Construction of Multipurpose Hall at Jawahar Navodaya Vidyalaya, Deogarh, Odisha

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Earth work in excavation by mechanical

means (Hydraulic excavator) / manual

means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on

1 plan), including dressing of sides and

ramming of bottoms, lift upto 1.5 m,

including getting out the excavated soil and

disposal of surplus excavated soil as

directed, within a lead of 50 m.

Filling available excavated earth (excluding

rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding

20cm in depth,consolidating each deposited

layer by ramming and watering, lead upto

50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand

under floors, including watering,

ramming,consolidating and dressing

Excavating, supplying and filling of local

earth (including royalty) by mechanical

transport upto a lead of 5km also including

ramming and watering of the earth in layers

not exceeding 20 cm in trenches, plinth,

sides of foundation etc. complete.

Anti termite treatment

Supplying chemical emulsion in sealed

containers including delivery as specified.

Chlorpyriphos emulsifiable concentrate of

Diluting and injecting chemical emulsion for

POST-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical

Along external wall where the apron is not

provided using chemical emulsion @ 7.5

litres / sqm of the vertical surface of the

6 2.35.1.1 substructure to a depth of 300mm including 98.03 Metre 38.90 3813.44

excavation channel along the wall & rodding

etc. complete: With Chlorpyriphos/ Lindane

E.C. 20% with 1% concentration

Treatment of soil under existing floors using

chemical emulsion @ one litre per hole, 300

mm apart including drilling 12 mm diameter

holes and plugging with cement mortar 1 :2

(1 cement : 2 Coarse sand) to match the

existing floor:

With Chlorpyriphos/Lindane E.C. 20% with

1% concentration

B Concrete Work

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work

up to plinth level 1:5:10 (1 Cement : 5

coarse sand (zone-III) derived from

natural sources : 10 graded stone aggregate

nominal size derived from natural sources)

Providing and laying damp-proof course

40mm thick with cement concrete 1:2:4 (1

cement : 2 coarse sand (zone-III) derived

from natural sources : 4 graded stone

aggregate 12.5mm nominal size derived

from natural sources)

Extra for providing and mixing water

proofing material in cement concrete work in per 50kg

doses by weight of cement as per cement

manufacturer's specification.

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing & applying a coat of residual

petroleum bitumen of grade of VG-10 of

approved quality using 1.7kg per square

metre on damp proof course after cleaning

the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of

cement concrete 1:3:6 (1 cement : 3 coarse

sand (zone-III) derived from natural sources

: 6 graded stone

aggregate 20 mm nominal size derived from

12 4.17 natural sources) over 75mm thick bed of dry 127.94 SQM 749.30 95865.44

brick ballast 40 mm nominal size, well

rammed and consolidated and grouted with

fine sand,including necessary

excavation,levelling & dressing & finishing

the top smooth.

Brick edging in full brick width and half brick

depth including excavation, refilling and

13 16.7.1 disposal of surplus earth lead upto 50 170.58 RM 194.30 33143.69

metres. With common burnt clay F.P.S. (non

modular) bricks of class designation 7.5

C Reinforced Cement Concrete

Centering and shuttering including strutting,

14 propping etc. and removal of form for all

Foundations, footings, bases of columns,

etc. for mass concrete.

Suspended floors, roofs, landings, balconies

and access platform.

Lintels, beams, plinth beams, girders,

Columns,Pillars, Piers, Abutments, Posts and

Edges of slabs and breaks in floors and walls

Under 20 cm wide.

Extra for additional height in centering,

shuttering where ever required with

adequate bracing, propping etc., including

cost of de-shuttering and decentering at all

15 5.11.1 levels, over a height of 3.5 m, for every 515.16 SQM 384.30 197975.99

additional height of 1 metre or part thereof

(Plan area to be measured).

Suspended floors, roofs, landing, beams and

balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

16 5.22.6 placing in position and binding all complete 16352.35 KG 107.85 1763600.95

upto plinth level. Thermo-Mechanically

Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

17 5.22.A.6 placing in position and binding all complete 27860.90 KG 107.85 3004798.07

above plinth level. Thermo-Mechanically

Treated bars of grade Fe-500 D or more.

Add for plaster drip course/ groove in

18 5.30 plastered surface or moulding to R.C.C. 664.02 RM 74.40 49403.09

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and laying in position ready mixed

or site batched design mix cement concrete

for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana /

Ordinary Portland /Portland Slag cement,

recommended proportions as per IS: 9103 to

accelerate / retard setting of concrete, to

improve durability and workability without

impairing strength; including pumping of

concrete to site of laying, curing, carriage

19 5.33 for all leads; but excluding the cost of

centering, shuttering, finishing and

reinforcement as per direction of the

engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the

minimum specified cement content in design

mix shall be payable separately. In case the

cement content in design mix is more than

110% of the specified minimum cement

content, the contractor shall have discretion

to either re-design the mix

or bear the cost of extra cement.

(I) 5.33.1 All works upto plinth level

Concrete of M25 grade with minimum

cement content of 330 kg /cum

Concrete of M30 grade with minimum

cement content of 350 kg /cum

5.33.1.2 (iii) R.C.C. work in Columns 20.71 CUM 9655.70 199969.55

(II) 5.33.2 All works above plinth level upto floor V level

Concrete of M25 grade with minimum

cement content of 330 kg /cum

Concrete of M30 grade with minimum

cement content of 350 kg /cum

5.33.2.2 (iii) R.C.C. work in Columns 54.32 CUM 10011.35 543856.58

D Masonry Work

Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class

20 6.13.2 designation 7.5 in superstructure above 171.57 Sqm 1123.80 192810.37

plinth level up to floor V level.Cement

mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2

21 6.15 Nos 6mm dia. M.S. bars at every third 171.57 SQM 104.80 17980.54

course of half brick masonry.

Brick work with non modular fly ash bricks

conforming to IS:12894, class designation

10 average compressive strength in

superstructure above plinth level up to floor

V level in : Cement mortar 1:6 (1 cement :

Brick work with common burnt clay F.P.S.

(non modular) bricks of class

23 6.1.2 designation 7.5 in foundation and plinth in: 104.88 CUM 7132.25 748030.38

Cement mortar 1:6 (1 cement : 6 coarse

Random rubble masonry with hard stone in

foundation and plinth including levelling up

24 7.1 with cement concrete 1:6:12 (1 cement : 6

coarse sand : 12 graded stone aggregate 20

mm nominal size) upto plinth level with :

Cement mortar 1:6 (1 cement : 6 coarse

F Cladding Work

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills ,

facias and similar locations of required size,

approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching

pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete

Providing edge moulding to 18mm thick

marble stone counters, Vanities etc.

26 including machine polishing to edge to give

high gloss finish etc. complete as per design

approved by Engineer-in-Charge.

Extra for fixing marble /granite stone over

and above corresponding basic item, in facia

27 8.4 and drops of width upto 150 mm with epoxy 79.50 RM 568.55 45199.73

resin based adhesive including cleaning etc.

Extra for providing opening of required size

& shape for wash basins/ kitchen sink in

kitchen platform, vanity counters and similar

28 8.5 location in marble/Granite/stone work 8.00 EACH 978.70 7829.60

including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of

cut edges etc. complete.

Providing and fixing Ist quality ceramic

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in white

cement mixed with pigment of matching

shade complete.

(Size-300x450 )

Providing and Fixing of Acoustical Wall Panel

with square edges made of fibre glass

substrate 25mm thick, wrapped on the front

side with an acoustically transparent fabric

as per the approved shade (Husk, Copper,

Sangria, Sesame, Coffee, Charcoal,

Titanium, Flame, Peanut and Shell). The

panel shall be classified for Fire Class A, as

per ASTM E-84. The Acoustical Wall Panel

shall be of sizes 600x600mm (Nominal) or

600x1200mm (Nominal) and shall achieve

an NRC of 0.85 (Average value of Absorption

Co-efficient readings taken at 250 Hz, 500

Hz, 1000 Hz and 2000 Hz) with 50mm airgap

as per ASTM C423 to be fixed to wall on a

framework of wooden battens and using Wall

panel Impalers (supplied by the

manufacturer) or by using construction

adhesives (as per the instructions laid down

by the manufacturer). The fibre glass

substrate shall have a recycle content of

85%. Properties of Tile Relevant Standards

Base Material Fibre Glass

Panel Dimensions 600mm x 600/1200mm

Panel Thickness 25mm

Panel Finish Acoustically transparent fabric

as per the approved shade (Husk,

Copper, Sangria, Sesame, Coffee, Charcoal,

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing & fixing of 100% Natural Material-

Magnesite (Hygroscopic & biologically sound

binding agent) bonded woodwool Panel

planks of 600Mm*1200Mm *25Mm thickness

made out of wood wool fibre of width 1Mm

Fiber thickness mixed with Natural water &

Magnesite (No-Cement) with open & smooth

surface texture. A Completly harmless

Envirenment & Human Friendly & also a

disposable or recyclable Material & can last

for long span in building interiors As it has

long lifespan & suitable for Indoor conditions

with relative air humidity of upto 90%.

Magnesite protects the wood cells against

ageing & fungal attack. To achive upto

NRC=1.00 it should be a clear gap of 200Mm

from wall slab along with the backing of

Mineral of 50kg/m3. Edge Detail : AK 01

Heradesign Woodwool - Acoustical Wall

Mounting System Solutions- Ecologically

Material with high mechanical strength with

Crash test of 90Km/H with Ball Impact Test

DIN18032 & EN13964 with flying colors & A

sustainable material (PEFC & FSC Certified)

along with EPD Certified Acc. to EN ISO

14025 (AUB-Environmental Product

G Wood and PVC Work

Providing and fixing panelling or panelling

and glazing in panelled or

panelled and glazed shutters for doors,

windows and clerestory windows (Area of

opening for panel inserts excluding portion

inside grooves or rebates to be measured).

Panelling for panelled or panelled and glazed

shutters 25 mm to 40 mm thick :

9.7.7 Float glass panes

5.0 mm thick glass panes (weight not less

than 12.50 kg/sqm).

