Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹77.6 CrAccepted-Finance | ₹77.6 Cr | L1 | Accepted-Finance Lowest rate found. |
| 2 | L2₹78.5 CrAccepted-Finance DADRA AND NAGAR HAVELI DN | DADRA AND NAGAR HAVELI | THE DADRA AND NAGAR HAVELI AND DAMAN AND DIU | 396193 | ₹78.5 Cr | L2 | Accepted-Finance High rate found. |
| 3 | L3₹80.4 CrAccepted-Finance | ₹80.4 Cr | L3 | Accepted-Finance High rate found. |
| 4 | L4₹85.9 CrAccepted-Finance | ₹85.9 Cr | L4 | Accepted-Finance High rate found. |
| 5 | Rejected-Technical | - | - | Rejected-Technical Document not submitted as per tender terms and condition, hence disqualified. |
Tender Value
₹77.0 Cr
EMD Value
₹87.0 L
Closing Date
11 Nov 2020, 2:00 pmClosed
The Exe., Engg., PWD, WD-I, Daman.
The Multi Office Complex, 2nd Floor, Near Moti Daman Market, Moti Daman.
Construction of Academic Block, Student Hostel, Dean Bunglow, Staff Quarters with Ancillary Building and General Development works of Nursing College at Marwad, Nani Daman. (E-30001)
2020_DAMAN_1081_1
Tender Notice No.59/01/E-30001/2020-21
Open Tender
Civil Works
540 days
Daman District.
Please refer Tender documents.
2 documents required · 2 mandatory
₹1,500
The Exe., Engg., PWD, WD-I, Daman.
₹87.0 L
The Exe., Engg., PWD, WD-I, Daman.
13 Feb 2021
28 Sept 2020
11 Nov 2020
28 Sept 2020
11 Nov 2020
28 Sept 2020
13 Oct 2020
Amount
Civil work
01-CIVIL WORKS Sec.1.0 Earth work Providing material and labour, machinery for Excavation of foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excess excavated stuff (after back filling) with in the campus for all lead, all lift/ depth including back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.
Providing material and labour for Excavation of foundation from 1.5 mt to 3.0 mt depth including sorting out and stacking of useful materials and disposing off the excess excavated stuff (after back filling) with in the campus for all lead, all lift/ depth including back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.
Providing material and labour for Excavation of foundation from 3.0 mt to 5.0 mt depth including sorting out and stacking of useful materials and disposing off the excess excavated stuff (after back filling) with in the campus for all lead, all lift/ depth including back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.
Providing material and labour for Excavation of foundation from 5.0 mt to 7.0 mt depth including sorting out and stacking of useful materials and disposing off the excess excavated stuff (after back filling) with in the campus for all lead, all lift/ depth including back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.
Providing material and labour for Disposing off the un-used excavated earth (black cotton soil), debris, malba, dismantled materials for all lead and lift/ depth out side the campus at non objectional place as directed by Engineer in charge.
Providing material and labour for Filling in plinth with sand under floors or base of foundation including watering ramming, consolidating and dressing etc complete as directed by Engineer in charge.
Providing material and labour for Filling in foundation, plinth and plot filling with murrum (brought from out side) in layers of 20cm. thickness including watering, ramming and consolidating etc complete as directed by Engineer in charge.
Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.
Sec: 2.0 PCC & RCC works Providing material and labour for laying Autoclave Aerated Concrete Block chips/ bats cement concrete in 1:4:8 (1 Cement : 4 Coarse Sand : 8 graded Autoclave Aerated Concrete Block chips/ bats) for sunk filling grade including compacting, finishing, curing etc. complete as directed by engineer in charge.
Providing material and labour for laying Plain cement concrete M15 in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.
Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding (with 18 SWG -1.22 mm GI wire) and placing in position complete for all floors, all levels, all heights/ depth complete as per drawings, specifications and direction of Engineer in Charge.
Providing fusion bonded Epoxy coating not less than 175 micron thickness and upto 300 micron to reinforcement bars of any diameteer as per IS-13620-1993/ ASTM-775 M including testing of coating at plant and all taxes etc complete as directed by engineer ion charge.
Providing material and labour for laying in position Ready Mixed M-20 grade concrete/ batch mix concrete for reinforced cement conctere work, using cement content as per approved Design Mix without Fly Ash (Min cementitious level as per latest IS 456 shall be maintained) manufactured in fully automatic batching plant and transported to site of work in transit mixer for all lead having continuous agitated mixer, as per mix design for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying; cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability; finishing, compacting, vibrating, curing etc including cost of Form work but excluding the cost of reinforcement etc complete for all elements, all floors, any heights/depths, any lead and lift as directed by Engineer Incharge.
Providing material and labour for laying in position Ready Mixed M-25 grade concrete/ batch mix concrete for reinforced cement conctere work, using cement content as per approved Design Mix without Fly Ash (Min cementitious level as per latest IS 456 shall be maintained) manufactured in fully automatic batching plant and transported to site of work in transit mixer for all lead having continuous agitated mixer, as per mix design for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying; cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability; finishing, compacting, vibrating, curing etc including cost of Form work but excluding the cost of reinforcement etc complete for all elements, all floors, any heights/depths, any lead and lift as directed by Engineer Incharge.
Providing material and labour for laying in position Ready Mixed M-30 grade concrete/ batch mix concrete for reinforced cement conctere work, using cement content as per approved Design Mix without Fly Ash (Min cementitious level as per latest IS 456 shall be maintained) manufactured in fully automatic batching plant and transported to site of work in transit mixer for all lead having continuous agitated mixer, as per mix design for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying; cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability; finishing, compacting, vibrating, curing etc including cost of Form work but excluding the cost of reinforcement etc complete for all elements, all floors, any heights/depths, any lead and lift as directed by Engineer Incharge.
Providing material and labour for laying in position Ready Mixed M-35 grade concrete/ batch mix concrete for reinforced cement conctere work, using cement content as per approved Design Mix without Fly Ash (Min cementitious level as per latest IS 456 shall be maintained) manufactured in fully automatic batching plant and transported to site of work in transit mixer for all lead having continuous agitated mixer, as per mix design for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying; cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability; finishing, compacting, vibrating, curing etc including cost of Form work but excluding the cost of reinforcement etc complete for all elements, all floors, any heights/depths, any lead and lift as directed by Engineer Incharge.
Providing material and labour for fixing in expansion joint 100 / 150 / 200 mm thick SIL FLEX (Capcell HD 100) expansion joint board of best quality and approved make including cutting to required size and shape for all floors, all height etc complete as directed by Engineer In charge.
Providing material and labour for filling 25 mm thick joint with elastomeric joint sealant two component, high performance polysulfide formulation conforming to BS:4254 and ASTM C 920 having weathering resistance to ultra-violet rays and shall exhibit shore A hardness of 25 and have movement accommodation factor 25% including using of compatible primer of approved standard for at all floors, any lead and lift etc complete as directed by Engineer In charge.
Providing material and labour for fixing in position PVC pipe sleeves of 50mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge.
Providing material and labour for fixing in position PVC pipe sleeves of 75mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge.
Providing material and labour for fixing in position PVC pipe sleeves of 110mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge.
Providing material and labour for fixing in position PVC pipe sleeves of 160mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam before concreting. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while laying reinforcement and shuttering, sleeves shall not get displaced while concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Measurement shall be taken up to two decimal. (minimum 0.01 mt.). Rate shall be inclusive of removal of sleeves before water proofing or grouting. For all floors/ all levels/ all heights. Location of sleeve shall be approved by Engineer in charge.
Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) holes of 52mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge.
Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) holes of 77mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge.
Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) holes of 102mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge.
Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) holes of 152mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge.
Providing material and labour for wet drilling accurate and clean holes of specified diameter in RCC walls, slabs, beam or any other RCC member without vibration by core cutting (diamond drilling) holes of 202mm dia machine of approved make for laying service lines including scaffolding, safety majors, disposing the debris, cleaning, making good, providing epoxy mortar/ micro concrete/ patch repair mortar for concrete for grouting the gaps around the pipes for all levels/ all height, after approval of engineer in charge etc compete. Measurement shall be taken for the depth of holes in running meter for specified diameter. Holes shall made by authorized approved agency. Scanning of reinforcement shall be carried out before core cutting if required and as suggested by Engineer in charge. Location of core cutting shall be approved by Engineer in charge.
