NBCC RBG KOL ISI Etender 24 329

Bill of Quantity

Sl No. Description of Items Unit QTY RATE AMOUNT

1.0 20.2 Boring, providing and installation bored cast-in-

situ reinforced cement concrete piles of grade

M-25 of specified diameter and length below

the pile cap, to carry a safe working load not

less than specified, excluding the cost of steel

reinforcement but including the cost of boring

with bentonite solution and temporary casing

of appropriate length for setting out and

removal of same and the length of the pile to

be embedded in the pile cap etc. by percussion

drilling using Direct mud circulation (DMC) or

Bailer and chisel technique by tripod and

mechanical Winch Machine all complete,

including removal of excavated earth with all

its lifts and leads (length of pile for payment

shall be measured up to bottom of pile cap).

2.0 10.1 Structural steel work in single section, fixed

with or without connecting plate, including

cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer all

complete. For Guide Casing.

3.0 5.22 Reinforcement for R.C.C. work including

straightening, cutting bending, placing in - -

position and binding all complete.

3.1 5.22.6 Thermo Mechanically treated bars Kg. - 68.10 -

4.0 20.6 Vertical load testing of piles in accordance with

IS 2911 (Part IV) including installation of

loading platform by Kentledge method and

preparation of pile head or construction of test

cap and dismantling of test cap after test etc.

complete as per specification & the direction of

Engineer in-charge.

4.1 20.6.2 Single pile above 50 tonne and upto 100 tonne

4.1.1 20.6.2.1 Initial test (Test Load 2.5 times the Safe

4.1.2 20.6.2.2 Routine test (Test Load 1.5 times the Safe

B EARTH WORK - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

5.0 2.31 Clearing jungle including uprooting of rank

vegetation grass brush wood trees and saplings

of girth up to 30 cm measured at a height of 1

m above ground level and removal of rubbish 100 Sqm. - 642.00 -

up to a distance of 50 m outside the periphery

of the area cleared.

6.0 2.28 Surface dressing of the ground including

removing vegetation and in equalities not

exceeding 15 cm. Deep and disposal of rubbish, - -

lead upto 50 m and lift up to 1.5 m

6.1 2.28.1 All kinds of soil 100 Sqm. - 1,245.75 -

7.0 2.6 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over

areas (exceeding 30 cm in depth 1.5 m in width

as well as 10 sqm. On plan) including disposal

of excavated earth lead up to 50 m and lift

upto 1.5 mtr disposed earth to be levelled and

neatly dressed.

7.1 2.6.1 All kinds of soil Cum. - 155.60 -

8.0 2.26 Extra for every additional lift of 1.5 m or part

thereof in excavation / banking excavated or - -

stacked materials.

8.1 2.26.1 All kinds of soil Cum. - 46.25 -

9.0 2.25 Filling available excavated earth (excluding

rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20 cm in depth,

consolidating each deposited layer by ramming Cum. - 112.40 -

and watering, lead upto 50 m and lift upto 1.5

10.0 2.27 Supplying and filling in plinth with jamuna sand

under floors including, watering, ramming

consolidating and dressing complete.

11.0 2.34 Supplying chemical emulsion in sealed

containers including delivery as specified

11.1 2.34.1 Chlorpyriphos / Lindane emulsifiable

concentrate of 20%

12.0 2.35 Diluting and injecting chemical emulsion for

POST-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical

12.1 2.35.1 Along external wall where the apron is not

provided using chemical emulsion @ 7.5 litres /

sqm of the vertical surface of the substructure

to a depth of 300 mm including excavation

channel along the wall & rodding etc.

12.1.1 2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1%

13.0 2.35.3 Treatment of soil under existing floors using

chemical emulsion @ one litre per hole, 300

mm apart including drilling 12 mm diameter

holes and plugging with cement mortar 1 :2 (1

cement : 2 Coarse sand) to match the existing

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

13.1 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1%

C CONCRETE WORK - -

14.0 4.1 Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering - All work upto

14.1 4.1.6 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 40 mm nominal size)

15.0 4.11 Providing and laying damp proof course 50 mm

thick with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm

16.0 4.12 Extra for providing and mixing water proofing

material in cement concrete work in doses by Per 50 Kg

weight of cement as per manufacturer’s Cement

17.0 4.13 Applying a coat of residual petroleum bitumen

of grade of VG-10 of approved quality using 1.7

kg per square metre on damp proof course

after cleaning the surface with brushes and Sqm. - 132.00 -

finally with a piece of cloth lightly soaked in

18.0 4.17 Making plinth protection 50 mm thick of

cement concrete 1:3:6 (1 cement : 3 coarse

sand : 6 graded stone aggregate 20 mm

nominal size) over 75 mm thick bed by dry

brick ballast 40 mm nominal size well rammed

and consolidated and grouted with fine sand

including finishing the top smooth.

D REINFORCED CEMENT CONCRETE WORK

19.0 5.33 Providing and laying in position machine

batched and machine mixed design mix M-25

grade cement concrete for reinforced cement

concrete work, using cement content as per

approved design mix, including pumping of

concrete to site of laying but excluding the cost

of centering, shuttering, finishing and

reinforcement, including admixtures in

recommended proportions as per IS: 9103 to

accelerate, retard setting of concrete, improve

workability without impairing strength and

durability as per direction of Engineer-in-

(Note :- Cement content considered in this

item is @ 330 kg/cum. Excess/less cement

used as per design mix is payable/recoverable

19.1 5.33.1 All works upto plinth level Cum. 953.72 6,296.15 6,004,793.93

19.2 5.33.2 All works above plinth level upto floor V level

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

20.0 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above

floor V level for each four floors or part Cum. - 174.20 -

21.0 5.35 Add for using extra cement in the items of

design mix over and above the specified Quin 136.74 742.75 101,561.88

cement content therein.

22.0 5.9 Centering and shuttering including strutting

propping etc. and removal of form work for : - -

22.1 5.9.1 Foundations, footings, bases of columns etc.

for mass concrete.

22.2 5.9.2 Walls (any thickness) including attached

pilasters, butteresses, plinth and string courses sqm - 360.80 -

22.3 5.9.3 Suspended floors, roofs, landings, balconies

and access platform.

22.4 5.9.4 Shelves (Cast in situ). Sqm. - 401.65 -

22.5 5.9.5 Lintels, beams, plinth beams, girders,

bressumers and cantilevers.

22.6 5.9.6 Columns, pillars, piers, abutments, posts and

22.7 5.9.7 Stairs (excluding landings) except spiral

22.8 5.9.14 Extra for shuttering in circular work (20% of

respective centering and shuttering items) Sqm. - 90.67 -

22.9 5.9.16 Edges of slabs and breaks in floors and walls.

22.10 5.9.19 Weather shade, Chajjas, corbels etc., including

22.11 5.11.1 Extra for additional height in centering,

shuttering where ever required with adequate

bracing, propping etc., including cost of de-

shuttering and decentering at all levels, over a

height of 3.5 m, for every additional height of 1

metre or part thereof (Plan area to be

22.11.1 5.11.1 Suspended floors, roofs, landing, beams and

balconies (Plan area to be measured)

23.0 5.22 Reinforcement for R.C.C. work including

straightening, cutting bending, placing in

position and binding all complete up to plinth

23.1 5.22.6 Thermo Mechanically treated bars Kg. 61,953.94 68.10 4,219,063.62

24.0 5.16 Providing, hoisting and fixing up to floor five

level precast reinforced cement concrete in

shelves, including setting in cement mortar 1:3

(1 cement : 3 coarse sand), cost of required

centering, shuttering and finishing with neat

cement punning on exposed surfaces but Cum. - 12,174.70 -

excluding the cost of reinforcement, with 1:2:4

(1 cement : 2 coarse sand : 4 graded stone

aggregate 12.5 mm nominal size).

25.0 5.25 Providing and fixing in position copper plate as

per design for expansion joints.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

26.0 5.26 Providing and filling in position, blown bitumen

in expansion joints. per cm

27.0 5.43 Providing and fixing in position Stainless steel

Grade 304 plate-1.0 mm thick as per design for - -

expansion joints.

28.0 5.45 Providing and fixing of expansion joint system

related with wall joint (internal/ external)

location as per drawings and direction of

Engineer-In- Charge. The joints shall be of

extruded aluminum base members, self

aligning / centering arrangement and support

plates as per ASTM B221- 02. The material shall

be such that it provides an Expansion Joints

System suitable for vertical wall to wall/ wall to

corner application, both new and existing

construction in office Buildings & complexes

with no slipping down tendency amongst the

components of the Joint System. The Joint

System shall utilize light weight aluminum

profiles exhibiting minimal exposed aluminum

surfaces mechanically snap locking the

multicellular to facilitate movement. (Material

shall confirm to ASTM 6063.)

E BRICK WORK - -

29.0 6.1 Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in - -

foundation and plinth in:

29.1 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

30.0 6.4 Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V - -

level in all shapes and sizes in :

30.1 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

31.0 6.5 Extra for brick work / AAC block masonry / Tile

brick masonry in superstructure above floor V

level, for each four floors or part thereof by

mechanical means.

32.0 6.13 Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to

32.1 6.13.2 Cement mortar 1:4 (1 cement : 4 coarse sand)

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

33.0 6.14 Extra for half brick masonry in superstructure,

above floor V level for ev ery four floors or part

thereof by mechanical means by lifting material Sqm. - 25.60 -

using mobile crane

34.0 6.15 Extra for providing and placing in position 2

Nos 6mm dia. M.S. bars at every third course of Sqm. - 69.50 -

half brick masonry.

35.0 6.34 Brick work with non modular fly ash lime bricks

(FALG Bricks) conforming to IS:12894, class

designation 10 average compressive strength - -

in super structure above plinth level up to floor

35.1 6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand)

36.0 5.3 Add for plaster drip course/ groove in plastered

surface or moulding to R.C.C. projections. Mtr. - 30.75 -

F WOOD WORK -

37.0 9.1 Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of -

required dia & length ( hold fast lugs or dash

fastener shall be paid for separately).

37.1 9.1.1 Second class Teak wood Cum. -

37.2 9.1.2 Sal wood (Rate for fixing in position with all

38.0 9.5 Providing and fixing panelled or panelled and

glazed shutters for doors, windows and

clerestory windows, including ISI marked M.S.

pressed butt hinges bright finished of required

size with necessary screws, excluding panelling

which will be paid for separately, all complete

as per direction of Engineer-in-charge.

38.1 9.5.1.1 Second class teak wood 35 mm thick shutters

39.0 9.20 Providing and fixing ISI marked flush door

shutters conforming to IS 2202 (part I)

decorativie type, core of block board

construction with frame of 1st class hard wood

and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers

on both faces of shutters

39.1 9.20.1 35 mm thick including ISI marked stainless

steel butt hinges with necessary screws Sqm. 190.43 2,606.45 496,346.27

39.1 9.20.1 35 mm thick including ISI marked stainless

steel butt hinges with necessary screws (fixing

in position with all accessories)

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

40.0 9.23 Extra for providing lipping with 2nd class teak

wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of Sqm. 161.58 365.85 59,114.04

door shutter to be measured).

40.0 9.23 Extra for providing lipping with 2nd class teak

wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of

door shutter to be measured). (Fixing in

position with all required accessories)

41.0 9.53 Providing 40x5 mm flat iron hold fast 40 cm

long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and

embedding in cement concrete block Each 420.00 117.35 49,287.00

30x10x15cm 1:3:6 mix (1 cement : 3 coarse

sand : 6 graded stone aggregate 20mm

42.0 9.74 Providing and fixing bright finished brass tower

bolts (barrel type) with necessary screws etc. - -

43.0 9.75 Providing and fixing bright finished brass door

latch with necessary screws etc. complete : - -

44.0 9.81 Providing and fixing bright finished brass

handles with screws etc. complete :

45.0 9.82 Providing and fixing bright finished brass

hanging type floor door stopper with necessary Each 198.00 85.70 16,968.60

screws, etc. complete

46.0 9.88 Providing and fixing chromium plated brass 100

mm mortice latch and lock with 6 levers and a

pair of lever handles of approved quality with Each 49.00 790.30 38,724.70

necessary screws etc. complete.

