

35 litres capacity

20 litres capacity

Construction of septic tank (over all external dimension 28'-00" x 11'-6") complete with earth work cutting/dressing, de-watering operation, laying of 6" thick soling followed by 3 inch thick P.C.C. 1:4:8 mix and laying of R.C.C. raft/floor, external/baffle walls and top covered with R.C.C. 6" thick slab with provision for 02 openings 2'-6" x 2'-6" and positioning of inlet/outlet pipes, cement plastered externally and internally smooth cement finished with 1:3 mix complete as per design/drawing approved.

Construction/making of soak pit complete with earth work cutting, dewatering operation bottom clear dia 7'-4" and top dia 10'-0". Foundation well dressed laid with 6" thick stone soling followed P.C.C. 1:4:8 and R.C.C. raft 6" thick. Dry stone masonry walling externally with R.C.C. bands 6" thick at 4'-0" interval. Top covered with R.C.C. slab 6" thick with provision for opening 2'-0" x 2'-0" and positioning of inlet pipe complete as per design/drawing approved.

Construction of water reservoir capacity 10000 liters complete with earth work cutting, de-watering foundation well dressed laid with 6" thick stone soling followed by PCC (1:4:8) with RCC walls externally (internal size 8'-0" x 5'-9") top covered with RCC slab 6" thick with provision for opening 2'-6" x 2'-6", positioning of inlet pipes complete cement plastered externally and smooth finished with cement mortar 1:3 complete as per design/drawing approved.

A B ENTERPRISES