Providing material and labour for Cutting holes of required size in brick/ block masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.
Rebaring : Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical (medium duty) with the help of dispenser, into a hole of dia 8mm and depth 120mm as per manufacturer/ structural consultant's specification and fixing rebar of the required diameter subsequently. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item. Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge.
Rebaring : Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical (medium duty) with the help of dispenser, into a hole of dia 10mm and depth 150mm as per manufacturer/ structural consultant's specification and fixing rebar of the required diameter subsequently. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item. Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge.
Rebaring : Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical duty) with the help of dispenser, into a hole of dia 12mm and depth 180mm as per manufacturer/ structural consultant's specification and fixing rebar of the required diameter subsequently. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item. Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge.
Rebaring : Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical (medium duty) with the help of dispenser, into a hole of dia 16mm and depth 240mm as per manufacturer/ structural consultant's specification and fixing rebar of the required diameter subsequently. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item. Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge.
Providing and fixing of expansion/ seismic joint system for 100 /150 /200 mm wide expamsion joint gap of approved make related with floor location (floor to floor or floor to wall corner) with stone fixing arrangement (minimum 20mm recess depth for receiving stone) as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning/ self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical locations in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and match with finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates/ moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Rate shall be inclusive of edge preparation, moisture barrier, polyester powder coating (min 50 micron) on aluminum of approved shade and make if required. Cost of flooring stone/ tile shall be paid in relevant tender item. Expansion joint system shall be as approved for all floor all level including scaffolding etc complete.
Providing and fixing of expansion/ seismic joint system for 100 /150 /200 mm wide gap of approved make related with wall joint (internal wall to wall/ ceiling to ceiling/ wall to corner/ any angle) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning/ centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall or ceiling at corner/ ceiling application, with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multi cellular to facilitate movement. Expansion joint system shall be with all mandatory requirement as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Rate shall be inclusive of edge preparation, moisture barrier, polyester powder coating on aluminium of approved shade and make if required. Expansion joint system shall be as approved for all floor all level including scaffolding etc complete.
Providing and fixing of expansion/ seismic joint system for 100 /150 /200 mm wide gap of approved make related with External wall joint location (wall to wall/ wall to corner) as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning/ centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall or ceiling at corner/ ceiling application, with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multi cellular to facilitate movement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Rate shall be inclusive of edge preparation, moisture barrier, polyester powder coating on aluminium of approved shade and make if required. Expansion joint system shall be as approved for all floor all level including scaffolding etc complete.
Providing material and labour for fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut Powder coated aluminium sheet approximate 2.5mm thick (minimumthickness of powder coating 50 micron) and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia and 75 mm long bolt including providing aluminium washers 2 mm thick & 15 mm dia, at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete as per direction of Engineer-in-charge.
Sec.3.0 Centering & Form works Providing material and labour for formwork for exposed concrete surfaces (Only extra addition cost on normal shutering) (vertical or horizontal surface) in smooth finish, desired pattern and size as per drawing and specifications, including rendering with white cement and grey cement, using laminated shuttering plywood, for vertical and steel or laminated plywood shuttering for horizontal surfaces for all types RCC elements like slabs, walls, columns, beams, folded staircase (all sides), sill, coping, lintels, jambs, beam hunching, vertical fins, pardi etc. including neat cleaning the exposed concrete surface, as directed by the engineer-in-charge. In case of round window opening in exposed RCC wall, for payment of expose shuttering opening cutout shall not be deducted (both side). Rate shall be applicable for all floors, all levels, all places and all shapes. The contractor shall submit shuttering pattern including tie-rod hole position based on architectural conceptual drawings. (Same kind of shuttering material should be only used for standard and residual sizes.) Tie-rod hole shall be filled with polymer mortar/ polymer concrete as per manufacturer's specification.
Extra for additional height of propping and centering where the height of propping and centering exceeds 4.0 mt. Between supporting floor two ceiling including temporary brick or stone pillars for supporting as required. (I) Height more than 4.0 mt & upto 5.0 mt.
Extra for additional height of propping and centering where the height of propping and centering exceeds 4.0 mt. Between supporting floor two ceiling including temporary brick or stone pillars for supporting as required. (I) Height more than 5.0 mt & upto 9.0 mt.
Extra for additional height of propping and centering where the height of propping and centering exceeds 4.0 mt. Between supporting floor two ceiling including temporary brick or stone pillars for supporting as required. (I) Height more than 9.0 mt & upto 13.50 mt.
Sec.4.0 Masonry works Providing material and labour for laying Brick work using common burnt clay building Conventional bricks having crushing strength not less than 35 kg/SqCm in foundation and plinth in Cement Mortar 1:5 (1- Cement : 5 -fine sand) in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
Providing material and labour for laying Brick work using common burnt clay building Conventional bricks having crushing strength not less than 35 kg/SqCm in Cement Mortar 1:5 (1- Cement : 5 -fine sand) in superstructure above plinth level for all Floor in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
Providing material and labour for laying Half brick masonry in common brunt clay building Conventional bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in superstructure for all Floor in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.
Providing material and labour for laying of hollow concrete fair finish block masonry for jali work madeout from M20 grade average 200mm thick hollow block of different size to cerate a pattern as per drawing confirming to IS 2185 Part I grade A (7.0), shape of hollow part shall be round, square or rectangle. Jali wall shall be constructed in Polymer (consumption as per manufacturer's specification) added cement mortar 1:2 (1 cement : 2 coarse sand) by providing 2 no of 6 mm dia. GI bar at each layer vertically as well as horizontally. GI wire/ rod shall be anchored in adjoining surface with quick fix chemical including roughening, cleaning, fixing and finishing/ rendering in grey and white cement sand mortar 1:1 in the line and level and in pattern, provision of groove as per drawing, curing at all heights, all floors with necessary scaffolding etc complete as per the drawing and direction of Engineer in charge. Contractor shall prepare mock up for one panel with approved block and as per satisfactiobn of Architect. Note: Payment should as per actual area of jali made out of hollow block, no deduction of hollow gap of block should be considered for payment.
Providing material and labour for fixing 190mm x 190 mm x 80 mm glass bricks of approved make and design with white CM 1:2 ( 1 white cement : 2 sand). Two numbers of 5 mm thick GI wires to be passed through PVC spacers in each joint horizontal as well as vertical by drilling holes in surrounding surface (brick or RCC) and filling the same with Hilti or equivalent chemical (rebarring). The PVC concealed spacer (with provision for passing the 2 no. GI wires in horizontal and vertical direction) shall be provided to maintain grooves/spaces for GI wire and white cement mortar at the junction of two glass bricks including curing. The sample of the glass brick shall be got approved by Architect. The glass bricks shall be fixed with placing GI wires vertically as well as horizontally after passing through the spacer and having minimum lap length of + 200 mm as per the site conditions at all the places, all heights, all level and in all shapes, etc. complete, as per drawing and as directed by Engineer-in-charge. Joints along the periphery of glass bricks shall be filled with approved make and color weather silicone sealant of DOW corning 789 or equivalent.
SEC:5 Doors and Windows work ALUMINIUM WORKS - Providing material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required. and excluding the cost of necessary hardware and Glazing or Infill material.
Fix Louvers and Fins (made out of Aluminium Section) Providing, fixing, designing aluminium fixed louver of any type of louver section of approved make having minimum 50 micron polyster powder coating on all the surfaces of approved shade, texture & make as per manufacturer's specifications. Contractor shall submit the shop drawing for louver/ fins based on concept design/ drawing and as per elevation. Aluminium louver section shall be fixed on aluminium framing/ carrier/ panel/ GI clip and necessary sub structure with required fastners, hardware as per approved shop drawing etc complete for all floor, all height including scaffolding as directed by engineer in charge. Louver, framing and sub structure shall be in proper line, level and plumb. Necessary MS work shall be paid in relevant tender item.
Openable Louvers Providing and fixing aluminium operable system louvers of 50 micron Pure Polyester Powder Coating of approved shade & colour and texture manufactured by Techanal, Domal, or equivalent with operating mechanism frame louver with gasket and piles. The corner joints of the frame shall be made at 45 degree using die-cast solid aluminium corner cleats fixed with external byttins with a spring for rapid and secure joint assembly. Gaskets shall be of EPDM material. Work shall be carried out in the existing door / window frame as per sample approved by Architect / EIC. Operating panel should be provided as per drawing. Actual measurement of system with louvers shall be measured and paid in sqmt. Rate should be inclusive of aluminium sub frame for housing operating system.
