SPECIAL REPAIR TO TYPE III QTR BLOCK NO P21 AT CQA EE RESIDENTIAL COMPLEX AUNDH CAMP PUNE

Amount

Removing old existing water proofing treatment and cleaning the surface of slab with wire brush, removing dust,foreign materials and removing the rubbish off the premises all as directed by Engr-in-Charge.

M & L for PCC M-15 grade (nominal mix) using 12.5 mm graded stone aggregate) on roof top for maintaining of slope coving, benching etc all as specified and directed by Engr-in-Charge.

M&L for rendering 10 mm thick on concrete surfaces of roof in CM 1:3 mixed with liquid water proofing compound as per manufactures instructions finishing even and smooth to receive water proofing treatment complete without using extra cement all as specified and directed by Engr-in-Charge. Note :- Liquid WPC shall be measured and paid seperately under relevant item of BOQ.

M & L for applying APP (Atactic Poly Propylene) bitumen membrane 3mm thick APP modified weight not less than 3.60 Kg/Sqm reinforced with non woven polyester fibre of weight 160 gms/sqm as center core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene, applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer 0.40Kg/Sqm over roof ( An overlap of 100mm & 150mm shall be provided on sides and ends respectively ) complete all as per manufacturers instructions.

Taking up or down steel tubing 20 mm dia and connection including cleaning for refixing for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Taking up or down steel tubing 15 mm dia and connection including cleaning for refixing and removing to store for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Refixing old steel tubing and connection of 20 mm dia in new or old position walls, ceiling, floor etc with new fittings complete.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Refixing old steel tubing and connection of 15 mm dia in new or old position walls, ceiling, floor etc with new fittings complete.

S&F in repairs, gun metal globe or gate valves 20 mm dia, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr-in-Charge.

Dismantling water tank of any description or capacity 500 ltrs all as specified as directed.

Supply and fix 500 liters capacity triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete.

S & F in repairs ball brass valve 20 mm dia high pressure with polythine float and fly nut for following bore of pipe, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats and frame n.exc 1.5 Sqm incl shutter with out taking off shutters from frame all as specified and directed by Engr-in-Charge.

Taking down chowkats and frame exc 1.5 Sqm and n. exc 4.0 sqm incl shutter with out taking off shutters from frame and removing from site specified and directed by Engr-in-Charge

Taking down shutters of any description exceeding 1.00 Sqm and n.exc 2.00 Sqm each all as specified and directed.

S&F powder coated (minimum thickness of powder coating shall not be less than 50 microns of approved colour) aluminium frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium three track window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings all all as specified and directed by Engr-in-Charge. Note : Glazing shall be measured and paid as supply only under relevant item of BOQ. Fixing rate is deemed to be included under limit rate quoted.

S&F powder coated (Powder coating shall not be less than 50 micron of approved colour) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engr-in-Charge. Note : Glazing shall be measured and paid as supply only under relevant item of BOQ. Fixing rate is deemed to be included under limit rate quoted.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Supply only 5.50 mm thick sheet glass, ordinary quality in square n.exc 0.5 sqm in each pane.

Supply only 5mm thick sheet glass, obscured or frosted square n.exc 0.5 sqm in each pane.

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge.

S&F in repairs 12mm thick Veneered decorative plywood, grade 1 (with BWR resin) with only one face has decorative veneer; fixed with screws to timber frame work all as specified and directed by Engr-in-Charge

S&F in repairs second class hard-wood clean sawn timber framed and fixed in scantlings all as specified and directed by Engr-in-Charge.

S&F of 35mm thickness 2nd class HW rail and style of factory made shutter of Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed by Engr-in-Charge.

S&F of 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M&L Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F in repairs stainless steel wire cloath 0.56 mm nominal dia of wire and average width of aperature 1.18mm including fixing with wooden/steel batten all as spd & directed by Engr-in-Charge

M & L for Aluminium alloy barrel tower bolts and fixed 150mm long all as specified and directed by Engr-in-Charge.

S&F butt hinges medium weight colled rolled mild steel 100 mm and fixed all as specified and directed by Engr-in-Charge.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F of 150 mm size Aluminium handles, cast type, anodised all as specified and directed by Engr-in-Charge.