47.0 9.96 Providing and fixing aluminium sliding door

bolts ISI marked anodised (anodic coating not

less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or

shade with nuts and screws etc. complete.

48.0 9.97 Providing and fixing aluminium tower bolts ISI

marked anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade with

necessary screws etc. complete.

49.0 9.100 Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade, with

necessary screws etc. complete :

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

50.0 9.16 Providing and fixing 25 mm thick shutters for

cup board etc. :

Panelled or panelled & glazed shutters : - -

50.1 9.16.1.2 Second class teak wood including ISI marked

nickel plated bright finished M.S. piano hinges Sqm. - 2,799.60 -

with necessary screws

51.0 9.136 Providing and fixing fire resistant door frame of

section 143 x 57 mm having built in rebate

made out of 16 SWG G.I. sheet (zinc coating

not less than 120 gm/sqm) duly filled with

vermuculite based concrete mix, suitable for

mounting 60 minutes fire rated door shutters.

The frame is fitted with intumuscent fire seal

strip of size 10x4 mm (minimum) alround the Mtr. 106.00 1,250.05 132,505.30

frame and fixing with dash fastener of

approved size and make, including applying a

coat of approved brand fire resistant primer

etc. complete as per direction of Engineer-in-

charge (Dash fastener to be paid for

52.0 9.137 Providing and fixing 50 mm thick glazed fire

resistant door shutters of 60 minutes fire rating

conforming to IS:3614 (Part-II), tested and

certified as per laboratory approved by

Engineer-in-charge, with suitable mounting on

door frame, consisting of vertical styles, lock

rail, top rail 100 mm wide, bottom rail 200 mm

wide, made out of 16 SWG G.I.sheet (zinc

coating not less than 120 gm/m2) duly filled FR

insulation material and fixing with necessary

stainless steel ball bearing hinges of approved

make, including applying a coat of approved

fire resistant primer etc. all

complete as per direction of Engineer-in-

charge (panneling to be paid for separately).

53.0 9.138 Providing and fixing glazing in fire resistant

door shutters, fixed panels, ventilators and

partitions etc., with G.I. beading of appropriate

size, made out of 20 SWG G.I.sheet (zinc

coating not less than 120 gm/m2), fire resistant

sealant, including applying a coat of approved

fire resistant primer on G.I. beading etc.,

complete all as per direction of Engineer-in-

53.1 9.138.1 With clear fire resistant glass panes 6mm thick

of approved brand, having minimum 60 Sqm. 1.20 27,658.70 33,190.44

minutes fire resistance

54.0 9.139 Providing and fixing panic bar / latch (Double

point) fitted with a single body, Trim Latch &

Lock on back side of the Panic Latch of reputed

brand and manufacture to be approved by the

Engineer- in- charge, all complete.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

G STEEL WORK - -

55.0 10.25 Steel work welded in built up sections/ framed

work, including cutting, hoisting, fixing in

position and applying a priming coat of - -

approved steel primer using structural steel

etc. as required.

55.1 10.25.2 In gratings, frames, guard bar, ladder, railings,

brackets, gates and similar works

56.0 10.19 Providing and fixing mild steel round holding

down bolts with nuts and washer plates Kg. - 73.95 -

57.0 10.26 Providing and fixing hand rail of approved size

by welding etc. to steel ladder railing, balcony

railing, staircase railing and similar works,

including applying priming coat of approved

58.0 10.3 Providing and fixing in position collapsible steel

shutters with vertical channels 20x10x2 mm

and braced with flat iron diagonals 20x5 mm

size, with top and bottom rail of T-iron 40x40x6

mm, with 40 mm dia steel pulleys, complete Sqm. - 5,291.30 -

with bolts, nuts, locking arrangement,

stoppers, handles, including applying a priming

coat of approved steel primer.

59.0 10.6 Supplying and fixing rolling shutters of

approved make, made of required size M.S.

laths, interlocked together through their entire

length and jointed together at the end by end

locks, mounted on specially designed pipe

shaft with brackets, side guides and

arrangements for inside and outside locking

with push and pull operation complete,

including the cost of providing and fixing

necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of

adequate strength conforming to IS: 4454 -

part 1 and M.S. top cover of required thickness

for rolling shutters.as nuts, bolts, fasteners

59.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top

60.0 10.7 Providing and fixing ball bearing for rolling

61.0 10.8 Extra for providing mechanical device chain

and crank operation for operating rolling - -

61.1 10.8.1 Exceeding 10.00 sqm and upto 16.80 sqm in

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

62.0 10.28 Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing,

polishing and making curvature (wherever

required) and fitting the same with necessary

stainless steel nuts and bolts complete, i/c

fixing the railing with necessary accessories &

stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the Kg. 871.70 619.40 539,931.91

floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-

charge, ( for payment purpose only weight of

stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts,

fasteners etc.).

62.0 10.28 Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing,

polishing and making curvature (wherever

required) and fitting the same with necessary

stainless steel nuts and bolts complete, i/c

fixing the railing with necessary accessories &

stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the

floor or the side of waist slab with suitable Kg. 1,565.32 309.70 484,778.55

arrangement as per approval of Engineer-in-

charge, ( for payment purpose only weight of

stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts,

fasteners etc.).

(Preparation and fixing in position with all

required accessories)

H ALUMINIUM WORK - -

63.0 21.1 partitions with extruded built up standard

tubular sections/ appropriate Z sections and

other sections of approved make conforming

to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at

top, bottom and sides with required EPDM

rubber/ neoprene gasket etc. Aluminium

sections shall be smooth, rust free, straight,

mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap

beading for glazing / paneling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions of

Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :

63.1 21.1.1.2 For fixed portion - -

Powder coated aluminium (minimum thickness

of powder coating 50 micron)

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

64.0 21.1.2.2 For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM - -

rubber / neoprene gasket required (Fittings

shall be paid for separately)

Powder coated aluminium (minimum thickness

of powder coating 50 micron)

65.0 21.3 Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

complete as per the architectural drawings and

the directions of engineer-in-charge.

65.1 21.3.1 With float glass panes of 4.0 mm thickness

65.2 21.3.3 With float glass panes of 8 mm thickness Sqm. 441.62 1,338.40 591,064.21

66.0 21.8 Filling the gap in between aluminium frame &

adjacent RCC / Brick / Stone work by providing

weather silicon sealant over backer rod of

approved quality as per architectural drawings

and direction of Engineer-in-charge.

66.1 21.8.1 Upto 5 mm depth and 5 mm width Mtr. 1,793.60 88.75 159,182.00

67.0 21.4 Providing and fixing double action hydraulic

floor spring of approved brand and

manufacture conforming to IS : 6315, having

brand logo embossed on the body / plate with

double spring mechanism and door weight

upto 125 kg, for doors, including cost of cutting

floors, embedding in floors as required and

making good the same matching to the existing

floor finishing and cover plates with brass pivot

and single piece M.S. sheet outer box with

slide plate etc. complete as per the direction of

Engineer-in-charge.

67.1 21.4.1 With stainless steel cover plate minimum 1.25

68.0 21.11 Providing and fixing stainless steel (SS 304

grade) adjustable friction windows stays of

approved quality with necessary stainless steel

screws etc. to the side hung windows as per

direction of Engineer in- charge complete.

69.0 21.12 Providing and fixing aluminium tubular handle

bar 32 mm outer dia, 3.0 mm thick & 2100 mm

long with SS screws etc .complete as per - -

direction of Engineer-in-Charge.

69.1 21.12.2 Powder coated minimum thickness 50 micron

aluminium tubular handle bar

70.0 21.13 Providing and fixing 100mm brass locks (best

make of approved quality) for aluminium doors

including necessary cutting and making good

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

I PLASTERING & POINTING WORK - -

Cement Plaster (In Coarse Sand) - -

71.0 13.4 12 mm cement plaster of mix : - -

72.0 13.6 20 mm cement plaster of mix : - -

73.0 13.22 Extra for plastering exterior walls of height

more than 10 m from ground level for every

additional height of 3 m or part thereof.

74.0 13.11 18 mm cement plaster in two coats under layer

12 mm thick cement plaster 1:5 (1 cement : 5

coarse sand) finished with a top layer 6 mm Sqm. - 240.55 -

thick cement plaster 1:6 (1 cement : 6 fine

75.0 13.16 6 mm cement plaster of mix. - -

76.0 5.30 Add for plaster drip course/ groove in plastered

surface or moulding to R.C.C. projections. Mtr. - 30.75 -

77.0 13.18 Neat cement punning Sqm. - 41.40 -

78.0 13.80 Providing and applying white cement based

putty of average thickness 1 mm, of approved

brand and manufacturer, over the plastered

wall surface to prepare the surface even and

smooth complete.

79.0 13.45 Finishing walls with textured exterior paint of

required shade :

79.1 13.45.1 New work (Two or more coats applied @ 3.28

ltr/10 sqm) over and including priming coat of

exterior primer applied @ 2.20kg/10 sqm

80.0 13.83 Wall painting with premium acrylic emulsion

paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50

grams/litre of approved brand and

manufacture, including applying additional

coats wherever required to achieve even shade

81.0 13.50 Applying priming coat : - -

81.1 13.50.1 With ready mixed pink or Grey primer of

approved brand and manufacture on wood Sqm. - 32.95 -

work (hard and soft wood)

82.0 13.50.3 With ready mixed red oxide zinc chromate

primer of approved brand and manufacture on

steel galvanised iron/steel works

83.0 13.61 Painting with synthetic enamel paint of

approved brand and manufacture to give an - -

83.1 13.61.1 Two or more coats on new work Sqm. - 74.40 -

84.0 13.44 Finishing walls with water proofing cement

paint of required shade :

84.1 13.44.1 New work (Two or more coats applied @ 3.84

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

85.0 13.85 Applying priming coats with primer of

approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

85.1 13.85.3 With water thinnable cement primer on wall

surface having VOC content less than 50 Sqm. 13,899.00 35.85 498,279.26

86.0 13.58 Providing and applying two coats of fire

retardant paint on cleaned wood / ply surface

@ 3.5 sqm per litre per coat including

preparation of base surface as per

recommendations of manufacturer to make

the surface fire retardant.

87.0 13.68 French spirit polishing : Two or more coats on

new works including a coat of wood filler Sqm. - 193.95 -

J STONE WORK - -

88.0 8.2 Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity

counters, window sills , facias and similar

locations of required size, approved shade,

colour and texture laid over 20 mm thick base

cement mortar 1:4 (1 cement : 4 coarse sand), - -

joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete at

88.1 8.2.2 Granite of any colour and shade - -

88.1.1 8.2.2.2 Area of slab over 0.50 sq.m. (Fixing in position

with all required materials)

89.0 8.3 Providing edge moulding to 18 mm thick

marble stone counters, vanities etc. including

machine polishing to edge to give high gloss

finish etc. complete as per design approved by

Engineer-in-charge.

89.1 8.3.2 Granite work Mtr. - 230.55 -

90.0 8.4 Extra for fixing marble /granite stone, over and

above corresponding basic item, in facia and

drops of width upto 150 mm with epoxy resin Mtr. - 247.40 -

based adhesive, including cleaning etc.

91.0 8.5 Extra for providing opening of required size &

shape for wash basin/kitchen sink in kitchen

platform, vanity counter and similar location in

marble/Granite/stone work, including Each - 386.60 -

necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges

92.0 8.6 Mirror polishing on marble work / Granite work

/ stone work where ever required to give high

gloss finish complete.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

K FLOORING WORK - -

93.0 11.41 Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS : 15622, of

approved make, in all colours and shades, laid

on 20mm thick cement mortar 1:4 (1 cement :

4 coarse sand), including grouting the joints

with white cement and matching pigments

etc., complete.