Providing and fixing Fiber Glass Reinforced

plastic (FRP) Door Frames of cross-section

90 mm x 45 mm having single rebate of 32

mm x 15 mm to receive shutter of 30 mm

thickness. The laminate shall be moulded

with fire resistant grade unsaturated

33 9.121 polyester resin and chopped mat. Door 76.05 RM 570.95 43420.75

frame laminate shall be 2mm thick and shall

be filled with suitable wooden block in all the

three legs. The frame shall be covered with

fiber glass from all sides. M.S. stay shall be

provided at the bottom to steady

30 mm thick Fiberglass Reinforced Plastic

(F.R.P.) flush door

shutter in different plain and wood finish

retardant grade unsaturated polyester resin,

mm thick FRP laminate all around, with

suitable wooden

blocks inside at required places for fixing of

polyurethane foam (PUF)/Polystyrene foam

filler material throughout the hollow panel,

monolithically with testing parameters of

F.R.P. laminate

conforming to table - 3 of IS: 14856,

complete as per direction

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and fixing factory made uPVC

white colour casement/ Casement cum fixed

glazed door comprising of uPVC multi-

chambered frame, sash and mullion (where

ever required) extruded profiles duly

reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll

forming process of required length (shape &

size according to uPVC profile), uPVC

extruded glazing beads of appropriate

dimension, EPDM

gasket, zinc alloy (white powder coated) 3D

hinges and one handle on each side of

panels along with zinc plated mild steel multi

point lockinghaving transmission gear,

cylinder with keeps and one side key, G.I

fasteners 100 x 8 mm size for fixing frame

to finished wall and necessary stainless steel

screws, etc. Profile of frame & sash shall be

mitred cut and fusion welded at all corners,

mullion (if required) shall be also fusion

welded including drilling of holes for fixing

hardware's and drainage of

water etc. After fixing frame the gap

between frame and adjacent finished wall

shall be filled with weather proof silicon

sealent over backer rod of required size and

of approved quality, all complete as per

Casement door with top hung ventilator with

friction hinges (400 x 19 x 1.9 mm) made of

frame 67 x 64 mm, sash 67 x 110 mm &

mm all having wall thickness of 2.3 ±. 0.2

single glazing bead / double glazing bead of

dimension.(Area of door upto 2.50 sqm)

Providing and fixing fire resistant door frame

of section 50 x 60 mm on horizontal side &

35 x 60 mm on vertical sides having built in

rebate made out of 1.6 mm thick GI sheet (

Zinc coating not less than 120gm/m²)

suitable for mounting 120 min Fire Rated

Glazed Door Shutters. The frame shall be

filled with Mineral wool Insulation having

density min 96Kg/m³ . The frame will have a

provision of G.I. Anchor fastners 14 nos ( 5

36 9.161 each on vertical style & 4 on horizontal style 42.60 RM 2202.90 93843.54

of size M10 x 80 ) suitable for fixing in the

opening along with Factory made Template

for SS Ball Bearing Hinges of Size

100x89x3mm for fixing of fire rated glazed

shutter . The frame shall be finished with a

approved fire resistant primer or Powder

coating of not less than 30 micron in desired

shade as per the directions of Engineer - in-

charge . (Cost of SS ball bearing hinges is

Providing and fixing 60 mm thick glazed fire

resistant door shutters of 120 min Fire

Rating confirming to IS:3614 (Part II) or

tested and certified as per laboratory

approved by Engineer-in-charge, with

suitable mounting on door frame, consisting

of vertical styles, top rail & side rail 60 mm

x 60 mm wide and bottom rail of 110 mm x

60mm made out of 1.6mm thick G.I. sheet

(zinc coating not less than120gm/m²) duly

filled mineral wool insulation having density

min 96 kg/m³ and fixing with necessary

stainless steel ball bearing hinges of

size100x89x3mm of approved make,

including applying a coat of approved fire

resistant primer or powder coating not less

than 30 micron etc all complete as per

direction of Engineer-in-charge (panelling to

be paid for seperately).

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and fixing glazing in fire resistant

door shutters, fixed panels & partitions etc.,

with G.I. beading made out of 1.6 mm thick

G.I. sheet (zinc coating not less than 120

gm/m²) of size 20 x 33 mm screwed with M4

x 38 mm SS screws at distance 75 mm from

the edges and150 mm c/c , including

applying a coat of approved fire resistant

primer/powder coating of not less than 30

micron on G.I. beading, & special ceramic

tape of 5 x 20 mm size etc complete in all

respect as per NBC 2016, IS 16231 (Part

3):2016 and as per direction of Engineer-

incharge with glass of required thickness

having 120 minutes of fire resistance both

integrity & radiation control (EW120) and

minimum 20minutes of insulation (EI20).

The manufacturer have to give test

report/certification of fire glass and the glass

should have the stamp showing the value of

E, EW & EI. The glass shall be tested in

approved NABL accredited lab or by any

other accreditation body which operates in

accordance with ISO/IEC 17011 and

accredits labs as per ISO/IEC 17025 for

testing and calibration scopes shall be

eligible. The maximum glazing size shall not

Note: Rate of hardware items deemed to be

include in above items. All Hardware

required as per approved shop drawing

should pass European certificate "CE" of

conformity / UL with required fire ratings.

Providing and fixing bright /matt finished

Stainless Steel handles of approved quality &

make with necessary screws etc all

complete. (a) 125 mm.

Providing & fixing Stainless steel (grade SS-

304 or higher) sliding door bolt/aldrop of

size 250x16mm on door shutter including all

accessories as per direction of E/I

Providing and fixing Stainless steel (grade

SS-304 or higher) tower bolt (barrel type)

with necessary screws etc. complete all work

as per direction of E/I

Filling the gap in between aluminium frame

& adjacent RCC/ Brick/ Stone work by

providing weather silicon sealant over

42 21.8.1 backer rod of approved quality as per 351.40 RM 96.75 33997.95

architectural drawings and direction of

Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Steel work in built up tubular (round, square

or rectangular hollow tubes

etc.) trusses etc., including cutting, hoisting,

fixing in position and

43 10.16.1 applying a priming coat of approved steel 3500.00 KG 194.40 680400.00

primer, including welding and

bolted with special shaped washers etc.

Hot finished welded type tubes

Designing, Providing, installing and fixing

factory finished customed

design pregalvanized high tensile steel joists

manufactured from G350 Z275 confirming to

IS:277-1992, minimum coating of

galvanizing 275 gm/sqm, minimum yield

stress 35 MPa & minimum tensile strength of

380 MPa placed 1.23 metre apart to support

the load of slab etc as per the design &

directions of Engineer-in-Charge.

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Steel work welded in built up sections/

framed work, including cutting, hoisting,

fixing in position and applying a priming coat

45 10.25.2 of approved steel primer using structural 980.00 KG 172.60 169148.00

steel etc. as required. In gratings, frames,

guard bar, ladder, railings, brackets,

gates and similar works

Providing and fixing stainless steel ( Grade

304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding,

buffing, polishing and making curvature

(wherever required) and fitting the same

with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with

necessary accessories & stainless steel dash

fasteners , stainless steel bolts etc., of

required size, on the top of the floor or the

side of waist slab with suitable arrangement

as per approval of Engineer-in-charge.

Structural steel work riveted, bolted or

welded in built up sections, trusses and

47 10.2 framed work, including cutting, hoisting, KG 133.70

fixing in position and applying a priming coat

of approved steel primer all complete.

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses

etc., including cutting, hoisting, fixing in

48 10.16 position and applying a priming coat of

approved steel primer, including welding and

bolted with special shaped washers etc.

10.16.2 Hot finished seamless type tubes KG 206.35

Designing, providing, installing and fixing

factory finished custom

designed cold form Light Gauge Steel

Framed super structure

comprising of steel wall panel, trusses,

purlins etc manufactured out of minimum

0.75 mm thick steel sheet as per design

requirements. The steel sheet shall be

galvanized (AZ-150gms Aluminium Zinc

Alloy coated steel having minimum yield

strength 300-550 Mpa) conforming to AISI

specifications and IBC 2009 for cold formed

steel framing and construction and also as

per IS: 875-1987, ISO 800-1984 and IS:01-

1975. The wind load shall be as per

provisions of IS 875 (part -III).

LGSFS frame shall be designed as per IS:

801 using commercially

available software such as Frame CAD Pro-

11.7/ STAAD PRO-V8i/

ArchitekV2.5.16/ Revit architecture-2011 or

equivalent. Proper usage

of Connection Accessories like Heavy Duty

Tension Ties, Light Duty

Hold-ons, Twist Straps (to connect truss with

wall frames), Strong Tie,

Tie Rod, H-Brackets, Boxing Sections, L-

Shaped Angles for better

Chequerred precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed

with neat cement slurry mixed with pigment

to match the shade of tiles, including

50 11.20.2 rubbing and cleaning etc. complete, on 20 96.05 SQM 1328.35 127588.02

mm thick bed of cement mortar 1:4 (1

cement: 4 coarse sand). Medium shade

pigment using 50% white cement 50%

Marble stone flooring with 18 mm thick

marble stone, as per sample

of marble approved by Engineer-in-charge,

over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with grey cement slurry,

including rubbing and polishing complete

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

52 mm thick cement concrete flooring with

concrete hardener topping, under layer 40

mm thick cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate 20

mm nominal size) and top layer 12 mm thick

cement hardener consisting of mix 1:2 (1

52 11.4 cement hardener mix : 2 graded stone 731.25 SQM 978.45 715491.56

aggregate 6 mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50

kg of cement or as per manufacturer's

specifications. This includes cost of cement

slurry, but excluding the cost of nosing of

steps etc. complete.

Cement plaster skirting up to 30 cm height,

with cement mortar 1:3

(1 cement : 3 coarse sand), finished with a

floating coat of neat cement.

Providing and laying rectified Glazed

Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by

the manufacturer), of 1st quality conforming

to IS : 15622, of approved make, in all

colours, shades, except White, Ivory, Grey,

Fume Red Brown, laid on 20 mm thick

Cement Mortar 1:4 (1 Cement : 4 Coarse

sand), jointing with grey cement slurry @

3.3 kg/ sqm including pointing the joints

with white cement and matching pigments

etc., complete.

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by

the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of

approved make, in all colours and shades,

55 11.41.2 laid on 20mm thick cement mortar 1:4 (1 97.22 SQM 1553.45 151026.41

cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3kg/sqm including

grouting the joints with white cement and

matching pigments etc., complete. (a) Size

of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in

different sizes

(thickness to be specified by the

manufacturer) with water

absorption less than 0.08% and conforming

approved brand & manufacturer, in all

colours and shade, laid

on 20 mm thick cement mortar 1:4 (1

cement: 4 coarse sand)

jointing with grey cement slurry @3.3

kg/sqm including grouting

the joints with white cement and matching

pigments etc. The

tiles must be cut with the zero chipping

diamond cutter only .

