Package 1 Civil Work Package of Manjra dam Dist Beed (Rehabilitation, Improvement and Basic facilities of Manjra Dam in Beed

Amount

PART – A (Work Portion)

Item No.1:- Labour charges for removing grass, thorny shrubs, Jungli shurb, Kubabul and alike grass along and in the drain/canal making the ground clean by showel and phavaras etc. complete as directed by Engineer - in - charge.

Item No.2:- Removing wet silt from canal bed with 15.00 m lead and all Lifts including depositing the excavated stuff etc. Complete as directed by Engineer - in - charge.

Item No. 3:- Excavation in all kinds of soil including boulders upto 0.6 m diameter (0.113 cum) for canal, seating of embankment, filter drains / catch water drains etc., and placing the excavated stuff neatly in dump area or for formation of service road / embankment as directed including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc., complete with lead upto 1 km and all lifts as directed.

Item No.4 A :- Providing and constructing 300 mm thick dry rubble stone pitching with pin headers at 2 per sqm using stones and stone chips from approved source including cost of all materials, labour, hand packing / wedging stone chips, finishing etc. Complete with lead upto 50 m and all lifts as directed by Engineer-in-charge.

Item No.4 B :- Providing and constructing 300 mm thick dry rubble stone pitching with pin headers at 2 per sqm using stones and stone chips from approved source including cost of all materials, labour, hand packing / wedging stone chips, finishing etc. Complete with lead upto 50 m and all lifts as directed by Engineer-in-charge.

Item No.5:- Providing, installing & erecting in correct line and level, fiber glass reinforced plastics (FRP) "V notch" of following sizes and discharge capacities, for accurate measurment of water flowing through open channel with prefabricated fiber glass lining moulded engraved gauge marking ( in lit/sec and in cms) including discharge table, capacity marking, flow direction, sand treatment on the back side of " V" notch, testing, etc complete, as directed.

Item No :6 - Excavation for catch / side water gutter in all sorts of soils to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed all sorts of soils.

Item No 7 :- Providing and laying 300 mm dia. half round white glazed earthenware pipes in 1:5:10 cement concrete bedding including bends, etc. complete.

Item No. 8 : Providing and laying in situ cement concrete of grade M-20 of trap / granite / gneiss / quartzite / graded metal for RCC works of RCC works of abutment, wing walls, returns, transition walls, piers, columns, eams and slabs, diaphram walls, road slabs trough (Box Culvert) trough for aqueduct, wearing coat, etc. . with Batching Plant and Transit mixer including centering, shuttering, scaffolding, lacing compacting, curing etc. complete with all lifts as directed.

Item No 9 : Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete as directed.

Item No 10 : Providing structural steel work in rolled section, like joists, channels, angles, tees etc. as per detailed design and drawing as directed including cutting, fabricating, hoisting, errecting, fixing in position making riveted/bolted/welded connections without connecting plates, braces etc. and including one coat of anticorresive paint and over it two coats of oil painting of approved quality and shade etc. complete

Item No.11:- Supplying hard murum/ kankar at the road site, including conveying and stacking complete

Item No.12 :- Spreading hard murum/ soft murrum/ gravel or kankar for side width complete

Item No.13 :- Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete

Item No 14 :- Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means - Grading II (Using Screening Type B (11.2 mm) Aggregate)

Item No 15 :- Providing and constructing 75 mm. thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 mm. stone metal layers 30% crusher broken metal + 70% Hand broken (by breaking rubble obtained by blasting) heating and spraying the bitumen of specified grade @ 2 Kg/sqm, spreading 12 mm.size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete. Including picking of existing WBM surface. (VG-30 bulk bitumen rates are considered to arrive at rates)

Item No 16 : Providing bituminous Type A liquid seal coat on bituminous surface including supplying all materials and bitumen of specified grade preparing existing road surface, heating and applying bitumen @ 0.98 KgSqm. by mechanical means, spreading chips and rolling, by static roller having weight 8 to 10 MT. etc. complete. (VG30 bulk bitumen rates are considered to arrive at rates)

Item no 17 : Open Graded Premix Surfacing- Providing and Laying OGC 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates premixed with bituminous binder transported to site with VTS , laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired compaction but excluding prime / tack and Seal coat. For Bitumen of specified grade--USING drum mix type hot mix plant with SCADA, Paver and Vibratory roller ( Over MPM Surface) (VG-30 bulk bitumen rates are considered to arrive at rates)