Glass Louvers Ventilation Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm (Jindal Section:2434, @Wt.0.643Kg/mt) or euivalant with colour Powder Coated alluminium frame for ventilation with 5mm thick frosted glass as details etc complete for Ventilation
Providing material and labour for fixing 6mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.
Providing material and labour for fixing 8mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.
Providing material and labour for fixing 10mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.
Providing material and labour for fixing 12mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.
Providing material and labour for fixing 6mm thick Wired Glass of any size, any shape in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing with EPDM quality rubber/ silicon sealant/ structural sealant on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Architect. Actual installed quantity shall be measured and paid. Rate shall be inclusive of all type of wastage.
Providing material and labour for fixing 6mm thick Compact Sheet of any size, any shape, any color (single side, double side coloured), any texture of approved make and as per approved sample (approved by architect). Compact sheet shall be fixed in aluminium frame and shutter work with necessary cutting of sheet, provision of groove, filling of groove (both side) as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ adhesive tape/ screwing on the periphery of the sheet as per the required thickness etc. complete at all floors/ all levels/ all heights as per the drawing & directed by Engineer in charge. Cut edges of the compact sheet shall be provided with masking tape. Actual installed quantity shall be measured and paid.
Providing material and labour for fixing in position SS 304 - 18 x 16 mesh and 32gauge Mosquito net of any size any shape having 50 micron pure polyster powder coating of approved make and shade for aluminium sliding shutter/ fixed shutter or in front of aluminium louvers as per approved shop drawing prepared by contractor. Jali shall be fixed with SS304 grade screws and fasteners required to tighten the Jali/ Net including fxing channel, EPDM quality rubber/ silicon sealant etc complete for all floors, all levels, all heights as directed by engineer in charge. Only installed area of mosquito net shall be measured and paid in Sqm without considering any westage. All aluminium sections shall be paid under relevant tender item.
Providing material and labour for fixing factory made and pressed laminated 35mm thick flush door shutter of specificied thickness made of ISI marked non decorative type flush door shutters confirming to IS- 2202 (Part 1), core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers (IS 710 Grade) on both faces of shutters having 1 mm thick decorative type laminates of approved make, shade, finish on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhesive conforming to IS 848 including providing and fixing external lipping with 2nd class teak wood battens, exposed (37mm x 12mm)/ concealed (35mm x 12mm) on all edges of door shutter as required with 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ lacquer polishing with primer to all exposed side of lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items. Cost of laminates shall be paid in relevant tender item.
Providing material and labour for fixing factory made and pressed laminated 30mm thick flush door shutter of specificied thickness made of ISI marked non decorative type flush door shutters confirming to IS- 2202 (Part 1), core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers (IS 710 Grade) on both faces of shutters having 1 mm thick decorative type laminates of approved make, shade, finish on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhesive conforming to IS 848 including providing and fixing external lipping with 2nd class teak wood battens, exposed (37mm x 12mm)/ concealed (35mm x 12mm) on all edges of door shutter as required with 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ lacquer polishing with primer to all exposed side of lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items. Cost of laminates shall be paid in relevant tender item.
Providing material and labour for fixing 1 mm thick Laminate sheet of any size, any shape, any color, any texture of approved make and as per approved sample (approved by architect) on Non decorative flush door, panelling work, fixed partition, any ply surface etc with necessary nails, screws, adhesives as per drawings and as per approved sample. The rate shall be for all heights, all floors, all places etc complete as directed by engineer in charge. Actual laid area shall be measured and paid without considering any westage. Laminates and ply shall be factory pressed.
Providing material and labour for fixing vision panel made out of 5mm thick clear toughen glass of any shape any size in all type/ thickness of flush doors shutter. Glass shall be fixed with teak wood lipping (Lacquer polished of approved make and shade) on both side the door of required size as shown in drawing and direction of Engineer-In-Charge. Rate shall be includes the cost of cutting door, provision of glass with both side polished lipping, making good etc complete. The actual installed area of vision panel shall be measured for payment.
Providing material and labour for fixing 6mm thick frame less mirror of approve make in any shape and sizes as per drawing. Mirror shall be fixed on 6mm thick cement bonded particle board (Bison panel) backing. Cement bonded particle board shall be fixed to wall with approved SS 304 fastener. All edges of glass shall be grinded (as required), cute corner and polished. Glass shall be fixed with silicon sealant/ 3M tape etc complete at all floors/ all levels/ all heights as directed by engineer in charge. Installed area of mirror shall be considered for payment without wastage.
Providing material and labour for Extra charges for machined Perforation of required dia and pattern in flush door shutter/ compact sheet of any thickness for air circulation for all floor, all height all level as per drawing and as directed by Engineer in charge. Edges of perforation shall be finished and sharpen.
Notes for Hardware : Supplying and fixing heavy quality fixtures and fittings for doors, windows, ventilators, partition wall, cabinets with necessary screws, nails, machine pins etc at all floor/ all levels/ all heights complete. Sample shall be approved by Architect before execution. As per description, SS hardware shall be of 304 grade or 316 grade as per item description and as per approved sample. The fixture & fastenings shall be provided as under : Providing material and labour for fixing single/ double action hydraulic floor spring with SS cover plate & adjustable concealed casted top pivot (two piece) and bottom strap of approved make for wooden/ aluminium doors of specified capacity with minimum one year guarantee. Rate shall be inclusive of cutting of floor neatly, grouting the floor spring & cleaning/ polishing the floor & maintaining in good working condition until defect liability period. In case of Aluminium shutter bottom arm of floor spring & top pivot shall be firmly fixed in the aluminium members using required size of teak wood by making rabbet in the wood. The Floor Spring shall conform to EN 1154. a) Hold open having for shutter width upto 1200mm with standard spindle and cover plate. Closing force complying with EN 1154 2-4
Providing & Fixing heavy quality SS 304 heavy pivot top & bottom (pair) of approved make with SS screws ect complete as directed by engineer in charge.
Providing material and labour for fixing hydraulic rack and pinion door closer with standard arm (Silver finish) with screws to pivoted/ hinged door of approved make for specified door width with minimum one year guarantee. All adjustment screws face fixed. Rate shall be inclusive of fixing with using the template as per manufacturer’s specification & maintain in good working condition until defect liability period. The door closer shall conform to EN 1154 standard. a) with standard/ hold open arm with two independent closing valves and latching speed adjustable by arm without mounting back plate, Closing force complying with EN 1154 2 - 4 for up to 900 mm door shutter width
Providing material and labour for fixing SS 316 grade butt hinge of average 100 x 75 x 3 mm - with ball bearing of approved make as per approved sample with necessary screws etc. complete for all floor all height all level as directed by Engineer in Charge.
Providing material and labour for fixing SS 316 grade butt hinge of average 100 x 64 x 2.5 mm - without ball bearing of approved make as per approved sample with necessary screws etc. complete for all floor all height all level as directed by Engineer in Charge.
Providing material and labour for fixing set of dead lock of approved make with 50mm backseat, 20mm square for end with 72 mm centers including strike plate in satin stainless steel finish as per DIN 18251-1, grade 2 and prepared for euro profile cylinder (EPC) including strike plate and EPC length 60/70 mm standard Euro profile Pin Cylinder/ Half pin cylinder with both side key/ one side key one side knob operation with one pair of SS 316 grade Escutcheons (key hole plate) for wooden/ aluminium/ metal doors with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.
Providing material and labour for fixing SS 304 satin finished set of narrow style dead lock of approved make with 25mm /35 mm set back necessary euro profile pin cylindrical lock 60/ 70 mm for Key and or knob operation and one pair of SS 316 grade Escutcheons (key hole plate) for aluminium door with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.
Providing material and labour for fixing Mortise lock of approved make having 72mm centre to centre, 55mm Backset 20mm Square forend and 60/ 70mm standard Europrofile Pin Cylinder with both side key /one side key - one side knob operation and SS 316 grade hollow tubular pipe pair of Mortise handle of 22mm dia 150mm long with a pair of SS 304 Escutcheons (key hole plate) for wooden /aluminium/ metal doors with necessary ss phillips head screws etc complete for all floor, all height, all level as per approved sample as directed by engineern in charge. The lock shall be with 3 keys.
