Sub Jail at Solan distt solan hp

Amount

Cutting in earth work through mechnical means in all heights/depths and in all kinds of soil such as kankar, moorum, shingle and decomposed of soft or hard rock i.e. their intermediate classification of soil & chiselling/wedging out rock where blasting is prohibited including saturated soil and filling in embankments etc. where necessary and disposal of all excavated unserviceable material in all leads & lifts through mechanical transporation. Any damage to the private / public property during execution will be restored by the contractor whatsoever the nature of the same may be.The serviceable materials will be stacked in specified dimensions in all leads and lifts as per the direction of the Engineer-in-charge.

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work, blasting work and chiselling / wedging out of hard or soft rock where blasing is prohibited up to all depths stacking the excavated soil not more than 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Excavation in earth work in alll kind of soil such as Pick Work/ Jumper Work including Chiselling/Wedging out of hard or soft rock where blasting is prohibited and disposal of all excavated earth in all leads and lifts through mechanical trasportations, disposed earth to be levelled and neatly dressed as directed by Engineer-in-charge.

Excavation in drains and channels etc. in earth work including dressing of side and bed and disposing of excavated earth upto all lead and lift and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Filling in plinth with sand under floors including watering,ramming, consolidating and dressing complete with cost of sand including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping, etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of material in all leads and lifts.

Foundation, footing bases of columns etc. and mass concrete.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses and string courses and the like.

Columns, pillars, posts and struts square, rectanagular or polygonal in plan.

Flat surfaces such as soffits of suspended floors, roofs including inclined surfaces up to any degree, landings and the like:(i)Floors, etc. upto any thickness.

Beams, cantilevers, girders and lintels sides and soffits of beams, small ends of beams,beam haunching, cantilivers, girders, bressumers and lintels of any depth.

Stair cases with sloping or stepped soffits excluding landing.

Edges of slabs and breaks in floors and walls under 20cm wide.

Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete (excluding cost of form work) in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 6 : 12 (1 cement : 6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand :16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding cost of form work screed laid under flooring including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand :16 graded stone aggregate 40 mm nominal size) and curing complete under depressed portion including carriage of material in all leads & lifts.

Providing and Laying cement concrete 1:5:10 with 15% plams and curing complete including the cost of farmwork for plain/reinforced concrete in retaining walls, breast walls, the size of plum should be 150 to 300 mm as per drawing and HP.PWD technical specifications including carriage of material in all leads & lifts.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) excluding cost of centring and shutterings per drawing and HP.PWD technical specifications including carriage of material in all leads & lifts. Walls including attached buttresses, pilasters and their caps and bases and string courses etc. upto floor two level:

Applying a coat of hot bitumen (mexphalt 80 / 100 or equivalent) using 1.70 kg per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil including carriage of material in all leads and lifts.

Providing throating, or plaster drip and moulding to RCC chajjas etc. including carriage of material in all leads & lifts.

Providing and laying cement concrete having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curring complete excluding cost of form work and reinforcement for reinforced concrete works including carriage of material in all leads & lifts.

Foundations, footings, bases of column and the like and mass concrete.

Walls (any thickness but not less than 0.10metre thickness) including attached pillasters buttresses,plinth and string courses etc. from top of foundation upto all floor level.

Suspended floor, roofs, landings, shelves and their support, balconies, beams, girders, bressumers and cantilevers in all heights.

Column, pillars, posts and struts upto all heights

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all heights.

Providing & laying cement concrete having strength of M-20 design mixed aggregate mechanically mixed and vibrated for reinforced concrete in chajjas upto any thickness upto all heights i/c finishing the exposed surfaces with cement mortar 1:3 (1 cement : 3 sand) to give a smooth and even surface including centering/form work and curing complete excluding cost of reinforcement including carriage of material in all leads and lifts.

Applying cement slurry on R.C.C . slab or cement concrete work using 2.75 kg of cement per sqm. of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of material in all leads and lifts.

Providing Tor steel /TMT Steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure above plinth level upto all heights in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 sand) including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in superstructure above plinth level upto all heights in cement mortar 1:4 (1 cement: 4 sand) including carriage of material in all leads and lifts.

7.62 Cm. thick brick masonry using 2nd class common burnt clay building bricks in superstructure above plinth level in cement mortar 1:3 (1 cement: 3 sand) including carriage of material in all leads and lifts.