Size of tile 600 x 600 mm. (Rectification and

repair work with all materials)

Size of tile 600 x 600 mm. -( Laying in position

with all materials)

94.0 11.46 Providing and laying Vitrified tiles in different

sizes (thickness to be specified by

manufacturer), with water absorption less than

0.08 % and conforming to I.S. 15622, of

approved make, in all colours & shade, in

skirting, riser of steps, over 12 mm thick bed of

cement mortar 1:3 (1 cement: 3 coarse sand),

including grouting the joint with white cement

& matching pigments etc. complete.

95.0 11.39 Providing and laying rectified Glazed Ceramic

floor tiles of size 300x300 mm or more

(thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in colours White,

Ivory, Grey, Fume Red Brown, laid on 20 mm Sqm. 100.01 950.05 95,012.04

thick cement mortar 1:4 (1 Cement: 4 Coarse

sand), including grouting the joints with white

cement and matching pigments etc., complete.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

96.0 11.52 Providing and laying machine cut, mirror

polished Marble stone flooring, in required

design (Simple geometrical, abstract etc.) and

in patterns in combination with Italian marble

stones of different colours, shades and finished

surface texture etc., in linear portions of the

building, all complete as per the architectural

drawings, with 18 mm thick stone slab laid over

20 mm (average) thick base of cement mortar

1:4 (1 cement : 4 coarse sand) laid and jointed

with white cement slurry @ 4.4 kg/sqm

including pointing with white cement slurry

admixed with pigment to match the marble

shade including rubbing, curing and polishing

etc. all complete as specified and as directed

by the Engineer-in-Charge. a. 18 mm thick

Italian Marble stone slab,Perlato, Rosso verona,

Fire Red or Dark Emperadore

97.0 11.23 Marble stone flooring with 18 mm thick marble

stone, as per sample of marble approved by

Engineer-in-charge, over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with grey cement slurry,

including rubbing and polishing complete with :

97.1 11.23.1 Makrana white second quality Sqm. - 3,360.45 -

97.2 11.23.1 Udaipur green marble Sqm. - 1,757.60 -

98.0 11.24 Extra for pre finished nosing to treads of steps

of marble stone.

99.0 11.25 Extra for marble stone flooring in treads of

steps and risers using single length up to 2.00 Sqm. - 320.30 -

100.0 11.26 Kota stone slab flooring over 20 mm (average)

thick base laid over and jointed with grey

cement slurry mixed with pigment to match

the shade of the slab, including rubbing and - -

polishing complete with base of cement mortar

1 : 4 (1 cement : 4 coarse sand) :

101.0 11.27 Kota stone slabs 20 mm thick in risers of steps,

skirting, dado and pillars laid on 12 mm

(average) thick cement mortar 1:3 (1 cement: 3

coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade

of the slabs, including rubbing and polishing

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

102.0 11.39 Providing and laying rectified Glazed Ceramic

floor tiles of size 300 x 300 mm or more

(thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in colours White,

Ivory, Grey, Fume Red Brown, laid on 20 mm Sqm. - 950.05 -

thick cement mortar 1:4 (1 Cement: 4 Coarse

sand), including grouting the joints with white

cement and matching pigments etc., complete.

103.0 11.40 Providing and laying rectified Glazed Ceramic

floor tiles of size 300 x 300 mm or more

(thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in all colours,

shades, except White, Ivory, Grey, Fume Red Sqm. - 1,009.60 -

Brown, laid on 20 mm thick Cement Mortar 1:4

(1 Cement : 4 Coarse sand), including pointing

the joints with white cement and matching

pigments etc., complete.

104.0 11.36 Providing and fixing Ist quality ceramic glazed

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement Sqm. - 836.65 -

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

105.0 16.68 Providing and laying 60mm thick factory made

cement concrete interlocking paver block of M -

30 grade made by block making machine with

strong vibratory compaction, of approved size,

design & shape, laid in required colour and

pattern over and including 50mm thick

compacted bed of coarse sand, filling the joints

with fine sand etc. all complete as per the

direction of Engineer-in-charge.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

106.0 16.69 Providing and laying at or near ground level

factory made kerb stone of M- 25 grade

cement concrete in position to the required

line, level and curvature, jointed with cement

mortar 1:3 (1 cement: 3 coarse sand), including

making joints with or without grooves

(thickness of joints except at sharp curve shall

not to more than 5mm), including making Cum. 29.82 5,295.90 157,936.85

drainage opening wherever required complete

etc. as per direction of Engineer-in-charge

(length of finished kerb edging shall be

measured for payment). (Precast C.C. kerb

stone shall be approved by Engineer-in-

L FALSE CEILING WORK - -

107.0 12.53 Providing and Fixing 15 mm thick densified

tegular edged eco friendly light weight calcium

silicate false ceiling tiles of approved texture

spintone/ cosmos / Hexa or equivalent of size

595 x 595 mm in true horizontal level,

suspended on inter locking metal grid of hot

dipped galvanised steel sections (galvanising @

120 grams per sqm including both side)

consisting of main ‘T’ runner suitably spaced at

joints to get required length and of size 24x38

mm made from 0.33 mm thick (minimum)

sheet, spaced 1200 mm centre to centre, and

cross “T” of size 24x28 mm made out of 0.33

mm (Minimum) sheet, 1200 mm long spaced - -

between main’T’ at 600 mm centre to centre to

form a grid of 1200x600 mm and secondary

cross ‘T’ of length 600 mm and size 24 x28 mm

made of 0.33 mm thick (Minimum) sheet to be

inter locked at middle of the 1200x 600 mm

panel to from grid of size 600x600 mm, resting

on periphery walls /partitions on a Perimeter

wall angle pre-coated steel of size(24x24X3000

mm made of 0.40 mm thick (minimum) sheet

with the help of rawl plugs at 450 mm centre

to centre with 25 mm long dry wall screws @

230 mm interval and laying 15 mm thick

densified edges calicum silicate ceiling tiles of

approved texturecleats

using G.I. slotted (Spintone / Cosmos/hexa)

of size 25x35x1.6 mmin

fixed to ceiling with 12.5 mm dia and 50 mm

long dash fasteners, 4 mm G.I. adjustable rods

with galvanised steel level clips of size 85 x 30 x

0.8 mm, spaced at 1200 mm centre to centre

along main ‘T’, bottom exposed with 24 mm of Sqm. 1,528.58 1,649.15 2,520,858.72

all Tsections shall be pre-painted with polyster

baked paint, for all heights, as per

specifications, drawings and as directed by

engineer-in-charge.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

107.1 Note :- Only calcium silicate false ceiling area

will be measured from wall to wall. No

deduction shall be made for exposed

frames/opening (cut outs) having area less

than 0.30 sqm.The calcium silicate ceiling tile

shall have NRC value of 0.50 (Minimum), light

reflection > 85%, noncombustible as per B.S.

476 part IV, 100% humidity resistance and also

having thermal conductivity <0.043 w/m 0 KC.

M WATER PROOFING TREATEMENT WORK - -

108.0 12.41 Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

109.0 12.42 Providing and fixing on wall face unplasticised-

PVC moulded fittings / accessories for

unplasticised rigid PVC rain water pipes

conforming to IS : 13592 type A including - -

jointing with seal ring conforming to IS : 5382

leaving 10 mm gap for thermal expansion.

109.2 12.42.4 Single tee without door - -

110.0 12.43 Providing and fixing unplasticised PVC pipe

clips of approved design to unplasticised PVC

rain water pipes by means of 50 x 50 x 50 mm

hard wood plugs screwed with MS screws of

required length including cuting brick work and - -

fixing in cement mortar 1:4 (1 cement : 4

coarse sand) and making good the wall etc.

111.0 12.44 Providing and fixing to the inlet mouth of rain

water pipes cast iron grating 15 cm diametre

and weighing not less than 440 grams.

112.0 12.21 Providing gola 75x75 mm in cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 stone

aggregate 10 mm and down gauge), including

finishing with cement mortar 1:3 (1 cement : 3

fine sand) as per standard design :

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

113.0 12.22 Making khurras 45 x 45 cm with average

minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate of 20 mm nominal size) over

PVC sheet 1m x 1m x 400 micron, finished with

12 mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement rounding the

edge and making and finishing the outlet

114.0 22.5 Providing and laying water proofing treatment

in sunken portion of WCs, bathroom etc., by

applying cement slurry mixed with water

proofing cement compound consisting of

applying : a) First layer of slurry of cement @

0.488 kg/sqm mixed with water proofing

cement compound @ 0.253 kg/ sqm. This layer

will be allowed to air cure for 4 hours. b)

Second layer of slurry of cement @ 0.242

kg/sqm mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will be

allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing

of all joints, corners, junctions of pipes and

masonry with polymer mixed slurry.

115.0 22.20 Providing and laying APP (Atactic

Polypropylene Polymer) modified prefabricated

five layer 3 mm thick water proofing

membrane, black finished reinforced with non-

woven polyester matt consisting of a coat of

bitumen primer for bitumen membrane @ 0.40

litre/sqm by the same membrane manufacture

of density at 25°C, 0.87-0.89 kg/ litre and

viscocity 70-160 cps. Over the primer coat the

layer of membrane shall be laid using Butane

Torch and sealing all joints etc, and preparing

the surface complete. The vital physical and

chemical parameters of the membrane shall be

as under : Joint strength in longitudinal and Sqm. 839.83 425.35 357,223.67

transverse direction at 23°C as 650/ 450N/5cm.

Tear strength in longitudinal and transverse

direction as 300/250N. Softening point of

membrane not less than 150°C. Cold flexibility

shall be upto -2°C when tested in accordance

with ASTM, D - 5147. The laying of membrane

shall be got done through the authorised

applicator of the manufacturer of membrane :

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

116.0 22.21 Extra for covering top of membrane with

Geotextile, 120 gsm non woven, 100%

polyester of thickness 1 to 1.25 mm bonded to

the membrane with intermittent touch by Sqm. 839.83 74.85 62,861.62

heating the membrane by Butane Torch as per

manufactures recommendation.

117.0 12.63 Providing and applying two coats of High

Albedo paint having minimum Solar Reflective

Index (SRI) 108 (with solar reflectance &

thermal emittance tested as per ASTM) C 1549

and ASTM C 1371 respectively), VOC less than

10 cc/gm. The coating thickness and the

methodology of application shall strctly as per

manufacturer’s specifications and as approved

by engineer In charge. Surface preparation

includes cleaning with metal wire brush to

remove all dust, fungus etc., washing with

water all complete. The contractor shall give

guarantee for the perfomance of SRI and also

the durabitity of coating, all complete as per

direction of Engineer-in-incharge.

118.0 22.14 Grading roof for water proofing treatment with

118.1 22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4graded stone aggregate 20 mm Cum. 46.56 5,570.55 259,337.20

A TOTAL FOR CIVIL WORK 27,900,732.15

17.0 SANITARY INSTALLATIONS :

1.0 17.78 Providing and fixing white vitreous china

extended wall mounting water closet of size

780x370x690 mm of approved shape including

providing & fixing white vitreous china cistern

with dual flush fitting, of flushing capacity 3 Each 121.00 10,100.90 1,222,208.90

litre/6 litre (adjustable to 4 litre/8 litres),

including seat cover, and cistern fittings, nuts,

bolts and gasket etc complete.

2.0 17.7 Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32 mm

C.P. brass waste of standard pattern, including

painting of fittings and brackets, cutting and

making good the walls wherever require :

2.1 17.7.4 White Vitreous China Flat back wash basin size

550 x 400 mm with single 15 mm C.P. brass Each 129.00 1,807.10 233,115.90

3.0 17.10 Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS 13983 with C.I.

brackets and stainless steel plug 40 mm

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.1 Kitchen sink with drain board - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

4.0 17.28 Providing and fixing P.V.C. waste pipe for sink

or wash basin including P.V.C. waste fittings - -

17.28.2 Flexible pipe - -

5.0 17.29 Providing and fixing 100 mm sand cast Iron

grating for gully trap.

