SPL REPAIR WORK TO BLDG NO P-5 RADIOLOGY DEPT OF GH AND PROVN OF GENERATOR SET (80/82.5 KVA) TO PROVIDE GENERATOR BACK UP AT GH UNDER GE (EAST) FEROZEPUR CANTT

Amount

BR WORKS Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and as directed.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, bed blocks,back filling in chowkhats, benching etc including necessary form work complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and as directed.

M&L for 40mm thick Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in floor topping, surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for 50mm thick Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in sub base of flooring,surface finished rough to receive floor topping complete all as specified and directed.

Dismantling floor hearth or wall/stone tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),premium quality area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including screed bedding 15mm thick in cm(1:6), complete all as specified and as directed.

M&L for Glazeded ceramic coloured (colour & shade as approved) tile 350x250x7 mm/450x300x7mm thick in vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles 300 X 200X 7 mm thick in vertical surfaces set and jonnted in cement slurry and pointed in white or colour cement to match over and including 10mm thick back coat in CM 1:4 complete all as specified and directed.

M&L for Vitrified ceramic tile Light shade 8 to 9 mm thick (square or rectangular) polished area of each tile not exc 0.36 SM in floors etc., set and jointed in neat cement slurry and pointed in white cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Granite (of any type) tiles18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 10 mm thick plaster as in back coat CM 1:4 complete including making circular gas pipe hole, moulding at corners and polishing type complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Dismantling of brick tiles single layer laid on roof jointed & pointed in cement mortar complete all as specified and as directed.

Demolition of mud in roofs, any thickness, including plastering and leaping etc complete all as specified and as directed.

M&L for Rendering/ plastering 10 mm thick on roof surfaces in cement mortar 1:3 finished fair and even without using extra cement complete all as specified and directed.

M&L for Polythene film 150 micron thick laid on roofs with 150 mm overlaps including a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm complete all as specified and directed.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and directed.

M&L 80 mm thick average consolidated thickness mud phuska on flat roofs including 25 mm thick mud plaster etc complete all as specified and directed.

M&L for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and directed.

All as per srl item No 20 here-in-before but using old brick tiles retrieved from dismantling (Item No 14 here-in-before) including cleaning and removal of mortar from tiles complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches, pillars etc complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in c:m 1:6 complete all as specified and directed.

All as per srl item No 23 here-in-before but using old bricks retrieved from dismantling under ser item 22 here-in-before including cleaning and removal of mortar from old bricks etc complete all as specified and directed.

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering/ plastering 12mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for Rendering/ plastering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for Rendering/ plastering 10 mm thick in cement mortar 1:4 on ceiling surfaces finished fair and even without using extra cement complete all as specified and directed.

M&L for Preparation of new plastered surfaces of ceiling & applying two coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls etc.and applying three coats of white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls etc., and applying two coats of cement base paint complete all as specified and directed.

M&L for Complete removal of existing treatment including preparation of surfaces of walls & applying two coats of cement base paint complete all as specified and directed.

M & L for complete removal of existing treatment over wall and applying two coats of distemper oil emulsion over and including 2mm thick wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying 2 coats of distemper oil emulsion overand including 2mm thick wall care putty complete all as directed of any shade on walls surfaces complete all as specified and directed.

M&L for Complete removal of existing treatment including preparation of surfaces of walls & applying two coats of white wash complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise as directed complete all as specified and directed.

All as per srl item No 38 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and as directed.complete all as specified and directed.

Taking down shutters of any description,exc.1.0 sqm and not exc.2 sq. m each and after repair refixing in same opening complete all as specified and directed.

Taking down shutters only of any description exc 1 sqm and not exc 2 sqm each including removing from site to store or otherwise as directed complete all as specified and directed.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed.

S&F 30mm thick, Flush shutters, solid core construction, with partical board core, commercial type on both sides,one face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed.

S&F 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/ 08.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/ 08.

S&F Steel windows or ventilators, fixed type, with glazing bars including one shop coat zinc chromate primer complete all as specified and directed.