Providing and fixing 100 mm dia PVC pipes for weep holes including carriage of material in all leads & lifts.

Stone filling behind retaining wall including carriage of material in all leads & lifts.

Providing and fixing 125x60mm double rebate door frame fabricated from section roll formed out of 1.2mm thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr. The frame section should be cut to length of mtr joined with corner bracket made of CRCA electroplated . The frame should be provided with 3 Nos . of MS powder coated 4" Butt hinges of 2mm thickness welded to the main frames, 6 Nos. of 1.2 mm thick CRCA electroplated stiffeners should be welded to frame, 6Nos. of 8" MS hold fasts with split end tail welded to stiffner plates, One No. aldrop reciever,each frame should be provided with 25 x 50 mm tie rod at bottom and all welded placed should be treated with protective coat of zinc rich primer and the entire frame should be provided with a coat of etch primer. including carriage of material in all leads and lifts.

Providing and fixing 105x60mm door frame fabricated from section roll formed out of 1.2mm thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr. The overall size of the section should be 105x60mm with rebate of 37mm for shutter. The frame section should be cut to length of mtr joined with corner bracket made of CRCA electroplated . The frame should be provided with 3 Nos . of MS powder coated 4" Butt hinges of 2mm thickness welded to the frames, 6 Nos. of 1.2 mm thick CRCA electroplated stiffeners should be welded to frame. including carriage of material in all leads and lifts.

Providing and fixing Eco 5000 Series (Air Tight with double rebate) Windows fabricated from roll formed section made of galvanized steel colour coated/powder coated (Base steel as per IS 513 "D" QUALITY , galvanized as per IS 277 with Zinc of 120grm per Sqm) with total coated thickness of 0.60mm. Glass shutter and fixed glass portions should be provided with a glass of 4mm Plain Float Glass, Mesh shutter should be provided with a stianless steel 32 gauge fly mesh of 304 grades with 144 holes per square inch. Windows should be provided with grill made of 10mm sq. MS Bars welded to at 150mm center-to-center , 6mmx12mm MS Flat. total grill unit should be powder coated and fixed to window frame with screws.

Providing and fixing 40 mm thick panelled door shutters made of 2nd class deodar wood having styles and top rail 100 mm width and bottom rail 200 mm width, lock rail 150 mm width with pannel insert of 12 mm thick, both side laminated board of approved manufacturer ISI mark, 2nd class deodar wood chamfered beading 40.x12 mm size along the pannels on both side faces of shutter and providing wooden cleats and ISI marked black enamelled M.S. butt hinges with necessary screws all complete as per drawing and specification and instructions of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 40mm thick wire guage shutters using galvanised M.S guage of I.S.guage designation 85 G with wire of dia 0.56mm for doors, windows & clerestory windows including bright finished black enamelled iron butt hinges with necessary screws etc I/c chamfered edged beading 20x12.5mm size.complete including carriage of material in all leads and lifts. (a) 2nd class deodar wood.

Supplying and fixing glass panes with putty and nails including removal of broken glass panes wherever necessary including carriage of material in all leads and lifts.

Providing and fixing bright finished brass 100mm. Mortice latch with one dead bolt and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) including carriage of material in all leads and lifts.

Providing and fixing 19mm thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete) including carriage of material in all leads &lifts.

Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) including carriage of material in all leads &lifts.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel sliding door bolt transparent or dyed to required colour and shade with bolts, nuts and screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel tower bolt (barrel type) annodized transparent or dyed to required shade and colour with screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel handles annodized transparent or dyed to required colour or shade with necessary screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel hand drawn hooks and eyes with necessary screws etc. complete including carriage of material in all leads and lifts. 150mm.

Providing and fixing 100mm Stainless steel floor door stopper with rubber cushion screws etc. to suit shutter thickness complete

Providing and fixing bright finished brass ball catcher 10 mm dia including carriage of material in all leads and lifts.150mm.