6.0 17.35 Providing and fixing soil, waste and vent pipes :

6.1 17.35.1.2 Centrifugally cast (spun) iron socket & spigot

(S&S) pipe as per IS: 3989

7.0 17.37 Providing and fixing M.S. holder-bat clamps of

approved design to Sand Cast iron/cast iron

(spun) pipe embedded in and including cement

concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone - -

aggregate 20 mm nominal size) including cost

of cutting holes and making good the walls etc.

8.0 17.38 Providing and fixing bend of required degree

with access door, insertion rubber washer 3

mm thick, bolts and nuts complete.

8.1 17.38.1.2 Sand cast iron S&S pipe as per IS: 3989. Each - 385.70 -

9.0 17.39 Providing and fixing plain bend of required

9.1 17.39.1.2 Sand cast iron S&S pipe as per IS: 3989. Each - 335.75 -

10.0 17.43 Providing and fixing single equal plain junction

of required degree with access door, insertion

rubber washer 3 mm thick, bolts and nuts

10.1 17.43.1.2 Sand cast iron S&S as per IS - 3989 Each - 623.80 -

11.0 17.50 Providing and fixing single equal plain invert

branch of required degree:

11.1 17.50.1.2 Sand cast iron S&S pipe as per IS: 3989. Each - 521.60 -

12.0 17.54 Providing and fixing sand cast iron S&S off sets

as per IS: 3989

17.54.2 150 mm off sets - -

13.0 17.58 Providing lead caulked joints to sand cast

iron/centrifugally cast (spun) iron pipes and - -

fittings of diameter:

14.0 17.59 Providing and fixing M.S. stays and clamps for

sand cast iron/centrifugally cast (spun) iron - -

pipes of diameter :

15.0 17.60 Providing and fixing trap of self cleansing

design with screwed down or hinged grating

with or without vent arm complete, including - -

cost of cutting and making good the walls and

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

17.60.1 100 mm inlet and 100 mm outlet - -

15.1 17.60.1.2 Sand cast iron S&S pipe as per IS: 1729. Each - 796.70 -

16.0 17.65 Painting sand cast iron/ centrifugally cast

(spun) iron soil, waste vent pipes and fittings

with two coats of synthetic enamel paint of any

colour such as chocolate grey, or buff etc. over - -

a coat of primer (of approved quality) for new

16.1 17.65.1 100 mm diameter pipe Mtr. - 38.65 -

17.0 17.70 Providing and fixing PTMT Bottle Trap for Wash

basin and sink.

17.1 17.70.2 Bottle trap 38 mm single piece moulded with

height of 270 mm, effective length of tail pipe

260 mm from the centre of the waste coupling

77 mm breadth with 25 mm minimum water

seal, weighing not less than 263 gms.

18.0 17.31 Providing and fixing 600x450 mm beveled edge

mirror of superior glass (of approved quality)

complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws

and washers complete.

19.0 17.72 Providing and fixing PTMT towel ring

trapezoidal shape 215 mm long, 200 mm wide

with minimum distances of 37 mm from wall

face with concealed fittings arrangement of

approved quality and colour, weighing not less

20.0 17.73 Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings - -

arrangement of approved quality and colour.

20.1 17.73.2 600 mm long towel rail with total length of 645

mm, width 78 mm and effective height of 88

mm, weighing not less than 190 gms

18.0 WATER SUPPLY : - -

21.0 18.8 Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings, i/c fixing the

pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one - -

step CPVC solvent cement and the cost of

cutting chases and making good the same

including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and

making good the walls etc.

21.1 18.8.1 15 mm nominal outer dia Pipes Mtr. - 270.00 -

21.2 18.8.2 20 mm nominal outer dia Pipes Mtr. - 296.40 -

21.3 18.8.3 25 mm nominal outer dia Pipes Mtr. - 351.30 -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

22.0 18.10 Providing and fixing G.I. pipes complete with

G.I. fittings and clamps, including cutting and - -

making good the walls etc.

Internal work – Exposed on wall. - -

22.1 18.10.3 25 mm dia. nominal bore Mtr. - 304.15 -

22.2 18.10.4 32 mm dia. nominal bore Mtr. - 343.20 -

22.3 18.10.5 40 mm dia. nominal bore Mtr. - 425.65 -

22.4 18.10.6 50 mm dia. nominal bore Mtr. - 527.20 -

23.0 18.12 Providing and fixing G.I. pipes complete with

G.I. fittings including trenching and refilling etc. - -

External work - -

23.1 18.12.5 40 mm dia. nominal bore Mtr. - 334.15 -

24.0 18.13 Making connection of G.I. distribution branch

with G.I. main of following sizes by providing

and fixing tee, including cutting and threading - -

the pipe etc. complete :

24.1 18.13.1 25 to 40 mm nominal bore Each - 367.75 -

24.2 18.13.2 50 to 80 mm nominal bore Each - 761.10 -

25.0 18.17 Providing and fixing gun metal gate valve with

C.I. wheel of approved quality (screwed end) : - -

25.1 18.17.3 40 mm nominal bore Each - 585.50 -

25.2 18.17.4 50 mm nominal bore Each - 750.75 -

26.0 18.18 Providing and fixing ball valve (brass) of

approved quality, High or low pressure, with - -

plastic floats complete :

26.1 18.18.2 20 mm nominal bore Each - 409.90 -

26.2 18.18.3 25 mm nominal bore Each - 449.95 -

27.0 18.19 Providing and fixing gun metal non- return

valve of approved quality (screwed end) : - -

18.19.3 40 mm nominal bore - -

27.1 18.19.3.1 Horizontal Each - 683.75 -

28.0 18.38 Painting G.I. pipes and fittings with synthetic

enamel white paint with two coats over a

ready mixed priming coat, both of approved

quality for new work :

28.1 18.38.3 25 mm diameter pipe. Mtr. - 14.95 -

28.2 18.38.4 32 mm diameter pipe. Mtr. - 17.70 -

28.3 18.38.5 40 mm diameter pipe. Mtr. - 21.00 -

28.4 18.38.6 50 mm diameter pipe. Mtr. - 24.75 -

29.0 18.51 Providing and fixing C.P. brass long body bib

cock of approved quality conforming to IS

standards and weighing not less than 690 gms.

29.1 18.51.1 15 mm nominal bore. Each - 610.65 -

30.0 18.52 Providing and fixing C.P. brass stop cock

(concealed) of standard design and of - -

approved make conforming to IS:8931.

30.1 18.52.1 15 mm nominal bore. Each - 619.75 -

31.0 18.53 Providing and fixing C.P. brass angle valve for

basin mixer and geyser points of approved

quality conforming to IS:8931

31.1 18.53.1 15 mm nominal bore Each - 507.70 -

32.0 18.21 Providing and fixing uplasticised PVC

connection pipe with brass unions :

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

18.21.2 45 cm length - -

18.21.2.1 15 mm nominal bore Each - 68.60 -

19.0 DRAINAGE - -

NOTE : - The rates given for all the items under

sub-head ‘ Drainage’ are applicable to work

executed in soils above sub- soil water level.

Extra allowance has to be made for work under

sub- soil water level.

33.0 19.1 Providing, laying and jointing glazed stoneware

pipes class SP 1 with stiff mixture of cement

mortar in the proportion of 1:1 (1 cement : 1 - -

fine sand) including testing of joints etc.

34.0 19.3 Providing and laying cement concrete 1:5:10 (1

cement : 5 coarse sand : 10 graded stone

aggregate 40 mm nominal size) up to haunches

of S.W. pipes including bed concrete as per

standard design :

34.1 19.3.2 150 mm diameter S.W. pipe Mtr. - 456.45 -

34.2 19.3.3 200 mm diameter S.W. pipe Mtr. - 536.55 -

35.0 19.21 Making connection of drain or sewer line with

existing manhole including breaking into and

making good the walls, floors with cement

concrete 1:2:4 mix (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size)

cement plastered on both sides with cement - -

mortar 1:3 (1 cement : 3 coarse sand) finished

with a floating coat of neat cement and making

necessary channels for the drain etc. complete

35.1 19.21.1 For pipes 100 to 250 mm diameter Each - 364.60 -

36.0 19.27 Constructing brick masonry road gully chamber

50x45x60 cm with bricks in cement mortar 1:4

(1 cement : 4 coarse sand) including 500x450

mm pre-cast R.C.C. horizontal grating with

frame complete as per standard design :

36.1 19.27.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

37.0 19.30 Constructing brick masonry chamber for

underground C.I. inspection chamber and

bends with bricks in cement mortar 1:4 (1

cement : 4 coarse sand) C.I. cover with frame

(light duty) 455x610 mm internal dimensions,

total weight of cover with frame to be not less

than 38 kg (weight of cover 23 kg and weight of

frame 15 kg), R.C.C. top slab with 1:2:4 mix (1

cement: 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), foundation - -

concrete 1:5:10 (1 cement : 5 fine sand : 10

graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand), finished

smooth with a floating coat of neat cement on

walls and bed concrete etc. complete as per

standard design:

19.30.1 Inside dimensions 455 x 610 mm and 45 cm

deep for single pipe line :

37.1 19.30.1.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

38.0 19.31 Extra for depth beyond 45 cm of brick masonry

38.1 19.31.1.1 With common burnt clay F.P.S. (non modular)

bricks of class designation 7.5

TOTAL FOR SANITARY &

ELECTRICAL WORKS

A. CIRCUIT AND POINT WIRING (SUPPLY,

INSTALLATION, TESTING AND

1 Chapter Wiring for light point/ fan point/ exhaust fan

1/ page point/ call bell point with 1.5 sq.mm FRLS PVC

1/ item insulated copper conductor single core cable in

1.10 surface / recessed medium class PVC conduit,

with modular switch, modular plate, suitable GI

box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single

core cable etc as required.

1.1 Item Group A

1.2 Item Group B

2 Chapter Wiring for light/ power plug with 2X4 sq. mm

1/ page FRLS PVC insulated copper conductor single

1/ item core cable in surface/ recessed medium class

1.12 PVC conduit alongwith 1 No 4 sq. mm FRLS PVC Meter - 162.00 -

insulated copper conductor single core cable

for loop earthing as required.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

3 Chapter Wiring for circuit/ submain wiring alongwith

1/ page earth wire with the following sizes of FRLS PVC

2/ item insulated copper conductor, single core cable

1.14 in surface/ recessed medium class PVC conduit

3.1 Item 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

3.2 Item 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

3.3 Item 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

3.4 Item 4 X 10 sq. mm + 2 X 10 sq. mm earth wire

4 Chapter Supplying and fixing of following sizes of steel

1/ page conduit along with accessories in

5/ item surface/recess including painting in case of

1.20 surface conduit, or cutting the wall and making

good the same in case of recessed conduit as

4.1 Item 20 mm

4.2 Item 25 mm

5 Chapter Supplying and fixing of following sizes of

1/ page medium class PVC conduit along with

5/ item accessories in surface/recess including cutting

1.21 the wall and making good the same in case of

recessed conduit as required.

5.1 Item 20 mm

5.2 Item 25 mm

6 Chapter Supplying and drawing following sizes of FRLS

1/ page PVC insulated copper conductor, single core

3&4/ cable in the existing surface/ recessed steel / - -

item 1.17 PVC conduit as required.

6.1 Item 3 x 1.5 sq. mm

6.2 Item 3 x 2.5 sq. mm

7 Chapter Supplying and fixing following size/ modules, GI

1/ page box alongwith modular base & cover plate for

6/ item modular switches in recess etc. as required.

7.1 Item 1 or 2 Module (75mmX75mm)

7.2 Item 3 Module (100mmX75mm)

7.3 Item 4 Module (125mmX75mm)

7.4 Item 6 Module (200mmX75mm)

7.5 Item 8 Module (125mmX125mm)

7.6 Item 12 Module (200mmX150mm)

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

8 Chapter Supplying and fixing suitable size GI box with

1/ page modular plate and cover in front on surface or

7/ item in recess, including providing and fixing 3 pin

1.31 5/6 amps modular socket outlet and 5/6 amps

modular switch, connection etc. as required.

