PROVN OF TOILETS, BATHROOM, URINAL, WASHING RAMP, PATHWAY, COVERED SHED, HARD STANDING, TILING AT DIFFERENT LOCATIONS AND ADDN/ALTN TO CERTAIN BUILDINGS AT SEVOKE ROAD MIL STATION

Amount

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0 kg of cement per sq metre all as specified and as directed.

Taking up or down 15 mm bore steel water tubing and connections complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.50 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplus soil to a distance not exc 50 m and making good surfaces in soft/loose soil complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas not exc 1.5 m in deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas exc 1.5 m but not exc 3 m in deep and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed.

Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface.

Materials and Labour for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in surface channel and drain including necessary formwork complete all as specified and as directed.

Materials and Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C-1, using 20mm graded stone aggregate as in cills, steps, coping, filling in cowkats, bed blocks, hold fasts and like complete all as specified and as directed.

Materials and Labour for formwork to chullah hoods, chajjas, cooking or other platform, troughs and similar items including edges Complete all as specified and as directed.

Materials and Labour for formwork to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

Materials and Labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished square, rectangular or polygonal surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc; basement slabs under reamed pillars and mass concrete complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in column, pillars, piers, post and struts complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for precast cement concrete louvres and jallies,(1:2:4) type B0 using 12.5 mm graded stone aggregate, 40mm thick (measured solid), including all mouldings, Set in cement mortar (1:4) complete all as specified and directed.

Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 5 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Materials and Labour for rolled mild steel Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and as directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde-E 165) complete all as specified and as directed.

Supply & fixing rolled mild steel section including hollow section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates FE-290 Gde E-165. Complete all as specified and directed.

Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 20mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for coloured 300x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for coloured 300x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for Vitrified Ceramic tiles of dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:6 complete all as specified and as directed.

Materials and labour for providing Virtified Ceramic tiles 10 mm thick (square/rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:4 complete all as specified and directed.

Materials and labour for Coloured Vitrified glossy tiles of 6 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors walls etc. set and jointed in neat cement slurry or fixing chemical and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:4 complete all as specified and as directed.

Materials and labour for chequered cement concrete tiles 20 cmx20cmx/30cm x 30 cm size, 25 mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed.

Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing complete.

Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 M-35 grade, laid as directed to any shape. Complete all as specified and as directed

Materials and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand Complete all as specified and as directed

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete even and rough complete all as specified and directed.

Materials and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate as in sub-base of floors etc. finished the surface of concrete even and rough complete all as specified and directed.

Materials and labour for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded stone aggregate as in sub-base of floors, plinth protection etc. finished the surface of concrete fair and even, complete all as specified and directed.

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in floors, plinth protection, path etc. finished the surface of concrete even and smooth smooth without using extra cement, complete all as specified and directed.

Materials and labour for brick work with fly ash bricks modular size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:4 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for Pre-cast cement concrete block masonry with solid blocks of PCC (1:2:4) type B1 using 20 mm graded stone aggt, exc. 10cm in width, straight or curved on plan to any radius built in cement mortar 1:4 complete all as specified and as directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

Supply and fixing Solid PVC wall lining consisting of 5mm thick single side prelaminated PVC sheet, inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

Supply and fixing 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification complete all as specified and directed.

Supply and fixing 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified.

Materials and labour for Second class hard wood in scantlings, clean swan, timber framed and fixed, complete all as specified and as directed.

Supply and fixing flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing 30mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

Materials and labour for 19mm thick plywood grade BWR,type BB fixed with screws to timber frame work as in cup board ,fix with brass screws and cups complete all as specified.

Materials and labour for 18/19mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work as in cabinet, cup board,moduler kitchen etc. including external teak wood lipping all round, 6mm thick fixed with nails complete all as specified.

Materials and labour for 1.5 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions. Make:- Green ply industries Ltd/ Century/ Archid.

Supply and fixing Aluminium (Extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

Supply and fixing 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fixing anodised powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Supply and fixing anodised powder coated aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws, handles 2 nos in each door,hinges, including supply and fixing 5.5 mm thick tinted glass complete all as specified and directed

Supply and fixing anodised powder coated aluminium window and ventilator shutter, fixed type, without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc., including supply and fixing 5.5 mm thick tinted glass complete all as specified and directed

Supply and fixing coloured aluminium anodised louvers ventilator of frame size 63.5x38.1x1.01mm or higher section with aluminium members of suitable size for holding glass strips including necessary locking arrangement, 4mm thick frosted glass strips etc. complete all as specified and directed

Supply and fixing powder coated aluminium (minium thickness of powder coating 50 micron) sliding windows incl frame of size 65x28x1mm or higher section, shutters of size 20x40x1mm or higher section including poviding and fixing 5.00 mm thick glass pane, roller , handle , locking arrangement, neoprene gasket etc , CP brass/stainless steel screws incl silicone sealant wherever required complete all as per specified and directed by the Engineer-in-charge

Supply and fixing stainless steel butt hinges, 100 mm size , complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 100 mm long, complete all as specified and directed.