Providing and fixing Electronic Door Lock of approved make for wooden door having thickness of 35 to 50 mm of following specifications. 1) Dead Latch Lock Type with 30 RFID Cards and 78 Pin Codes 2) 2 keys for mechanical over ride function 3) Shall have dimensions of Front Body 37.97 (D) X 70 (W) X 170 (H) mm and Back Body 25.48 (D) X 70 (W) X 179 (H) mm 4) low battery indicator and emergency power supply 5) anti panic egress function from inside Contractor Shall provide 1 year manufacturer’s warranty against material and workmanship. Rate shall be inclusive of lock, nesscry fixing hardwarer, cutting of wooden door shutter, making good etc complete as directed by engineer in charge
Providing material and labour for fixing Mortise shaft dead bolt of approved make with key (Alen Key lock), sleeve with 57mm backset and 25mm square forend in stainless steel satin finish etc complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing Zinc material indicator bolt of approved make for toilet door with Thumb Turn inside & Emergency Release & Indicator Outside with necessary screws etc complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 200 mm long x 19mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.
Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 300 mm long x 22 mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.
Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 600 mm long x 32 mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.
Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 1200 mm long (out to out) x 38 mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.
Providing material and labour for fixing SS 316 grade handles 150mm long D shape hollow tube handle of approved make with both end bracket with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing 25mm diameter (1.5mm thick) SS 316 satin (brush) finish Disabled Grab Rails/ handle of 600mm long of approved make with necessary SS 304 grade screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing of SS 304 grade brush finish 450mm height Tower bolt (barrel type with minimum rod size shall be 10mm) of approved make in wooden doors/ aluminium doors/ metal doors with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing of SS 304 grade brush finish 250mm height Tower bolt (barrel type with minimum rod size shall be 10mm) of approved make in wooden doors/ aluminium doors/ metal doors with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing of SS 304 grade satin finish lever action Flush tower bolt with 19mm projecting bolt (extended rod of 600mm length) aluminum casted of approved make for double shutters aluminum door, with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Aldrops of 16 mm dia x 250 mm including 3 nos. fixing Bracket and 1 no. locking bracket of approved make with necessary MS nickle Plating Bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Tadi of 12mm dia x 200mm including 3 nos.fixing Bracket of approved make with necessary screws, pins, bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for Fixing Zinc material satin finish 85 to 100mm long Baby Latch with necessary SS Screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing SS 304 brush finish solid Door Stopper with magnet, fixed type, wall mounted (square/ round) of approved make with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing SS 304 grade brush finish solid Door bufer with pvc base, wall mounted (square/ round) of approved make with necessary screws etc. complete as approved by Engineer-in-charge in Charge.
Providing material and labour for fixing Aluminium powder coated butt hinges of required capacity of approved make for casement window/ door (europrofile) with necessary accessories, screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing SS 304 adjustable friction windows stays of size 355 X 19 mm of approved make with necessary stainless steel screws to the side hung or top hung windows etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing and fixing powder coated single point lock with mortise handle (without lock) of approved make with heavy gear mechanism of required capacity including all required accessories like handle, fork, connector, extensior, polyamide, locking point, corner transmission and striker etc as per approved manufacturer recomendatation for aluminium casement door and window (top hung or side hung) with necessary screws etc complete as directed by engineer in charge.
Providing material and labour for fixing powder coated two point lock with mortise handle (without lock) of approved make with heavy gear mechanism of required capacity including all required accessories like handle, fork, connector, extensior, polyamide, locking point, corner transmission and striker etc as per approved manufacturer recomendatation for aluminium casement door and window (top hung or side hung) with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing powder coated inbuilt flush handle (without lock) of approved make of required capacity including all required accessories like nib, counter plate etc as per approved manufacturer recomendatation for aluminium sliding window with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing powder coated multi point lock with mortise handle (without lock) of approved make of required capacity with heavy gear mechanism including all required accessories like nib, nib holder, counter plate, fork, pawl, polyamide strip, dummy handle etc as per approved manufacturer recomendatation for aluminium sliding doors and window with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing adjustable/ fixed Teflon roller bearing set with reinforced nylon casing of approved make (twin or single wheel according to weight and size) for sliding window/door as per drawing etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.
Providing material and labour for fixing of Hollow metal fire rated doors of approved make and shade as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI against Test Schedule Ref No FR/0490 or ARAI for maximum rating of 2hrs with vision panel. Test certificates should be available for vision lites /panels as part of the fire door assembly. Independent glass test certificates will not be accepted. Manufacturer test certificate shall cover doors both single & double leaf doors and Hardware should pass European certificate "CE" of conformity / UL with required fire ratings. Any deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer subject to architect’s approval and should be ISO Certified company. Providing material and labour for fixing Fire rated Door frame shall be double rebate profile of size 143 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet. Frames shall be Mitered and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb. Frames should be provided with back plate bracket and SS 304 anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening. Frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250 hours of salt spray test as per the directions of Engineer - in- charge. Rate shall be inclusive of anchore fastner and rubber silencer for all floor all level but excluding of SS ball bearing hinges).
Providing material and labour for fixing Fire rated Door shutter shall be 46mm thick fully flush double skin door with or without vision lite. Door shutter shall be manufactured from 1.2mm (18guage) minimum thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a beading and screws from inside. EPDM open cell sponge seal and bottom seal shall be provided at periphery and bottom of shutter as per manufacturer's specificatipon. Door shutter shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250 hours of salt spray test as per the directions of Engineer - in- charge. Rate shall be inclusive of all type seal for all floor all level but excluding of vision panel and all type of hardware.
Providing material and labour for fixing fixed vision panel glass in fire rated door as per manufacturers recommendation with a G.I. beading, & special ceramic tape/ gasket of approved make etc complete for all floor all height as directed by engineer in charge. The glass should be 6mm clear borosilicate fire rated glass of 2 hour rating.(Actual installed glass size (with two decimal) to be measured for payments).
Providing material and labour for fixing 120 min fire rated SS 304 Ball Bearing Butt Hinges 100mm x 75mm x 3 mm CE marked for fire rated metal door of approved make with necessary screws etc. complete as recommended by manufacturer for all floor all height and as directed by Engineer in Charge.
Providing material and labour for fixing Fire rated (120 minutes) Rack and pinion non-handed door closer of approved make EN size 2-4, with back check and standard arm with two independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed with slide plate. The door closer shall be with Silver finish cover. The door closer shall conform to EN 1154 standards and CE marked with necessary fittings etc. complete for all floor, all height as recommended by manufacturer and as directed by Engineer in Charge.
Providing and fixing 120 min fire rated Mortise sash lock of Dorma 281a or equivalent with 70 mm Cylinder Thumb turn with Lever TH 126 CE marked for fire rated metal door of Dorma or equivalent with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer in Charge.
Providing material and labour for fixing 1 point panic device in Contur design, carry bar for single door for fire and smoke check doors, with steel latch, security anti thrust latch for door widths upto 1300mm, consisting of 2102F, 2105 in silver finish of approved make. As per EN 1125, CE marked etc. complete for all floor, all height as recommended by manufacturer and as directed by Engineer in Charge.
Providing material and labour for fixing 1 point panic device in Contur design on active leaf and 2 point modular on inactive leaf, carry bar for rebated double door of approved make for fire and smoke check doors, with steel latch, security anti thrust latch consisting of all required accessories in silver finish. As per EN 1125, CE marked with necessary fittings etc. complete for all floor all height as recommended by manufacturer and as directed by Engineer in Charge.
Providing material and labour for fixing External trim with design lever handle of approved make suiting the panic bar for fire and smoke check doors for max. 60mm thick door prepared for half euro profile cylinder and in Silver finish with necessary fittings etc. complete for all floor all height as recommended by manufacturer and as directed by Engineer in Charge.