(For light plugs to be used in non residential

9 Chapter Supplying and fixing following modular switch/

1/ page socket on the existing modular plate & switch

6/ item box including connections but excluding - -

1.24 modular plate etc. as required.

9.1 Item 5/6 amps switch

9.2 Item 15/16 amp switch

9.3 Item 3 pin 5/6 amp socket outlet

9.4 Item 6 pin 15/16 amp socket outlet

9.5 Item Telephone socket outlet

9.6 Item TV antenna socket outlet

9.7 Item Bell Push

10 Chapter Supplying and drawing of UTP 4 pair CAT 6 LAN

1/ page Cable in the existing surface/ recessed steel/

8/ item PVC conduit as required.

11 Chapter Supplying and fixing modular blanking plate on

1/ page the existing modular plate & switch box

6/ item excluding modular plate as required.

12 Chapter Supplying and drawing following pair 0.5 mm

1/ page dia FRLS PVC insulated annealed copper

4/ item conductor, unarmored telephone cable in the - -

1.18 existing surface/ recessed steel/ PVC conduit as

12.1 Item 1 Pair

12.2 Item 4 Pair

B. CABLES, MAINS AND SUB MAINS - -

1 Chapter Laying of one number PVC insulated and PVC

7/ page sheathed / XLPE power cable of 1.1 KV grade of

25/ item following size direct in ground including

7.1 excavation, sand cushioning, protective

covering and refilling the trench etc as

1.1 Item Upto 35 sq. mm

1.2 Item Above 35 sq. mm and upto 95 sq. mm

1.3 Item Above 185 sq. mm and upto 400 sq. mm

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

2 Chapter Laying and fixing of one number PVC insulated

7/ page and PVC sheathed / XLPE power cable of 1.1 KV

26/ item grade of following size on wall surface as

2.1 Item Upto 35 sq. mm (clamped with 1mm thick

2.2 Item Above 35 sq. mm and upto 95 sq. mm

7.7.2 (clamped with 25x3mm MS flat clamp)

3 Chapter Laying and fixing of one number PVC insulated

7/ page and PVC sheathed / XLPE power cable of 1.1 KV

26/ item grade of following size on cable tray as

3.1 Item Upto 35 sq. mm (clamped with 1mm thick

3.2 Item Above 35 sq. mm and upto 95 sq. mm

7.8.2 (clamped with 25x3 mm MS flat clamp)

4 Chapter Supplying and making end termination with

9/ page brass compression gland and aluminium lugs

29/ item for following size of PVC insulated and PVC

9.1 sheathed / XLPE aluminium conductor cable of

1.1 KV grade as required.

4.1 Item 3X 10 sq.mm (22mm)

4.2 Item 4 X 10 sq. mm (25mm)

4.3 Item 4 X 16 sq. mm (28mm)

4.4 Item 4 X 25 sq. mm (28mm)

4.5 Item 3½ X 35 sq. mm (32mm)

4.6 Item 3½ X 70 sq. mm (38mm)

4.7 Item 3½ X 95 sq. mm (48mm)

4.8 Item 3½ X 300 sq. mm (70mm)

5 Chapter Supplying and fixing cable route marker with

7/ page 10 cm X 10 cm X 5 mm thick G.I. plate with

26/ item inscription there on, bolted /welded to 35 mm

7.10 X 35 mm X 6 mm angle iron, 60 cm long and

fixing the same in ground as required.

C. CABLE TRAYS, RACEWAYS AND JUNCTION

1 Chapter Supplying and installing following size of

4/ page perforated pre-painted M.S. cable trays with

19/ item perforation not more than 17.5%, in

4.1 convenient sections, joined with connectors,

suspended from the ceiling with M.S.

suspenders including bolts & nuts, painting

suspenders etc as required.

1.1 Item 300 mm width X 50 mm depth X 1.6 mm

4.1.4 thickness

1.2 Item 150 mm width X 50 mm depth X 1.6 mm

4.1.2 thickness

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

1.3 Item 100 mm width X 50 mm depth X 1.6 mm

4.1.1 thickness

D. EARTHING INSTALLATION - -

1 Chapter Earthing with copper earth plate 600 mm X 600

5/ page mm X 3 mm thick including accessories, and

22/ item providing masonry enclosure with cover plate

5.6 having locking arrangement and watering pipe Set 2.00 9,292.00 18,584.00

of 2.7 metre long etc. with charcoal/ coke and

salt as required.

2 Chapter Earthing with G.I. earth plate 600 mm X 600

5/ page mm X 6 mm thick including accessories, and

22/ item providing masonry enclosure with cover plate

5.4 having locking arrangement and watering pipe Set 14.00 4,490.00 62,860.00

of 2.7 metre long etc. with charcoal/ coke and

salt as required.

3 Chapter Providing and fixing 25 mm X 5 mm copper

5/ page strip in 40 mm dia G.I. pipe FRLS om earth

22/ item electrode including connection with brass nut, Metre - 1,082.00 -

5.10 bolt, spring, washer excavation and re-filling

etc. as required.

4 Chapter Providing and fixing 25 mm X 5 mm G.I. strip in

5/ page 40 mm dia G.I. pipe FRLS om earth electrode

23/ item including connection with G.I. nut, bolt, spring, Metre -0.91 421.00 -383.95

5.11 washer excavation and re-filling etc. as

5 Chapter Providing and fixing 6 SWG dia G.I. wire on

5/ page surface or in recess for loop earthing along

23/ item with existing surface/ recessed conduit/ Metre 192.00 23.00 4,416.00

5.18 submain wiring/ cable as required.

6 Chapter Providing, laying and fixing following dia G.I.

14/ page pipe (medium class) in ground complete with

44/ item G.I. fittings including trenching (75 cm

14.13 deep)and re-filling etc as required

6.1 Item 50 mm dia pipe.

E. LIGHTNING PROTECTION SYSTEM - -

1 Chapter Providing and fixing of lightning conductor

6/ page finial, made of 25 mm dia 300 mm long, G.I.

24/ item tube, having single prong at top, with 85 mm

6.2 dia 6 mm thick G.I. base plate including holes

etc. complete as required.

2 Chapter Fixing of lightning conductor finial (single

6/ page prong) with base plate including holes etc.

24/ item complete as required.

4 Chapter Jointing copper / G.I. tape (with another

6/ page copper/ G I tape, base of the finial or any other

24/ item metallic object) by riveting / nut bolting/ Each 50.00 72.00 3,600.00

6.4 sweating and soldering etc as required.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

5 Chapter Providing and fixing G.I. tape 20 mm X 3 mm

6/ page thick on parapet or surface of wall for lightning

24/ item conductor complete as required. (For

6.7 horizontal run)

6 Chapter Providing and fixing G.I. tape 20 mm X 3 mm

6/ page thick on parapet or surface of wall for lightning

24/ item conductor complete as required. (For vertical

7 Chapter Providing and fixing testing joint, made of 20

6/ page mm X 3 mm thick G.I. strip, 125 mm long, with

24/ item 4 nos. of G.I. bolts, nuts, chuck nuts and spring Each 12.00 71.00 852.00

6.12 washers etc. complete as required.

8 Chapter Providing and laying G.I. tape 32 mm X 6 mm

6/ page from earth electrode directly in ground as

24/ item required. Metre - 141.00 -

TOTAL FOR ELECTRICAL

A) FIRE HYDRANT , WET RISER , SPRINKLER

1.0 2.6.1 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over

areas (exceeding 30 cm in depth 1.5 m in width

as well as 10 sqm. On plan) including disposal

of excavated earth lead up to 50 m and lift

upto 1.5 mtr disposed earth to be levelled and

neatly dressed in all kinds of soil.

2.0 2.25 Filling available excavated earth (excluding

rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20 cm in depth,

consolidating each deposited layer by ramming Cum - 112.40 -

and watering, lead upto 50 m and lift upto 1.5

TOTAL AMOUNT (A+B+C+D) 33,330,127.07

TOTAL AMOUNT (A+B+C+D) 33,330,127.07

Add as cost enhancement 3,333,012.71

TOTAL FOR SCHEDULE ITEMS (X) 36,663,139.77

NON SCHEDULE ITEM

Sl No. NS Description of Items Unit

NON SCHEDULE - CIVIL

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

1.0 G 121 I Supplying, fitting, fixing decorative lamination

conforming to IS : 2046 -1995 as per approved

make, brand, finish and thickness with fitting,

fixing the same on Particle / MDF / Ply Boards

with recommended / approved adhesive with

proper clipping the sides for better attachment

as per direction of Engineer-in-Charge. The rate

includes the cost of labour, adhesive and all

incidental charges thereof.

1.1 Glossy / Matt / Suede excluding surface texture

or metallic lustre. Thickness of laminate 1.5 Sqm. 588.08 961.00 565,144.88

2.0 Providing and fixing 40 mm dia 50 mm long

rubber buffer with necessary screws complete. Each - 80.00 -

3.0 Labour for fixing glass to stainless steel railing.

4.0 Supplying and laying paver tiles of any shade

and of approved quality with (1:1.5:3) cement

concrete laid in panels or patterns as directed

in pavement, footpath etc. including necessary

underlay 25 mm. thick (avg.) cement morter

(1:3) cpmplete in all respect with all labour and

materials. [Using cement slurry @ 4.4 kg. /

Sqm. at back side and @ 2.4 kg. / Sqm. for joint

5.0 Providing & Fixing Luxalon ® 84R Plain Panel

Aluminum Sun Louver System as manufactured

by Hunter Douglas India Pvt.Ltd. of approved

colour (as per Luxalon ® Colour Chart). The

system shall consist of panel 84mm Wide x

16mm deep x 0.6mm Thick in standard length

of up to 6m. The panel shall be coil coated in a

continues paint line, double baked & roll

formed from stove enameled corrosion

resistant Aluminum Alloy AA 5050/3005 for

higher strength & roll forming characteristic.

The panels shall be clipped on to a Baked &

enameled Aluminum V-6 Stringer 33mm Wide

x 48mm Deep made from 0.95mm thick baked

& enameled Aluminum Alloy AA 5050 (Al.Mg)

in standard length of 5m in Black Colour with

cutouts to hold the panels in a module of

111mm C/C. The first stringers shall be fixed at

150mm from both ends & thereafter at a

distance of 0.75m to 1m depending on Wind

Load. The Stringer shall be fixed to a suitable

sub-structure / Wall with Nut/Bolt & Washer.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

PAINT FINISH: 84R Panels shall have Luxacoat®

exterior paint finish which will be of 3 layers.

1. The Anorcoat pretreatment,

2. The Colour Coating, &

3. Transparent Top Coat.

The paint used shall be expoxy based &

finished with a Polyamide / Nylon coating. The

Paint system shall have the following

characteristics:

1. COATING THICKNESS : 24-32 Microns

3. GLOSS VARIATION : +/-3 units (within

4. ADHESIVE IMPACT/BENDING : No loss of

5. PANEL HARDNESS : <HB

6. DURABILITY : Higher Category

7. HUMIDITY RESISTANCE : Blisters less than

LANDSCAPING & HORTICULTURE WORK - -

6.0 23.2 Supplying and stacking of good earth at site

including royalty and carriage up to 1 km (earth

measured in stacks will be reduced by 20% for

7.0 23.5 Rough dressing the trenched ground including

breaking clods.

8.0 23.7 Fine dressing of the ground 100 Sqm. - 220.00 -

9.0 23.10 Grassing with selection No.1 grass including

watering and maintenance of the lawn for 30

days or more till the grass forms a thick lawn,

free from weeds and fit for mowing including - -

supplying good earth, if needed (the good

earth shall be paid for separately).

9.1 23.10.1 In rows 5 cm apart in both directions 100 Sqm. - 1,052.00 -

10.0 23.10.2 With grass Turf 100 Sqm. - 793.00 -

11.0 U 46 Planting of trees ( Avenue plants) in 0.60m dia

holea, 1m deep dug in the ground, mixing the

soil with decayed farm yard/sludge manure.