Laying of tiles will be done with the notch

trowel, plier, wedge,

clips of required thickness, leveling system

and rubber mallet for

Double charge vitrified tile polished finish of

Providing and laying Vitrified tiles in

different sizes (thickness to be specified by

manufacturer), with water absorption less

than 0.08 % and onforming to I.S. 15622,

of approved make, in all colours & shade, in

skirting, riser of steps, over 12 mm thick

bed of cement mortar 1:3 (1 cement: 3

coarse sand), jointing with grey cement

slurry @ 3.3kg/sqm including grouting the

joint with white cement & matching

pigments etc. complete. Size of Tile 600x600

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and laying flamed finish Granite

stone flooring in required design and

patterns, in linear as well as curvilinear

portions of the building all complete as per

the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base

of cement mortar 1:4 (1 cement : 4coarse

sand) laid and jointed with cement slurry

and pointing with white cement slurry

admixed with pigment of matching shade

including rubbing, curing and polishing etc.

all complete as specified and as

directed by the Engineer-in-Charge :Flamed

finish granite stone slab Jet Black, Cherry

Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone

flooring in required design and patterns, in

linear as well as curvilinear portions of the

building all complete as per the architectural

drawings with 18 mm thick stone slab over

20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid

59 11.56.1 and jointed with cement slurry and pointing 65.07 SQM 4481.30 291598.19

with white cement slurry admixed with

pigment of matching shade including

rubbing, curing and polishing etc. all

complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black,

Cherry/Ruby Red or equivalent

Providing and laying C.C. pavement of mix M-

25 with ready mixed concrete from batching

plant. The ready mixed concrete shall be laid

and finished with screed board vibrator ,

vacuum dewatering process and finally

finished by floating, brooming with wire

brush etc. complete as per specifications and

directions of Engineer-incharge.

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this

item is @ 330 kg/cum.

Excess/less cement used as per design mix

is payable/ recoverable separately).

Providing and fixing false ceiling at all height

including providing and

fixing of frame work made of special

sections, power pressed from

M.S. sheets and galvanized with zinc coating

of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting

of angle cleats of size

25 mm wide x 1.6 mm thick with flanges of

27 mm and 37mm, at

1200 mm centre to centre, one flange fixed

to the ceiling with dash

fastener 12.5 mm dia x 50mm long with

61 6mm dia bolts, other flange

of cleat fixed to the angle hangers of

25x10x0.50 mm of required

length with nuts & bolts of required size and

other end of angle

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running

at the spacing of 1200 mm centre to centre,

to which the ceiling

section 0.5 mm thick bottom wedge of 80

mm with tapered flanges

of 26 mm each having lips of 10.5 mm, at

450 mm centre to centre,

shall be fixed in a direction perpendicular to

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

with connecting clips made out of 2.64 mm

dia x 230 mm long G.I.

wire at every junction, including fixing

perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm

and 30 mm long, the

perimeter of ceiling fixed to wall/partition

with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall

screws @ 230 mm

interval, including fixing of gypsum board to

ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and

finishing to a flush finish

of tapered and square edges of the board

with recommended

compound , jointingjointing

tapes , finishing with

jointing compound in 3

layers covering upto 150 mm on both sides

of joint and two coats of

primer suitable for board, all as per

manufacturer's specification and

also including the cost of making openings

for light fittings, grills,

diffusers, cutouts made with frame of

perimeter channels suitably

fixed, all complete as per drawings,

specification and direction of

the Engineer in Charge but excluding the

cost of painting with :

12.5 mm thick tapered edge gypsum plain

conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing and fixing tiled false ceiling of

specified materials of size

595x595 mm in true horizontal level,

suspended on inter locking

metal grid of hot dipped galvanized steel

sections ( galvanized @

120 grams/ sqm, both side inclusive)

consisting of main "T" runner

with suitably spaced joints to get required

length and of size 24x38

mm made from 0.30 mm thick (minimum)

sheet, spaced at 1200

mm center to center and cross "T" of size

24x25 mm made of 0.30

mm thick (minimum) sheet, 1200 mm long

spaced between main

"T" at 600 mm center to center to form a

grid of 1200x600 mm and

secondary cross "T" of length 600 mm and

size 24x25 mm made of

0.30 mm thick (minimum) sheet to be

interlocked at middle of the

1200x600 mm panel to form grids of

600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling

tiles of approved texture

in the grid including, required

cutting/making,

GI Metal Ceiling opening for services

Lay in plain Tegular edge

Global white color tiles of size 595x595 mm,

and 0.5 mm thick with 8 mm drop; made of

G I sheet having galvanizing of 100

12.52.1 gms/sqm (both sides inclusive) and electro 65.58 SQM 1902.95 124795.46

statically polyester powder coated of

thickness 60 microns

(minimum), including factory painted after

12mm cement plaster in single coat on fair

side of single or half brick wall for exterior

plastering up to floor two level including

internal rounded angles chamfers, and/or

rounded angles not exceeding 80mm in

girth and finished even and smooth no extra

for mixing any additive. 1:6 (1 cement: 6

15 mm cement plaster on the rough side of

64 13.5.2 single or half brick wall of mix : 1:6 (1 2367.85 SQM 395.35 936129.50

cement: 6 coarse sand)

6 mm cement plaster on celling (a) 1:3(1

cement:3 fine sand)

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Finishing walls with textured exterior paint

of required shade: New work (Two or more

66 13.45.1 coats applied @ 3.28 ltr/10 sqm) over and 1289.66 SQM 223.60 288367.98

including priming coat of exterior primer

applied @ 2.20kg/10 sqm

Finishing walls with 100% Premium acrylic

emulsion paint having VOC less than 50

gm/litre and UV resistance as per IS

67 13.48A 15489:2004, Alkali & fungal resistance, dirt

resistance exterior paint of required shade

(Company Depot Tinted) with silicon

New work (Two or more coats applied @

1.43 litre/ 10 sqm. Over and including

priming coat of exterior primer applied @

0.90 litre/10 sqm.

13.50 Applying priming coat:

With ready mixed red oxide zink chromate

68 13.50.3 primer of approved brand and manufacture 905.99 SQM 67.40 61063.73

on steel galvanised iron/steel works.

Painting with synthetic enamel paint of

70 13.61 approved brand and manufacture to give

13.61.1 Two or more coats on new work. 905.99 SQM 155.90 141243.84

Providing and applying white cement based

putty of average thickness 1 mm, of

71 13.80 approved brand and manufacturer, over the 4463.33 SQM 156.05 696502.65

plastered wall surface to prepare the surface

even and smooth complete.

L ALUMINIUM WORK

Providing and fixing aluminium work for

doors, windows, ventilators

and partitions with extruded built up

standard tubular sections/

appropriate Z sections and other sections of

conforming to IS: 733 and IS: 1285, fixing

with dash fasteners of

required dia and size, including necessary

filling up the gaps at

junctions, i.e. at top, bottom and sides with

required EPDM rubber/

neoprene gasket etc. Aluminium sections

shall be smooth, rust free,

straight, mitred and jointed mechanically

wherever required including

cleat angle, Aluminium snap beading for

glazing / paneling, C.P.

brass / stainless steel screws, all complete

as per architectural

drawings and the directions of Engineer-in-

charge. (Glazing, paneling

and dash fasteners to be paid for separately)

21.1.1 For fixed portion

Anodised aluminium (anodised transparent

or dyed to required shade according to IS:

1868, Minimum anodic coating of grade

For shutters of doors, windows & ventilators

providing and fixing hinges/ pivots and

making provision

21.1.2 for fixing of fittings wherever required

including the cost

of EPDM rubber / neoprene gasket required

shall be paid for separately)

Anodised aluminium (anodised transparent

or dyed to required shade according to IS:

1868, Minimum anodic coating of grade

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing and fixing glazing in aluminium

door, window, ventilator

shutters and partitions etc. with EPDM

rubber / neoprene gasket

73 21.3 etc. complete as per the architectural

drawings and the directions of

engineer-in-charge . (Cost of aluminium

snap beading shall be paid

in basic item):

With float glass panes of 8 mm thickness

less than 20 kg/sqm)

M Water Proofing

Providing and laying in situ seven course

water proofing treatment

with APP (Atactic poly-propylene) modified

Polymeric memberane

over roof consisting of first coat of bitumen

primer @ 0.40 litre per

sqm, 2nd, 4th & 6th courses of bonding

material @ 1.20 Kg/sqm,

which shall consist of blown type bitumen of

grade 85/25 conforming

to IS : 702, 3rd and 5th layers of roofing

membrane APP modified

Polymeric membrane 1.5 mm thick of 2.25

Kg/sqm weight consisting

of five layers prefabricated with centre core

as 20 micron HMHDPE

film sandwiched on both sides with

polymeric mix and the polymeric

mix is protected on both side with 20 micron

HMHDPE film. 7th, the

top most layer shall be finished with brick

tiles of class designation

10 grouted with cement mortar 1:3

(1cement : 3 fine sand) mixed

with 2% integral water proofing compound

by weight of cement over

a 12 mm layer of cement mortar 1:3 (1

cement : 3 fine sand) and

Providing and laying brick tiles over mumty

roofs, grouted with cement

mortar 1:3 (1 cement : 3 fine sand) mixed

with 2% of integral water

proofing compound by weight of cement,

over 12 mm layer of cement

mortar 1:3 (1 cement : 3 fine sand) and

With common burnt clay F.P.S. (non

12.19.1 modular) brick tiles 358.67 SQM 607.40 217856.16

of class designation 10

N Roof Sheeting

PROFLEX Roof System wuth 1.3 mm thick

color coated galvanised sheet

O Loft and Wardrobes

All works above plinth level upto floor V level

Suspended floors, roofs, landings, balconies

and access platform.

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

79 5.22.A.6 placing in position and binding all complete 63.00 Kg 107.85 6794.55

above plinth level. Thermo-Mechanically

Treated bars of grade Fe-500 D or more.

12mm cement plaster in single coat on fair

side of single or half brick wall for exterior

plastering up to floor two level including

internal rounded angles chamfers, and/or

rounded angles not exceeding 80mm in

girth and finished even and smooth no extra

for mixing any additive. 1:6 (1 cement: 6

6 mm cement plaster on celling (a) 1:3 (1

cement:3 fine sand)

Wall painting with acrylic emulsion paint of

82 13.60 approved brand and manufacture to give an

83 13.60.1 Two or more coats on new work. 17.85 Sqm

Providing and applying white cement based

putty of average thickness 1 mm, of

84 13.80 approved brand and manufacturer, over the 17.85 Sqm 156.05 2785.49

plastered wall surface to prepare the surface

even and smooth complete.