Providing and fixing of Non Fire rated Hollow metal door of approved make and shade at all levels from ISO 9001-2000 certified Manufacturer. All hollow metal general doors with or without vision panel. Pressed Galvanized steel Single /Double leaf to required sizes of approved make which consists of frame, shutter, infill and finish as detailed below and conforming to IS 277. Door frame shall be Double rebate profile of size 143 x 57 mm made out of 1.20mm thick galvanized steel sheet (18 gauge). Frames should be Mitered and field assembled with self tabs. Frames should be fixed with back plate bracket and anchor fasteners of approved size and make for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement slurry if recommended on the clear masonary opening. Door leaf should be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 0.8mm (22 gauge) minimum thick galvanized steel sheet. The internal construction of the door should be rigid with steel stiffeners/ pads and reinforcement. The infill material shall be resin bonded honeycomb core. All doors should be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be as per joinery details with a screw on glass beading on the inside. The glass should be 5mm clear toughened glass. Shutter shall be fixed to frame with SS 304 Ball Bearing Butt Hinges of size 100mm x 75mm x 3 mm (no of hinge as suggested by engineer in charge). All door shutter and frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 250 hours of salt spray test. Rate shall be include supply and installation of door i.e frame, anchor fastener, shutter with vision lite, hinge but exclude the cost of hardware (other than hinge) etc complete as directed by engineer in charge. Out to out area of door with frame shall be measured for payment.
Providing material and labour for process charges of Frosting the glass (any thickness of glass) as per drawing and as directed by engineer in charge. Rate shall be for only for extra cost of Forsting on Glass for all floor, all height all level.
Providing material and labour for fixing of 12 mm thick approved quality soft board of approved make with cotton cloth/fabric of approved make and shade on 12mm thick BWR 300 grade ply with 1st class teak wood beading all around including lacquer polish, as approved sample and as directed by Architect. Elevation area of the soft board including lipping shall be measured and paid. The rates shall be inclusive of all wastages, laquer polishing, fabric, labor for applying fabric, for all level, all heights etc. complete as directed by Engineer-in-charge. Wastage shall not be considered. Contractor shall get the sample and approved by Architect/ Engineer-in-charges.
Frosting Film Providing, Supplying, Installing of Frosting film of approved make and pattern on glass (any thickness of glass) as per drawing and as directed by engineer in charge. Rate shall be for only for extra cost of Forsting on Glass for all floor, all height all level.
Sec.7.0 Plastering & Pointing works Providing material and labour for laying 10mm thick mala cement plaster in single coat on ceiling & stairs and soffits plastering and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) for all floor, all level, all height (including all basement) with necessary scaffolding, curing, finishing, making grooves, forming pattas, hacking properly to RCC surface etc. complete as directed by the Engineer-in-charge.
Providing material and labour for laying 15mm to 18mm thick cement plaster in single coat on sides of brick work/ blocks wall/ RCC work for interior plastering and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) for for all floor, all level, all height (including all basement) with necessary scaffolding, curing, finishing, making grooves, forming pattas, hacking properly to RCC surface etc. complete as directed by the Engineer-in-charge.
Providing material and labour for laying 20 mm thick internal/ external double coat mala cement plaster on interior brick / concrete work for plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse sand) finished for all floor, all level, all height (including all basement) with necessary scaffolding, curing, finishing, making grooves, forming pattas, hacking properly to RCC surface etc. complete as directed by the Engineer-in-charge.
Providing material and labour for laying 20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) with necessary scaffolding, curing, finishing, making grooves, forming pattas, hacking properly to RCC surface etc. complete as directed by the Engineer-in-charge.
Providing material and labour for fixing G.I. hexagonal chickenmesh of size 20mm x 20mm of 22 gauge at junction of concrete and brick work or between different materials after making "V" grove between two different material surface and filled with rich cement mortar and @ 100mm on each side of surfaces including necessary "U" nails/ screws/ washers with cleats for fixing, overlaps, curing, scaffolding etc complete for all floors/ all levels/ all heights/ all shapes as per direction of Engineer-in-charge.
Sec.8.0 Waterproofing works Providing material and labour for laying average 18mm thick double coat (water proof) smooth/ wired finish cement plaster on sides of masonry work/ block wall/ RCC wall, 12 mm thk first coat in CM 1:3 (1 cement : 3 coarse sand) by spraying , second coat of 6 mm of CM 1:3 (1 cement : 3 fine sand) and mixing Integral waterproofing liquid admixture for mortar in recommended proportions in both coats, finishing the surface wired finish/ smooth finish with a floating coat of neat cement slurry at 2.75 Kg/ sqm to receive the tiles for all floors, all shapes and all height including hacking to RCC surface, scaffolding, curing etc. complete for all floor, all height as directed by engineer-in-charge. Cement slurry admixed with Integral waterproofing liquid admixture for mortar in recommended proportions is to be applied before each coat and final finishing coat.
Providing material and labour for laying average 50 mm thick IPS, water proof cement concrete flooring in 1:2:4 (1 Cement : 2 Sand : 4 Graded Aggregate 10mm Nominal size) to RCC under ground tanks at all heights in line, level and gradient including mixing water proofing compound in recommended proportions suggested by manufacturer as approved by Engineer-in-charge and leaving the surface rough wired finish to receive any type of flooring / smooth finish etc complete for all floor all height as directed by engineer in charge.
Providing material and labour for laying integral cement based water proofing treatment (India type brick bat) including preparation of surface as required for treatment of roofs, balconies, terraces etc with average thickness of 120 mm and minimum thickness at khurra as 65 mm and consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with wired finish to receive china mosaic flooring. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge for all height all level.
Toilet waterproofing Providing material and labour for carrying out waterproofing treatment to sound concrete surface of toilets, sunken slabs, corridors, wet areas etc. after proper surface preparation to remove loose dust, dirt etc., repairing of cracks (if any) using polymer modified mortar, carry out cementitious injection grouting at leakage points modified with Plasticized Expandive Grout Admixture @ 225 gms per bag of cement, carry out 50 mm thick cement mortar (1:3) vatta/ corner modified with Styrene Butadine Polymer bonding agentat dosage of 2.5 Ltr per 50kg cement, Pre-dampening concrete surface, mixing and application of two coats of Elastomeric Polymer modified cementitious waterproofing coating by incorporating alkali resistance 45 gsm glass fibremesh between 1st and 2nd coat using suitable brush or roller as per coverage etc. complete for all floor al height all level as per manufacturer’s specification and as directed by engineer in charge. Cured Polymer modified cementitious waterproofing coating shall comply with ASTM D4060, ASTM D4541, ASTM D638,ASTM C836 and possess below properties: Mixed density : 1.68 g/cc, Adhesion to concrete-> 1 N/mm2, Non-toxic, Static crack accommodation-1 mm Water proofing system shall be executed by only approved applicator of approved brand and under strictly supervision of technical fellow of manufacturer. The rate includes giving 10 year guarantee for waterproofing on a Rs.100/- stamp paper in approved proforma.
Hole Packing treatment on service line Providing material and labour for applying total packing treatment on any type of pipes comes into water proofing area for all floor, all height as directed by engineer in charge as follows : Preparing the inside surface of core and Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Applying a coat of styrene- butadiene based polymer coating using Styrene Butadine Polymer bonding agentto enhance adhesion between the packing material and other surfaces. Packing the gap using non shrink cement polymer based grout using Non-shrink cementitious grout upto the surface of the bore whilst the bonding agent is in tacky state before application of water proofing treatment. Treatment shall be executed by same agency with same manufacturer's product. Warranty includes in water proofing item.
Providing material and labour for applying hydrophilic crystalline based waterproofing for concrete walls, raft (basement and under ground water tank) with system In two coat application. The application to be done from + ve (positive) side on a wet open pore green concrete surface at coverage of 0.8 to 1 Kg/Smt as per manufacturer specification. It should be hydrophilic in nature, should be able to grow crystals year after year to seal microcracks.The product should confirm to DIN 1048 part 5 and should provide in depth crystallization. The product technology should be CPWD and EIL approved. Application should be done on wet surface after 3-6 hours of casting of concrete. The material and application warranty to be given by manufacturer’s authorized distributor/ applicator on prescribed format. Rate shall be inclusive of construction joint treatment, crack repair, patch repair, grouting, including cost of scafolding for all height all level as directed by engineer in charge.
Providing material and labour for applying of Swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure, such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge for all floor, all height all level. The product performance shall carry guaranteed for 10 years against any leakage.
