REPAIR MAINTENANCE OF CHLORONOME PLANTS PUMP SETS AND AND CONNECTING E N M WKS ESTABLISHMENT N SWIMMING POOL UNDER GE I KANPUR

Amount

Minor repair/cleaning/servicing/maintenance and testing of chlorine granuals based dosing plant comprising of dosing pump, agitator and FRP tank and connected pipe lines etc once in a week for 15 Nos of Installations :- Note : (a) Testing of chlorine at consumer end with medical authority and maintained chlorine test record once a week on a register and submit report to concern JE E&M/Engr-in-Charge. (b) Servicing of Agitator of by using necessary lubricant, replacement of bush/bearing, alingning the shaft , key etc. deemed to be included in item rate. (c) Any other spares required for replacement shall be supplied and fixed under relevent item of Sch 'A'. (d) If any defect found in plant contractor should rectify the defect with in 24 Hrs, if failed to rectify the decfect the contractor shall be liable to pay compensation Rs 500/- (Rupees five hundred only) per plant per day. (e) Cost of minor essential items such as nuts, bolts,washers etc. Which are not otherwise specified in this Schedule but are essential for smooth functioning of the chloronome plants are deemed to be included in the quoted rate. (f) Adequate reserve for all necessary spares /stores will be kept at the site by the contractor to avoid any delay in carrying out the repairs works. (g) All T&P required to carry out the work at site will be provided by the contractor. Cost of the same shall be deemed to be included in the unit quoted rates. (h) All safety precautions including proper gas mask kit will be provided to the technicians by the contractor.

S&F in replacement of Motor 230 volt, 50 Hz, voltage input 230 volt single phase 50 Hz, current consumption 0.4 Ampr power 120 watt, speed 4 pole induction non synchronous 920 RPM Approx under lead motor shaft dia 15mm X Length 50 mm motor is flange mounted 4 no of 7 mm dia hole at PCD 150 mm incl all fixing arrangement.

S&F in replacement of shaft complete with impeller made out of MOC poly propelene rigid dia 32 mm X Length 500 mm impeller type two bladed pitched blade turbine numbar of impeller- I incl all fixing arrangements.

S&F in replacement of Dosing tank only capacity 100 Ltrs MOC PE FRP Ltd contaning port hole for pouring chlorination chemical and water them necessary provision for mounting of moteo at proper angel provision for mounting dosing pump on lid level gauge.

S&F in replacement of Rotor assembly with bearing brackets & tolerance ring complete all as specified and directed.

S&F in replacement of Single head feed rate control with shaft complete all as specified and directed.

S&F in replacement of Pump head ( ferrules 1/4"" & duchbill included) complete all as specified and directed.

S&F in replacement of Pump tube complete all as specified and directed.

S&F in replacement of Injection check valve complete all as specified and directed.

S&F in replacement of Weighted suction line strainer 3/8'' complete all as specified and directed.

S&F in replacement of 3/8'' white suction/discharge tubing complete all as specified and directed.

S&F in replacement of Check valve duckbill only (PK-5) complete all as specified and directed.

S&F in replacement of Gear motor complete 230 volt 50 Hz all as specified and directed.

S&F in replacement of Coil 250 volt 50 Hz complete all as specified and directed.

S&F in replacement of Roller Assembly complete all as specified and directed.

S&F in replacement of dosing pump ( Model No 96 NGQ 51) high pressure single head geared motor adustable dosing having output upto 40 US GPD and pressure upto 7 kg/cm2 with connecing accessories complete all as directed by engineer in charge.

M&L for painting of steel and iron parts of chlorine plant including preparation of old painted surfaces and applying two coat of synthetic enamel paint complete all as directed by Engr-n-Charge. Make of Paint : Asian/Narolac/Burger

Supply only Calcium based high strenght granular chlorination chemical having 65 % to 70 % active chlorine, whitish, free flowing, decomposes clear in water solution , free of foriegn matter , the chlorination chemical should contain appropriate quantities of dispersants, corossion inhibitors to prevent incrustation scaling in distribution systems, mercury and other heavy meatl conteminents in chlorination chemical must be Below Detectable Limit (BDL) Make- PURI CHLOR of M/S Sree Rayalseema Hi-Strength Hypo Ltd or any other make as per E in C approved list

M & L for rewinding of agitator motor of capacity 120 watts, 960 RPM single phase 230 V and using copper winding wire of existing gauge with necessary insulation material including testing after repair and refixing of the same complete all as directed.