Supply and fixing for 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing Aluminium handles, cast type, anodized, 125 mm size , complete all as specified and directed.

Supply and fixing Aluminium handles, cast type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing MS butt hinges medium weight 75mm long, complete all as specified and directed.

Supply and fixing MS butt hinges medium weight 100mm long, complete all as specified and directed.

Supply and fixing in repair continuous (Piano) hinges mild steel bright finish or electro galvanised, width of flaps when open 30mm complete as specified and directed.

Supply and fixing 2 lever brass lock, cupboard grade 1, 50mm size complete as specified and directed.

Supply and fixing stainless steel 02 Lever door lock of approved make complete as specified and directed.

Supply and fixing stainless steel 04 Lever door lock of approved make complete as specified and directed.

Supply and fixing 40mm dia, cupboard knobs, brass, polished fixed with nut, screw and washer of mild steel, bright finished complete as specified and directed.

Supply and fixing CP curtain rails 20 mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete al as specified and directed.

Supply and fixing decorative type wooden finish double brackets support for holding curtain rods and corners to be fixed to ends of curtain rod, fixed with screws complete all as specified and directed.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete without glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fixing steel ventilators with top hung shutter including hinges,steel peg stay, including one shop coat of Zinc Chrome primer complete all as specified and directed.

Supply and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 3 mm thick figured glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 5mm thick in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only integral Water Proofing Compound of approved make.

Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

Materials and labour for applying three coats of white wash on new ceiling surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces and applying two coats of cement based paint over a coat of cement primer on wall complete all specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of plastic emulsion paint (superior quality) of approved colour with roller over one coat of primer over 1 mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer over 1mm thick wall care putty complete all as specified and directed.

Materials and labour for complete removal of existing paint from surfaces of wall and applying two coats of weather proof antifungal exterior emulsion paint (as per manufacturer instructions) of approved colour over a coat of alkali resistant primer over 1mm thick wall care putty complete all as specified and directed.

Materials and labour for complete removal of existing paint from surfaces of wall and applying two two coats of plastic emulsion paint (superior quality) of approved colour with roller over one coat of primerr over 1mm thick wall care putty complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer over 1 mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 2.5 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 2.5 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick non asbestos fibre cement boards of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion distemper over a coat of primer including preparation of surfaces complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Cutting of existing steel tubing for alterations or additions (Each cut measured) in any position for insertion and fitting of new Tee, Coller, Tail pieces etc for taking out connections, branch connections complete all as specified and directed for 40/50 mm bore pipe.

Supply and fixing 15 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 20 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 25 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing stainless steel sink with drainage board, 1 mm thick for kitchen or laboratoty with plugs, waste pipe, washers, including cantilever cast iron brackets, connecting union to waste pipe etc including bedding in cement mortar to dwarf wall, overall size 915x460mm with bowl size 410mm x 330mm x160mm with 40 dia mm CP waste coupling and PVC waste pipe complete all as specified and directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with CP brass bracket guard railing 60cm long complete all as specified and directed.

Supply and fixing Vitreous China wash down water closet pan (pedestal pattern), white with "P" or "S" Trap front or back inlet fixing bolts, PVC seat cover complete and making all necessary connection as specified and directed.

Supply and fixing Snow White vitreous china wash down water closet pan (pedestal pattern) 'S' Trap One piece EWC 'S' concealed including soft close seat cover, internal twin flush fittings and making all necessary connection as specified and directed.

Supply and fixing Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) incl setting the trap and pan in cement mortar (1:3:6) all round and "P" or "S" Trap, complete all as specified and directed.

Supply and fixing 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fixing vitreous china, white, flat back wash hand basin of size 525 mm x 415 x 140 mm thin Rim counter top basin including counter with jet black granite with and including CP brackets (of suitable size) including 32 mm bore brass chromium plated waste coupling, 32 mm dia PVC waste pipe etc complete all as specified and directed.

Supply and fixing Vitreous China wash hand basin, white, flat back, size 550x400mm, including waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, brackets, with and incl 32/40mm dia 90cm long PVC waste down pipe, includind S&F cromium plated Pillar taps 15 mm bore, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe but excluding taps complete all as specified and directed.