Providing and applying 400 microns thick coal tar extended epoxy resin coating to sound concrete surface after carry out surface preparation to remove loose concrete, curing compound or any other foreign material, mixing base and hardener component of Coal tar extended epoxy resin coating, apply first coat at 200 microns DFT using suitable brush or roller, allow the first coat to dry for 6 hrs at 35°C followed by application of application of second coat at 200 microns DFT in perpendicular direction to first coat etc. complete as per manufacturer’s specification for all level all depth as directed by engineer incharge. Coal tar extended epoxy resin coating shall be having 100% solid contents by weight, specific gravity - 1.54 at 27°C, Curing efficiency – 93 % (BS 7542), Water absorption <0.01 % (ASTM D 570), Bond Strength: min 1 N/mm2 (BS 1881 Pt 207), Water Permeability: nil at @ 2 bars pressure over 3 months, Salt spray test: nil @ 200 microns DFT over 1000 hrs (BS 1881 Pt. 124:1988), Impact Resistance: passed (BS 3900 Pt E3) & Chemical resistance checked in accordance with ASTM D 453
Providing and mixing Migratory Corrosion Admixture POLYALK CP 293 having Specific Gravity 1.01 to 1.04, pH value (Minimum 9.50) shall be alkaline in nature and having bipolar concrete penetrating corrosion inhibiting properties, inhabitor shall be non-nitrite based & have the ability to provide corrosion protection to both anodic and cathodic sites on the steel surface, inhibitor-steel complex shall formed polydentate complexes, having more than one bond with steel per molecule of inhibitor, with steel surface to promote proper film formation with enhenced bond to steel, inhibiting the electro-chemical corrosion reaction, inhibitor shall not have any adverse effect on concrete compressive strength, inhibitor shall have a corrosion rate of zero coulombs per ASTM-G109-2005, admixture shall be conforming to IS 9103 and in liquid form at the rate of 3Kg per one cubic meter volume of concrete admixture shall be added to the water, during mixing of cement, sand & aggregates and at the same rate admixture shall be added in case of Ready Mix Concrete at plant site, mixing of admixture during mixing of cement, sand and aggregates OR at work site the admixture shall be added in Concrete Transit Mixer before pumping / placing of concrete etc. complete.
Sec.9.0 Flooring works Providing material and labour for laying Ceramic tiles 6mm thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) and fixed with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Sample and mockup shall be approvd before procurement of material.
Providing material and labour for laying Ceramic tiles 6mm thick in skrting, risers of steps and dedo laid on plastered wall with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Sample and mockup shall be approved before procurement of material.
Providing material and labour for laying average 25mm thick machine cut semi mirror polished Green Kota stone slab of size upto 600mm in flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including curing, rubbing and polishing at all floors any heights, any lead and lift in any shape and pattern etc complete as directed by Engineer In charge. Sample shall be approved before execution. Kota stone shall be in uniform shade of reuired size. Sample and mockup shall be approved before procurement of material.
Providing material and labour for laying 8 to 10 mm thick Kota stone slabs in upto 100mm high skirting, (flush with plaster) laid on average 10 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including providing 10mm wide grove between skirting and plaster, rubbing and polishing complete as directed by Engineer In charge. Sample shall be approved before execution. Kota stone shall be in uniform shade of reuired size. Sample and mockup shall be approvd procurement of material. Shade of skirting must be match with flooring stone.
Providing material and labour for laying average 40 mm thick machine cut polished Green kota stone slab of size upto 0.9mt length with uniform thickness double side polished at edges for parapeet wall coping, window sills, over 20 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry or stone fixing adhesive and mechanical fastner of approved make including rounding of exposed edges, polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. All Expose edges of stone shall be pencil sharped and in even thickness and polished at all floors any heights, any lead and lift etc complete. as directed by Engineer Incharge. Sample shall be approved before execution. Sample and mockup shall be approvd procurement of material.
Providing material and labour for laying average 25 mm thick machine cut polished Green kota stone slab of size upto 2.1mt length with uniform thickness for tread, window jambs & sills, coping over 20 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with gray cement slurry including pencil sharped exposed edges, polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. All Expose edges of stone shall be pencil sharped and in even thickness and polished at all floors any heights, any lead and lift etc complete. as directed by Engineer Incharge. Sample and mockup shall be approvd before procurement of material.
Providing material and labour for laying average 25 mm thick machine cut polished Green kota stone slab of size upto 2.1mt length for riser of stair over 12 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with gray cement slurry including polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. The rate shall be inclusive of making rebates of 10x10mm for forming the grooves between treads and risers with polishing inside the groove. Sample shall be approved before execution. Sample and mockup shall be approvd procurement of material.
Providing material and labour for laying average 30 mm thick machine cut both side polished Green kota stone slab of size upto 1.5mt length for shelves, counter, partition in walls, self, etc as per drawing of stair over 12 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with gray cement slurry including polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. The rate shall be inclusive of making rebates of 10x10mm for forming the grooves between treads and risers with polishing inside the groove. Sample shall be approved before execution. Sample and mockup shall be approvd procurement of material.
Providing material and labour for laying cement concrete pavement (of any thickness) with 1:2:4 (1-cement : 2-coarse sand : 4-stone aggregate 20mm nominal size) including curing, finishing with floating coat of neat cement complete at all floors any heights, any lead and lift etc complete. as directed by Engineer Incharge.
Providing material and labour for laying 8 to 10mm thick full body vitrified tile of size upto 600mm of any shade, any finish (glossy, matt, satin or anti skid finsh) of approved make in flooring and Skirting laid over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) and fixed with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including provision of groove, grouting of joints, finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Grouting shall be paid in relevant tender item. Sample and mockup shall be approvd procurement of material. Actual laid area of tile shall be measured and paid.
Providing material and labour for laying 8 to 10mm thick, double charged Vitrified tiles of size upto 600mm (of any shade glossy, matt or satin finsh) of approved make, shade and finish as approved by Architect/ EIC for all floors/ any height/ any levels etc in wall tile, dado, risers of steps, jambs as per drawings. Wall tile is to be fixed over 10 to 12 mm thick smooth finish plaster in cement mortar 1:3 (1 cement : 3 coarse sand) and fixed with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including provision of groove, grouting of joints, finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Grouting and backing coat plaster shall be paid in relevant tender item. Sample and mockup shall be approvd procurement of material.
Extra for providing material and labour for Grouting the joints of any type of flooring tiles of Size upto 600mm having joints of 3mm / 4mm width and in full depth, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade and approved make (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.
Providing material and labour for laying approved quality average 18mm thick mirror polished Granite stone of approved shade in floor, otta in any pattern etc size upto 600mm including average 20 mm thick cement mortar bedding in 1:6 laid and jointed with white cement and matching pigment including rubbing, re-polishing after fixing to remove any undulation between the joints (if required) with different grades of Emery, refilling of open joints, curing, daily cleaning and mopping, as per satisfaction of Architect and as directed by Engineer in charge at all floors/ all levels/ all heights and all shapes. (Only finished work will be measured.) Sample and mockup shall be approvd procurement of material.
Providing material and labour for laying approved quality average 18mm thick mirror polished Granite stone of approved shade in floor, otta in any pattern etc sizes upto 1200mm including average 20 mm thick cement mortar bedding in 1:6 laid and jointed with white cement and matching pigment including rubbing, re-polishing after fixing to remove any undulation between the joints (if required) with different grades of Emery, refilling of open joints, curing, daily cleaning and mopping, as per satisfaction of Architect and as directed by Engineer in charge at all floors/ all levels/ all heights and all shapes. (Only finished work will be measured.) Sample and mockup shall be approvd procurement of material.
Providing material and labour for laying 8 to 10 mm thick machine cut polished Granite stone slabs of same shade as flooring and as per approved sample in skirting upto 100 mm high as per drawing (flush with plaster) laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including providing 10mm wide grove between skirting and plaster, rubbing and finishing complete. Shade of skirting must be match with flooring stone.
Providing material and labour for laying approved quality average 18mm thick River wash finish Granite of required size, approved shade in floor, otta, skirting, pavement, plaza or similar in any pattern including average 20 mm thick cement mortar bedding in 1:6 laid and jointed with white cement and matching pigment including rubbing, curing, finishing, cleaning etc complete as directed by EIC. Sample shall be approved before execution. Laying patern shall be as per drawing and instruction of EIC for all floors/ all levels/ all heights and all shapes. (Only finished work will be measured.)