Item no 18 : Providing and applying tack coat on the prepared surface heating by flames in Boiler and spraying bitumen with sprayer on Granular surface treated with primer @ 2.75 kg/10 sqm(VG-30 bulk bitumen rates are considered to arrive at rates

Item No 19: Providing railing of mild steel angle post 2.0m center to center of section 75mm x 75mm x 10mm or equivalent I/C section of height 1.05 above bridge surface with minimum anchor length of 30cm including hold fast of 25mm diameter MS bar welded at the bottom and concreting of 1:3:6 of size 30cm x 30cm x 30cm with three rows of 40mm B class GI pipe provided at 30cm on center to center including scaffolding and one coat of anticorrosive paint with two coats of oil painting, curing of concrete etc. complete.

Item No.20 :- Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete as directed by Engineer Incharge

Item No.22:- Dismantling R.C.C. works and removing the stuff to a distance of 15 m and all lifts including stacking etc. complete

Item No.23:- Providing and laying expansion / construction joint with 18 SWG copper plate and shalitex expansion pad below and above the copper plate including sealing the joint with shalitex sealing compound including 50 x 50 x 5 mm angle frame with stainless steel bolts etc as directed. (For all thickness)B) 37.50 Cm. wide copper plate

Item No.24:- Excavation in all kinds of soil including boulders up to 0.6 m diameter ( 0.113 cum) for canal, seating of embankment, filter drains / catch water drains etc., and placing the excavated stuff neatly in dump area or for formation of service road / embankment including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. Complete with lead up to 1 km and all lifts as directed.

Item No.25:- Providing and laying rubble soling below foundation in layers including filling with rubble chips, murum etc. complete as directed

Item No.26:- Providing and laying in situ cement concrete of grade M-15 of trap / granite / gneiss / quartzite / graded metal for foundation and bedding by Batching Plant & Transit Mixer including centering,shuttering, scaffolding, placing, compacting, curing etc. complete with all lifts as directed. (A) M-15 (20 MSA) (Cement 5.64 bags/Cum)

Item No.27:- Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete as directed

Item No.28:- Providing and laying expansion / construction joint with 18 SWG copper plate and shalitex expansion pad below and above the copper plate including sealing the joint with shalitex sealing compound including 50 x 50 x 5 mm angle frame with stainless steel bolts etc as directed. A) 60 Cm. wide copper plate

Item No.29:- Providing and laying cement plaster 6 mm thick in C.M. 1:3 single coat without neru finish to concrete surface in all position including centering, scaffolding, curing etc. complete as directed. (Cement 0.057 bags/Sqm)

Item No.30:- PICC filling for Honey combing area at concrete surface:-Providing and applying Poly Ironite Ceramic Cementitious (PICC) material of Self cureing ,High Abrasion resistant , Non shrink ,High strength,UV resistant, repair mortar coating on Kelox water missble epoxy of concrete surface fill the honey combing area etc. on tacky primer coat upto 10 mm thickness or as per the surface conditions including Cleaning the concrete surface of bridge by grinding the surface by grinder machine with wire brush /diamond wheel, removing existing loose particles etc. by using grinder, wire brush,breaker machine, water jet(using other mechanical / manual means) also removing of algae fungi by special chemical of clonon. etc.complete with all leads and lifts, Material, Machinery, Labour, Scaffolding etc. complete as per specification and as directed by engineer-in-charge.

ITEM No.31 : Providing pointing with cement mortar for stone masonry including racking joints, scaffolding, curing etc. complete as directed. (B) In Cement Mortar 1:2

ITEM NO. 32 : Core Strengthening of Concrete Structure:Strengthening of concrete structure including grouting of concrete with epoxy, AC-DUR-IE, as detailed in the method statement. Item includes cost of material, labour, equipment‘s and also removal of nozzles and finishing of the surface after the work

Item No 33 : Providing pointing with cement mortar for stone masonry including racking joints, scaffolding, curing etc. complete as directed. (B) In Cement Mortar 1:2

Item No 34 :- Providing and fixing 40mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Item No 35 :- Providing, installing & erecting in correct line and level, fiber glass reinforced plastics (FRP) "V notch" of following sizes and discharge capacities, for accurate measurment of water flowing through open channel with prefabricated fiber glass lining moulded engraved gauge marking ( in lit/sec and in cms) including discharge table, capacity marking, flow direction, sand treatment on the back side of " V" notch, testing, etc complete, as directed. (Excluding base preparation ie CBL, canal section other concrete etc.) (a) FRP V notch having discharge capacity 15 lit/sec of section 20 x 40 cms with upstream and downstream channel