M&L for Mild steel framed work conforming to Fe 290. Gde E-165 as in grills/guard bars shouldered with steel window/ ventilator frames including red oxide primer coat complete all as specified and directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain / coloured PVC "C"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement complete all as specified.complete all as specified and directed.

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide priming complete all as specified and directed.

M&L for Preparation of primed steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M& L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M& L for Preparation of old decorated surface of steel and iron of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F alluminium anodised handles 150 mm long fixed to doors complete all as specified and directed.

S&F alluminium anodised tower bolts 200 mm long fixed to windows complete all as specified and as directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and directed.

S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

All as per ser Item No 65 above but fixed in repairs.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per ser item No 69 here-in-before but 20 mm bore tubing.

M&L for GI steel water tubing, 15mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified and directed.

All as per ser item No 71 here-in-before but 20 mm bore tubing.

Fixing only,after cleaning old steel water tubing,15 mm bore and connections in new or old position using new fittings complete all as specified.complete all as specified and directed. ( Note:- serviceable pipes obtained from item 69 to be reused).

All as per item No 73 here-in-before but 20 mm bore ( Note ;- Serviceable pipes obtained from item 70 to be reused).

S&F in repair stop valves, fancy type, CP with long shank and cup ( concealed type ), screwed both ends for 15mm bore of iron pipe or for union and fixed complete all as specified and directed.

S&F in repair piller taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed complete all as specified and directed.

S&F in repair Gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair Gunmetal gate valve of 15mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F brass CP Angle cock with long shank/flange and cup (concealed type) 15 mm dia bore screwed down with crutch handle both end screwed for iron pipe or union as fixed in repairs complete all as specified and as directed.

S&F in repair PVC waste pipe 32 mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks / WHBs/Urinal complete all as specified and as directed.

S&F in repair Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and as directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified and directed.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe incl dismantling existing water storage tank complete all as specified in SSR Part-I complete all as specified and directed.

S&F in repair Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.

S&F Vitreous china wash down water closet pan ( pedestal pattern ), white/ coloured including seat & cover, flush pipe,health faucet connection to drain and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.

S&F in repair PVC 10 litre capacity . valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed.

S&F in repair Pedestal pattern Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified and directed.

S&F in repair central hole basin mixer for wash hand basin including all fittings ie including connection pipe as per manufaturers specification complete all as specified and directed.

S&F 15mm dia CP Sink cock swan neck regualar spout with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 1mm thick stainless steel sink with dranage board, plugs, washers, PVC waste pipe, union, CP cuppling & cantilever brackets embedded in cement and sand mortar in wall, overall size 915mmx460mm bowl size 410mmx330mmx160mm as in repair complete all as specified and directed.

S&F in repairs urinal flat back Vitereous china(white) ,of size 465x365x265 mm with grating union for discharge pipe,spreader & 40mm dia PVC waste pipe up to floor trap complete all as specified and directed.

S&Fin repair PTMT grating doom 100mm dia with or without waste hole fixed in repairs complete all as specified and directed.

S&F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified and directed.

S&F Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs,in repair complete all as specified and directed.

Taking down eaves gutters and rain water pipes( any size or pattern),including all fittings heads shoes bends swan-necks etc complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed to walls or laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm dia Junction single (Single or double T) equal or unequal complete all as specified and as directed.

S&F 110mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc., complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets,end cups,rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified and directed.

M & L for applying bond coat of epoxy bonding agent & cement in 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additives upto 60mm thickness (Chajjas fins, border etc) (i) Qty of ploymer to be used 15% by weight of the cement. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repear this step after 24 hrs as required.(iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as specified and directed by Engineer-in-CHarge. Make : - Epoxy bonding agent shall be Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as directed by Engineer-in-Charge

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid bedded , dry and pointed etc. complete all as specified and as directed.

M & L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, jointed and pointed with gray cement and no pigment over and including 25mm thick layer of sand cushioning complete all as specified and directed.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for ( reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L Reinforced cement concrete nominal mix (1:2:4),type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) rough surfaces of concrete complete all as specified and directed.