Taking / lifting out defective submersible pumps set from bore well complete with column pipe upto 150mm dia steel rope, submersible cable and accessories etc and relowering and commissioning the same after repairing works and testing complete of rating 45/40/30/20 HP 3 phase

Dismantling, taking out complete burnt winding wire of submersible motor including cleaning of stator slots replacement of defective parts and rewinding with existing type & gauge of copper winding wire pvc insulated as per motor capacity and using new insulation material such as insulating paper sleeves etc.replacement of submersible cable as required size/ length complete incl testing all as directed of rating 30 to 45 HP 3 phase.

Dismantling submersible pump, straightening & polishing of pump shaft, making threading and key way, turning surfacing polishing to impellers, CI bowl complete including replacement of worn out parts as per requirement complete incl testing and all as directed of rating 45/40/30/20 HP 3 Phase .

S & F in replacement of Motor bush of gun metal upper and lower for 45/40/30/20HP capacity (Set of two)

S & F in replacement of Rotor bearings sleeve upper and lower for 45/40/30/20 HP capacity, (set of two.)

S & F in replacement of coupling arrangement with key for motor for 45/40/30/20 HP capacity

S & F in replacement of Sand guard for submersible pump set for 45/40/30/20 HP capacity

S & F in replacement of Thrust bearing assembly for submersible pump set motor for the capacity 45/40/30/20 HP

S & F in replacement of Epoxy type cable jointing kit complete with all the jointing material, ferrule, for 1100 volts flat submersible copper conductor cable 16/10 Sqmm 3 core Make : M seal/Reychem/Birla 3 M

S & F of Rubber gasket (packing) suitable for 80 to 150 mm dia flange.

S & F in replacement of MS Nut bolts with spring washers of any sizes.

S & F in replacement of Steel wire rope stranded 12 mm dia for hanging of submersible pump set .

S & F in replacement of Electric cable for submersible pump set, flat 16 Sqmm 3 core stranded copper conductor PVC sheathed cable all as specified and directed. Make- Finolex/ Paragon/Havells

S & F in replacement of impeller with key and distance bushes for 45/40/30/20 HP capacity pump

S & F in replacement of Pump shaft of stainless steel suitable for 45/40/30/20 HP capacity pump

S & F in replacement of NRV for 45/40/30/20 HP capacity pump

S & F in replacement of Bearing bush for submersible pump for 45/40/30/20 HP capacity.

S & F in replacement of Bowl assembly for submersible pump set for the capacity 45/40/30/20 HP

S & F in replacement of Distance sleeves for submersible pump for 40/30/20 HP capacity.

M & L for repair/maint of monoblock pump set of 5/3 HP capacity by means of dismantling from foundation derusting of shaft filling of gland packing replacement of seal bearing etc necessary repair in foundation to make rigid the system and arrest the vibration all as directed.

Dismantling the motor , taking out the burnt copper winding wire of motor 3/5 HP and Rewinding of motor with existing copper wire of existing gauge as per motor capacity using new insulation material such as insulating paper sleeves etc. bakinmg complete with super enamelled insulating varnish including cleaning of stator slots and testing complete, all as directed

Repair/maint of LT panel /Starter of any size/type, checking and tightening of all incoming and outgoing connections by replacing alluminium lugs, pieces of burnt wires as required to make the starter /panel functional .

Replacement of old bus bar any type and S7F copper Bus Bar of 100 A and 415 V, 4 Nos with proper colour coding ing all cable connections with bus bar and breakers (incoming and outgoing) with copper lugs as per site requirement.