Item No 36 :- Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Item No 37 :- Painting letters upto 20 cm height complete brushes, coir brushers, dusting, cleaning, including cost of paint etc. complete

Item No 38 :- Providing and fixing Road junction / Information sign board of size 1.20 m x 0.90 m. prepared on 16 gauge M.S. sheet with angle iron frame of size 35 x 35 x 5 mm with cross bracing of size 35 x 35 x 5 mm including painting with one coat of zinc cromate stoving primer and two coats each of green/white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border / letters / numeral /arrows, coated with non pealable crystal clear protective transperent coat retaining 100% reflection includingtwo angle iron post of size 65 x 65x 6 mm of 3.65 m. long inflated at bottom drilled on top and painted in whiteand black bands of 30 cm. with 4 Nos. high strength G.I. bolts and nuts of size 10 mm dia. and 20 mm long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with M-20 cement concrete of 60 cm x 60 cm x 75 cm size as directed by Engineer-in- charge etc. complete. Mild Steel sheet with Engineering grade.

ITEM NO.39 : Drilling 75 mm dia hole in masonry / rock by core drilling from foundation gallery floor at required depth including flushing the hole including conveying all machinery equipment & necessary dewatering etc complete.

Item No 40-a : Cleaning by redrilling the vertical porous drain pipe including removing of leaching material, grout material if any inside of the V.P.D. with all leads and lifts etc complete as directed. (Vertical upward drilling)a) 0 to 5 m

Item No 40 -b : Cleaning by redrilling the vertical porous drain pipe including removing of leaching material, grout material if any inside of the V.P.D. with all leads and lifts etc complete as directed. (Vertical upward drilling) b) 5 to 10 m

Item No 40-c : Cleaning by redrilling the vertical porous drain pipe including removing of leaching material, grout material if any inside of the V.P.D. with all leads and lifts etc complete as directed. (Vertical upward drilling) c) 10 to 15 m

Item No 40-d : Cleaning by redrilling the vertical porous drain pipe including removing of leaching material, grout material if any inside of the V.P.D. with all leads and lifts etc complete as directed. (Vertical upward drilling) d) 15 to 20 m

Item No 41: Dismantling the old lime concrete or cement concrete including stacking the material with all lifts etc.complete as directed

Item No 42 : Providing and laying expansion / construction joint with 18 SWG copper plate and shalitex expansion pad below and above the copper plate including sealing the joint with shalitex sealing compound including 50 x 50 x 5 mm angle frame with stainless steel bolts etc as directed. B) 37.50 Cm. wide copper plate

Item No 43 : Providing & applying of Epoxy Mortar layers to Monolith joint of Masonry Dam with all lift etc. complete as directed. ( Specification section 11.24)

Item No 44 : Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising without box

Item No 45 : Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No 46 : Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Item No 47 : Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No 48 : Providing and Fixing and errecting, welding 8 mm MS bar @200 mm c/c both ways for ferrocement walling with welded mesh of size 100x100x2.30 mm and chiken mesh 3 layers as directed

Item No 49 : Providing and casting Ferrocement wall in CM 1:3 including curing etc complete as directed.A - 30 mm thick wall

Item No 50: Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No 51: Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No 52: Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete

Item No 53: Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (Without mechanical gear)

Item No 54: Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means

Item No 55: Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Manual Means

Item No 56: Providing and laying in situ / ready mix / ready mix M25 RCC work with trap/ granite/ quartzite/ gneiss metal in well steining including shuttering, compacting by vibrating, finishing and curing etc. complete. (fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant / pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc ), excluding reinforcement)

Item No 57: Providing, cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete

Item No 58 : Excavation in hard rock of all toughness by breaker including boulders above 0.6 m dia.(0.113Cum) minimising damage to side slopes of excavation and placing the excavated rock neatly in approved dump area including cost of all materials, machinery, labour, levelling bed etc., complete with lead upto 1 km and all lifts as directed.

Item No 59: Labour charges for removing grass, thorny shurbs, Jungli shurb, Kubabul and alike grass along and in the drain/canal making the ground clean by showel and phavaras etc. complete as Directed.