Taking down cement plaster in any description incl racking out joints hacking for key and scrubbing down with water etc all as specified and directed by Engr-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises all as specified and directed by Engr-in-Charge.

M&L for Rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 finishing surface even & smooth complete all as specified and directed by Engr-in-Charge

M&L for Rendering 10mm thick, on concrete surfaces of ceiling in CM 1:4 finishing the surface even and smooth complete all as specified and directed by Engr-in-Charge

M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of stone masonry surface CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for providing and carry out water proofing treatment to toilets, sunken floors slabs, wet areas etc, after proper surface preparation, carry out cementitious injection grouting at leakage points using cobex 100 plasticised expansive grount admixture, application of polymer modified vatta at slab and wall junction using nitobond SBR latex- screed modifier cum bonding agent and application of two coats of brush bond RFX - two- Part acrylic polymer modified cementtious elastometic water proof and protective coating etc, complete including all tools and tackles as per manufactures specification.

M & L for PCC M-5 grade (nominal mix) uisng 40mm graded stone aggregate as in filling, mass concrete, for sunkun floor.

M&L coloured joint freee Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 15mm thick cement screed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L coloured Non Skid ceramic tiles 300 x 300 x 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including 15mm thick cement screed in CM 1: complete all as specified and directed by Engr-in-Charge.

M&L coloured Glazed ceramic tiles in vertical surface of size 300mm x 450mm x 6 to 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over and including cement plaster 10mm thick as in backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for 18-20mm thick machine cut machine polished Kota stone slab flooring laid and jointed in neat cement slurry mixed with pigment to match the shade including cutting and polishing over and including 15 mm thick screed bed in CM 1:3 complete all as specified and directed by Engr-in-Charge.

All as per item No 48 above, but in riser, step, skriting, dados and pillar over 10 mm thick plastering in cement morter 1:3 all as specified.

M&L Granite slab 20 mm thick machine cut bedded and jointed with grey cement and pointed with white cement and adhesive of pigment to match the shade incl cutting and polishing laid over and including 10mm thick screed bed in CM 1:4 complete all as specified as directed by Engr-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs washers and wastes incl bedding in CM to drawf wall incl fitting cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm.

S&F in repairs steel plate rack of 900mm x 750mm x 200mm all as specified and directed by Engr-in-Charge.

S&F in repair 20 mm dia, chromium plated curtain rod with fixing brackets, stops, rollers etc.complete all as specified and directed by Engr-in-Charge. Note : Bracket shall be measured & paid seperately under relevant item of this BOQ.

S&F in repairs bracket of fancy type curtain rod powder coated 20mm dia including fixing to walls with MS full screws (including fixing of wooden pieces of required size of walls) all as specified and directed by Engr-in-Charge.

S&F in repairs aluminium anodised Tubular towel rail 20mm dia, D type, 60cm long between flanges complete.

S & F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15 mm dia all as specified and directed by Engr-in-Charge.

S & F in repairs bib taps CP Brass with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm dia all as specified and directed by Engr-in-Charge.

S & F in repairs brass CP shower rose 125mm size with swivel joint incl fixing to steel pipe fixed in repairs all as specified and directed by Engr-in-Charge.

M & L for 75mm thick PCC M-7.5 grade (nominal mix) uisng 20mm graded stone aggregate as in Plinth, Path, floor with fair finish surface without using extra cement all as specified and directed by Engr-in-Charge.

S & F in repairs viterious china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but incl necessary brackets CP wastes and other fittings all as specified and directed by Engr-in-Charge.

S & F in repairs pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered Hot or Cold Withlong screwed shanks and fly nuts screwed for iron pipes 15mm dia all as specified and directed by Engr-in-Charge.

S&F in repairs PVC waste outlet pipe for kitchen sink complete all as specified and directed.

S & F in repairs water closet (Squat Pattern) complete incl provn of lime concrete bedding Orissa pattern size 580 x 440mm white integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor.

S & F in repairs PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flushpipe, brackets all as specified and directed by Engr-in-Charge.

M&L for PCC M-15 grade (nominal mix) using 12.50mm graded stone aggregrate as in coping, hold fast block, bed block, filling pressed steel door frame etc all as specified.