Providing material and labour for fixing average 18mm thick mirror polish Granite of uniform size and colour for treads and risers of stair, sill, jams of window, coping etc size 1200mm to 2500 mm long, of approved shade, including necessary machine - cut edges (uniform thickness) rounded edges, as per design in required sizes and shapes over 20 mm (average) thick bedding of cement mortar 1:6 (1 cement: 6 coarse sand) laid and jointed with white cement and matching pigment including rubbing, re-polishing after fixing to remove any undulation between the joints (if required) with different grades of Emery, refilling of open joints, curing, daily cleaning and mopping, as directed for at least 15 days or up to the satisfaction of the EIC etc complete for all floors any heights, any lead and lift as per approved sample by Architect, drawings and instruction of EIC. The rate includes machine cut edges of uniform thickness, champhering and mirror polishing of edges and maintaing upto hand over the project.
Providing material and labour for fixing machine cut average 18mm thick mirror polished Granite stone slab of approved shade as per approved sample for dado, cladding, skirting etc., in required design and pattern as per drawing, laid on 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, or fixed with stone fixing adhesive as per manufacturer's specifications including mirror polishing, pencil sharped edges, edge polishing, rubbing, curing, finishing, necessary scaffolding, maintaining upto handling over the project etc complete for all floors any heights, any lead and lift etc complete as directed by Engineer Incharge. Baking coat plaster for dado shall be paid in relevant tender item. Shade of skirting must be match with flooring stone.
Providing material and labour for fixing both side average 18mm thick mirror polished Granite stone slab as per sample approved by Engineer in charge with edges rounded and mirror polished, of required size fixed as urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement mortar 1:2 (1 cement : 2 coarse sand) as per drawing and as per direction of Engineer-in-charge. All expose edges shall be champhered and mirror polished. Rate shall be inclusive of chasing, cutting, edge champhering, edge polishing, curing, finishing, maintaining upto handling ovre the project etc complete for all floors all level etc complete as directed by Engineer Incharge.
Providing material and labour for fixing mirror polished average 18mm thick best quality Granite stone slab as per sample approved by Engineer in charge with edges rounded and mirror polished, of required size fixed as platfrom/ vanity counter by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement mortar 1:2 (1 cement : 2 coarse sand) as per drawing and as per direction of Engineer-in-charge. 75mm high facia shall be fixed at the edge of platform with epoxy or stone fixing adhesive as per drawing. All expose edges shall be champhered and mirror polished. Rate shall be inclusive of chasing, cutting, pencil sharped edges, edge polishing, making holes, curing, finishing, maintaining upto handling ovre the project etc complete for all floors all level etc complete as directed by Engineer Incharge. Installed area of platform and facia shall be measured for payment.
Providing material and labour for laying sandwich platform comprising of a) Sandwich of 18 mm thick single side polish Granite of approved size, shade and sample on top and 30 mm thick polished kota in bottom with 25mm thick cement mortar (1:4) in between b) At centre vertical sandwich supports of 30 mm thick two kota stone on sides and 20mm CM (1:4) in between and at both end walls vertical supports of 18 mm thick double side granite. c) 75 mm raised platform at bottom with kota on top and 50mm CM (1:4) at bottom, kota stone skirting as per design and approved sample. The rate includes rounding, champhering and mirror polishing of edges, facias of granite, MS support including necessary bonding adhesive (if required). Rate shall be also inclusive of curing, making holes & cutouts for sink, wash basin, Piller tap/ Bib tap but excluding the cost of MS work, plumbing fixtures ans sink. at all floors all height etc complete as directed by Engineer Incharge. (Only plan area shall be measured & paid for). Rate shall be included all kota & granite mentioned in above.
Providing material and labour for laying machine cut single polished 18mm thick Jesalmer yellow stone in flooring, band etc as per design and drawing over 20 mm thick cement mortar 1:3 and pointing in joints in white cement with matching pigment, curing etc. complete. The rate should also include for polishing with different grades of emery, daily moping with water, buffing, finishing at all floors any heights, any lead and lift etc complete. as directed by Engineer Incharge.
Providing material and labour for roughened strip 2.5 cm wide to form antiskid surface on treads of stairs in any type of stone including forming straight deep curved gishi (groove), 6 mm wide & 4 mm deep on two sides of the roughened area, chiseling, polishing the edges, sides and bottom of gishi etc. complete as per sample approved for all floor, all height. Only one time length of tread of stair shall be measured for payment.
Providing material and labour for laying broken china mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles (of any shade) to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall, curing, clearing with water and oxalic acid etc for all level, all height as directed by engineer in charge.
Providing material and labour for laying Cement Mortar for additional floor bedding in Cement Mortar 1:6 (1-Cement: 6 - coarse sand) including curing etc for all floor, all level all height. Additional bedding thickness shall be as per drawing and as directed by engineer in charge.
Providing material and labour for laying Porcelain Mosaic tiles of make by piccolo, Italia or Equivilant in different sizes (25mm x 25mm/ 50mm x 50mm/ 100mm x 100mm) having 8 mm thickness with water absorption less than 0.08% and conforming to IS: 15622, in any colours and shade, in Water body, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints for al depth al level as directed by engineer in charge. The Glass mosaic tile shall be fixed as per approved pattern and design. Sample to be approved by Architect.
Providing material and labour for fixing 12 mm thick Engineer wood flooring of approved pattern and shade as given by the Architect of approved make and as per manufacture’s specification confirming to British Standards BS EN 14904. Rate shall be inclusive of foam base underlay sheet as sound barrier and/ or vapor barrier and all the accessories like edge strip, joining strip, quarter strip, moulding strip, corner strip, etc. required as per design. Uniform gaps should be left on all sides to allow expansion and contraction of material. Flooring planks shall have micro bevel edges with lock n fold locking installation system. The gaps are covered with the help of accessories etc. finished in all respects as per the manufacturers specifications. The floor shall be laid in place with matching original skirting and profiles as approved and as per recommendations of approved manufacturer over base of existing flooring for all floor all level. The contractor shall get the sample and pattern approved by the Engineer-in-Charge before execution.
Sec.10.0 Structural steel works Providing material and labour for, fabricating, assembling, hoisting/ erecting and fixing in position at all heights/ all levels/ all floors/ all shapes & sizes with all leads & lifts using MS Rolled Steel Sections, Hollow sections, Tubular Sections, MS Plates, Chequered Plates, MS Pipes, Perforated Sheet, Flats, Bars , Angles, MS Sheet, Girder, Beam, cattle trap, deep threaded MS bolts, threaded J bolts, insert plate, support plate etc as per drawing. all confirming to latest relevant IS codes for the work of steel structures like staircases, railings, handrail, jali, gates, grills, bracings, platforms, brackets, monkey ladder, cattle trap, rungs, false ceiling frame work, Roof canopy, fencing posts, M.S. Screen & fencing jali frame work etc. including straightening, cutting, bending, bolting and welding the members all as per approved shop drawings and as per detailed specifications (for materials & workmanship) including necessary scaffolding/ staging etc. complete and comprising of Profile Cutting, Smooth grinding/ machining of edges/ faces/ all welding joints; Necessary welding; Machine drilling of holes for joining/ anchoring; dry sanding, degreasing (wet cleaning) & preparation of rustfree surface manually or mechanically, metal putty to make the surface even and smooth, 1 coat of epoxy primer and 2 coat of PU paint of approved make shade of paint over all the surfaces of the steel sections. The Contractor shall prepare shop drawing as per GFC drawing and as per actual site condition and get approved before execution by engineer in charge. (Standard measurements will be paid for as actual cut length used at site)
Providing and fixing in position, interlocking rolling shutter of approved make, made of 18 gauge, 75mm wide cold rolled GI lath interlocked, including top cover (20 gauge), spring, axles (specially designed shaft), guide rails (10 gauge), tees, iron pulleys, ball bearings, handles, arrangement for inside and outside locking arrangement, with Mechanical Type (Gear Arrangement), holding down bolts embedded in CC 1:2:4 / anchor fastener of HILTI or equivalent including 1 coat of Rustocap and 2 coat of Hi-Gloss Metal PU Paint of approved make and shade over all the surfaces etc. as directed. (Measurements considered for payments shall be clear size of opening plus guide channels on both the sides for width and 450mm on top for drum height.)
Providing and fixing stainless steel (Grade 316) Railing and baluster system of approved make stair railing, hand rail, bump rail, guard rail, with knock down system made of Hollow or solid secion i.e. tubes, square, flat, plates, bar etc with base plate Cover cap, finishing accessories, infilled holding brackets, fixing accessories etc. for any type of design, shape (plain/ curvature), size as per drawing. Railing shall be top mounted or side/ wall mounted. Railing shall be fixed with SS 316 grade anchor fastner of required size and as per fixing position of approved make. No Welding OR Fabrication shall be allowed at site. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Sample shall be approved before execution. Contractor shall arrange mock up of railing system (2 or 3 no) in required length as directed by Architact and Engineer in charge. Contractor shall protact railing system uptill handeling over the project.