Item No 60: Dismantling the old lime concrete or cement concrete including stacking the material with all lifts etc.complete as directed.

Item No 61: Excavation in all kinds of soil including boulders up to 0.6 m diameter ( 0.113 cum) for canal, seating of embankment, filter drains / catch water drains etc., and placing the excavated stuff neatly in dump area or for formation of service road / embankment including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. Complete with lead up to 1 km and all lifts as directed.

Item No 62 :- Providing and laying rubble soling below foundation in layers including filling with rubble chips, murum etc. complete as directed

Item No.63 :- Providing and laying in situ cement concrete of grade M-15 of trap / granite / gneiss / quartzite / graded metal for foundation and bedding by Batching Plant & Transit Mixer including centering,shuttering, scaffolding, placing, compacting, curing etc. complete with all lifts as directed. (A) M-15 (20 MSA) (Cement 5.64 bags/Cum)

Item No. 64 : Providing and laying in situ cement concrete of grade M25 of trap / granite / gneiss / quartzite / graded metal for RCC works of gallery, sluice, spillway crest, spillway down stream face, energy dissipating structures, intake structures, training walls, piers, abutments, slab etc. with Batching Plant and Transit mixer including centering, shuttering, scaffolding, placing, compacting, curing etc. complete with all lifts etc. complete as directed.

Item No 65: Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete as directed

Item No.66 : Removal of plants / ficus grown by pulling out root system embedded in masnory, cutting stem and application of high/gur/lime formulation as specified by the Architect or other patented chemical biocide treatment such as biocide 'Glycel' (iso proplamine salt of glyphosate) or other chemical as specified by the Engineer in charge etc. complete.

Item No.67 :- Cleaning grass and removal of rubbish up to a distance of 50 meters outside the periphery of the area as directed.

Item No.68 :- Removing wire fencing with iron/ C.C. fencing post and stacking the materials as directed with all leads, lifts etc. complete.

Item No 69 : Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Item No.70 : Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt.

Item No.71 :- Excavation in all kinds of soil including boulders up to 0.6 m diameter ( 0.113 cum) for canal, seating of embankment, filter drains / catch water drains etc., and placing the excavated stuff neatly in dump area or for formation of service road / embankment including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. Complete with lead up to 1 km and all lifts as directed.

Item No.72:- Providing and laying rubble soling below foundation in layers including filling with rubble chips, murum etc. complete as directed

Item No.73:- Providing and laying in situ cement concrete of grade M-15 of trap / granite / gneiss / quartzite / graded metal for foundation and bedding by Batching Plant & Transit Mixer including centering,shuttering, scaffolding, placing, compacting, curing etc. complete with all lifts as directed. (A) M-15 (20 MSA) (Cement 5.64 bags/Cum)

Item No.74:- Providing and laying in situ cement concrete of grade M-25 of trap / granite / gneiss / quartzite / graded metal for RCC works of RCC works of abutment, wing walls, returns, transition walls, piers, columns, beams and slabs, diaphram walls, road slabs trough (Box Culvert) trough for aqueduct, wearing coat, etc. . with Batching Plant and Transit mixer including centering, shuttering, scaffolding, placing, compacting, curing etc. complete with all lifts as directed.

Item No.75 :- Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete as directed.

Item no 76:- Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means.

Item No. 77 - Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete.

Item No. 78 : Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.

Item No. 79: Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

ITEM NO 80 :- Providing and laying in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

ITEM NO 81:- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

Item No. 82 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

Item No 83 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

Item No.84 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (crush sand VSI Grade)

Item No.85 :- Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.86 :- Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Item No.87 :- Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Item No.88 :- Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Item No.89 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No.90 :- Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete.

Item No.91:- Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.

Item No.92:- Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish

Item No.93:- Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Item No.94:- Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. Complete

Item No.95:- Providing and fixing Country cut teak wood single leaf panelled door shutters 35 mm thick style and rail and 19 mm thick T.W. panels as per detailed drawing including wrought iron hold fast stainless steel fixtures and fastening and three coats of oil painting etc. complete.

Item No.96:- Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Item No.97:- Providing sills of required material 20 mm to 25 mm thick,on a bed of cement mortar 1:4 including cement float ,filling joints with neat cement slurry, curing, moulding edges, polishing, cleaning complete. b) Granite

Item No.98 :- Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating with box

Item No.99 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Item No.100 :- Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

Item No.101:- Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Item No.102 :- Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32mm size of approved make including soil pipe, vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cutting and making good walls, floors etc. complete..