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Providing wood work in frames of false

ceiling, partitions etc. sawn and fixed in

position with necessary stainless steel

Kiln seasoned and chemically treated hollock

Providing and fixing cup board shutters 25

mm thick, with Pre-laminated flat pressed

three layer particle board or graded wood

particle board IS: 12823 marked, exterior

grade (Grade l Type ll), having one side

decorative lamination and other side

balancing lamination, including IInd class

teak wood lipping of 25 mm wide x12 mm

thick with necessary screws and bright

finished stainless steel piano hinges,

complete as per direction of the Engineer-in-

Providing and fixing Pre-laminated medium

density fibre board IS: 14587:1998 marked,

with one side decorative lamination other

side balancing lamination Grade-I (exterior

9.157 grade) in shelves with screws and fittings

wherever required, edges to be sealed with

PVC edge bending tape 2.00 mm thick of

approved brand (fittings to be paid

Pre-laminated with decorative lamination

one side and other side balancing lamination

exterior Grade - I MDF Board 18 mm thick

confirming to IS:14587

Providing and fixing magnetic catcher of

approved quality in cupboard / ward robe

shutters, including fixing with necessary

screws etc. complete.

9.114.2 Double strip (horizontal type) 26.00 Each 39.70 1032.20

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required size,

approved shade, colour and texture laid over

8.2 20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching

pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete

89 8.2.2 Granite of any colour and shade

8.2.2.2 Area of slab over 0.50 sqm 9.59 Sqm 5136.30 49277.66

Providing & Fixing decorative high pressure

laminated sheet of plain / wood grain in

gloss / matt/ suede finish with high density

90 9.127.1 protective surface layer and reverse side of 27.96 Sqm 1045.95 29240.58

adhesive bonding quality conforming to IS :

2046 Type S, including cost of adhesive of

approved quality 1 mm thick

Providing and fixing wooden moulded

beading to door and window frames with

iron screws, plugs and priming coat on

unexposed surface etc. complete :

Kiln seasoned and chemically treated hollock

Providing and fixing special quality

chromium plated brass cupboard locks with

six levers of approved quality including

necessary screws etc. complete. Size 50mm

Providing and fixing chromium plated brass

93 9.92.2 handles with necessary screws etc. 26.00 Each 206.25 5362.50

complete: 100mm

Badminton court line marking by acrylic

paint of approved make and as per direction

of Engineer-Incharge (tentative area of hall

625 Sqm for 2 badmintan court)

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

DSR -17.2.1 Providing and Fixing white viterous china

pedestal type water closet ( European type

WC Pan ) with seat and lid , 10 litre low level

White pvc flushing cistern , including flush

pipe with manually controlled device (

1 handle lever ) , Conforming to IS : 7231 with 10.00 Each 6515.55 65155.50

all fittings and fixtures complete including

cutting and making good the walls and floors

wherever required . WC Pan with ISI marked

white solid plastic seat and lid .

DSR -17.7 Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

2 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls wherever

White Vitreous China Wash basin size

630x450 mm with a pair of 15 mm C.P. 9.00 Each 2648.85 23839.65

17.7.1 brass pillar tap

DSR -17.31 Providing and fixing 600x450 mm beveled

edge mirror of superior glass ( of approved

3 quality ) complete with 6 mm thick hard 9.00 Each 1607.95 14471.55

board ground fixed to wooden cleats with

C.P brass screws and washers complete .

17.5 Providing and fixing white vitreous china flat

back half stall urinal of size 580x380x350

mm with white PVC automatic flushing

cistern, with fittings, standard size C.P.

brass flush pipe, spreaders with unions and

clamps (all in C.P. brass) with waste fitting

as per IS : 2556, C.I. trap with outlet

grating and other couplings in C.P. brass,

including painting of fittings and cutting and

making good the walls and floors wherever

17.5.3 Range of three half stall urinals with 10 litre

P.V.C. automatic flushing cistern

DSR -8.10 Providing and fixing stone slab with table

rubbed, edges rounded and polished, of size

75x50 cm deep and 1.8 cm thick, fixed in

urinal partitions by cutting a chase of

appropriate width with chase cutter and

4 embedding the stone in the chase with

epoxy grout or with cement concrete 1:2:4

(1 cement : 2 coarse sand : 4 graded stone

aggregate 6 mm nominal size) as per

direction of Engineer-in-charge and finished

4.1 8.10.2 Granite Stone of approved shade 3.00 Sqm 4051.85 12155.55

DSR -18.49 Providing & fixing C.P. brass bib cock of

5 approved quality conforming to IS :8931.

17.22A Providing and fixing CP Brass 32mm size

bottle trap of approved quality & make and 1034.80 8278.40

as per the direction of engineer in charge.

DSR -18.53 Providing and fixing C.P. brass angle valve

6 for basin mixer and geyser points of

approved quality conforming to IS:8931

DSR -18.21 Providing and fixing unplasticised P.V.C.

7 connection pipe with PTMT Nuts, collar and

bush of approved quality and colour.

7.1 18.21.2.1 15 mm nominal bore with 45cm length 30.00 Each 97.75 2932.50

DSR -18.53A Providing and fixing CP Brass extension

8 nipple ( size 15mm x 50 mm ) of approved 30.00 74.80 2244.00

make and quality as per direction of

engineer - in - charge .

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

DSR -17.28 Providing & fixing of Waste pipe for Wash

9 basins & Sinks including pvc waste fittings

DSR -18.48 Providing and placing on terrace (at all floor

levels) polyethylene water storage tank, ISI

: 12701 marked, with cover and suitable

10 locking arrangement and making necessary 10000.00 Per Litre 11.00 110000.00

holes for inlet, outlet and overflow pipes but

without fittings and the base support for

DSR -18.58 Providing and fixing PTMT grating of

approved quality and colour

Providing and fixing 8mm dia C.P./S.S. Jet

with flexible tube upto 1meter long with S.S.

Triangular plate to european type W.C. Of 10.00 Each 349.15 3491.50

approved quality and make as approved by

engineer in charge.

NS-3 Providing and fixing vertical or horizontal

storage type hot water heater electrical

operated fixed to wall with anchor bolts &

nuts, 15mm CP brass angle stop cock and

1.00 15mm CP brass non-return valve complete

including making connections with 15mm dia

CP connecting pipes on inlet and outlet,

suitable length of power cable and 15 amps

13.1 a) 15 Litre Capacity 6.00 Each 12081.00 72486.00

17.22B Providing and fixing CP Brass Single lever

telephonic wall mixer of

quality & make as approved by Engineer in 6.00 Each 6940.75 41644.50

(a) 15 mm nominal dia

17.34 Providing and fixing toilet paper holder :

17.71 Providing and fixing PTMT liquid soap

container 109 mm wide, 125 mm high and

112 mm distance from wall of standard

shape with bracket of the same materials 6.00 Each 168.35 1010.10

with snap fittings of approved quality and

colour, weighing not less than 105 gms.

17.73 Providing and fixing PTMT towel rail

complete with brackets fixed to wooden

cleats with CP brass screws with concealed

fittings arrangement of approved quality and

17.73.1 450 mm long towel rail with total length of

495 mm, 78 mm wide and effective height of 673.40 4040.40

88 mm, weighing not less than 170 gms

18.22 Providing and fixing C.P. brass shower rose

with 15 or 20 mm inlet

18.52 Providing and fixing CP brass stop cock

(concealed) of standard design and approved

make confirming to IS: 8931.

18.52.1 15mm nominal bore 12.00 Each 670.45 8045.40

NS Providing & Fixing of Grab bar size 600X600

mm pipe O.D 32 mm , thiickness 2 mm of

non slipping grip as per standard

specification of use in disabled toilet 1.00 Each 15642.00 15642.00

complete with brackets suitable for wall

installation as per approved sample

complete in all respect.

SUB HEAD-II- SOIL , WASTE VENT AND RAIN

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

DSR -12.22 Making khurras 45x45 cm with average

minimum thickness of 5 cm cement concrete

1:2:4 (1 cement:2 coarse sand:4 graded

stone aggregate of 20 mm nominal size)

1 over P.V.C. sheet 1 mx1 mx400 micron, 4.00 Each 298.25 1193.00

finished 12 mm cement plaster 1:3 (1

cement:3 coarse sand) and a coat of neat

cement rounding the edges and making and

finishing the outlet complete

DSR -12.41 Providing and Fixing on wall unplasticised

Rigid PVC Rain water pipes conforming to IS

2 : 13592 Type A , including jointing with seal

ring conforming to IS : 5382 , leaving 10

mm gap for thermal expansion

12.41.2 Single Socketed pipes 110 mm diameter

DSR -12.44 Providing and Fixing to the inlet mouth of

3 rain water pipe cast iron grating 15 cm 8.00 54.70 437.60

diameter and weighing not less than 440

DSR -12.37 Providing and Fixing 100 mm diameter and

4 60 cm long rain water spout in cement

mortar 1:4 ( 1 Cement : 4 Fine Sand )

4.1 12.37.1 Stone Ware Spout 2.00 Each 164.20 328.40

DSR -12.42 Providing and Fixing on wall face Rigid

Unplasticised UPVC moulded fittings /

accessories for unplasticised Rigid PVC Rain

5 water pipes conforming to IS : 13592 Type A

including jointing with seal ring conforming

to IS : 5382 leaving 10 mm gap for thermal

12.42.1 Coupler

12.42.2 Single Push Fit Coupler

12.42.3 Single Tee with door

12.42.4 Single Tee without door

12.42.5 Bend 87.5 degree

12.42.6 Shoe ( Plain )

DSR -12.43 Providing and Fixing unplasticised PVC pipe

clips of approved design to unplasticised -

PVC rain water pipes by means of 50x50x50

mm hard wood plugs , screwed with MS

6 screws of required length , including cutting

brick work with fixing in cement mortar 1:4 (

1 Cement : 4 Coarse Sand ) and making

good the wall etc . complete

NS-4 Providing and fixing uPVC 6 Kg/cm2 Soil ,

Waste & RWP pipes (IS: 13592 Class B)

including all fittings (plain or door) e.g.

bends, junction, cowls, offsets, access

7 pieces, jointing with rubber ring/solvent

cement joints including cutting chase or

holes in walls and floors and making good

wherever required.

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

NS-5 Providing & fixing in position upvc P"or S"

trap of self cleaning design of following

sizes for the embedded areas Making

proper connection with chemical sealent

joint , cutting chase / hole in floors /slabs

8 and bringing the same in proper condition in

cement concrete 1:2:4 mix complete as

required. including cost of cutting and

making good the walls and floors where

8.1 a) 110 mm inlet and 110 mm outlet 10.00 Each 734.00 7340.00

NS-6 Providing & fixing in position upvc floor drain

9 including cost of cutting and making good

the walls and floors wherever required.

9.1 a) 110 mm inlet and outlet 18.00 Each 451.00 8118.00

NS-7 Providing and fixing uPVC waste pipes for

WB , SINK , URINAL , FD (IS: 4985 ) 6 Kg /

Sqcm including all fittings (plain or door)

e.g. bends, junction, cowls, offsets, access

10 pieces, jointing with rubber ring/solvent

cement joints including cutting chase or

holes in walls and floors and making good

wherever required.