S&F mild steel TMT bars as in reinforcement 10mm dia and over cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F Powder Coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder Coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed. Note:- (i) Aluminium chowkhat /frame, glass,wiremess and aluminium grill shall be measured and paid separately.

S&F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

S&F Powder Coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with pproved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction.

Supply and fixed in repair hydraulic door closer of aluminium die cast body,designation No-3 universal type suitable for door shutter of 851 mm to 1000 mm weight between 61 Kg to 80 kg, etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass mortice lock 75 mm, 2 levers, vertical type complete all as specified and directed.

Dismantling wall and ceiling boards(fibre,pulp,insulation,etc.) or insulation boards/slabs/blanckets, any thickness,including cover fillets complete all as specified and directed.

Material and labour for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

Material and labour fancy designed 6 mm thick exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (frame work for ceiling shall be measured and paid separately) fixed to GI frame work in ceiling and all other similar works complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification & drawing complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F 18mm thick Prelaminated particle board,flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade, prelaminated both side with decorative choice lamination, fixed with screws as in shutters & shelvesincluding 6mm thick teak wood leaping on three sides and 20mm thick on hanging side complete all as specified and directed.

Dismantling timber scantling unframed work as in fillets, rails, posts, rafters, purlins,etc under 40 Sq.cm in section complete all as specified and directed.

M&L in repair for Plain fillets of 2nd class hard wood, square or rectangular or triangular in section, clean sawn, secured with nails and brads area n exc 3 Sq cm complete all as specified and directed.

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

E/M WORKS Taking down carefully existig copper / alumn point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, c/ rosess, holders and bracket fittings with battens / conduits / wires,T/L fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following : (a) One light/fan/bell/Bldg security light point controlled by one single pole one way switch. Note:- wiring shall be done in colour coding

All as per item No 132 here in before but One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board.

All as per item No 132 here in before ) but One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

All as per item No. 132 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed,stranded copper conductor cable.

All as per item No. 132 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC insulated,stranded,unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC insulated, unsheathed,stranded copper conductor cable.

S&F 6 amps, single pole, one way switch urea back piece (IP20), 240V, 50Hz, white in colour, duly ISI marked complete all as specified and directed.

S&F Switch piano flush type 20 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

S&F 6 Amps Socket 2 in 1, Urea backpiece (IP20), white in colour, duly ISI marked complete all as specified and directed.

S&F Socket outlet, UNI, 2 in one 10 Amps & 20 Amps, white in colour, duly ISI marked complete all as specified and directed.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F batten holder (with metal ring), 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed. Make- Anchor/ Cona/ Plaza.

S&F rotary stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, deluxe, white in colour, duly ISI marked complete all as specified.

Supply and fixing LED light fitting 1 x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulb of 9/10 watts B-22 CDL 3 star 6500K, complete all as specified and directed.

S&F Factory made three phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 125 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning complete all as specified and directed.

M&L for Sub main wiring with two single core 2x6 sqmm FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn in and including FRLS rigid conduit connected to main board complete all as specified and directed. (Note:- Two runs cable and one number earth wire and suitable FRLS conduit shall measured together as unit length).

S&F exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.

M&L for Cutting hole for grouting nuts & bolts for fixing of exhaust fans, making good, the disturbed surface to match with the existing surface complete all as specified and directed.

Fixing or hanging only ceiling fans height upto 3mtr to 5 mtrs ceiling height of bldg including three core FR PVC Insulated & overall round sheathed flexible with PVC, colour of cores are Red, Black & Yellow/ Green is for earthing. Sheath colour is Black of cable size 23/0.0076 complete all as specified. Note : Ceiling fans obtained/ taking down from item Sr No.129 above shall be reused.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

Supply & fixing Single pole & Neutral Sheet metal enclosure with a two pin and earth plug Top and socket complete with one Double pole MCB of 32Amps

M& L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.3 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to sxposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified and directed. ( Note:- Excavation & earth work, cable protection shall be measured and paid separately.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan, for laying of cable and getting out, complete all as specified and directed.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified and directed. Note- Punned down thickness shall be measured.