This includes supply of labour, tools & plants

including materials but excluding cost of tree.

12.0 U 48 Supplying and Planting of different plant / trees

Supplying well grown plants bushy and healthy,

minimum height as specified i.e. exposed

height including all leads & lift, carriage, - -

handling, manuring, applying presticide and

fertilizer etc.

i ii Rangon chineese of size not less than 20cm

ii iv Rangon hi-breed healthy plant. Nos. - 23.00 -

iii v Duranta goldianna of size not less than 20cm

iv vi Duranta healthy plant of big size Nos. - 25.00 -

v viii China palm of leaves 4-5 in earthen pots size

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

vi xvi Adenium obesum of height 90cm-60cm in

earthen pots of size 25cm.

vii xix Bougainvillea (name variety, bushy plants, full

bloom) of height 90cm-60cm in cement pots of Nos. - 103.00 -

viii xx Croton (broad leaves) 3-5 branches of height

90cm-120cm in cement pots of size 30cm. Nos. - 148.00 -

ix xxi Croton different varieties of height 30 cm to 90

cm in earthen pots of size 25cm.

x xxiii Hibiscus Rosa Sinensis of height 90 cm to 60

cm in earthen pots of size 20 cm.

xi xxiv Hibiscus Rosa Sinensis of height 60 cm to 75

cm in earthen pots of size 35 cm.

xii xxx Dracaena Fragrance of height 90 cm to 60 cm

in earthen pots of size 35 cm.

xiii xxxiii Dracaena Reflexa of height 30 cm to 90 cm in

earthen pots of size 20 cm.

xiv xxxiv Dracaena Rosea of height 30 cm to 90 cm in

earthen pots of size 20 cm.

xv Supplying and planting different type foilage

and flowering shurbs (Canna, Jasmine, Ixora

etc) including pit making, manuring and

13.0 Seating Arrangements : - -

Circular table with bench consisting of 2 nos

base support, table of size 1000 mm dia x 50

mm thickness in terrazzo finish and 1 no bench

of size 1700 mm outer dia x 1200 mm inner dia No. 8.00 35,000.00 280,000.00

x 50 mm over all thickness in terrazzo finish.

Height of table 780 mm and ht of bench 450

Circular table with four bench consisting of 2

nos base support, table of size 1000 mm dia x

50 mm thickness in terrazzo finish and 4 no

bench of size 1000 x 350 mm x 50 mm thk in

terrazzo finish. Height of table 780 mm and ht

of bench 450 mm

Rectangular table with two benches consisting

of 2 no base support, 1 no table top of size

1500 mm length x 800 mm width x 50 mm thk

in terrazzo finish and 2 no benches osf size No. 8.00 30,000.00 240,000.00

1500 length x 325 width x 50 thk ht of table

780 mm ht of bench 450 mm

Chair bench with back rest consisting of 2 no L

shape base support in grey cement (Thk 100

mm, back ht 1000 mm, front ht 450 mm, base

width 620 mm) and 5 no reinforced concrete No. 8.00 15,000.00 120,000.00

planks in red colour of size 1500 x 100 x 50 and

1 no. rcc plank of size 1500 x 200 x 50

A CIVIL NS TOTAL 3,031,097.38

SANITARY INSTALLATIONS :

1.0 Providing and fixing single towel rack 600 mm

long with out lower hanger but with three

hooks having model no. ACN-1118FHN of

Jaguar make or equivalent.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

2.0 Providing and fixing toilet roll holder with flap

having model no. ACN-1153N of Jaguar make Each 121.00 975.00 117,975.00

3.0 Providing and fixing toilet towel ring square

with round flange having model no. ACN-

1121N of Jaguar make or equivalent.

4.0 Providing and fixing of required size beveled

edge mirror of superior glass (of approved

quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass

screws and washers complete.

5.0 Approved patent vent cowl C.I. conforming to

WATER SUPPLY : - -

1.0 Providing and fixing anglular stop cock with

wall flange having model no. LYR-38053 of Each - 1,000.00 -

Jaguar make or equivalent.

2.0 Providing and fixing soap dishpenser with

metallic bottle holder having model no. ACN-

1137N of Jaguar make or equivalent.

3.0 Providing and fixing two way bib cock with wall

flange having model no. ARI-39041 of Jaguar Each 121.00 1,700.00 205,700.00

make or equivalent.

4.0 Providing and fixing health faucet with one mtr

easy flex tube in crome finish and wall hook

having model no. ALD-CHR-565 of Jaguar make

5.0 Providing and fixing 450 mm long braided hose

with two 15 mm nuts and rubber washer

without nipple having model no. ALD-805B of

Jaguar make or equivalent.

6.0 Providing and fixing central hole basin mixture

with pop up waste system with 450 mm long

braided hoses having model no. CON-169KNB Each 101.00 3,100.00 313,100.00

of Jaguar make or equivalent.

7.0 Providing and fixing swan neck tap with left

hand operating knob with 450 mm long

braided hose having model no. CON-123BKN of

Jaguar make or equivalent.

8.0 Non Sch. Providing and fixing C.P. Wall Flange of

approved quality.

9.0 Non Sch. Providing & Installation including

commissionng & testng of suitable 5.0 H.P.

Open Well Submersible Pump (KSB or

Equivalent make) set including motor, starter,

base frame & coupling with bronze impeller & Each - 39,000.00 -

other accesseries of standard good quality to

fulfil the following performance, requirements

& specifications (For UGR to OHR).

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

10.0 Non Sch. Providing & Installation including

commissionng & testng of suitable 7.5 H.P.

Open Well Submersible Pump (KSB or

Equivalent make) set including motor, starter,

base frame & coupling with bronze impeller & Each 2.00 45,000.00 90,000.00

other accesseries of standard good quality to

fulfil the following performance, requirements

& specifications (For UGR to OHR).

A. CIRCUIT AND POINT WIRING (SUPPLY, INSTALLATION, TESTING AND COMMISSIONING)

1.0 NS Wiring for AC point with 4 sq. mm. Insulated

copper conductor 1100 volts grade stranded

flexible FRLS wires of approved make in

concealed minimum 2mm thick FRLS PVC

conduit (as per IS 9537 part 3) including

providing and fixing of 20 amps flush mounted

switch at the normal switch level in 1.6 mm

thick GI box and 32 amps 3 pin metalclad Pt 40.00 1,800.00 72,000.00

socket outlet with ON indicator with lockable

acrylic door and earthing of through the third

pin of the socket outlet and GI box with 2.5

sq. mm. PVC insulated copper conductor

flexible FRLS wire.

2.0 NS Wiring for Geyger point with 4 sq. mm.

Insulated copper conductor 1100 volts grade

stranded flexible FRLS wires of approved make

in concealed minimum 2 mm thick FRLS PVC

conduit (as per IS 9537 part 3) including

providing and fixing of 20 amps SP MCB in 1.6

mm thick GI box and32 amps 3 pin metalclad

socket outlet (IP 56) with On indicator with

lockable acrylic door and earthing of through

the third pin of the socket outlet and GI box

with 2.5 sq. mm. PVC insulated copper

conductor flexible FRLS wire.

3.0 NS Supply, laying, installation, testing and

commissioning of following PVC insulated

tinned copper conductor cable / wires in - -

existing cable tray / GI pipes / conduits.

3.1 10 pair 0.61 mm armoured cable Meter - 100.00 -

4.0 NS Supply and installation, testing and

commissioning following size KRONE make

telephone tag block in lockable 16 gauge sheet - -

steel enclosure complete as required.

4.1 10 pair tag box Each - 800.00 -

B. CABLES, MAINS AND SUB MAINS - -

1.0 NS Supplying of following 1100 volt grade XLPE

insulated PVC sheathed aluminium conductor

armoured cables as per specification.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

2.0 NS Supplying of following 1100 volt grade XLPE

insulated PVC sheathed copper conductor

armoured cable as per specification.

2.1 4 core 25 sq. mm. Metre - 550.00 -

3.0 NS Supplying of 2 core 2.5 sq.mm control cable for

Dual Metering arrangement including Metre - 90.00 -

C. CABLE TRAYS, RACEWAYS AND JUNCTION

1.0 NS Supply and installation of under floor GI

raceway with necessary hardware including of

supporting with threaded hitech rods etc.

1.1 200 mm wide x 40 mm deep raceway Metre - 650.00 -

1.2 150 mm wide x 40 mm deep raceway Metre - 500.00 -

2.0 NS Providing and fixing of 250 x 250 x 60 mm deep

(Nominal size) junction box including providing

3 mm thick GI steel cover required as per

3.0 NS Providing and fixing of 200 x 200 x 60 mm deep

(Nominal size) junction box including providing

3 mm thick GI cover required as per

F SUPPLY, INSTALLATION, TESTING AND

COMMISSIONING OF LIGHTING FIXTURES AND - -

Supply, Receiving, storing, installation &

handling of following lighting fixtures/ Ceiling

Fan/ Exhaust Fan with all fixing accessories etc.

1.0 NS Surface/ Suspended mounted commercial type

T-5 mirror optic luminaire including 2 x 28 Watt

TL-5 lamps, ballast and all accessories as

Philips Cat no. TCS150 2xTL5-28W M1 EBT

including 2 x TL5-28W lamp or equivalent.

2.0 NS Surface/ Suspended mounted commercial type

T-5 mirror optic luminaire including 1 x 28 Watt

TL-5 lamps, ballast and all accessories as

Philips Cat no. TCS150 1xTL5-28W M1 EBT

including 2 x TL5-28W lamp or equivalent.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

3.0 NS Surface/ Suspended mounted T-5 indoor

decorative luminaire including 1 x 28 Watt TL-5

lamps, ballast and all accessories as required.

Philips Cat no. MIROLTA Slim T5 TMS540 HF Each 471.00 550.00 259,050.00

including 2 x TL-5-28W lamp or equivalent.

4.0 NS Surface mounted commercial type down light

luminaire including 2 x 18 Watt PL-C compact

fluorescent lamps, ballast and all accessories as

Philips Cat no. FCS100 1xPL-C/2P18W I 240V

including 2 x PL-C-18W CF lamp or equivalent.

5.0 NS Surface mounted commercial type luminaire

including 2 x 11 Watt PL-s lamps, ballast and all

accessories as required. Philips Cat no. FCS031

2xPL-S/2P11W I 240V including 2 x PL-C-11W

CF lamp or equivalent.

6.0 NS Aesthetic Wall Mounted mirror light luminaire

suitable Philips: FMS 200/111 for 1x PL-5

9W/11W CFL Lamp with white refletor base

for higher light delivery.

7.0 NS Bulk Head lighting fixture Philips make FXC101

1xPL-S / 2P 9W AC GR or equivalent complete Each - 1,050.00 -

with PL-9 lamp.

8.0 NS 48" dia sweep ceiling fan (BEE 5 star rated)

with step type modular fan regulator of

approved make complete with all accessories.

9.0 NS Exhaust Fan 225 mm sweep (Heavy duty) .

G. SUPPLY, INSTALLATION OF LIGHTING

FIXTURES AND SUPPLY & INSTALLATION OF

CABLES FOR EXTERNAL/ LANDSCAPE

1.0 Suplying, Receiving, storing handling, installing,

testing and commissioning of the following - -

lighting fixtures.

1.1 Wall Mounting Light fixture Philips make HWS

360 I x PLC/2P18 GR or equivalent complete

with lamp, electric ballast etc as required.

1.2 Philips or equivalent make Bollard lighting

fixture Cat No. HPS 370 IX CDMTT-150W GR

with lamp and ballast as per requirement or No. 20.00 9,500.00 190,000.00

approved equal in quality .

1.3 Integral Post Top Lanterns Light fixture Philips

make CDS550 CDMT 150W C 240 V or

equivalent complete with lamp, electric ballast

etc as required.