NS-13 Providing and fixing Cast bronze chrome

plated grating with ring and Stainless steel

11 anti cockroach basket and two SS screw

including fixing to the floor with cement

MR Providing and fixing UPVC inlet fitting with

maximum 3 inlets 32,40 or 50 mm size

fabricated from 110 mm dia UPVC pipes and

12 fixed to upvc sockets,fixed to upvc trap 7.00 Each 4682.00 32774.00

with chemical sealent joint and set in

cement concrete as per standard drawing

NS-8 Providing and fixing upvc cleanout plug(

Ceiling or Floor) with suitable insert keys for

13 opening, male threaded joint with upvc

socket fixed to uPVC pipe complete in all

13.1 a) 110 mm diameter Pipe 4.00 Each 538.00 2152.00

SUB HEAD- III - INTERNAL WATER SUPPLY

DSR -18.8 Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings, including fixing the pipe with clamps

1 at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

Concealed work, including cutting chases

and making good the walls etc.

1.1 18.8.1 15 mm nominal outer dia Pipes 35.00 Metre 497.80 17423.00

1.2 18.8.2 20 mm nominal outer dia Pipes 40.00 Metre 537.60 21504.00

1.3 18.8.3 25 mm nominal outer dia Pipes 40.00 Metre 627.25 25090.00

1.4 18.8.4 32 mm nominal outer dia Pipes 40.00 Metre 739.30 29572.00

DSR -18.7 Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings, including fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per

direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25mm nominal bore 40.00 Metre 401.55 16062.00

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

18.7.4 32 mm nominal bore 40.00 Metre 518.75 20750.00

18.7.5 40mm nominal bore 50.00 Metre 702.95 35147.50

18.7.6 50mm nominal bore 120.00 Metre 934.15 112098.00

NS-9 Providing and fixing Thermoflex or Careflex

thermal insulation tubing, a elastomeric

flexible material having hermetic blister

2 closed cell structure of expanded synthetic

rubber over pipes of following nominal bores

and thickness including all required

accessories complete as per specification.

9 mm thick ( Pipes in Chases)

2.1 a) For 15 mm dia Pipe 10.00 Metre 92.00 920.00

2.2 b) For 20 mm dia Pipe 50.00 Metre 101.00 5050.00

c) For 32 mm dia Pipe 20.00 Metre 120.00 2400.00

NS-10 Providing and Fixing full way lever operated

forged brass ball valve of brass body with

forged brass hard chromeplated steel ball

3 tasted to a pressure not less than 15

kg/sqcm with threaded / flanged joints

complete with nuts, bolts, gaskets, washers

3.1 a) 15 mm dia nominal bore 2.00 Each 250.00 500.00

3.2 b) 20 mm dia nominal bore 5.00 Each 340.00 1700.00

3.3 c) 25 mm dia nominal bore 5.00 Each 512.00 2560.00

3.4 d) 32 mm dia nominal bore 4.00 Each 774.00 3096.00

3.5 e) 40 mm dia nominal bore 3.00 Each 1195.00 3585.00

NS-11 Providing, fixing, testing and commissioning

of motorised butterfly valve of following dia

for filling of overhead water tank complete

with high and low level control switches to

control tanks. The level controllers shall be

installed in overhead tanks. The level switch

will close the valve when water level is high

4 in overhead tank and open the valve when

overhead water tank level is low. The system

should be complete in all respects with

accessories 220 V AC / 24 V DC, IP67

electrical water level control unit, copper

control wiring in whether proof casing etc.

4.1 a) 40 mm dia nominal bore 1.00 Each 11393.00 11393.00

ELECTRICAL WORKS

SUBHEAD - I - CIRCUIT CUM POINT WIRING

Wiring for light point/ fan point/ exhaust fan

point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core

cable in surface / recessed medium class

1 DSR 1.10 PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point

with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

Wiring for group controlled (looped) light

point/fan point/exhaust fan point/ call bell

point ( without Independent switch etc.) with

1.5 sq. mm FRLS PVC insulated copper

2 DSR-1.55 conductor single core cable in surface/

recessed PVC conduit, and earthing the point

with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc as required.

(Switch Control Secondary Points)

Wiring for light point/ fan point/ exhaust fan

point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core

cable in surface / recessed steel conduit,

3 DSR-1.3 with modular switch, modular plate, suitable

GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required. (Switch

Control Primary Points)

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Wiring for group controlled (looped) light

point/fan point/exhaust fan point/ call bell

point (without Independent switch etc.) with

1.5 sq. mm FRLS PVC insulated copper

4 DSR-1.54 conductor single core cable in surface/

recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc as

required. (Switch Control Secondary

MCB CONTROL LIGHT POINTS

Wiring for light point/ fan point/ exhaust fan

point/ call bell point with 2.5 sq.mm FRLS

PVC insulated copper conductor single core

cable in surface / recessed steel conduit,

5 NSI-1 with modular switch, modular plate, suitable

GI box and earthing the point with 2.5

sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required. (Switch

Control Primary Points)

5.1 NSI-1.1 Primary point controlled by one MCB. 12.00 Point 1535.50 18426.00

Same as item above but Secondary point.

5.2 NSI-1.2 i.e. Points to be looped with Primary point 12.00 Point 1365.90 16390.80

with 2.5 sqmm wire and Point wiring

Wiring for light/ power plug with 2X4 sq.

mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed steel

6 DSR 1.5 conduit alongwith 1 No. 4 sq. mm FRLS PVC 350.00 Metre 433.00 151550.00

insulated copper conductor single core cable

for loop earthing as required.

Wiring for circuit/ submain wiring alongwith

earth wire with the following sizes of FRLS

7 DSR 1.7 PVC insulated copper conductor, single core

cable in surface/ recessed steel conduit as

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 x 10 sq. mm + 1 x 6 sq.mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box

with modular plate and

cover in front on surface or in recess,

8 DSR 1.31 including providing and 16.00 Each 477.00 7632.00

fixing 3 pin 5/6 A modular socket outlet and

switch, connections etc. as required.

Supply and Wiring for 250 volts single

phase and neutral 2 Nos 6 amps socket

outlate with control by 1 No switched with

2.5 sq.mm PVC insulated copper conductor

1100 volts grade stranded flexible FRLS

wires in concealed or surface mounted 25

mm dia 2mm thick PVC conduit including

providing and fixing of 6 amps 3 pin switch

socket outlet of aprpoved make and design

in 2 mm thick GI box with grid plate and

earthing of third pin of the socket with 2.5

Sq. mm PVC insulated copper conductor

stranded flexible FRLS wire.(maximum

four no. of switches socket shall be

connected on one circuit)

Supplying and fixing suitable size GI box

with modular plate and

cover in front on surface or in recess,

10 DSR 1.32 including providing and 15.00 Each 586.00 8790.00

fixing 6 pin 5/6 & 15/16 A modular socket

outlet and 15/16 A

modular switch, connections etc. as

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Supplying and fixing 3 pin, 5 A ceiling rose

on the existing junction box/ wooden block

including connections etc. as required.

Supplying & fixing suitable size GI box wih

modular plate and cover in front on surface

or in recess i/c providing and fixing 25 amp

12 DSR-1.57 modular socket outlet and 25 Amps modular 2.00 Each 727.00 1454.00

SP MCB, “C” curve including connection,

painting etc. as required. (AC's & Gysers)

Supplying and fixing following modular

switch/ socket on the

13 DSR 1.24 existing modular plate & switch box

including connections but

excluding modular plate etc. as required.

13.1 DSR 1.24.6 Telephone socket outlet 4.00 Nos 148.00 592.00

Supplying and fixing following size/

modules, GI box alongwith

14 DSR 1.27 modular base & cover plate for modular

switches in recess etc.

Supplying and fixing following size/

modules, GI box alongwith

15 DSR 1.24 modular base & cover plate for modular

switches in recess etc.

15.1 DSR 1.24.4 3 pin , 5/6 amps socket outlet 2.00 Each 122.00 244.00

Supplying and fixing following size/

modules, GI box alongwith

16 DSR 1.27 modular base & cover plate for modular

switches in recess etc.

Supplying and fixing of following sizes of

medium class PVC

conduit along with accessories in

17 DSR 1.21 surface/recess including

cutting the wall and making good the same

in case of recessed

conduit as required.

Supplying and drawing following pair 0.5

mm dia FRLS PVC insulated annealed copper

18.1 1.18 conductor, unarmored telephone cable in the

existing surface/ recessed steel/ PVC conduit

SUBHEAD - II - FITTINGS & FIXTURES

Supply, Installation, Testing and

Commissioning of 9 W Bulk head Light.

Supply, Installation, Testing and

Commissioning of 5W Mirror Light.

Supply, Installation, Testing and

3 Commissioning of 18W Recessed/Surface 86.00 Each 1975.94 169930.84

Mounted LED circular Downlighter.

Supply, Installation, Testing and

4 NSI-4 Commissioning of 20W Wall/Surface mouted 15.00 Each 1975.94 29639.10

Supply, Installation, Testing and

5 NSI-5 Commissioning of 65W Surface mounted 10.00 Each 6107.46 61074.60

Supply, Installation, Testing and

Commissioning of 12W Recessed mounted

6 NSI-6 LED circular Downlighter (Cat no-Bajaj 40.00 Each 1167.60 46704.00

Lighting BGSLO SLEEK SURFACE 12W WH RD

or equivalent as specified in the approved

Supply, Installation, Testing and

7 Commissioning of 150W highway with 5.00 Each 7469.82 37349.10

150LPW Ceiling mounted LED Light

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Supply, Installation, Testing and

8 Commissioning of 250W Highway with 15.00 Each 11204.73 168070.95

130LPW ceiling mounted LED Light Fixtures

Supply, Installation, Testing and

Commissioning of 1200 mm sweep,

BEE 5 star rated, ceiling fan with Brush Less

Direct Current (BLDC)

Motor, class of insulation: B, 3 nos. blades,

30 cm long down rod, 2

nos. canopies, shackle kit, safety rope,

copper winding, Power Factor not less than

0.9, Service Value (CM/M/W) minimum 6.00,

Air delivery minimum 210 Cum/Min , 350

RPM (tolerance as per IS : 374-2019), THD

less than 10%, remote or electronic

regulator unit for speed control and all

remaining accessories including safety pin,

nut bolts, washers, temperature rise=75

degree C (max.), insulation resistance more

than 2 mega ohm, suitable for 230 V, 50 Hz,

single phase AC Supply, earthing etc.

complete as required.

Supplying and fixing two module stepped

type electronic fan

10 DSR 1.25 regulator on the existing modular plate 8.00 Each 369.00 2952.00

switch box including

connections but excluding modular plate etc.