S&F Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified and directed.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified and directed.

S&F Mild steel galvanised pipe, light grade, 50 mm nominal bore for passing of cable, fixed to poles/walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 core complete all as specified and directed.

Material & labour earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth electrode GI strip 32 x 6mm dia connected to GI earth plate electrode by means of bolts, nuts, check nuts and washers of galvanized iron and thimbles and other end of earth wire connected to main switch board and protected by galvanized iron light grade 40mm bore and GI pipe 20mm bore medium grade with funnel and wire mesh for watering including necessary excavation and earth works. PCC chamber in cement concrete (1:3:6) type C-2 using graded stone aggregate and RCC cover in M-25 (Design mix) and all as shown in Electrical Plate No. 3 of MES Schedule (Part-I) of 2009 complete all as specified and directed.

Supply, installation, commissioning and testing of eco-friendly Static type Diesel Engine driven generating set silent type confirming to CPCB condition/norms, 82.5 KVA 415 volts (AC 3 phase,4 wire system of supply) 50 Hz at 0.8 power factor directly coupled alternator & engine, water cooled, mounted on common base plate of rigid fabricated mild steel frame platform with floor mounted fuel tank and including excavation, earth work, PCC foundation plateform as per DG set OEM manufacturing drawing, anti vibration pads/ dampers including standard control panel other accessories as per manufacturer's design.The Gen set should be fitted with integrated accoustic enclosure manufactured by the OEM of the Generating set .The Generating Set and accoustic enclosure shall confirm to emmision norms and noise level.The accostic enclosure shall be type tested and certificate obtained for the type approved from approved agencies listed in Govt Notification.Specifications of DG set shall be as specified and and comprising of the following:-

item 167 Contd... (A) ENGINE (Prime mover) : Diesel engine vertical type of adequate capacity for 82.5 KVA ,1500 RPM (conforming to IS: 4722/BS:5514) of suitable BHP as per manufacturer recommendation,Turbo charged water cooleed ,12 volts electric battery start, complete with fly wheel and all standard fittings/fixtures as per manufacturer instructions including suitable engine control panel/dash Board with electronic techometer.Lubrication oil temperature & pressure gauges water temp gauge and frequency meter (digital type) including safety automatic shut down in case of fault such as high water temperature low oil pressure,over speed etc including self starter,alternator,coggedV belt,fuel tank with first fill of lub oil and coolant(as applicable) etc complete all as specified.

Item 167 Contd.. (B) ALTERNATOR: Aternator AC ,3 phase 415 volts 4 wire rated line current for output 82.5 KVA,PF 0.8 1500 RPM confirming to BS 5000/ IS 4722. Insulation class enclosure/SPDP self excited, self regulated brushless, complete with AVR with +1% voltage regulation directly coupled with above engine. (i) Anti vibration pads for mounting engine and alternator assembly on the base frame/plate or as recommended/provided by the manufacturer (ii) Base frame made out of structural steel as per manufacturer's recommended. design/specifications.

Item 167 Contd.... (C) ACCOUSTIC ENCLOSURE Provision of an integral type approved/certified acoustic enclosure. It shall be made of 16 SWG or manufacturer's standard norms out of CRCA sheet with powder coated finish on outside and provided with non igniting fire retardent foam as acoustic material of suitable thickness and perforated sheet of stainless steel as per manufacturer design.The doors and glass window shall be as per manufacturer's design.The base frame shall be of ISMC.It shall also include the following:- (i) Silencer: Suitable exhaust Residential grade silencer to reduce the noise level. (ii) Internal wiring with PVC copper cable (ISI 694marked) FRLS in conduit and for light and fan point lamp fittings including lamp. (iii) Fuel tank: Sub Base Fuel tank of 14 SWG MS sheet of capacity considered as per OEM duly powder coated. (iv) one Nos 12V x 88AH maintenance free batteries as recommended by manufacturer.

M/s Harkesh Kumar Bansal

ABHISHEK AND COMPANY