S & F in repair MCCB TP, 415V, 100 Amps with breaking capacity 10 KA (as per sample). Make- L&T/Legrand/Siemens/Indo Asian

S & F in repair MCCB TP, 415V, 200 Amps with breaking capacity 25 KA (as per sample). Make- L&T/Legrand/Siemens/Indo Asian

S & F of in repair Power contactor TP as per existing type & make fitted at site for starter suitable for 40 HP/30HP/20 HP submersible pump set. Make- L&T/Legrand/Siemens/Indo Asian

S & F in repair Over load relay (as per sample) for starter suitable for 40 HP/30HP/20HP submersible pump set. Make- L&T/Legrand/Siemens/Indo Asian

S & F in repair Timer (as per sample) suitable for star delta starter for 40/30/25/20 HP submersible pump set. Make- L&T/Legrand/Siemens/Indo Asian

S & F in repair fully automatic star delta starter for submerssible pump set for 40 HP including connecting all incoming and outgoing copper wire as directed . Make- L&T cat part No-MU-G 50 or equivalent to SEIMENS / BCH/Havells

S & F in replacement fully automatic star delta starter for submerssible pump set for 20 HP including connecting all incoming and outgoing copper wire all as directed . Make- L&T cat part No-MU-G 20 or equivalent to SEIMENS / BCH/ Haavells.

S&F in replacement change over switch on load type in open execution front handle operated 415V with rating of 200 Amps four pole 415 volt with box and incl fixing arrangements on wall or panel. Make:-Havells /Legrand/L&T

M&L for Pressure gauge size 100 mm dia round,range 0-10 Kg/cm2 complete with connecting pipe & air cock for 15 mm dia GI pipe.

S&F of swimming pool splash pump with 3 HP motor built in strainer asynchronous, two poles class insulation 130 IP x 5 water proof standard overload protector built in thermal protection, heavy duty with ultra performance to both high and medium head installations, non corrosive materials using NSK bearing, external heat sink to ensure maximum cooling capability, specially made union to incorporate both metric & imperial measurement standard complete all as specified and directed. Mkae : HIBIRD or Equivelent.

S&F of high rate pressure sand filters bobbin wound fibre glass reinforced laminated filter of 1200 mm with UV resistant surface finish, reliable to operate under prolong sunlight for years, designed for easy inspection of quartz filter media with a six position, 50 mm multiport valve and ABS lateral with quartz filter media complete with all required materials incl dismantling of old, all materials as required at site, fixing arrangements and testing on completion all as specified and directed. Make : HIBIRD or Equivelent.

Supply and Fixing in replacement of IP 65 aesthetically appealing vintage LED Post Top Lantern with LEDs as light source of 35/40 W,5700 K including fixing of GI pipe of suitable dia dia, 300 mm long light grade, partly embedded on column of gate with fixing arrangement complete all as specified and directed by the Engr-in-charge complete with electronic driver and provision of three core flexible of 1.50 Sqmm copper conductor cable from ceiling rose to light fitting and other fixing arrangement as required at site complete all as specified and directed..Make:- Bajaj cat part no BGCT W4 LED WW/ Havells cat part no CORALPT35WLED757PSYMTOPC / Wipro cat part no LP 07-431-xxx-57-CL/ C&S Cat part no CETUS / 40W LTGLO40WHPLED/W or equivalent of Philips/ C&G Note : Contractor will submit guarantee/warranty certificate from manufacturer.