Installation, testing and commissioning of

ceiling fan, including

wiring the down rods of standard length

sq. mm FRLS PVC insulated, copper

conductor, single core cable

etc. as required.

Supply of 300 mm dia Domestic Exhaust Fan

13 NSI-10 Supply of heavy duty 450mm Wall Fan 3.00 each 6848.44 20545.32

SUBHEAD - III - MAIN BOARDS

Supplying, installing, testing &

commissioning of following type

compartmentalised wall mounted / floor

mounted cubicle board made from 2mm

thick CRCA sheet dust & vermin proof duly

1 phosphatized & powder coated inclusive of

suitable size 4 strip Al. Busbar complete with

interconnection providing Lugs, inter-

earthing, painting etc. i/c providing & fixing

below noted accessories:

Receiving,unloading,storing, handling,

installation, testing and commissioning of

following MV Switchboards complete as

required and as per site condition and

dimension of all panels shall be carried out

as per the attachad sld

1 NSI-1 MAIN LT PANEL ( FOR BUILDING ) 1.00 Set 150800.00 150800.00

2 NSI-2 FIRE FIGHTING PANEL 1.00 Set 40000.00 40000.00

SUBHEAD - IV - DISTRIBUTION BOARDS

Supplying and fixing following way, single

pole and neutral,

sheet steel, MCB distribution board, 240 V,

on surface/ recess,

1 DSR 2.3 complete with tinned copper bus bar, neutral

bar, din bar, interconnections, powder

painted including

earthing etc. as required. (But without

MCB/RCCB/Isolator)

1.2 DSR 2.3.2 8 way, Double door 1.00 Each 2573.00 2573.00

1.3 DSR 2.3.3 12 way, Double door 2.00 Each 2315.00 4630.00

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Supplying and fixing following way, three

pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/

recess complete with tinned copper busbar,

2 DSR 2.4 neutral busbar, earth bar, din bar,

detachable gland plate, interconnections,

phosphatized and powder painted including

earthing etc. as required. (But without MCB/

RCCB/ Isolator)

Supplying and fixing of following ways

surface/ recess mounting, vertical type,

415 V, TPN MCB distribution board of sheet

steel, dust protected, duly powder painted,

inclusive of 200 A tinned copper bus bar,

3 DSR 2.5 common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and

incomer) as required . (Note :Vertical type

MCB TPDB is normally used where 3 phase

outlets are required.)

Supplying and fixing 5 A to 32 A rating,

240/415 V, 10 kA, "C" curve, miniature

4 DSR 2.10 circuit breaker suitable for inductive load of

following poles in the existing MCB DB

complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double

pole, 240 V, isolator in the existing MCB DB

5 DSR 2.12 complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, four

pole, 415 V, isolator in the existing MCB DB

6 DSR 2.13 complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double

pole, (single phase and neutral), 240 V,

residual current circuit breaker (RCCB),

7 DSR 2.14 having a sensitivity current 30 mA in the

existing MCB DB complete with connections,

testing and commissioning etc. asrequired.

Supplying and fixing DP sheet steel

enclosure on surface/ recess

8 DSR-2.16 along with 25/32 A 240 V "C" curve DP MCB 3.00 Each 1169.00 3507.00

connections, testing and commissioning etc.

Supplying and fixing single pole blanking

9 DSR 2.11 plate in the existing 5.00 Each 13.00 65.00

MCB DB complete etc. as required.

FIRE FIGHTING WORKS

A. SUB HEAD - A : PUMPS & EQUIPMENTS

1 18.4 Supplying , Installation , Testing and

Commissioning of Electric Driven Terrace

Pump Suitable for Automatic operation and

Consisting of Following Complete in all

Respect as Required ( Terrace Fire Pump )

1.1 a) Horizontal Type Multistage , Centrifugal

Pump of Cast Iron Body and Bronze Impeller

with Stainless Steel Shaft Mechanical Seal

Conforming to IS : 1520

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

1.2 b) Suitable HP Squirrel cage Induction motor ,

TEFC , synchronous speed 1500 RPM ,

Suitable for operation on 415 Volts 3 Phase

50 Hz AC Supply with IP 68 protection for

enclosure Horizontal Foot Mounted type with

class F insulation Conforming to IS : 325

with Energy Efficiency class IE-3

1.3 c) MS Fabricated Common Base Plate Coupling

, Coupling Guard Foundation bolts etc as

1.4 d) Suitable Cement Concrete Foundation duly

Plastered with anti vibration Pads

The Head of the Pump is Selected in a

manner so as to give a minimum 3.5

kg/sqcm pressure at the highest / farthest

2 18.20 Supplying and Fixing Air Vessel made of 450

mm dia 8 mm thick ms sheet 2000 mm in

height with air release valve on top and

flanged connection to riser drain

arrangement with 25 mm dia gunmetal 2.00 Set 18244.00 36488.00

wheel valve with required accessories

pressure gauge and painting with synthetic

enamel paint of approved shade as required

B. PIPING, HYDRANT , AND ACCESSORIES

1 18.7 Providing Laying Testing and Commissioning

of C class Heavy duty MS Pipe Conforming

to IS : 1239 / 3589 including Fittings like

elbows , tees , flanges , tapers , nuts , bolts

, gaskets etc in ground including welding

excavation and Providing cement concrete

blocks as supports anticorrosive treatment

with coaltar / asphalts tape as per IS :10221

refilling the trench etc of following sizes

complete as required .

2 18.11 Supplying Fixing Testing and Commissioning

of butterfly valve of PN 1.6 Rating with

Bronze Gunmetal Sheet duly ISI marked

complete with nuts , bolts , washers ,

gaskets conforming to IS : 13095 of

following sizes as required .

3 18.14 Providing Installation Testing and

Commissioning of Non Return Valve of

following sizes conforming to IS : 5312

complete with rubber gasket , GI Bolts ,

Nuts , washers etc as required .

4 18.15 Providing Installation Testing and

Commissioning of Stainless Steel Y Strainer

fabricated out of 1.6 mm thick stainless steel

, Grade 304 , Sheet with 3 mm dia holes

with stainless steel flange .

5 18.9 Supplying and Fixing Single Headed Internal

Hydrant Valve with instantaneous gunmetal

material coupling of 63 mm dia with cast

iron wheel ISI marked conforming to IS :

5290 ( Type A ) with blank Gunmetal

material cap and chain as required .

5.1 18.9.1 Single Headed Gunmetal Material 3.00 Set 7646.00 22938.00

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

6 18.13 Supplying and Fixing orifice plate made out

of 6 mm thick stainless steel ( Grade 304 )

with orifice of required size to be fitted

between flange and landing valve of external 4.00 Each 1321.00 5284.00

and internal hydrants to reduce pressure at

the outlet to the level of 3.5 kg / sqcm

complete as required .

7 18.16 Supplying and Fixing 63 mm dia 15 m Long

RRL Hose pipe with 63 mm dia male and

female coupling duly bound with GI wire ,

rivet etc . Conforming to IS : 636 ( Type A )

7.1 18.16.1 Gunmetal Material 3.00 Set 5202.00 15606.00

8 18.17 Supplying and Fixing First aid hose reel with

MS Construction Spray painted in Post office

red conforming to IS : 884 complete with the

following as required

20 mm nominal internal dia water hose

thermoplastic ( Textile Reinforced ) Type - 2

as per IS : 12585

20 mm nominal internal dia gunmetal globe

valve and nozzle

Drum and Brackets for fixing the equipments

Connections from Riser with 25 mm dia stop

gunmetal valve and MS Pipe and socket

9 18.18 Supplying and Fixing 63 mm dia Gunmetal

Short Branch Pipe with 20 mm nominal

internal diameter size nozzle conforming to

IS : 903 suitable for instantaneous

connection to interconnect hose pipe

coupling as required .

9.1 18.18.1 Gunmetal Material 6.00 Set 2416.00 14496.00

10 18.22 Providing and Fixing of Pressure Switch in

MS Pipe Line including connection etc as 1.00 Each 1546.00 1546.00

11 NS-1 Providing and fixing of Fire Hose Cabinet size

not less than 2.1 x 1.2 x 0.90 mtr made out

of M.S. sheet not less than 1.5 mm thick

having central opening and 4 mm thick

glazed glass doors (Two nos.) suitably

marked on the outside 'with the letters

"FIRE HOSE" including necessary locking 3.00 Each 30495.00 91485.00

arrangement and painting in PO red colour

suitable to accommodate, internal hydrant

valve, 2 nos 15 mtr long Hose pipe,

branch pipe, nozzle and fire man's axe. It

shall be fixed inside the FHC Cabinet

Complete as required .

12 NS-2 Providing and fixing weather proof Fire Hose

Cabinet of size not less than 0.75 x 0.6 x

0.25 mtr made out of M.S. sheet not less

than 1.5 mm thick having central opening

and 4 mm thick glazed glass doors (Two

nos.) suitably marked on the outside 'with

the letters "FIRE HOSE" including necessary

locking arrangement and painting in PO red

colour suitable to accommodate, external

yard hydrant valve, 2 nos 15 mtr long

Hose pipe, branch pipe, nozzle and fire

man's axe. It shall be mounted on boundary

wall complete as required.

13 NS-3 Providing & fixing Controlled Percolating

(CP) Hose ISI marked (IS:8423) 63 mm dia

x 15 m long complete with instantaneous

type Stainless steel 63 mm dia ISI marked

Male & Female couplings (IS:903) bound and 6.00 Each 5081.00 30486.00

riveted to hose pipe with copper rivets and

1.5 mm copper wire.brusting pressure not

less than 22 Kg/Sqcm. ( Two nos. for each

14 NS-4 Providing and fixing standard firemans axe

with heavy rubber handle.

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

15 NS-5 Providing and fixing dial type pressure

gauge with isolation cock and copper pipe Each 3458.00 41496.00

on main header Dial diameter 100 mm

celebration 0-16 / sq. cm.

16 NS-6 Providing and fixing Fire Extinguishers (CO2

type powder ) 4 Kg Capacity complete with Each 5647.00 5647.00

all accessories as per manufacturers

specifications.

17 NS-7 Providing and fixing Fire Extinguishers (A,

B, C type powder ) 5 Kg Capacity complete Each 4518.00 63252.00

with all accessories as per

manufacturers specifications.