Supply and fixing vitreous china bowl urinal flat back size 355 x 340 x 535 mm white (minimum) with gratings and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipes) etc all as directed and specified by Engr-in-Charge. (Make:Jaquar Cat No. URS-WHT-13261 or equivalent model of Hindware/Parryware/Cera)

Supply and fixing Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including CP Spreader , flush pipe and waste pipe complete all as specified and directed.

Supply and fixing for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

Supply and fixing Bip tap standard of PTMT any colour screwed for iron pipe and fixed (Minimum weight 15mm - 90gms complete all as specified and as directed.

Supply and fixing 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, long body, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing Concealed 15 mm bore angular stop valve cast copper alloy fancy type chromium plated with long shank and cup (concealed type) with capstan head wall flange etc screwed down screwed for iron pipe complete all as specified and directed. .

Supply and fixing cromium plated Pillar taps, fancy type with long neck, 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, complete all as specified and directed.

Supply and fixing in repair 15 mm bore centre hole sink mixer cast copper alloy with capsten head, chromium plated fancy type screwed down high pressure with letter hot and cold with long screwed shank and flynuts screwed for iron pipe, complete all as specified and directed.

Supply and fixing 15mm bore dia Stop cock cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing 15mm bore dia two way bib taps cast copper alloy chromium plated, fancy type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and as directed.

Supply and fixing CP Soap dish holder including CP screws complete all as specified and as directed.

Supply and fixing CP Soap dispenser with glass bottle including CP screws complete all as specified and as directed.

Supply and fixing CP Towel ring, square type including CP screws complete all as specified and as directed.

Supply and fixing CP Toilet paper holder including CP screws complete all as specified and as directed.

Supply and fixing Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed.

Supply and fixing in repairs CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

Supply and fixing in repairs CP brass overhead shower 80mm dia round shape with and including CP brass shower arm 240mm long with wall flange complete all specified and directed.

Supply and fixing in repairs brass chromium plated, shower rose, 125mm size complete all as specified and directed.

Supply and fixing in repair stainless steel tubular drapery rod 28mm dia as specified and directed.

Supply and fixing stainless steel brackets for drapery rod 28mm dia as specified and directed.

Supply and fixing stainless steel knobs for drapery rod 28mm dia as specified and directed.

Supply & fixing CI Floor trap 100mm diameter of outlet, with gratings, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as directed.

Supply and fixing 32mm bore Bottle trap of chromium plated having minimum water seal of 25mm .

Supply and fixing 150mm dia DWC PE pipes (SN-8), ISI marked, in any length jointed and laid in trenches or in floors, complete all as specified and directed.

Supply and fixing 100mm dia DWC PE pipes (SN-8), ISI marked, in any length jointed and laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore complete all as specified and directed.

Supply and fixing PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and laying Salt-glazed stoneware (SWG) drain pipes, 150mm dia, laid in trenches and jointed as specified complete all as specified and directed.

Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fixing Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply and fixing ball brass valves of size 25 mm bore high pressure, with polythene float and fly nut, screwed for iron pipe etc complete all as specified and directed.

Supply and fixing in repair 25 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Materials and labour for concealed point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete.

All as per Item No.179 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps.

Supply and fixing Switch socket combination multipurpose 5 A/16 Amps,5 in 1, flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 65x50mm all as directed.

Supply and fixing energy saving and environmental friendly long life LED security/street Light fittings 25 watts, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover, IP 66 protection, inbuilt driver, connecting with suitable size copper wire, with 32mm bore 1 m long medium grade GI bracket made to shape complete all as specified and as directed.

Supply and fixing new decorative type surface and wall mounted 20 Watt LED batten light fittings, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing new decorative type surface and wall mounted 9/10 Watt LED box type light fittings, 2 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply, fixing and connecting exhaust fan metal body with louvers shutter, voltage 230V, 50 Hz, Copper winding of sweep 230mm, including drilling holes in wall for fixing and connecting with suitable size copper wire complete all as specified and as directed.

Supply and fixing MCB distrubution board SPN 8way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB distrubution board SPN 4way, double door, IP 42, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB Single pole, 240 volts 5 to 32 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB Double pole, 240volts 32 Amps, 10KA rupturing capacity, C series

Supply and laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 10 Sqmm 2 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed complete all as specified and as directed.

Materials and labour for clear sand cushioning for protection of cable complete all as specified and directed. (only punned down thickness to be measured)

Supply and laying fly ash bricks of traditional size as in cable protection complete all as specified.

Materials and labour for GI pipe medium grade with all fittings complete grouted in ground all as specified for 40 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable complete all as specified and directed.

Supply and fixing electric water heater (Geyser),storage type, 25 lits capacity, BEE 5 star rating, complete all as specified and directed.

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x5 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

TAPASH SAHA