M&L painting to wooden surfaces of any description over 10 cm width or girth incl prepration of new or untreated surface and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified.

M&L for preparation of newly plastered surfaces and applying two coats of weather proof acrylic exterior paint (100%) Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment & applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash over a coat of wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

M&L for Complete removal of existing treatment on ceiling & applying three coats of white wash over wall care putty not less than 1mm thick finished even and smooth complete all as specified and directed by Engr-in-Charge.

Demolition of brick work PCC block mansonry or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan, exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Taking down drain pipes (any size or pattern), including all fittings, T, bends,etc., including cleaning or refixing (measured overall as fixed along the centre line over fitting and accessories)

S&F 110mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls.

S&F 110 mm bore PVC (SWR) pipes type 'A' single socketed, in any length but except pipe with rubber ring joints, fixed on walls complete all as specified.

S&F 75mm dia PVC (SWR) pipes type 'A' single socketed in any length with rubber ring joints fixed to walls.

S&F 75 mm bore PVC (SWR) pipes type 'A' single socketed, in any length but except pipe with rubber ring joints, fixed on walls complete all as specified.

S&F 110mm dia PVC (SWR) bends any radius complete.

S&F 75mm dia PVC (SWR) bends any radius

S&F 110mm dia PVC (SWR), junction single, (Single T) equal or unequal complete.

S&F 110mm dia PVC (SWR), equal or unequal Single T except (Single T) complete.

S&F 75mm dia PVC (SWR), junction single, (Single Y) equal or unequal

S&F 75mm dia PVC (SWR), junction single, except (Single Y) equal or unequal

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

M & L for point wiring with 1.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in and including PVC concealed conduit heavy grade ISI marked of suitable size including its accessories such as tee, bend ,elbow, socket and chisselling on wall complete also including 1.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire including "concealed" MS terminal box ISI marked with modular cover plate of suitable size as per site requirement for housing switch, socket, regulators etc complete.

One fan / light / bell point controlled by one way modular switch 5/6 Amp.

All as per Item No 88.here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket/AC/Geysers on independent board on the existing Concealed conduit complete all as specified and directed.

M & L for point wiring with 1.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in existing PVC concealed conduit including 1.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire including "concealed" MS terminal box ISI marked with modular cover & plate of suitable size as per site requirement for housing switch, socket, regulators etc complete.

One fan / light / bell point controlled by one way modular switch 5/6 Amp.

One 3 pin 5 Amps socket on same board controlled with one way switch.

One 3 pin 5 Amps socket on independent board

One light point controlled by two way switch complete all as specified and directed.

Supply and fix modular switch 1 way 6A 1 module complete all as specified and directed. Make: Havells /schneider /Roma

Supply and fix modular switch 2 way 6A 1 module complete all as specified and directed. Make :Make: Havells /schneider /Roma

Supply and fix modular bell push 6A 1 module complete all as specified and directed. Make :Make: Havells /schneider /Roma

Supply and fix modular socket 6A 2/3 pin combined 2 module complete all as specified and directed. Make: Havells /schneider /Roma

Supply and fix modular socket 16A 2/3 pin combined 2 module complete all as specified and directed. Make: Make: Havells /schneider /Roma

Supply and fix modular switch 1way 16A 1 module complete all as specified and directed. Make: Havells /schneider /Roma

Supply and fix electric bell Ding Dong, AC 230 volts complete all as specified and directed. Make : Anchor/ Havells/Roma

Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed.

Supply and fix PVC Batten Holder with 10 Watt LED bulb complete all as specified and directed.