Item No.103:- Providing and fixing Orissa type white glazed earthenware water closet pan of size 260mm x 440mm x 580mm with approved make Slim wall hung cistern with installation kit including S or P trap with cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc.complete.

Item No.104:- Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5 liters flushing cistern with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 mm diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall.

Item No.105:- Providing and fixing white glazed earthenware Wash Hand Basin of 45cm x 30cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Item No.106:- Providing and fixing 10 cm pvc nahani trap with grating etc complete

Item No.107:- Providind and fixing on wall / ceiling / floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.108:- Providing and laying in trenches 25 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.109:- Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.110:- Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

Item No.111:- Providing and fixing shower head, with shower arm of approved make mixer of including all necessary pipe fittings and connections etc complete as directed by engineer incharge.

Item No.112:- Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

Item No.113:- Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means

Item No.114:- Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Item No.115:- Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No.116:- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No.117:- Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.118 :- Providing 2nd class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth of external walls including bailing out water, striking joints on unexposed faces, racking out joints on exposed faces and watering complete.

Item No.119 :- Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .

Item No.120:- Providing and fixing factory made solid core flush door shutters in double leaves 35mm thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 – 1966 (Revised) including approved face veneers on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening stoppers and finishing with french polishing etc. (Excluding door frame)(Sample to be got approved from Ex. Engineer before use) a)Commercial Hard Wood shutter

Item No.121 :- Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising without box

Item No.122 :- Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No.123 :- Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square

Item No.124 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No.125 :- Providing internal cement plaster 20 mm thick in a single coat in cement mortar 1:4 without neeru finish to concrete, brick surfaces in all positions including scaffolding and curing complete.

Item No.126 :- Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of 1:4 cement mortar including cement float, filling joints with slurry, curing polishing and cleaning etc. complete.

Item No.127 :- Providing and laying Vitrified mirror/glossy finish having decorative type of size 590 millimeter to 605 millimeter x 590 millimeter to 605 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc . complete.

Item No.128:- Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No.129 :- Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No.130 :- Providing & laying in situ cement concrete of M 10 proportion with trap/ granite/ quartzite/ gneiss metal in foundation including necessary form work compacting and curing etc. complete. with reversible Drum Type mixer with SCADA. With crushed sand

Item No.131 :- Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete

Item No.132 :- Providing and fabricating structural steel work in rolled sections like joists, channels,angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted/welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Item No.133 :- Providing and fixing Orissa type white glazed earthenware water closet pan of size 260mm x 440mm x 580mm with approved make Slim wall hung cistern with installation kit including S or P trap with cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc.complete.

Item No.134 :- Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Item No.135 :- Providind and fixing on wall / ceiling / floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.136 :- Providing and laying in trenches 25 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.137 :- Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

Item No.138 :- Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

Item No.139 :- Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller.

Item No.140 :- Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Item No.141 :- Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram / Running metre. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating with box

Item No.142 :- Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Item No.143 :- Providing and fixing white glazed earthenware Wash Hand Basin of 45cm x 30cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Item No.144 :- Providing and fixing 10 cm pvc nahani trap with grating etc complete

Item No.145 :- Providind and fixing on wall / ceiling / floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.146 :- Providing and laying in trenches 25 mm dai. CPVC pipe including necessary excavation, fittings. Refilling trenches etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.147 :- Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.148 :- Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge.

Item No.149 :- Supplying, installing, testing and commissioning of ETC solar water heating system without heat exchanger type of 200 LPD capacity complete. Specification no. ESD-SHWS-FPC

Item No.150 :- Providing and fixing factory made panelled door shutter in single leaf 35 mm thick style and rail without ventilator with CCTW panels 12 mm thick including wrought iron hold fast and stainless steel fixtures with oil painting 3 coats etc. complete.

Item No.151 :- Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat

Item No.152 :- Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc.complete

Item No.153 :- Replacement of damaged Mortise Lock of approved quality and make to door shutter including Removing and Refixing with Necessary screw, making proper adjustment for smooth operation etc. complete as per sample approved by Engineer in-chareg.