Providing & fixing hydraulic door closer as per sample approved by the Engineer-in-Charge with necessary screwes etc.complete including carriage of material in all leads &lifts.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. Brass screws and PVC sleeves etc., wherever necessary complete including carriage of material in all leads &lifts. 20mm dia

Providing & fixing Digital glazed tile i/c border wherever required 8mm thick of any size and any colour as per sample approved by the Engineer-in-Charge i/c cost for cutting the tiles where required in skirting, risers of steps and dado upto all height on 12mm thick cement mortar 1:3 (1cement:3 sand) & jointed with cement slurry i/c carriage of material in all leads and lifts.

Providing & laying granite stone (close grained rounded at edge)in flooring,skirting riser of steps & dado 20mm (average) thickness base of cement mortar 1:3 (1 cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing & polishing complete 20mm thick including carriage of material in all leads & lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant of any size manufactured of approved shade and colour of NITCO, NTC, GICO in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including cost of cutting the tiles where required to be cut i/c carriage of material in all leads & lifts.

Providing and laying (double charged)Duro stone vetrified tiles of any size and colour as approved, thickness not less than 10mm in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles (of any size and any colour/shade) thickness not less than 8mm in skiring, risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stoneaggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat Cement. Including carriage of material in all leads and lifts.

40 mm thick

50mm thick

Extra for providing and fixing glass strips in joints of terrazzo floors including carriage of material in all leads and lifts.40 mm.wide and 6 mm.thick.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including carriage of material in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete Including carriage of material in all leads and lifts.

100mm dia pipe

150mm dia pipe

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete Including carriage of material in all leads and lifts.

PVC Plain bend 100mm dia

PVC Plain bend 150mm dia

PVC shoe 100mm dia

PVC shoe 150mm dia

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) i/c carriage of material in all leads and lifts.

Providing and fixing M.S.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm of 1:2:4:mix (1 cement 2 sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the wall etc i/c carriage of material in all leads and lifts. 150 mm dianetre for PVC pipe

Steel work welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material in all leads and lifts.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars, ladders, railling, brackets and similar works i/c making holes & filling the same with cement concrete 1:2:4 (1 cement:2 sand 4 graded stone aggregate 20mm nominal size).

Providing & fixing stainless steel railing in staicase incuding fixing in position complete as per approved design by ite Engineer-in-Charge i/c carriage of material in all leads and lifts.

Providing & fixing stainless steel 3" dia vertical post in staircase as per sample approved by the Engineer-in-Charge i/c carriage of material in all leads and lifts.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of material in all leads and lifts.(a) With Enamel white paint/ other than white.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting including carriage of material in all leads and lifts. Readymixed paint brushing wood primer pink

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping including carriage of material in all leads and lifts. With enamel white paint/ other than white

Applying Birla white wall care putty over plastered surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of material in all leads and lifts.

6mm cement plaster to ceiling in cement mortar 1:3 (1cement :3sand) including carriage of material in all leads & lifts.

10mm cement plaster in single coat on fair side of brick /stone masonry for interior /exterior plastering upto all heights including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girths and finished even and smooth in cement mortar 1:4(1cement :4sand) including carriage of material in all leads & lifts.

Extra over item of plastering for finishing with a floating coat of neat cement slurry including carriage of materials in all leads and lifts.

15 mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior/exterior plastering upto all heights including arises, Internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 ( 1 cement : 6 sand) including carriage of material in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick / stone masonry for interior/exterior plastering upto all heights including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads and lifts.

Distempering (two coats) with oil bound washable ditemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer ofapproved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer including carriage of material in all leads and lifts.

On Wall.

On Ceiling.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement :3sand :6 graded stone aggregate 20 mm nominal size) including finishing the top surface of concrete smooth complete including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75 mm thick ( unconsolidated) bed of dry bricks/stone aggregate 40 mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads and lifts.

Brick edging (Brick laid on edge) to plinth protection with bricks including grounting with cement mortar 1:4 (1 Cement : 4 Sand) including carriage of material in all leads and lifts. With bricks size 22.9cmx11.2cmx7cm.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts.

Making khurras 45x45cm with average minimum thickness of 5 cm. cement concrete 1:2:4 (1 cement :2 sand: 4 stone aggregate of 20 mm nominal size) finished with 12 mm cement plaster 1:3 (1 cement : 3 sand ) and coat of neat cement rounding the outlet complete including carriage of material in all leads and lifts.

Providing and fixing Cub board Lack including fixing with screws complete in all respects including carriage of material in all leads and lifts.