1.5 4.0 M high poles MS decorative poles (3.0 M

above & 1 M below ground) Kesselec Make No. 244.00 10,000.00 2,440,000.00

Blenheim model or equivalent

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

1.6 Street Light fixture Philips make SGP401 I x

CDMTT- 150 W complete or equivalent

complete with lamp, electric ballast etc as

2.0 Providing and fixing of following PVC insulated

copper conductor 1100 volts grade stranded

flexible wire in GI conduit including providing

and fixing of conduit concealed or surface

mounted as indicated PVC insulated green - -

colour copper stranded flexible wire for

earthing and making connection complete.

2.1 3 x 4 sq.mm wire in 25 mm dia conduit. RM 1,568.00 320.00 501,760.00

2.2 3 x 2.5 sq.mm wire in 25 mm dia conduit. RM 882.00 290.00 255,780.00

3.0 Providing, installation, testing and

commissioning of 200 x 150 x 125 mm

polycarbonate weather proof (IP-55) junction

box recessed in wall or surface mounted as

required for housing of 1 no. 10 amps SPN Nos. - 4,300.00 -

MCB’s suitable size of terminal blocks

complete. Suitable length of GI pipe up to

junction box shall also be provided for laying of

4.0 Supply, installation, testing and commissioning

of following polycarbonate weather proof (IP-

55) junction box suitable for pole mounting / - -

underground complete as required.

I. MAIN LT PANEL, UTILITY PANELS AND DBs - -

1 MAIN LT DISTRIBUTION BOARD - -

A. Incoming: - -

A1 The Incoming Feeder from EB source should

have the following :

1000 amps 4P, 50 kA, electrically operated fully

draw out type air circuit breaker with

microprocessor release unit (Type 6.0A of MG

make or equivalent), for short circuit, over

current and earth fault protection with

adjustable setting as per specification and with

following accessories- 1 set :

i Digital load manager (conzerve – EM 6400 with

RS-485 or equivalent) of accuracy class-I with 2 - -

No. 3200/5 amps 15VA CTs.

ii Phase indicating lamps protected by 6 amps SP

iii Three Phase Under voltage relay MV12 or

equivalent (27) - 1 Set

iv Three Phase Over voltage relay MV 12 or

equivalent (59) - 1 Set

v Breaker ON/ OFF/ TRIP indicating lights with

control MCB’s- 1 Set

vi 24 V DC Shunt trip coil. - 1 Set - -

vii 240 V AC under voltage release. - 1 Set - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

viii Auto-manual / test selector / switch - 1 Set

ix Breaker control switch - 1 Set - -

x Auxiliary contacts required for necessary

interlocking of breakers.

xi Three phase Voltage sensor relay shall be

protected by 2 amps TP MCB’s- 1 Set

xii Transient voltage class B surge supressor (100

kA) (Lines to Neutral) & (Neutral to Earth) - -

suitable for 3 phases - 1 Set

xiii Digital voltmeter with inbuilt selector switch- 1

A2 The Incoming Feeder from DG source should

have the following :

1000 amps 4P, 50 kA, electrically operated fully

draw out type air circuit breaker with

microprocessor release unit (Type 6.0A of MG

make or equivalent), for short circuit, over

current and earth fault protection with

adjustable setting as per specification and with

following accessories- 1 set :

i Digital load manager (conzerve – EM 6400 with

RS-485 or equivalent) of accuracy class-I with 2 - -

No. 1000/5 amps 15VA CTs.

ii Phase indicating lamps protected by 6 amps SP

iii Breaker ON/ OFF/ TRIP indicating lights with

control MCB’s- 1 Set

iv 24 V DC Shunt trip coil. - 1 Set - -

v 240 V AC under voltage release. - 1 Set - -

vi Auto-manual / test selector / switch - 1 Set

vii Breaker control switch - 1 Set - -

viii Auxiliary contacts required for necessary

interlocking of breakers.

ix Three phase Voltage sensor relay shall be

protected by 2 amps TP MCB’s- 1 Set

x 0-500 volts digital electronic voltmeter with

selector switch and control MCB’s.

xi Grid supply voltage sensing relay. - -

xii Restricted Earth Fault Relay (L&T SC14S)

including all accessories.

B. Bus Bars - -

1500 amps TPN Aluminium bus bars with heat

shrinkable insulation sleeve. - 1 Set

C. Outgoing: - -

i. 800 amps 3 Pole manually, 50 kA, operated

fully draw out type air circuit breaker - with

built in microprocessor based release unit

(Type 2.0A of MG make or equivalent) for short

circuit, over current and earth fault protection - -

with adjustable setting and ON/ OFF/ Trip &

shunt trip coil etc. as per specification- 1 No.

ii Twenty five (25) - Outgoing feeders each

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

One(1) - 100A, TPN, 35kA, MCCB including

digital multi function meter with 100/5 amps - -

15 VA Cl: 1 CTs

iii One (1) - Outgoing feeders each having - -

400A, TPN, 35kA, MCCB including digital multi

function meter with 400/5 amps 15 VA Cl: 1 - -

iv Two (2) - Outgoing feeders each having - -

One(1) - 250A, TPN, 35kA, MCCB including

digital multi function meter with 250/5 amps - -

15 VA Cl: 1 CTs

i. All MCCB's shall be of 35 KA (Ics) breaking

ii All MCB's shall be of 10 KA breaking capacity.

iii. All the outgoing feeders shall have Direct / CT

operated Digital energy meter (Conzerve make

– EM 6400 or equivalent) of accuracy class-I.

MDB - 1 described as above. Set. 1.00 2,200,000.00 2,200,000.00

2 LIFT PANEL (MDB 3) - -

100 Amps TPN MCCB with following

VAF digital electronic meter with inbuilt

selector switch and 100/5 amps 15 VA, CL 1 - -

Phase indicating light shall be protected by 2

amps SP MCB's. - 3 Set

100 amps TPN 35kA for 1 sec aluminium bus

bars with heat shrinkable insulation sleeve. - 1 - -

Two (2) - Outgoing feeder having: - -

Three (3) - Outgoing feeders each having : - -

One (1) - 16A, SP, 10kA, MCB - -

One (1) - Outgoing feeder having : - -

One (1) - Plug top and industrial socket with

16A, DP, 10kA, MCB control.

All MCCB's shall be of 35 KA (Ics) breaking

All MCB's shall be of 10 KA breaking capacity.

Lift Panel (MDB 3) described as above. Set. 1.00 80,000.00 80,000.00

3 PLUMBING DISTRIBUTION PANEL (MDB 4) - -

Plumbing DistributionPanel (MDB 4) as

described above

4 AREA LIGHTING PANEL (MDB 5) - -

A Incoming - -

63 Amps TPN MCCB with following

a. 0-500 volts 96 x 96 mm square ammeter with

selector switch shall be protected by 2 amps - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

b. 0-100 amps 96 x 96 mm square voltmeter

with selector switch and 60/5 amps 10 VA CL:1 - -

c. Phase indicating lamps shall be protected by

2 amp SP MCB-3 Sets

B Bus Bar - -

100 amps TPN (25 KA) aluminium bus bar with

heat shrinkable insulation sleeves colour coded. - -

C Outgoing - -

i Two (2) - Outgoing feeder having: - -

One (1) - 20A, TPN, 10kA, MCB. - -

One (1) - 20A, TP, contactor with 2NO & 2NC

auxiliary contacts, supply voltage 240V, 50Hz,

single phase with 24hrs daily timer.

One (1) - 16A, TPN, 10kA, MCB - -

Six (6) - 10A, SP, 10kA, MCB - -

Area Lighting Panel (MDB 5) as described

5 Design, fabrication, assembling, wiring, supply,

installation, testing and commissioning of

Automatic control panels with mixed die

electric type capacitors, fabricated out of 14

gauge CRCA sheet steel in cubicle

compartmentised, 3b modular construction,

free standing, floor mounted, dust and vermin

proof with reinforcement of suitable size, angle

iron, channel, `T’ sections and/ or flats

wherever necessary. Cable gland plates shall be

provided on top the panels. Panels shall be

treated with all anticorrosive process before

powder coating as per specifications and final

approved shade. 2 No. earthing terminals shall

be provided for all distribution panels. Panels

shall be suitable for 415V, 3 phase, 4 wire, 50

HZ supply system. Lifting hooks shall also be

provided in case of large panels. Approval shall

be taken for each panel in the form of shop

drawings before fabrication. Galvanized

hardwares with zinc passivation shall be used

in fabrication of panels.

200 KVAR CAPACITOR PANEL - -

A. Incoming - -

800 amps TPN manually operated fully drawout

type air circuit breaker as per specification and - -

with following accessories:

96 x 96 mm sq. 0-500 Volt digital voltmeter with

selector switch

Phase indicating light shall be protected by 2

Amps SP MCB’s - 3 Set

B. Bus Bars : - -

1000 amps TPN Aluminium bus bars with

coloured heat Shrinkable insulated sleeves. - 1 - -

C. Outgoings: - -

i. Outgoings -I : - -

250 amps TPN MCCB - 2 Set - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

Outgoing feeders consisting of following

100 amps or capacitor duty 480 volts 50Hz

contactors. - 2 Sets

“ON” /”OFF” push buttons and indicating

lamps. - 2 Sets

50 KVAR, 480 volts capacitor unit - 2 Sets. - -

ii. Outgoings -II : - -

100 amps TPN MCCB - 2 Set - -

Outgoing feeders consisting of following

100 amps or capacitor duty 480 volts 50Hz

contactors. - 2 Sets

“ON” /”OFF” push buttons and indicating

lamps. - 2 Sets

25 KVAR, 480 volts capacitor unit - 2 Sets. - -

iii. Outgoings -III : - -

40 amps TPN MCCB - 5 Set - -

Outgoing feeders consisting of following

40 amps or capacitor duty 480 volts 50Hz

contactors. - 5 Sets

“ON” /”OFF” push buttons and indicating

lamps. - 5 Sets

10 KVAR, 480 volts capacitor unit - 5 Sets. - -

Capacitor Panel as described above Set. 1.00 500,000.00 500,000.00

6 FINAL DISTRIBUTION BOARDS - -

Supply, installation, testing and commissioning

of the following DB's fabricated out of 1.6 mm

thick CRCA sheet steel in cubicle

compartmentalized, dust and vermin proof,

double door construction, powder coated with

approved shade and partitions to segregate

phases. Approved lockable covers with

padlocking arrangement, recessed in wall or

surface mounted final distribution boards of

the following description:

6.1 Lighting & Power DB - -

8 way TPN DB, 24 No. 25 Amps SP MCB’s as

outgoing with 3 No. 63 Amps ELCB’s of 30 mA

leakage current and 1 No. 63 Amps 4 pole MCB No. 8.00 10,000.00 80,000.00

as incomer with separate neutral link for each

6.2 Residential Quarter DB - -

Supplying and fixing following way, horizontal

type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/

recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, - -

interconnections, powder painted including

earthing etc. and mending good all the

damages as required.

DB comprises - -

Ways- 12 way TPN - -

Incoming - 63 A FP MCB isolator - -

Outgoing - 12 Nos 6A-10A SP MCB with One

Nos 25A DP RCCB's (sensibility-30mA) in each - -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

i All MCB's shall be of 10 KA breaking capacity.

6.3 Emergency Lighting DB - -

8 way SPN DB, 8 No.10/ 16/ 20 Amps 'D' curve

SP MCB’s as outgoing with 1 No. 25 Amps DP

ELCB + MCB as incomer with separate neutral

link for each phase.

6.4 Supply and installation of 25A, 3 pin industrial

type socket outlet with SP MCB control

enclosed in sheet metal box with 25A plug top

wall mounted with necessary accessories

complete as required

6.5 Supply and installation of 10 nos. 0-20A

electronic energy meters in sheet steel

structure with lockable doors and glass window

opening as require. The fabrication and No. 28.00 27,000.00 756,000.00

installation of the supporting steel structre,

doors and other accessories shall include.