Item No.154 :- Supplying, installing, testing and commissioning Solar street light pole comprising of 12W LED luminaire, 12.8V- 30Ah Li battery, with 75Wp Solar panel, MS Powder Coated Battery Box weatherproof, mounted on 75/80 mm dia. BGrade GI Pole of 6 Mtr. height (5m above ground & 1m below ground), 12W LED Chip of luminaire should be in compliance to IES: LM-80 & Performance parameters of luminaire shall be as per IES LM-79:2008 Or IS 16106 : 2012); along with brackets, foundation, earthing and necessary accessories complete as per MNRE specification (With 5 Years warrantee).

Item No.155 :- Supplying and erecting centrifugal water pump (monoblock), 230 v, single phase 50 cycles A.C. supply of 0.75 kw/1 HP with discharge 1.6/2.9 litres/second for head 9/22 m & 40 mm suction/ 40 mm delivery pipe on provided C.C foundation as per specification no. WP-CGP.

Item No.156 :- Providing and erecting 1.2 meter high wire fencing with five rows of barbed wire supported on mild steel angle ( 50 x 50x 6mm) post at 2.5 m c/c including excavation of pits of foundation concrete fixing the posts in ( 1:4:8) cement concrete block of 45x45x45 cm and fastening the Wires and painting the angles with one coat with red lead primer and two coats of oil painting etc.complete

Item No.157 :- Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery

Item No.158 :- Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.

Item No.159 :- Executive's Table @ 1800L X 900D X 750HT Providing & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing

Item No.160 :- Supplying and erecting LED 20w tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Item No.161:- Supplying & erecting mains with 2x1.5 sq.mm FR copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WGMA/BW

Item No.162 :- Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.163 :- Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per BWspecification No: WGMA/

Item No.164 :- Supplying and erecting One/Two way piano type switch 6A./bell push erected on filled polypropylene board or double polished wooden board/ folded or screwed board with top of either wooden/ 3 mm thick hylam sheet/ 4mm thick plywood pasted with 1.5 mm thick laminate with S M screws and duly connected.

Item No.165 :- Supplying and erecting shockproof 3 pin plug socket 6A with porcelain base / flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden / 3 mm thick hylam sheet/ 4mm thick plywood pasted with 1.5 mm thickLaminate with S M screws and duly connected.

Item No.166 :- Supplying and erecting shockproof 3 pin plug socket 16A with porcelain base/ flush type erected on filled polypropylene ISI marked (IS:14772-2000) board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3 mm thick hylam sheet/ 4mm thick plywood pasted with 1.5 mm thick Laminate with S M screws and duly connected.

Item No.167 :- Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Item No.168 :- Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 modules duly erected.

Item No.169 :- Wiring for plug on board with Switch socket, copper wiring and earthing as per specification No: WG-PW/SW

Item No.170 :- Point wiring for light/fan/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch,earthing and required accessories as per specification No: WGPW/HW

Item No.171 :- Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.172 :- Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

Item No.173 :- Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Item No.174 :- Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete.

Item No.175 :- Removing cement tiles,or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Item No.176 :- Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complet

Item No.177:- Providing second class Burnt Brick masonry with conventional / I.S. type bricks in cement mortar 1:4 including scaffolding, racking out joints and watering etc. in pillar of rectangular shapes as shown in the drawings or as directed complete.

Item No.178 :- Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete.

Item No.179 :- Providing and applying Two coats of wallcare Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Item No.180 :- Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Item No.181 :- Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Item No.182 :- Providing and applying plastic emulsion paint of approved quality,colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (excluding the primer coat)etc.complete.

Item No.183 :- Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 135921992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete

Item No.184 :- Providing and applying required coats of a water based UV resistant Evercrete Top Seal sealant to protect natural stone,bricks,concrete and wooden structures from water intrusion and staining due to water penetration and algue formation etc complete.

Item No.185 :- Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall

Item No.186 :- Providing and fixing 34 mm thick moulded door shutter consisting of solid core single leaf flush door of 30mm thickness lipped with 15mm (5mmx3) thick x 30mm width on one style and top rail and 10mm (5mmx2) thick x 30mm width on other style and bottom rails. The inner panels laminated with 2mm thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 design in different plain and/or prelim colours on one side after routing the moulded design on flush doors and 2 mm plain and/or prelam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etc.as per direction of Engineer in charge and manufacturers specification and drawing etc.complete

Item No.187 :- Providing & Arrangemnt of High Back Chair-TILT MECHANISM WITH MULTILOCKING, HIGHDENSITY CUSHIONON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT.