Providing and fixing 40mm nominal bore GMS Tube(light grade) outlet in cement mortar 1:3(1 Cement: 3 Sand) including carriage of material in all leads and lifts.

Providing chases 75mm wide 50mm deep (average size) in walls for conduit pipes and filling the same with cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregate 20 mm and down gauge) after the conduit pipe is laid (excluding the cost of conduit pipe) including carriage of materialin all leads and lifts.

Providing and fixing to wall ceiling and floor (ISI marked) galvanised mild steel tubes (medium grade)i/c tube fittings and clamps including making good the wall, ceiling and floor including carriage of material in all leads and lifts.

15 mm nominal bore

20mm nominal bore

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40 mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube ittings (earth work in trenches to be measured and paid separately including carriage of material in all leads and lifts.

15 mm nominal bore

20mm nominal bore

Providing and fixing Polythene water storage tank Sintax make for storage of water upto all heights keeping water hygenic & safe for drinking etc. moulded to seamless perfection from FDA approved grades of polythene (LDPE/ HDDE/CLDPE) to BIS-12701-1989 with 40 mm no,minal bore galvanised steel scour with fittings 25mm nominal bore galvanised mild steel overflow tubes tube with fittings and mosquito proof coupling of approved municipal design, 15 mm nominal bore ball valve and mosquito proof galvanised coupling including provising pads of sizes as required and complete tubes as per directions of Engineer-in-Charge including carriage of material in all leads and lifts (a)1000 litres net capacity storage tank of ISI marked sintex make with double.layer including MS Stays for water storage tank.

Providing and fixing high pressure PVC spigot and socket soil, waste and ventilating pipe ISI marked i/c fixing with approved adhensive (i/c PVC clips where ever required) including carriage of material in leads and lifts.

90mm nominal size.

110mm nominal size.

Providing and fixing PVC clamp ISI marked of approved design with steel screws and rawal plugs etc.compoed including carriage of materialin all leads & lifts.

90 mm nominal size

110 mm nominal size

Providing and fixing PVC Plain bend ISI marked complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

P/F PVC Single equal branch ISI marked of required degree with oval access door insertion rubber washer 3mm thick bolts and nuts complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

Providing and fixing PVC Collar i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts

90mm nominal size.

110mm nominal size.

Providing and fixing (ISI marked) PVC Cowl i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts.

90mm nominal size.

100mm nominal size.

110mm nominal size.

Providing and fixing (ISI marked) PVC floor trap of self cleaning design i/c fixing with approved adhensive with C.P. screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors including carriage of material in all leads and lifts.110x90 mm

Providing & fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings Hindware/ Cera make Flat back 550mmx400mm

Providing & fixing C.P. brass waste for wash basin or sink including carriage of material in all leads & lifts.

32mm dia

40 mm dia

Providing and fixing PVC connection pipe Including carriage of material in all leads and lifts.(a) 15mm dia 300/450mm length.

Providing and fixing C.P. connection pipe with brass union Including carriage of material in all leads and lifts.(a) 15mm dia 45 cm. length.

Providing and fixing M.I Union for Wash basin & Sink Including carriage of material in all leads and lifts.

32mm nominal bore

40mm nominal bore

Providing and fixing PVC waste pipe for Wash basin & Sink Including carriage of material in all leads and lifts.

32mm nominal bore

40mm nominal bore

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting including carriage of material in all leads and lifts(i) 610mmx510mm with bowl depth 200 mm

Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers including carriage of material in all leads & lifts.

Providing and fixing C.P. brass towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. brass screws. Including carriage of material in all leads and lifts.600mmx20 mm

Providing and fixing C.P. brass towel ring with Plastic Gitti, Drilling hole etc complete in all respects Including carriage of material in all leads and lifts.

Providing and fixing 600mmx120mm glass shelf with C.P. Brass brackets and guard rail complete, fixed to wooden plugs with C.P. Brass screws. Including carriage of material in all leads and lifts.

Providing and fixing vitreous china wash down water closet (European type W.C. pan) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(1cement: 1sand)plastic seat & cover to be measured & paid for separately confirming to BIS specification Including carriage of material in all leads & lifts (a) Ordinary closet (Universal Closet).

Providing and fixing PTMT Coloured / white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately)including carriage of material in all leads and lifts.