FIRE ALARM CONVENTIONAL SYSTEM

Supplying, installation, testing &

commissioning sector panel suitable for

following zones, complete with visual

1 DSR 17.1.9 indications for short circuit fault, open circuit

fault, fire condition and all other standard

facilities as per IS:2189 with mimic diagram

for all area/zone covered, complete with all

connections, interconnections as required

Supplying, installation, testing &

commissioning of conventional beam

2 NS-1 detector with short circuit isolator (inbuilt or 2.00 Nos. 43644.00 87288.00

seperate) complete with emitter and receiver

including connections with remote test

features etc complete as

Supplying, installation, testing &

commissioning of smoke detector with

builtin LED and mounting base complete

with all connections etc. as required

Supplying, installation, testing &

commissioning of manual call boxes of MS

4 DSR 17.1.3 construction in surface/recess with stainless 4.00 Nos. 474.00 1896.00

steel chain & hammer assembly complete

with glass and push button etc. as required.

Supplying, installation, testing &

commissioning fire alarm sounder with

facility to make announcement, mounted in

5 DSR 17.1.6 M.S. box (16 SWG) with hinged cover plate 4.00 Nos. 557.00 2228.00

& suitable for operation with amplifier i/c

line matching transformer etc. complete as

Supplying & laying of 2x1.5 sqmm fire alarm

armoured cable, 600/1000V rated with

6 DSR 17.5.2 annealed copper conductor having XLPE 160.00 Mtrs 173.00 27680.00

insulation, steel wire armouring & FRLS

outer sheath complete as required.

Supplying and fixing of following sizes of

steel conduit along with accessories in

7 DSR 1.20 surface/recess including painting in case of

surface conduit, or cutting the wall and

making good the same in case of recessed

conduit as required.

Supply, Installation, Testing &

Commissioning of Speaker with below

Specifications:-

Transducer Size : 15" LF Driver + 1 x 1"

Horn-loaded Compression Driver

Power Handling : 300 Watts Continuous,

Freq. Range : 75 Hz - 21 kHz

Dispersion : 90 x 40

Sensitivity : 101 dB

Max SPL : 124dB continuous, 130 dB peak

Approved Makes: OHM, British Acoustics,

JBL, Bose, Honeywell

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Supply, Installation, Testing &

Commissioning of Subwoofer with below

Specifications:-

Transducer Size : 18" Low Frequency Driver

Power Handling : 600 Watts Continuous,

Dispersion : Omni-directional,

Sensitivity : 101 dB

Max SPL : 129dB continuous, 135 dB peak"

Approved Makes:OHM /British Acoustics/

Bose/ British Acoustics

Supply, Installation, Testing &

Commissioning of Class-D Power Amplifier

with below Specifications:-

Number of Channels : 2

Power at 4 Ohms per channel : 1000W

NS Power at 8 Ohms per channel : 500W 2.00 Nos 90000.00 180000.00

Class-D with LCD Display for critical factors,

dual step power factor correction, built in

crossover to set HPF & LPF Filters

Approved Makes: OHM /British Acoustics/

Bose/ British Acoustics

Supply, Installation, Testing &

Commissioning of Software Controlled

Digital DSP with below Specifications:-

Number of Inputs - 4,

Number of Outputs - 8,

Input Impedance - 12kΩ unbalanced, 24 kΩ

NS balanced 1.00 Nos 80000.00 80000.00

Adjustable Delay - 1 second / input & 1

second / output

Approved Makes: OHM /British Acoustics/

Bose/ British Acoustics

3 NS Supply of Flying bar for above speakers 2.00 Nos 20000.00 40000.00

Supply of Stage Monitor Supply of Stage

monitor 2-way, bi-amp. bass reflex design,

400+100W rms , 75Hz-16KHz freq resp, 12"

4 NS woofer, 1"HF driver, 130dB SPL max, Disp 2.00 Nos 46000.00 92000.00

90°, polyprop molded enclosure . Approved

Makes: OHM /British Acoustics/ Bose/ British

Supply of Audio mixer 24 mono mic inputs 4

line inputs Freely assignable faders and

patching Pre/Post selection per input per bus

AES in and out Global mode encoders

FaderGlow™ GEQ on every bus 20 sub-group

/ aux busses 4 FX busses 8 Matrix busses LR

5 NS and C Mix busses 4 Stereo Lexicon Effects 1.00 No. 86000.00 86000.00

engines Delay on inputs and outputs 4 Mute

Groups Freely assignable insert loops

Harman HiQnet integration Colour touch

screen interface Approved Makes: (Si

Expersion-2)(Allen Heath QU 24)/ (OSL

Supply of Corded microphone (Shure-

SM58/OSL/sennheiser)

Supply of Instrument Microphone(Shure-

57/OSL/sennheiser)

Supply of Podium Microphone

(Shure/OSL/AKG)

9 NS Supply of Microphone Stand Big(GS) 2.00 Nos 1124.00 2248.00

10 NS Supply of Microphone Stand Small(GS) 2.00 Nos 843.00 1686.00

Supply of microphone cable from stage to

control room for microphone points with Mtr 80.00 24000.00

conduit pipe etc. (Belden/Klotz/Netmas)

Supply of Speaker 2.5sqmm x3core

(Belden/Klotz/Netmas)

Supply of microphone connecting box made

out from CRC sheet metal box duly powder

13 NS coated paint,with 6 nos XLR panel mounting 4.00 Nos 6322.00 25288.00

socket & phono socket having the facility to

connect the 6nos microphone channel.

Supply of Professional Head phone(German

14 NS Meastro/Sennheiser/OSL) 1.00 Nos 7170.00 7170.00

Supply of Microphone cable XLR to XLR up

to 10 Mtr (Belden/Klotz/Netmas)

Supply of Microphone cable XLR to XLR up

to 15 Mtr (Belden/Klotz/Netmas)

Supply of Speaker connectin connector &

MCB Box for Speaker etc

18 NS Installation charges 1.00 Job. 80000.00 80000.00

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

SUB TOTAL 1219768.00

EXTERNAL DEVELOPMENT WORK

A PQC ROAD FOR 3.5 MTR WIDE & 10.0 MTR LONG ROAD

Preparation and consolidation of sub grade

with power road roller of 8 to 12 tonne

capacity after excavating earth to an

average of 22.5 cm depth, dressing to

1 16.1 camber and consolidating with road roller 55.00 Sqm 218.90 12039.50

including making good the undulations etc.

and re-rolling the sub grade and disposal of

surplus earthwith lead upto 50 metres.

Construction of granular sub-base by

providing close graded Material conforming

to specifications, mixing in a mechanical mix

plant at OMC, carriage of mixed material by

tippers to work site, for all leads & lifts,

2 16.78 spreading in uniform layers of specified cum

thickness with motor grader on prepared

surface and compacting with vibratory power

roller to achieve the desired density,

complete as per specifications and directions

of Engineer-in-Charge.

With material conforming to Grade-I (size

3 16.78.1 range 75 mm to 0.075 mm) having CBR 3.50 cum 2784.00 9744.00

Construction of dry lean cement concrete

sub base over a prepared sub-grade with

coarse and fine aggregate conforming to

IS:383, the size of coarse aggregate not

exceeding 25 mm, aggregate cement ratio

not to exceed 15:1, aggregate gradation

after blending to be as per specifications,

cement content not to be less than 150

Kg/cum, optimum moisture content to be

determined during trial length construction,

concrete strength not to be less than 10 Mpa

at 7 days, mixed in a batching plant,

transported to site, for all leads & lifts, laid

with a mechanical paver, compacting with 8-

10 tonne vibratory roller, finishing and

curing etc. complete as per direction of

Engineer in- charge.

Providing and laying C.C. pavement of mix M-

25 with ready mixed concrete from batching

plant. The ready mixed concrete shall be laid

and finished with screed board vibrator ,

vacuum dewatering process and finally

finished by floating, brooming with wire

brush etc. complete as per specifications and

directions of Engineer-incharge.

(The panel shuttering work shall be paid for

(Note:- Cement content considered in this

item is @ 330 kg/cum.

Excess/less cement used as per design mix

is payable/ recoverable separately).

Providing and filling in position rubberized

bitumen hot sealing compound for sealing of

expansion joints in roads / pavements all

6 16.46.1 complete as per direction of the Engineer-in-

Per cm width percm depthper mlength

Using grade 'A' sealing compound

conforming to IS: 1834

Providing and laying at or near ground level

factory made kerb stone of M-25 grade

cement concrete in position to the required

line, level and curvature, jointed with

cement mortar 1:3 (1 cement: 3 coarse

sand), including making joints with or

without grooves (thickness of joints except

at sharp curve shall not to more than 5mm),

including making drainage opening wherever

required complete etc. as per direction of

Engineer-in-charge (length of finished kerb

edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved

by Engineer-in-charge).

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Excavating, supplying and filling of local

earth (including royalty) by mechanical

transport upto a lead of 5km also including

8 2.25a ramming and watering of the earth in layers 8.50 cum 700.50 5954.25

not exceeding 20 cm in trenches, plinth,

sides of foundation etc. complete.

Painting with synthetic enamel paint of

approved brand and manufacture of required

colour to give an even shade :

Two or more coats on new work over an

under coat of suitable shade with ordinary sQM 226.25 2036.25

paint of approved brand and manufacture

FOOTPATH 2.00 MT. WIDE(FOR 10.00 X

1. Earth work in excavation by mechanical

means (Hydraulic excavator) / manual

means over areas (exceeding 30cm in depth.

1.5 m in width as well as 10 sqm on plan)

including disposal of excavated earth, lead

upto 50m and lift upto 1.5m, disposed earth

to be levelled and neatly dressed.

2.6.1 all kinds of soil 10.63 Cum 177.50 1887.05

2 Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering. All work

upto plinth level.

1:5:10 (1 cement : 5 course bound: 10

graded stone aggregate 40mm nominal size) 10.97 Cum 6518.60 71500.89

3 16.68 Providing and laying 60mm thick faciory

made cement concrete interlocking paver

block of M -30 grade made by block making

machine with strong vibratory compaction,

of approved s;ze, design & shape, laid in

required colour and pattern over and 112.50 Sqm 972.00 109350.00

including 50mm thick compacted bed of

coarse sand, filling the joints with line sand

etc. all complete as per the direction of

Engineer-in-charge.

4 Providing and laying at or near ground level

factory made kerb stone of M-25 grade

cement concrete in position to the required

line, level and curvature, jointed with

cement mortar 1:3 (1 cement: 3 coarse

sand), ncluding making joints with or

without grooves (thickness of joints except

at sharp curve shall not to more than 5mm), 5.06 Cum 10117.60 51220.35

including making drainage opening wherever

required complete etc. as per direction of

Engineer-in-charge (length of finished kerb

edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved

by Engineer-in-charge).

5 Painting with synthetic enamel paint of

approved brand and manufacture of required

colour to give an even shade :

Two or more coats on new work over an

under coat of suitable shade with ordinary 16.88 Sqm 226.25 3817.97

paint of approved brand and manufacture

6 Excavating, supplying and filling of local

earth (including royalty) by mechanical

transport upto a lead of 5km also including

ramming and watering of the earth in layers 30.38 Cum 700.50 21277.69

not exceeding 20 cm in trenches, plinth,

sides of foundation etc. complete.