M & L for carrying out drinking water test as per IS 10500-2012 (75 parameters) viz, coliform, E coli,aluminium (as Al), arsenic( as As), Boron (as B), Cadmium (as Cd), calcium (as Ca),chloride (as Cl),,total Chromium (as Cr),colour Copper (as Cu),Cyanide (as CN) detergents,Flurides (as F),Iron (as Fe),Lead (as Pb),Deg c,phenolic compounds,residual free chlorine,selenium (as Se),solid dissolved (TDS), Sulphate (as SO4) ,taste,Total Alkalinity,Total Hardness( asCaCo3) ,Turbidity,Zinc (as Zn), ammonia as total ammonia N,Barium (as Ba),chloamines (as Cl2),silver as(Ag), sulphide (as H2S),molybdenum (as Mo),Nickel (as Ni),Trihalomethanes as ( Bromoform, dibron, oehloromethane, bromodichloromethane, chloroform, mineral oil, polychlorinated biphenyl (PCB), polynuclear aromatic hydrocarbons (PAH) Total pesticides residues,radioactivity test( alpha& beta radiation) at an NABL accredited lab and submission of tests reports in 10 days time from date of collection of sample. Note :- 1. Item will be deemed to include collection of water by the lab supervisused in precense of JE/Engg-In-Charge and incl transportation of samples. 2. Lab will be approved by from the GE prior to collection of samples. 3. Location and time of collection will be decided by Engg-in-Charge.

M&L for in renewal earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanised iron strip 32x6 mm as earthing lead by means of boths, nuts check nuts nuts and washers of galvanised or steel all as specified or shown in electrical plate No. 3 of SSR-1( Part-I), including necessary earth work, GI pipe 40mm dia light grade for protection of galvanised iron earthing stripe, etc. with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply compete all as specified and testing of earth resistance as required.

Supply & fixing for GI strip 32x6mm on wall/batten or recessed or buried in ground all as directed by Engineer-in-Charge.

Supply and fixing of LED Aviation Light with all necessary connection all as directed by Engr-In-Charge.Make-Bajaj cat part no BGAV 302 LED/Crompton/Philips

Supply only MS column pipe heavy Duty of size 150 mm nominal dia in standard length of 3.0 mtr, heavy duty duly threaded welded with MS Flange of 12 mm thick on both end with supporting ribs (4 Nos.) including jointing & with new rubber or fiber board gasket with all nuts, bolts and washer set complete all as specified and directed of Make : Jindal/TATA.

S& F (in Replacemnt) Electronic microprocessor based digital & wire less type water level indicator with alarm at time of full level/Low level in tank including all eqpts accomodated in GI sheet box or completely enclosed complete including testing & Commissioning.. Make- Benzer/SAPCON/Aquabrim

M&L for cleaning of RCC over head reservoir 50,000 gallons capacity at 40/60 feet staging including removal of all deposited scales, dirt and settled sand particles from intake of circulating pipe, cleaning with brushing, sweeping and brooming of inner and outer wall of the tank and washing the complete with bleaching powder soluting and M&L for painting to rising main,delivery pipe, wash out and over flow pipes of 150mm bore existing water mains with two coats of synthetic anamal paints and also re-writing date of cleaning and marking of rising & delivery mains etc. Note :- 1. The work shall be carried out through only by trained staff with hygiene and safety equipments. 2. Responsibility for insurance and safety of team will solely rest with the contractor. 3. Cost of temporary supports such as props, jacks, scaffolding etc as required at site is deemed to be included in unit rates quoted.

All as per item No 61 above but 100000 gallons complete.

All as per item No 61 above but 150000 gallons complete.

All as per item No 61 above but 200000 gallons complete.

Supply only sodium hypo chloride ( Chloine percentage 10-11%) for swimming pool water in manufacturer standard packing all as directed. Make- Bihar Coustic & Chemical/Hybird

Supply only Crystal Alum (Ferric) for swimming pool all as spfd.

Supply only Copper Sulphate for swimming pool all as spfd.

Supply only Chemi coat, Algae-cide liquid for swimming pool all as spfd.

Supply only Soda ash (Tech) for swimming pool all as spfd.

Supply only chlorine test kit with coloured sample complete with all testing fitments and 500 ml OT solution as approved complete all as specified and directed.

Repair /maint of suction sweeper pump upto 5 HP cap of swimming pool by filling the gland, minor repair of pump and making pump serviceable by cleaning and greasing after segegating all parts all as specified and directed.

M/S PASHUPATI TRADERS

Himanshu Construction and Suppliers

commercial construction

Preetpowercontrol