Item No.188 :- Providing & Arrangemnt of Mid Back, ECOCTS Mechanism, Fixed Armrest, Gaslift for Seat height adjustment,Standard 5-prong P/Nylon Base with Fabric Upholstery

Item No.189 :- Executive's Table @ 1800L X 900D X 750HT Providing & Fixing of Table@1800L X 900D X 750HT-TOP & GABLEEND to be made of Membrane finish with soft waterfall edges & curved panel & Decorated Anodized section MODESTYPANEL to be made of 18mm thick Prelaminated particle board with PVC edge band as per drawing

Item No.190 :- Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750x450x2100Ht, with 4 adjustable shelves,Complete body&shutter made in 0.8mm thick & Top in 2mm thick CRCA, 4 Shutter to be mounted with the help of cuphinges,and 4 adjustable levelers,enitre storage in powder coated finish with 60 to 80 microns as as per drawing.

Item No.191:- Providing and fixing 20 mm dia. Screw down bib/stop tap of brass including necessary socket union nut complete.

Item No.192:- Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.193:- Providing and fixing on walls/ceiling/floor25mm dia. CPVC pipe with necessary fittings ,remaking good the demolished portion etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete.

Item No.194 :- Providing and laying in trenches 25mm dai.CPVC pipe including necessary excavation,fittings.Refilling trenches etc.complete.Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.195 :- Providing and fixing Orissa Pan of size580x445x260mm with approved make flush valve including trap,C.I.soil and vent pipe upto outside face of wall including 100mm dia.C.I.plug,bend and necessary pipe connection, etc complete. As directed by Engineer in charge.

Item No.196 :- Providing and laying for 225 mm dia. Salt glazed S.W. Pipe including fitting such as bends,tees,single junction,double junctions laying, jointing (including excavation and refilling the trenches) complete

Item No.197 :- Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking an spreading as directed,dewatering,preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc.complete. (Lift upto 1.50 m) By Manual Means

Item No.198 :- Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight 75 mm thick R.C.C. cover medium duty 100 kg etc. complete.

Item No.199 :- Providing and fixing 10cm C.I.Nahani Trap including C.I.grating bendand piece of C.I. pipe upto the outside face of the wall complete.

Item No.200 :- Providing and fixing 75 mm dia stabiliser pipe/P.V.C.soilvent/wastepipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc.

Item No.201 :- Providing and fixing white glazed earthen ware Wash Hand Basin of 45cmx30cm size including cold water pillar tap/cold and hot water pillar tap brackets,rubber plugs and brass chain,stop tap and necessary pipe connection including P.V.C.wastepipe and trap upto the outside face of the wall.Making good the damaged surface, testing etc. complete.

Item No.202 :- Providing and laying ceramic tiles of having size30cm.x30cm.and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Item No.203 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Item No.204 :- RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material,wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge

Item No.205 :- Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete

Item No.206 :- Supplying and erecting Electronic Type cordless call bell erected on T.W. board having portable bell push working on 9V D.C. battery and (effective range upto 45 meter) bell on 250 V A.C. supply.

Item No.207 :- Supplying, installing, testing and commissioning of 5 kWp OFF-GRID solar power pack with interconnecting wires / cables up to 24V pure sine wave solar power inverter (THD<3%), SPV Modules (335 WP X 15 Nos.), C-10 rated lead acid battery bank 24V, 300Ah x 4 nos. (12V, 300 Ah x 8 nos) suitable for 4 Hours backup with suitable MS powder coated stand to hold battery bank and keeping sufficient space for filling distilled water, canopy box to house inverter and other electronics, wiring up to solar inverter in casing and capping, display board, sign board, two distinct earthing, spike type lightning arrester, necessary accessories complete with 5 years ON-SITE warranty and fully comprehensive maintenance contract as per specification no. ESD-RT-OFG

Item No.208 :- Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Item No.209 :- Spreading hard murum/ soft murrum/ gravel or kankar for side width complete

Item No.210 :- Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.