Providing and fixing plastic seat (solid /Hollow type) and cover for wash down water closet with C.P. brass hinges and rubber buffers:- including carriage of material inall leads & lifts. (a) White/coloured plastic seat and cover

Providing and fixing PTMT health shower faucet of approved quality & colour with 1.50 metre tube including screws etc. complete in all respect 15mm dia incliding carriage of material in all leads & lifts.

Providing and fixing C.P. Brass shower rose with 15mm or 20mm inlet Including carriage of material in all leads & lifts 150mm dia

Providing and fixing C.P. Brass bib tap with capstan head short/ long body including carriage of material in all leads and lifts.15mm dia

Long Body

Short Body

Providing and fixing 15 mm C.P. mixer for kitchan sink with top/ bottom swinging spout Including carriage of material in all leads and lifts.

Providing and fixing C.P. Brass angle valve 15 mm without/with nuts Including carriage of material in all leads and lifts.15 mm dia

One way

two way

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap i/c carriage of material in all leads & lifts.

Providing and fixing brass full way valve with wheel Including carriage of material in all leads and lifts.

15mm nominal bore

20mm nominal bore

Providing and fixing G.I./M.I Union of following sizes (Where not included in the items.Including carriage of material in all leads and lifts.

15mm nominal bore

20mm nominal bore

Cutting holes through existing brick work including making good the same in cement mortar 1:6 (1 cement: 6 sand) per CMs depth of cutting (i) Holes upto and including 400 sqcm in area including carriage of material in all leads and lifts

Providing and fixing stoneware gully trap grade 'A' complete with C.I. grating, C.R. masonry in cement mortar 1:6 chamber and water tight C .I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.78kg including carriage of material in all leads and lifts(i) Square mouth trap 100mmx100mm size p type

Constructing chamber 600mm X 450mmX600mm inside sizes for water meter complete with C.I. double Flap Surface box 400mmX 200mm X200mm (inside) with locking arrangments and RCC top slab 1:2:4 mix (1 cement:2 sand:4 graded stone aggregate 20mm nominal size )100mm thick foundation concrete 1:5:10(1cement:5 sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3(1cement:3 sand) finished with floating coat of neat cement including curing complete including carriage of material in all leads and lifts.(a) With 115 mm thick walls brick masonry in cement mortar 1:5(1cement:5 sand)

Providing and fixing Vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material in all leads & lifts.

Providing and fixing toilet paper holder including carriage of material in all leads and lifts.(a) C.P. Brass

Providing anfd fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats/PVC plug with C.P. brass screws Including carriage of materia in all leads and lifts.

Providing and fixing two hole basin mixing Faucet Including carriage of material in all leads and lifts.

Providing and fixing wall mixing faucet for shower and bath with overhead pipe (1210cm) and bath shower including carriage of material in all leads & lifts.

Making connections of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 sand) finished with a floating coat of neat cement and making necessary channels with cement concrete 1:2;4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size ) for the drain complete i/c carriage of material in all leads & lifts. For pipe 100mm to 150mm internal diameter / nominal size

Supplying and fixing S.F.R.C. cover with frame for manholes/RWHT of 560mm internal diameter (Medium duty) the total weight of cover and frmae to be not less than 173 Kg(weight of cover 70 Kg and weight of frame 103 Kg) including carriage of materials in all leads and lifts.

Providing and laying HDPE water pipe 20mm dia including carriage of material in all leads and lifts.

Construction chamber for sluice valve with C.I. Surface box 100mm x160mmx180mm inside with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 75mm thick foundation concrete 1:5:10 (1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete including carriage of material in all leads and lifts. with 230 mm thick walls of brick masonry in cement mortar 1:5(1 cement: 5 sand)

Providing and fixing C.I. Sluice valve(With hand wheel) as per IS-780 class upto 300mm dia (including brass spindle and as per IS:2906 Class-II for diametres more than 300mm complete with bolts , nuts, rubber insertion etc. (the tail pieces if required shall be measured and paid for seperetaly)including carriage of material in all leads and lifts. (a) 150mm nominal size.

Supplying and fixing 1.00 H.P. motor for lifting the water from RWHT to PVC tank including carriage of material in all leads and lifts.

PARDEEP CHAUHAN

suman kumar sharma