C. ELECTRICAL NS TOTAL 14,482,385.00

LIFT INSTALLATION

1.0 Supply, installation, testing & commissioning of

passanger elevator (capacity: 8 passanger

each) as required to complete the job in all

respect as per following technical specification.

Schindler 5300IN Gearless & Machine room

less, Elevator No. 00100

Clear Inside Shaft 1550 mm Width x 1650 mm

Rated Load 544 kg

Drive System Alternating Current Voltage

Frequency (ACVF)

Speed of travel 1.5 m/s

Car Size 1100 mm (W) x 1300 mm (D) x 2139

Rated output motor 6.9 kw

Car walls finish in Stainless Steel Hairline

Granite Flooring finish in Black Sea

Deco Ceiling finish in Stainless Steel Hairline

Full height mirror on rear car panel

2 Hours Fire rated landing doors

Automatic evacuation to nearest floor (ARD)

11 Stop 8 passanger Lift (G+10) Each 2.00 2,600,000.00 5,200,000.00

2.0 Supply, installation, testing & commissioning of

passanger elevator (capacity: 8 passanger

each) as required to complete the job in all

respect as per following technical specification.

Schindler 5300IN Gearless & Machine room

less Elevator No. 00300

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

Clear Inside Shaft 1550 mm Width x 1650 mm

Rated Load 544 kg

Drive System Alternating Current Voltage

Frequency (ACVF)

Speed of travel 1.0 m/s

Car Size 1100 mm (W) x 1300 mm (D) x 2139

Rated output motor 6.9 kw

Car walls finish in Stainless Steel Hairline

Granite Flooring finish in Black Sea

Deco Ceiling finish in Stainless Steel Hairline

Full height mirror on rear car panel

2 Hours Fire rated landing doors

Automatic evacuation to nearest floor (ARD)

5 Stop 8 passanger Lift (G+4) Each 1.00 1,865,000.00 1,865,000.00

D. LIFT NS TOTAL 7,065,000.00

A) FIRE HYDRANT , WET RISER , SPRINKLER

1.0 Supplying, installing, testing and

commissioning of M.S.ERW Pipes confirming to

IS 1239, Heavygrade with painting, suitable

type of supports (Shall be fabricated by M.S. .

Channel / Angle /Flat for above 50 mm dia),

anchor fasteners,bolts nuts, clamps, "U" bolt,

malleable specialssuch as Reducers, Tees,

elbows, flanges.Including cutting, Welding,

fixing in / on walls,ceiling by using suitable

supports etc, as perdrawings. The quoted rate

shall also include forchasing / chipping walls,

making bore holes inwalls / floor and making

them good with fillermaterial and finished in

cement mortar etc.complete.

1.1 250 mm dia ( 6.35 mm thick ) Metre - 3,092.00 -

1.2 200 mm dia ( 6.35 mm thick ) Metre - 2,602.00 -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

2.0 Supplying, installing, testing and

commissioning of M.S. ERW Pipes confirming

to IS 1239 Heavy grade with suitable type of

supports, malleable specials such as Reducers,

Tees, elbows, flanges. Including

cutting,Welding as per drawings. The rate - -

quoted should be included with anticorrosive

treatment with 4 mm thick "PYPKOTE" polymer

corrosion resistant tape as per IS 10221,

overlap shall be 15mm minimum.

2.6 65 mm dia Metre - -

2.7 50 mm dia Metre - -

2.8 40 mm dia Metre - -

2.9 32 mm dia Metre - -

2.10 25 mm dia Metre - -

3.0 Supply, erection, testing & commission of Cast

Iron double flanged Non Return Valve (IS :

5312) following sizes conforming to relevant IS

specifications and teted for a minimum

pressure of 16 kg / sq cm for sheet and 24 kg / - -

sq cm for sheel including providing and fixing

Nuts & Bolts gaskets. Washers etc complete as

4.0 Supplying fitting & fixing Sluice Valve PN 1.6 NB

Rising Stem conforming of approved brand and

make with companion flanges, nuts & bolts etc - -

all complete bearing IS 14846.

5.0 Supply, Installation, Testing, Commissioning of

CIDF Sluice valve with counter flange & nut - -

6.0 Providing, fixing, testing of Suction Strainer

with foot valve ,counter flange, nuts & bolts, Each - 20,590.00 -

gasket etc 250 mm dia

7.0 Providing , fixing , testing of SS oblique type

hydrant valve with 63 mm outlet GM

instantaneous female coupling with rubber cap

and chain conforming to IS ; 5290 including Each 27.00 7,532.00 203,364.00

matching flange, gasket, nuts and bolts

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

8.0 Providing and Fixing 63 mm dia rubberized

reinforced rubber line hose pipe in 15 m length

conforming to IS : 636 Type A ISI marked with

SS male and female instantaneous coupling Each 54.00 6,150.00 332,100.00

conforming to IS 903 wounded with 18 SWG

copper wire complete.

9.0 Providing and Fixing SS branch pipe with 20

mm nozzle conforming to Is 903 complete. Each 27.00 2,445.00 66,015.00

10.0 Providing , fixing, testing of swinging type hose

reel drum fabricated from 14 SWG CRCA sheets

painted with red color stove paint 2 coats over

1 coat of primer with 30 m long 20 mm dia Each 27.00 6,292.00 169,884.00

rubber hose pipe with 10kg / sqcm working

pressure with GM shut – off

11.0 Providing and Fixing M.S. hose box with

lockable arrangements to accommodate 2 RRL

hose of 15 m length and one branch pipe Each 27.00 3,095.00 83,565.00

painted white inside and red outside with one

12.0 Supplying fitting & fixing of pressure gauge

with half coupling nipple root valve adaptor, 3

way gauge cock vibration dampner as per

specification and direction of the E-I-C

complete in all respect.

13.0 Supplying erection testing & commissioning of

Electric Motor Driven Horizontal, centrifugal

fire pump of capacity 171 cum / hr at 100

MWC, 2900 RPM of approved make with

coupling & coupling guard, base frame as

necessary foundation in all complete as per

specification and direction of the E-I-C.

14.0 Supplying erection testing & commissioning of

Electric Motor Driven Horizontal, centrifugal

Jockey Pump of capacity 11 cum / hr at 100

MWC, 2900 RPM of approved make with

coupling & coupling guard, base frame as

necessary foundation in all complete as per

specification and direction of the E-I-C.

15.0 Supplying erection testing & commissioning of

Electric Motor Driven Horizontal, centrifugal

fire pump of capacity 171 cum / hr at 100

MWC, 1800 RPM of approved make with

coupling & coupling guard, base frame as

necessary foundation in all complete with

diesel engine of heat exchanger cooled of

approved make all complete as per

specificastion and direction of the E-I-C.

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

16.0 Supply, Installation,Testing ,Commissioning of

dust and vermin proof cubicle type motor

control centre fabricated from 14 SWG MS

sheet with powder coated finish comprising of

following : Incomer Main 400 Amp TPN

MCCB.One Fully taped 400 Amp TPN

aluminium busbar in seperate

chamber.One150 mm square panel type Volt

meter with selector switch. One 150 mm

square panel type Ammeter with C/T & Set 2.00 359,681.00 719,362.00

selector switch. Phase indicating lamps.

Outgoing : Two 250AmpTPN MCCB. One

63AmpTPN SFU with HRC fuses. Two fully

automatic star-delta Starter with push button

& on /off / trip indicating lamps for hydrant &

sprinkler pumps. One fully automatic D.O.L

Starter with push.

17.0 Providing and Fixing heavy duty PVC insulated,

PVC armoured aluminium conductor cables

1100 V grade including necessary support - -

clamps and connection lugs complete in all

17.1 Power cable 3 core X 70 mm2 Meter - 607.00 -

17.2 Power cable 3c X 10 mm2 Meter - 239.00 -

17.3 Control cable copper armoured, 2cX2.5mm2

18.0 Providing and fixing GI earthing strip 25mm x 6

mm thk. From all motors and MCC panel to be

connected in all approved manner to general job - 170.00 -

earthing system.

19.0 Providing and Fixing Gunmetal collecting head

with 63 mm dia instantaneous type inlet 150

dia flanged, outlet with built in check valve for

fire brigade connection to fire riser ( IS 904 )

20.0 Providing and fixing INDFOSS make pressure

switches for cut – out and cut in pressure with Each 5.00 4,166.00 20,830.00

21.0 Providing & fixing Installation Control Valve

alongwith trims, actuator, water motor gong,

Instruments & other accessories as required

22.0 Providing & fixing quartzoid bulb sprinkler 68 C

along with necessary attachment. Pendent Nos. 70.00 387.00 27,090.00

23.0 Supply, Installation,Testing ,Commissioning of

G.I.medium grade pipe IS-1239 part - I, with all

fittings supports and painting etc. Mtr. - 955.00 -

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

24.0 Providing and fixing carbon – di – oxide fire

extinguisher consisting of welded MS

cylindrical body, squeeze, lever discharge valve,

fitted with internal discharge tube, high

pressure discharge hose, discharge nozzle,

suspension bracket, finished externa.

Capacity 4.5 kg. ISI marked

25.0 Providing and fixing mechanical foam type ( ISI

marked ) fire extinguisher consisting of welded

MS cylindrical body, squeeze, lever discharge

valve, high pressure discharge hose, discharge

nozzle, suspension bracket ISI marked finished

externally with red

Capacity 9 liters

26.0 Supply, Installation, Testing , Commissioning of

ABC stored pressure type ( ISI marked )

extinguisher including all accessories with wall

bracket with rawl plug.

Capacity 6 kg. ISI marked

27.0 Providing & application of Anti-corrosive tape (

28.0 Supplying, fitting & fixing cast iron Air release

Valve of approved brand and make bearing ISI

Mark tested to 21 kg / sqcm

B) FIRE ALARM SYSTEM - -

1.0 Supply, Installation,Testing and Commissioning

of the following:-

1.1 Analog addressable low profile type photo

electric detector with mounting based LED,

Address switch, complete as required.

1.2 Analog addressable low profile type

multicriteria detector with mounting based

LED, Address switch, complete as required.

1.3 Electronic Hooter cum speaker for fire alarm /

evacuation signal, 6 watt capacity including Nos. 22.00 4,777.00 105,094.00

1.4 Break glass type manual call point with

necessary supports, chipping, chaising, civil

work , concealed work of cabling/conduit, Nos. 22.00 4,022.00 88,484.00

cable termination, gland, hammer with chain

Digitally signed by SILKI

Sl No. Description of Items Unit QTY RATE AMOUNT

2.0 Microprocessor based analog addressable type

fire alarm panel with loop card, auto detector

test, programmable switches, for modification

in programme, automatic alarm drift level

compensation, 240 volts AC power supply, 24

volts sealed battery & battery Charger,PA

Console, Amplifier,Microphone etc complete as

2.4 M.S. Conduit ( 20 mm) Mtrs - 124.00 -

3.0 Supplying fitting & fixing cabling complete with

lugs, laying inside conduits and termination of

both ends of ISI make approved quality as per

satisfaction of EIC. 2 C x 1.5 mm CUPVC FRLS

(Control & Power cable)

4.0 Fault isolator Nos 11.00 3,927.00 43,197.00

E. FF NS TOTAL 5,714,749.00

Extra Item (DSR 2014)

Providing and laying autoclaved aerated

cement blocks masonry with 100 mm thick AAC

blocks in super structure above plinth level up

to floor V level in cement mortar 1:4 (1 cement

: 4 coarse sand ). The rate includes providing

and placing in position 2 Nos 6 mm dia M.S.

bars at every third course of masonry work.

Add 10% as cost enhancement as DSR Item 54,117.39

Total EXTRA ITEM - (DSR) 595,291.33

Extra Item (NON DSR)

1 NS Providing and Driving of 6mm thick MS sheet

Liner for Cast-in-situ Pile.

M.S. Sheet Liner kg - 106.24 -

GRAND TOTAL (I) 69,569,922.48

GRAND TOTAL (I) 69,569,922.48

Digitally signed by SILKI