CA NO. GE (I) (AF)/SHL/ 2022-23 CERTAIN REPAIR TO JOINERY, WALL PLASTERING, ROOF, CEILING, FLOOR/WALL TILES, PLUMBING, PLINTH PROTECTION AND MISC WORKS TO CERTAIN BUILDINGS OF SMQ AREA ZONE-A AT HQ EAC (U), UNDER GE(I) (AF) SHILLONG

Amount

Note : All unserviceable materials obtained out of demolition/dismantling/taking down (other than those for which credit catered under Schedule of credit) shall be disposed of outside MoD Land. Quoted rates against respective item shall deemed to include for same.

B/R ITEMS Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material complete all as specified directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position complete all as directed.

Dismantling wrought iron, or mild steel work of any description not otherwise provided for complete all as directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area not exc. 1 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area exc. 1 sqm & n.exc 2.00 sqm each complete all as specified and directed.

Dismantling plain or corrugated steel sheeting/galvalume sheet any guage, thickness including Nainital or similar pattern roof covering,complete all as specified and directed

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as directed.

Taking down existing roof treatment including PCC padding over roof, removing complete layer of bitumen under PCC padding, cement mortar & felt cleaning the surface by hacking to receive plaster and removing demolished material outside MD land complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles in flooring, apron etc of any description or thickness laid, bedded and pointed in any mortar complete all as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beeds complete all as specified and directed.

Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site complete all as specified and directed .

Dismantling water tank of capacity exceeding 500 Ltrs but not exceeding 1000 Ltrs and removal from site complete all as specified and directed .

Dismantling of PVC(SWR) drain pipe alongwith fittings and accessories and taking out from walls, floors or from trenches, if required complete all as specified and directed for following sizes:- (Note :- The length shall be measured along the centre line including fittings and accessoires}.

75mm dia

110mm dia

M & L cutting and pinning in brick walls for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm girth but not exc 20 cm girth complete all as directed.

M & L for cutting holes into stone walls built in cement mortar or in cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 exc. half brick but not exc.one brick complete all as directed.

M & L for PCC 1:5:10 type E-2 using 40 mm graded crushed stone aggregate as in foundation, filling under floor, in sunken floors etc complete all as specified and directed.

M&L for pre-cast cement concrete block masonry 1:3:6 Type C-1 using 20mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

Supply only integral water proofing liquid complete all as directed.

M & L for second class hard wrought as in scantling framed and fixed complete all as specified and directed.

M & L for first class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads section area exc 3 Sqcm but n.exc 6 Sqcm complete all as specified and directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads section area exc 6 Sqcm but n.exc 13 Sqcm complete all as specified and directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads section area exc 13 Sqcm but n.exc 25 Sqcm complete all as specified and directed.

M & L for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and directed.

S & F in repair of 40mm thick second class hardwood (CHIR) boarding as in floors and skirting planed one side and edges tongued and grooved or rebated and fixed with nails complete all as specified and directed.

M & L for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35mm thick IInd Class Hard wood, plain framed, panelled door shutters, two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces (as ordered). The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 25mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 30mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, In opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed for following sizes:-

75 mm long.

100mm long.

S & F 100mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 150mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 100mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

M&L for 75mm size hasp and staple, mild steel safety type, stove enamelled black including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolts, plate type with bolt not less than 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as directed

S & F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S & F continuous (Piano) hinges width of flaps (when open) 30mm, MS, bright finish or electro galvanised complete all as specified and directed.

S & F ball catches with 8mm dia steel ball and brass body and skirting plate including letting in and fixed complete all as specified and directed.

S & F 20mm dia, harrison rails,anodised aluminium alloy curtainrails with fixing brackets, stops, rollers etc. complete all as specifed and directed.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S & F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S & F structural rolled mild steel confirming to Fe-410 W (Gde E-250) quality 'A' for joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

M & L for mild steel work conforming to Fe-290 Gde E-165 as in hold fast of flat iron bands, straps, supports or stays for rain water, ventilating pipes cut to length, bend to shap including bolts if required and wall tie, clamps etc., and including preparing surfaces and treated with tar and sanded with clean sharp sand complete all as specified and directed.

S & F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete con- forming to Fe.290.Gde-E-165 complete all as directed.

S & F 1.6mm thick mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as speicified and directed.

S & F 12mm dia mild steel square bar in grill or guard bars welded to steel window complete all as specifed and directed.

S & F hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters runnings bars, for doors balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including secruing bolts , posts and struts in fencing including cutting tops to shape as directed, rilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc ) including all necessary drilling, bolting or reveting etc and similar work confirmign to Fe-410-0 or Fe310-0 complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay complete all as specifed and directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm , black finish reinforced with non-woven polyester reinforcement matt, with a thermo fusable finish laid over compatible cold emulsion bituminous primer applied at the rate of 0.40 Kg/Sqm by torching with a propane or a butane gas torch, with a overlap of 75mm on longitudinal direction and 100mm on transverse direction including sealing all as per manufacturer’s instructions complete all as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 100 Gms/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

S & F for pre-painted galvalume aluminum zinc coating GI based trapizoidal profile steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions completed all as specified and directed.

S & F 0.63mm thick galvanised corrugated mild steel sheeting in with two corrugation side lap, fixed with 'L' type or cranked hook bolt using profiled GI washer and bitumen washer in roofs, walls etc with grade of Zinc coating 120 (Type-VIII) complete all as specified and directed.