Item No.211:- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.212 :- Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaning etc. complete. (using 100% crushed sand)

Item No.213 :- Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean.Applying Asian / Berger / Nerolac / Duuex Paints or equivalent wall primer with brush with mineral turpentine with brush 8 to 10 % and oil 15 to 20 % with roller and allowing to dry for aperiod 6 to 8 hours .Applying Asian / Berger / Nerolac / Dulex Paints or equivalent Acrylic wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours.Scrapping with Emery paper 180 and wipe clean.Applying Asian / Berger / Nerolac / Dulux Paints or equivalent wall primer with brush with mineral turpentine 8 to 10 % and oil 15 to 20 % with roller Scrapping Emery paper 320 and wipe clean, Applying Asian / Berger / Nerolac / Dulux Paints or equivalent interior wall finish luster 1st coat with brush / rubber / spray with mineral turpentine 7 to 9 % and Oil with roller 19 to 21 % After 8 hours of activity Applying 2nd coat of Asian / Berger / Nerolac / Dulux Paints or equivalent interior wall finish Lustre with mineral turpentine 7 to 9 12% with brush and Oil with roller 19 to 21 % after allowing dry for the period of 6 to 8 hours activity.(Withprior approval of S.E.)

Item No.214 :- Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating with boxcomplete.

Item No.215 :- Providing and fixing Modular false ceiling of 600x600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T2”x1½” (50mmx40mm) weighing 0.39kg/mat 60 cms center center and fixed with ½”x½” (15x15mm) flanges weighing 0.19kg/m suspended on 6mm diamild steel rod weighing 0.22kg/m, fixed on wall and beam sincluding rounding of theedges with alluinium T of 2”x1½” (50mmx40mm) weighing 0.39kg/metc.(allalluminium sections shall be anodized ) including alllabour, material, lifts etc. complete.

Item No.216 :- Providing and laying Vitrified MATT finish having decorative type of size 600 millimeter x 600 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete.

Item No.217 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No.218 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-15 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) (Rate will be reduced accordingly if Regular Plywood centering permitted instead of Steel Centering )

Item No.219 :- Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Item No.220 :- Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed design and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/ bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete

Item No.221 :- Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc.complete

Item No.222 :- Providing and fixing corrugated glavanised iron sheets of 0.63mm thick (24 B.W.G.) for roofing without wind tiles including fastening with galvanisediron screws and bolts, lead and bitumin washers as per drawing etc. complete, (Weight of 5.5 kg/Sqm.)

Item No.223 :- Providing and Laying cement concrete flooring 40mm thick with M20 cement concrete laid to proper level and slope in alternate bays,including compaction, filling joints marking lines to give appearance of tiles pf 30cmx30cm or other laid diagonally/squre etc. Finishing Smooth

Item No.224 :- Filling plinth and floors with contractors material/ brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete

Item No.225 :- Providing and fixing steel frame door of angle 50 x 50 x 6 mm with mild steel bars 16 mm dia. horizontally at 10mm c/c for ventilator portion including iron hold fast boxes for fixing shutters including welding, finishing, painting etc. complete.

Item No.226 :- Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 m x 2.40 m with aluminium door frame of powder coated section 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails 47.62 x 44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , with bijagiri having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length tower bolts, 150mm diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc. complete

Item No.227 :- Supplying, fixing and commissioning MCB type change over switch 4 pole, 63A with 3 positions (I-O-II) with centre off position as per specification no. SW-SWR/MCBCOS

Item No.228 :- Supplying, erecting & terminating XLPE armoured cable 4 core 95 sq. mm. copper conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Item No.229 :- Excavation in all kinds of soil including boulders up to 0.6 m diameter ( 0.113 cum) for canal, seating of embankment, filter drains / catch water drains etc., and placing the excavated stuff neatly in dump area or for formation of service road / embankment including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. Complete with lead up to 1 km and all lifts as directed.

Item No.230 :- Dismantling R.C.C. works and removing the stuff to a distance of 15 m and all lifts including stacking etc. complete.

Item No.233 :- Providing and constructing 300 mm thick dry rubble stone pitching with pin headers at 2 per sqm using stones and stone chipps from approved source including cost of all materials, labour machinary, hand packing/ wedging stone chips, finishing, etc., complete with lead upto 1 km and all lifts as directed. a) New material Utilization -

Item No.233 :- Providing and constructing 300 mm thick dry rubble stone pitching with pin headers at 2 per sqm using stones and stone chipps from approved source including cost of all materials, labour machinary, hand packing/ wedging stone chips, finishing, etc., complete with lead upto 1 km and all lifts as directed. b) Old material Utilization -

Item No.234 :- Providing and constructing 150 mm thick Quarry Spalls of approved trap stone quality of specified thickness from approved source including cost of all materials, labour, machinary etc.complete with lead upto 1 km and all lifts as directed.

Item No.235 :- Electrification Work (Vigilance, Security Building )

TOTAL : PART – A (Work Portion)