SPECIAL REPAIR TO BATHROOM BLDG NOS T-312 (A SQN), T-313 (B SQN), T-318 (C SQN) AND T-319 OF THE REGT AT MAMUN MIL STATION

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for Solid PVC Door Frame of size 50mm x 47mm (suitable for moulded door) made out of 5mm wood grain printed PVC sheets & edges will be painted to match printed sheet as reinforced with 19mm square MS tube and fixing in opening as specification & drawing complete all as specified and directed.

M&L two coats of synthetic enamel paint on old steel surfaces of any description, n . exc. 10cm in width or girth, including preparation of surfaces, complete all as specified and directed

Dismantling of Asbestos cement sheet (Corrugate, semi corrugated) as in roof covering complete all as specified as directed

M&L for Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing sheets of any type and description complete all as specified and directed [Note : The colour of sheet shall be as approved by GE].

M&L for Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick having tensile strength of 550 Mpa as in ridge fixed with self tapping screws including dismantling of existing sheets of any type and description complete all as specified and directed [Note : The colour of sheet shall be as approved by GE].

M&L for Factory made solid pannel PVC door shutter (Wood grain colour sheets on both sides) 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour & as gap insert for top rail & bottom rail Panelling of wood grain colour sheet to be fitted in MS frame welded / sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cment, supplying & fixing in the frame complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom railon either side and as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement for wire gauzed i.e panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm MS soild tube and this tube shall be welded to MS tubes. The wire gauze shall be stretched to tighten firmly, complete all as specified and as directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 200mm long , complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150 mm complete all as specified and directed.

M&L for 300 mm aluminium alloy sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section complete all as specified and directed.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. (Make :- Paryag/Polytuf)

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in panels and joints filled with mix of bitumen and sand (1:2) by weight, finished the surface even and smooth using extra cement complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 7 to 8mm thick as in floor area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) iincluding dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 350mm x 250mm/ 450mmx300mm on vertical surfaces such as in dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

Taking up or down 15mm bore pipe and connections including cleaning for refixing including all new fittings for 15mm bore complete all as specified & directed.

Taking up or down 20mm bore pipe and connections including cleaning for refixing including all new fittings for 20mm bore complete all as specified & directed.

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Refixing of old steel tubing 20 mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) fixed to wall , floor etc complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting chases not exceeding 10cm in width/girth for concealed water tubing or concealed conduit wiring etc and making good in cement mortar 1:3 to match existing surface etc complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

M&L for Brick work (except brick) straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed. Note : Brick retrived from dismantling to be re-used in the work

Taking down cement or cement lime plaster of any description and removal of rubbish out off the premises, complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm in 1: 6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement complete all as specified & directed.

M&L for 20 mm bore gun metal gate valve, with cast iron wheel head, screwed both ends for GI pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crotch or butterfly handles screwed down complete all as specified and directed.

S&F in repair for Vitreous china White Squatting Orissa Pattern pan (Make : Somany Cat part No 121115 or equivalent Cat Part/Modelof Hindware/Parryware) of size 580x440mm, including cast iron ‘P’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe including provision of cement concrete 1:5:10 type E2 bedding including demolition complete all as specified and directed.

S&F in repair PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with or without ears laid in floors with cement joints complete all as specified and directed.

S&F in repair for 50 mm bore, sand cast, cast iron soil, waste and vent pipe with or without cement joints, in any length with ears, fixed to wall with stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nuts complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius) oval type, complete all as specified and directed.

S&F in repair 100mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with ovel asses door complete all as specified and directed

S&F in repair for 100 mm Cast iron floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with or without hole complete all as specified and directed.

S&F in repair 75 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall after complete removal of existing treatment making the surface smooth and apply two coats of cement based paint over a coat of alakli resistance primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and apply two coats of cement based paint over a coat of alakli resistance priming paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and apply three coats of white wash on plastered surfaces complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for one light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 50 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S & F modular switch piano type flush button one way 06/10 Amp one module complete all as specified and directed. Make : Legrand Cat Part No 673000/Crabtree Cat Part No ACMSXXW101/Anchor Roma Cat Part No 66111.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 50x20mm, three terminals, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 39040 or equivalent of Havells(Reo)/SSK (Topline)/GM (Vyoma)

S&F in replacement white poder coated CRCA box with decorative end cap batten alongwith LED T8 tubular lamp 20W linear with extruded aluminium/pc body and PC diffuser and inbuilt driver, 230 volts wall mounted complete with all accessories internally pre wired and including connecting up with three core twisted flexible copper conductor cable of suitable size including taking down old UNSV tubelight fitting any type. Make of batten-Crompton batten Cat Part No DMLN1LT8-16 and LED tube Rod Cat Part No LTT8-20 or Equivalent model in other makes given here-in-after.

S &F in repair the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 14W LED lamp for approved make and cat part and PVC Round/Square block etc complete all as specified and directed Notes : 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 50,000 burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F in replacement sheet metal enclosure with single pole and neutral enclosure with two pin and earth plug socket complete with one MCB SP 20 Amps 240 Volts complete all as specified and directed. Make : Legrand/Indoasian/Schneider.

S&F heavy duty exhaust fan AC single phase 230/240 Volts of size 300mm sweep with louvre of plastic body with grouting nut bolts and making the suitable hole for 300mm sweep exhaust fan by breaking the existing wall and making good the disturbed surface by plastering and matching with existing specifications all as specified and directed. Make : Havells Ventil Air- DB, Crmpton, Orient

S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 Sq mm, 2 Core laid under ground, fixed along wall, through GI pipe under floor/Road including dismantling existing service cable of any size from electric pole to building, complete all as specified and directed by EIC. Make of cable : Havells, Polycab, Gloster Cables Ltd

M&L for tube, light grade galvanised with all fittings laid in trenches/through wall/under road or floor of 40 mm bore. Make : TATA/Jindal/Ravindra

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

M&L for sand filling in trenches dry and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed (Note : Punned thickness shall be measured & paid)

M&L for well burnt bricks, laid flat (old size) sub class B designation 75 for cable protection complete all as specified and directed

Supply and Install the electric water heater storage type 50 Ltr capacity 5 Star rated of vertical type glass lined of inner tank and heating element of 2kW and having the wall mounting arrangement, thermostate, indicators and thermally insulated stainless steel tank of glass lined inside the tank and heating element, PVC connection pipe with complete connection of water & testing and all as specified and directed. Make : Havells Monza DX or equivalent model in Crompton, Racold

S&F Double door MCB DB SPN, 240 Volts, 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar fixed flush in wall including chases wall for fixing DB and making good disturbed wall surfaces including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-04 or equivalent model in L&T/Hager/SCHNEIDER

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole and neutral(SPN) 240 volts, 6 to 32 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

dadwal engineers

M/S INDIAN ELECTRICAL

M/S CANTILEVER ENGINEERS

Alishan Builders

M/s Rajeev Vashist

M/S J N TRADERS

D R CONTRACTORS

abrol enterprises