S & F for 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) fixed with 'L' type or 'J' type hook using profiled GI washer and bitumen washer in roofs, walls etc Zinc coating 120 (Type-VIII) complete all as specified and directed.

Fixing only old serviceable pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet any thickness of any colour in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

S & F 4mm thick non-asbestos fibre cement building board, fixed to timber framework with screws as in ceiling complete all as specified and directed.

S & F 18/19 mm thick Prelaminated particle, board, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination and alround covered with 6mm thick teak wood beading/lipping fixed with screwed to timber frame complete all as directed.

S & F in repairs 18/19 mm thick Prelaminated particle, board, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination and alround covered with 6mm thick teak wood beading/lipping fixed with screwed to timber frame complete all as directed.

M & L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in flooring and finished even and smooth without using extra cement complete all as specified and directed.

M & L for 40mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in flooring and finished even and smooth without using extra cement complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for granite (as approved by GE in any colour) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars(fixing with clamps), window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

M & L 20 mm thick machine cut granite (of any type) work (table rubbed and polished) as in wall cladding/skirting/dado, pillars and like laid over cement screed bed and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting/bullnozing/polishing complete all as specified and directed.

M & L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM 1:4 on fair faces of brick masonry/concrete surfaces, mixed with water proofing liquid @ 150ml per 50 Kg bag of cement and finished even and smooth without using extra cement complete all as specified and directed. (Note :- Supply only Water Proofing Liquid shall be measured and paid separately)

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for treating sunken floor surfaces with two coats (one priming coat and one finishing coat) of water proofing chemical PIDIFIN 2K of Dr Fixit (or any other brand approved by GE) all as per Manufacturer's instructions complete all as specified and directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all specified and as directed.

S & F 4mm thick figured glass pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all specified and as directed.

M & L for preparing newly plastered surfaces and applying three coats of white wash on ceiling/soffits of chajjas etc complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1mm thick wall care putty complete all as directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

Material and labour for preparation of newly plastered surfaces of wall, applying a coat of 1mm thick wall care putty and applying two coats of weather proof acrylic paint over one coat of exterior grade acrylic primer complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Beger, Acroguard 3X of Acro paint.

M & L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of 1st grade quality complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for preparing surface of wood or wood based materials, new or old of any description and girth, not otherwise described and treated with creosote complete all as specified and directed.

M & L for French Polishing on new wooden or wood based surfaces of any description width or girth including cleaning and preparing the new surface including a coat of wood filler with two or more coats complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed for following sizes:-

75mm bore

110mm bore

S & F PVC (SWR) bend of any radius with oval access door complete all as specified for following sizes:-

75mm bore

110mm bore

S & F PVC (SWR) 75mm junction, single (single T) equal or unequal complete all as specified and directed .

S & F PVC (SWR) 110mm junction, single (single T) equal or unequal complete all as specified and directed .

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Fixing only old serviceable steel water tubing, galvanized, medium grade, with all new fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

S & F 15mm bore bib tap cast copper alloy fancy type chromium plated long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore stop valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F for 15 mm bore pillar taps, cast copper alloy chromium plated with capstan head screwed down high pressure, with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S & F in repairs Hand Shower (Health Faucet) with 8mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed. (Product Code & Make :- Cat Part No ALD-573 of JAQUAR or equivalent model of KOHLAR/Roca)

S & F in repairs ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as directed of the following sizes:-

20mm bore

25mm bore

S & F in repairs 32mm dia waste coupling of PTMT (half or full threaded) minimum weight 32mm-45 gms complete all as specified and directed.

S & F in repair grating doom 125 mm dia of PTMT (minimum weight 40 gms), complete all as specified and directed.

S & F in repairs PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen sink with plugs, washers and wastes, including bedding cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, over all size 915mm x 460mm bowl size 410 x 330mm x 160mm, complete all as specified and as directed.

S & F in repairs kitchen sink (without drainage board) made of stainless steel 1 mm thick sheet with plug washer and waste coupling including bedding in cement mortar to dwarf wall or including and fixing cantilever brackets and connecting union pipe overall size 495mm x 420mm and bowl size 410 x 330 x 160mm complete all as directed.

S & F 500 litres capacity rotational moulded HDPE water storage tank tripple layer (Cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. Note : PVC tanks shall be ISI marked and having two layers.

S & F 750 litres capacity rotational moulded HDPE water storage tank tripple layer (Cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. Note : PVC tanks shall be ISI marked and having two layers.

M & L for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnectings and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres complete all as specified and directed.

M & L for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnectings and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

S & F in repairs white Vitreous china wash down water closet pan (pedestal pattern) with integral S trap including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) etc complete all as specified and directed. (Product Code & Make :- Cat Part No CNS-WHT-WH-10 of JAQUAR or equivalent model of other makes listed in list of makes).

S & F in repairs PVC (SWR) floor trap 75mm dia outlet plain with Stainless steel grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as directed.

S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S&F in repairs chromium plated towel rail complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-40 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs Overhead Shower 150mm x 150mm square shape single flow ABS body Chrome plated with gray face plate with rubit cleaning system including provision of 450mm long chromium plated best quality shower arm complete all as specified and as directed. (Product Code & Make :- Cat Part No OHS-35495 of JAQUAR or equivalent model of KOHLAR/Roca)

S K ENTERPRISE

M/s Gupta Construction

M/s B.Citymai Syiem