S & F in repair fix high efficent LED building security light 35 watt , 230 V , lumen 2000 -3000, PF> 0.95, THD less 10%, made of pressure dia cast aluminuim housing with high power LEDs, lens and lens embedded PC cover having bottom opening seprate driver compartment with IP 66 Protection with three core flexible copper wire from connecto to ceiling rose all as specified and directed Make : Cat part No- Havells ENDURASUNDOWNSL35WLED 765PASYBOPC or equivalent make of Phillips/ jaguar

S & F in repair wall mounted extruded aluminium housing high quality indoor batten LED tube 22 watt colour temperature 6500 K (4" long) lumen 2000 -3000, PF> 0.95, THD less 10% diffused connecting with three core flexible copper wire from connecto to ceiling rose/angle holder as per existing site requirement as directed by Engr-in-charge. Make : Cat part No- Havells LUMILINEPLUSNEOBS22WLED865SPCSSIND or equivalent make of Phillips/ jaguar

S & F in repair decorative wall mounting brused nickel finish opal glass diffuser suitable for 9 Watt bulb B-22 base with LED bulb 09 watt colour temperature 4000-6500 K connecting with three core flexible copper wire as per existing site requirement as directed by Engr-in-charge. Make :Cat part No- LHFOAJE1TZ1l060 Havells or equivalent make of Phillips/ jaguar

Taking down unserviceable submain wiring and M&L for submain wiring in PVC conduit with two runs of 4 sq mm and one runs of 4 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid conduit heavy grade ISI marked (IS 9537 Part III) including accessories such as bends, supports etc all as specified and directed. Note: Two runs of 4 sq mm and one runs of 4 sqmm cable along with conduit shall be measured as one length.

S & F MCB DB SPN 8 way double door type horizontal with 200A bus bar, concealed in wall, matching with surface of wall and making good the disturbed surfaces complete all as specified and directed.

Taking down old unserviceable Vertical TPN distribution boards MCCB as incomer S & F Vertical TPN distribution boards 100 Amps MCCB as incomer IP 43 Double door DB 04 way, concealed in wall matching with surface of wall & making good the disturbed surface earth terminal with earthing all as specified and directed.

M & L for new MCCB 4 pole of capacity 100 Amps, 16 KA, 415 Volts complete all as specified and directed.

Taking down ceiling fan, dismantling the blade & depositing to MES store.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator/remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor. Make : Havells / Almonard / Orient / Usha

Taking down carefully old unserviceable plastic / metalic exhaust fan of any type by disconnecting all electrical connections for carrying out repair/ servicing and refixing in position after repairs complete all as specified and directed. Note: Spray painting shall be measured and paid separately.

M&L for Spray Painting of Exhaust fan of 300/450 mm sweep with one coat of synthetic enamel paint of same colour including preparation of old surfaces complete including numbering of fans as existing complete all as specified and directed.

Supply and fix exhaust fan made of steel body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m ( For Toilets) Note: (i) Rate inclusive of core cutting for fixing exhaust fan (ii) Quoted rate shall deemed to be including plastering & surface finish to match with the existing surface and making good in and out side to repair damage while core cutting complete. Make :Havells/Crompton/Phillips

S & F MCB SP of capacity 5A - 32A "B' curve all as specified and directed. Make : Havells /L&T/Schneider.

Supply and fix MCB DP 40 A " C " curve all as specified and directed. Make : Havells /L&T/Schneider.

Material and labour for earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete. Note : Rate of item is deemed to be included for excavation in hard rock, by compressor machine to achieve required depth.

Cutting chases, pinning in concrete block or slab, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth.

M&L for rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even surface all as specified and directed by Engr-in-Charge

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and directed by Engineer-in-charge.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth for laying UG cable, pipe line etc and getting out in hard / dense soil complete all as specified and directed.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth for laying UG cable, pipe line etc and getting out in soft / loose soil complete all as specified and directed.

Returning, filling, incl spreading levelling, watering and well ramming in layers not exc 25cm all as specified and directed by Engr-in-Charge.

Removing excavated material to distance not exc 50m and depositing where as directed at a level not exc 1.5m above the starting point.

M&L for riddled earth cushioning to under ground cable in trenches / existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engineer-in-Charge Note : Measurement shall be taken after gentling punning.

Supply and laying reinforced precast concrete cable cover class LV, type 1, flat of size 250mm x 150mm x 40mm size for cable protection.

Supply and laying in trenches GI tubing light grade 50mm bore, ISI marked, for cable protection

M&L for road cutting and making good with M-10 grade (nominal mix) using 40mm graded stone aggregate of 150mm X 100mm in respect of width and thickness complete all as specified and directed by Engr-in-Charge.

Sunrise Traders

M/S JAYCONSTRUCTION CO