7 Filling available excavated earth (excluding

rock) in trenches, plinth, sides of

oundations etc. in layers not exceeding

20cm in depth, consolidating each deposited

layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

8 Centering and shuttering including strutting,

propping etc. and removal of form for all

a Foundations, footings, bases of columns,

5.9.1 etc. for mass concrete.

SUB HEAD- V EXTERNAL WATER SUPPLY

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

MR Supplying, installing, testing and

commissioning vertical on line multi stage

centrifugal pumping set with mechanical

seal, C.I. volute and SS impeller & SS shaft

connected to a TEFC induction motor of

suitable HP for 415 volts, 3 phase, 50 cycles

A.C. supply with 150 mm dia pressure gauge

with SS/gunmetal isolation cock, vibration

eliminating pads, base plate wiring upto

panel and equipment for water level

controller to start and stop the pump

automatically at predecided levels of the

water in the tank with provision of protection

for dry run etc. complete in all respect (The

shop drawing or the pumps along with its

characteristics curves, model and technical

data etc. are to be submitted for approval

before purchase of pump).

Domestic water pumps (Treated water

transfer pump to terrace tank) (1W+1S)

Capacity 50 lpm

18.10 Providing and fixing G.I. pipes complete with

G.I. fittings and clamps, i/c cutting and

making good the walls etc.

Internal work - Exposed on wall

18.10.6 50 mm dia nominal bore 21.00 RMT 1048.35 22015.35

18.12 Providing and fixing G.I. pipes complete with

G.I. fittings including trenching and refilling

SUB HEAD- IV EXTERNAL SEWARAGE LINE

2.1 Excavating trenches of required width for

pipes, cables, etc including excavation for

sockets, anddressing of sides, ramming of

bottoms, depth up to 1.5 m, including

getting out the excavated soil, and then

returning the soil as required, in layers not

exceeding 20 cm in depth, including

consolidating each deposited layer by

ramming, watering, etc. and disposing of

surplus excavated soil as directed,within a

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but

not exceeding 300 mm dia

19.4.1.1 Providing and fixing square-mouth S.W.

gully trap class SP-1 complete with C.I.

grating brick masonry chamber with water

tight C.I. cover with frame of 300x300 mm

size (inside) the weight of cover to be not

less than 4.50 kg and frame to be not less 7.00 EACH 2707.65 18953.55

than 2.70 kg as per standard design:

100x100 mm size P type. With common

burnt clay F.P.S. (non modular) bricks of

class designation 7.5

19.7 Constructing brick masonry manhole in

cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), foundation

concrete 1:4:8 mix (1 cement : 4 coarse

sand : 8 graded stone aggregate 40 mm

nominal size), inside plastering 12 mm thick

with cement mortar 1:3 (1 cement : 3

coarse sand) finished with floating coat of

neat cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal

size) finished with a floating coat of neat

cement complete as per standard design :

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

19.7.1 Inside size 90x80 cm and 45 cm deep

including C.I. cover with frame (light duty)

455x610 mm internal dimensions,total

weight of cover and frame to be not less

than 38 kg (weight of cover 23 kg and

weight of frame 15 kg) :

19.7.1.1 With common burnt clay F.P.S.(non

modular) bricks of class designation 7.5 8.00 EACH 12770.55 102164.40

19.28 Constructing brick masonry road gully

chamber 45x45x77.5 cm with bricks in

cement mortar 1:4 (1 cement : 4 coarse

sand ) with precast R.C.C. vertical grating

complete as per standard design :

19.28.1 with common burnt clay F.P.S.(non module)

brick of class designation 7.5

19.1 Providing, laying and jointing glazed

stoneware pipes class SP-1 with stiff mixture

of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of

joints etc. complete :

19.2 Providing and laying cement concrete 1:5:10

(1 cement : 5 coarse sand : 10 graded stone

aggregate 40 mm nominal size) all-round

S.W. pipes including bed concrete as per

standard design :

19.16 Providing orange colour safety foot rest of

minimum 6 mm thick plastic encapsulated

as per IS : 10910, on 12 mm dia steel bar

conforming to IS: 1786, having minimum

cross section as 23 mmx25 mm and over all

minimum length 263 mm and width as 165

mm with minimum 112 mm space between

protruded legs having 2 mm tread on top

surface by ribbing or chequering besides

necessary and adequate anchoring

projections on tail length on 138 mm as per

standard drawing and suitable to with stand 24.00 EACH 553.70 13288.80

the bend test and chemical resistance test as

per specifications and having manufacture's

permanent identification mark to be visible

even after fixing, including fixing in

manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse

sand : 6 graded stone aggregate 20 mm

nominal size) complete as per design.

19.21 Making connection of drain or sewer line

with existing manhole including breaking

into and making good the walls, floors with

cement concrete 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20

mm nominal size) cement plastered on both

sides with cement mortar 1:3 (1 cement : 3

coarse sand), finished with a floating coat of

neat cement and making necessary channels

for the drain etc. complete :

19.21.1 For pipes 100 to 250 mm diameter

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

19.9 Constructing brick masonry circular type

manhole 0.91 m internal

dia at bottom and 0.56m dia at top in

cement mortar 1:4 (1 cement

: 4 coarse sand), inside cement plaster 12

mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand)

finished with a floating coat

of neat cement, foundation concrete 1:3:6

mix (1 cement : 3 coarse

sand : 6 graded stone aggregate 40 mm

nominal size), and making

necessary channel in cement concrete 1:2:4

(1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm

nominal size) finished

with a floating coat of neat cement, all

complete as per standard

19.9.1 0.91 m deep with SFRC cover and frame

(heavy duty, HD-

20 grade designation) 560 mm internal

diameter conforming

to I.S. 12592, total weight of cover and

frame to be not

less than 182 kg., fixed in cement concrete

1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate

nominal size) including centering, shuttering

(Excavation, foot rests and 12mm thick

cement plaster at

the external surface shall be paid for

19.9.1.1 separately)

With common : burnt clay F.P.S. (non

bricks of class designation 7.5

SURFACE DRAIN (250X150 MM)

1 Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in-charge.

2.6.1 all kinds of soil 43.00 cum 177.50 7632.50

2 Filling available excavated earth (excluding

rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding

20cm in depth: consolidating each deposited 11.00 cum 196.00 2156.00

layer by ramming and watering, lead up to

50 m and lift up to 1.5 m.

Qty. = 25% of them no 1

3 Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shttering - All work up

4.1 to plinth level

1:5:10 (1 cement : 5 coarse sand (zone-III):

10 graded stone aggregate 40 mm nominal 9.00 cum 6518.60 58667.40

4 1:2:4 (1 Cement : 2 coarse sand (zone-III)

derived from natural sources : 4 graded

stone aggregate 40 mm nominal size derived 3.00 cum 7780.30 23340.90

from natural sources)

5 Centering and shuttering including strutting,

propping etc. and removal of form for all

Foundations, footings, bases of columns,

5.9.1 etc. for mass concrete

6 Brick work with F.P.S. bricks of class

designation 75 in foundation and plinth in :

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse

7 12 mm cement plaster finished with a

13.7 floating coat of neat cement of mix :

External Electrification

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Earthing with G.I. earth plate 600 mm X 600

mm X 6 mm thick including accessories, and

providing masonary enclosure with cover

1 DSR 5.4 plate having locking arrangement and 1.00 Sets 7472.00 7472.00

watering watering pipe 2.7 metre long etc.

with charcoal/ coke and salt as required.

Earthing with Cu. earth Plate 600mm x

600mm x 3mm thick including accesssories,

and providing masonary enclosure with

2 DSR 5.6 cover plate (CI heavy duty) having locking 1.00 Sets 13838.00 13838.00

arrangement and watering pipe pipe of 2.7

mtr long etc. with charcoal or coke and salt)

Supplying and laying 25 mm X 5 mm G.I.

strip in 40 mm dia G.I. pipe from earth

3 DSR 5.11 electrode, including connection with G.I. nut, 20.00 Mtr 706.00 14120.00

bolt, spring, washer excavation and refilling

etc. as required.

Providing and fixing 25 mm X 5 mm copper

strip on surface or in recess for connections

4 DSR-5.14 etc. as required. 2 nos used for 50 x 5 for 20.00 Mtr 1162.00 23240.00

the Neutral earthing of euipments )

Providing and fixing 25 mm X 5 mm G.I.

5 DSR 5.15 strip on surface or in recess for connections 20.00 Mtr 244.00 4880.00

etc. as required.

Providing and fixing 6 SWG dia G.I. wire on

6 DSR 5.16 surface or in recess for loop earthing etc. as 20.00 Mtr 70.00 1400.00

Supplying, fixing, testing and commissioning

of following bare Copper/ GI flat including all

7 NSI-1 necessary fixing accessories and effecting

Supply and laying medium class GI pipe

under road/paved areas/wall crossing etc.

8 NSI-2 including earth excavations refilling,

ramming and making good as approved.

8.1 NSI-2.1 150 mm dia GI pipe Class B 10.00 Metre 1600.00 16000.00

SUPPLYING & LAYING OF CABLE

Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade

of following size direct in ground including

1 DSR 7.1 excavation, sand cushioning, protective

covering and refilling the trench etc. as

Laying of one number additional PVC

insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size direct

2 DSR 7.2 in ground in the same trench in one tier

horizontal formation including excavation,

sand cushioning, protective covering and

refilling the trench etc. as required.

Supply of following sizes of XLPE insulated

Aluminum conductor strip/ wire Armoured,

3 NSI overall PVC sheathed 1.1 KV grade cables

conforming to relevant IS-7098 Code and

technical specifications.

Supplying and making end termination with

brass compression gland and aluminium lugs

for following size of PVC insulated and PVC

4 DSR 9.1 sheathed / XLPE aluminium conductor cable

of 1.1 KV grade

DSR RATE AMOUNT

S.N Description QTY Unit

ITEM CODE DSR MR DSR MR AMOUNT

Supplying, installation, testing and

commissioning of 65W LED Street Light

IP66 LED with High performance having

system lumen output of minimum 9900

lumens, contemporary designed housing

1 NSI-1 made of die-cast aluminium, with street 4.00 Nos 7634.33 30537.32

optic LENS for uniform light distribution. PF

better than 0.9, CRI better than 70 complete

with all accessories. Wipro Cat No.: LR 02-

102-XXX-57-G2 Street light

SITC of 6m ht. GI pole alongwith control

2 NSI-2 box,6A MCB etc. as required for St. height 4.00 Nos 10000.00 40000.00

GRAND TOTAL 42450791.16

GRAND TOTAL 42450791.16