SS water trough Providing material and labour for, Fabricating and fixing SS 316 grade water trough of size 300mm x 450mm with 300mm high SS sheet cladding (dedo) made out of 1.2mm thick sheet and required size of angle, flat etc in satin/ brush finish including supporting fittings made out of SS 316 grade solid rods, flats, anges, compatible SS anchor fastener (mechanical or chemical) as per manufacturer's specifications, SS supporting arrangement, latth work, argon arc welding bending and bends as per the detail drawing with best (high) quality finish & as per the a sample approved by Architect and as directed by engineer-in-charge. Rate shall be inclusive of all material, labour and wastage for all floor, all height, all level. Water trough shall be measured in Rmt. Installed length shall be measered. Contractor shall prepare shop drawing based on concept drawing ant get approved before execution.
Extra for providing material and labour for Hot dip galvanizing work confirming to IS 4759/ 2629/ 2633 with zinc of 610 GSM thickness on Cable tray, Railing, Handrail, facade framing, supports for mechanical equipments, garbage box, Street furniture and similar works etc made from solid flat, bar, RHS, SHS, tubular hollow sections etc. as per the drawing and as instructed by engineer in charge. The rate shall include preparing the surface by shot blasting/ acid washing prior to hot deep galvanizing, labor, tools, machinery etc complete (Sample to be approved). The weight of steel sections before galvanization shall be measured for payment. The cost of steel sections shall be paid for separately under relevant item.
Sec.11.0 Painting works White washing with lime on wall and ceiling surface (two coats) to give an even shade including thoroughly booming the surface to remove all dirt, dust; mortar drops and other foreign matter etc complete for all floors, all heights, all level as directed by Engineer Incharge.
Providing material and labour for applying Distempeing (Two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on wall and ceiling surfaces to give an even shade, over and including a priming coat with alkali resistance primer of approved brand after thoroughly brushing the surface and other foreign matter and also including preparing the surface even and sand parpered smooth etc complete for all floors, all heights, all level as directed by Engineer Incharge.
Providing material and labour for applying (Synthetic) Plastic emulsion paint (minimum 2 coats) having VOC (Volatile Organic Compound) content less than 50 gm/ltr on newly/ existing dry interior plastered surface including ceiling, roof etc. at all heights/ all levels/ all surfaces to give an even shade on prepared (putty and primer work) surfcae. Sample to be approved before starting of the work by Architect/ EIC. Rate shall be inclusive of the cost of scafolding but excluding the cost of primer and putty work.
Providing material and labour for applying required coats (min two coats) of white cement based putty after thoughly brushing the surfaces free from mortar dropping and other foreign matter. Preparing the surface even and sand papered smooth, after applying every coat of putty complete. Priming coat of alkali resistant cement primer (water or solvent based) is to be applied over prepared smooth surface (undulation free) etc. complete as directed by engineer-in-charge. After application of putty work, wall surface shall be in levelled and without undulation. The rate shall include the cost of filler for filling the cracks on surface, thoroughly brushing the surfaces with sand paper to make it free from mortar dropping and other foreign matter, scaffolding etc. as directed by engineer in charge.
Providing material and labour for applying Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials etc complete for all floors, all heights, all level as directed by Engineer Incharge. Product to be
Providing material and labour for Wall painting with anti microbial premium quality acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ liter of approved make and shade, with additional teflon surface protection, anti microbial formula & stain resistant, including applying additional coats wherever required to achieve even shade and colour over acrylic wall putty and one priming of approved make for all floor all height etc complete asdirected by engineer in charge.
Providing material and labour for applying external finish of average 2 to 2.5mm thick acrylic polymer based texture and pattern with standard tool and applicator as specified by manufacturer on exterior surfaces at all heights including scaffolding to give even shades including thoroughly brushing the surfaces free from mortar droping and other foreign matter and sand paper smoothed as per the manufacture specifications etc. complete for all floor, all height, all level and up to the satisfaction of Engineer in-charge/ Architect. The rate includes making of grooves, pattas and finishing as directed by Engineer in charge. Paint shall be measured and paid in seperate tender item. (Item should be executed by approved applicator only.)
Sec.12.0 Roofing works Providing material and labour for fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have, light reflection 85% non-combustible as per BS 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC for the best thermal Insulation. The Light weight calcium Silicate tile shall be of approved texture of size 595 x 595 x 15 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24x28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200x600mm and secondary cross ’T’ to be interlocked at middle of the 1200X600mm panel to form grid of size 600x600mm resting on periphery walls/ partitions on a perimeter wall with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges light weight calcium silicate ceiling tiles in the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked paint, as per specifications, drawings and as directed by engineer-in-charge.
Providing & Fixing M/F Suspended 12.5mm Plain Gypsum Board which includes GI Perimeter Channel is fixed along the perimeter of existing wall/ partition with the help of screws at 600mm centres. GI Ceiling Angle is suspended at up to suitable height as per sight conditions by fixing it to the GI soffit clit with Soffit Cleat and Rawl Plug creating 1220mm x 1220mm grid. GI Intermediate channel is fixed to the GI Ceiling Angle with 2 Nos of 4.2x13 GI metal to metal screw. The GI Ceiling Section is then fixed to the GI Intermediate Channel with the help of Connecting Clip and in direction perpendicular to the Intermediate channel at 457mm c/c. All framing and grid section shall be GI (as per IS 513) having yeild strength 300 mpa and galvanized finish of 150 GSM as per IS 277. Single layer of 12.5mm tapered edge Plain Gypsum Board (Confirming to IS 2095-Part-I, 2011) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing Compound & Joint Paper tape. The contractor should prepare shop drawings based on the concept drawing and get it approved by the Engineer-in-charge. After approval of drawings, the contractor shall prepare the sample based on the drawing and get it approved by the Engineer-in-Charge before execution. Rates shall be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights/ air-conditioners, grills, diffusers etc & providing additional sections for strengthening the openings/ cutouts, making grooves between wall & board or as per drawing for all floor, all level, all height etc as directed by Engineer in charge. Area of cutouts shall not be deducted and no extra payment shall be considered for additional sections provided. Only plan area shall be considered for payment.
Metal False Ceiling: Providing & Fixing true horizontal level suspended ceiling comprising of GI Clip-in with double pip self-leveling consisting of 600x600mm clip in tiles of galvanized steel in 0.5 mm thickness with bevel edge in pre-coated Global white color with Light Reflectance > 75% and fire performance of Class 0/Class 1 as per BS 476 Part 6 & 7 standards. Warranty Certificate of 10 Years and Test Reports for Fire rating shall be provided by Vendor. Installation: To comprise 3000mm long ‘C’ channels spaced at 1200mm centers securely fixed to the structural soffit using 6mm dia threaded rod connecting C- channel hanger at 1200mm C/C and anchor fastener. The last hanger at the end of each C channel should not be greater than 600mm from the adjacent wall. Use a C-channel connector for splicing two pieces of C-channels. 4000mm Main carriers (spring tee bars) shall be spaced at 600mm centers in a direction perpendicular to the C-channels and secured at every intersection with C channel using a hanger. Use connector to splice two pieces of main carriers. Tiles should be clipped in between two carriers (spring tee bars) from below. Perimeter trims to be of wall angles of size 3000x19x32mm in white color secured to walls at 450mm maximum centers. Installation to be carried out by trained Installation team and as per recommended procedure of approved manufacturer. Rates shall be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights/ air-conditioners, grills, diffusers etc & providing additional sections for strengthening the openings/ cutouts, scafolding, making grooves between wall & board or as per drawing etc complete for all level, all height, all floor amd as directed by Engineer in charge. Only plan area shall be considered for payment.
Perforated Gypsum tile acoustic false ceiling : Supplying material labour for fixing of Suspended ceiling system with 12.5mm thick glass fibre perforated gypsum plaster board/ tile of any size having any type of edges and any shape, any size, any pattern perforation and GI suspended framing system. This includes ribbed frame Perimeter Channel fixed to brick wall/partition with the help of nylon sleeves and screws at 600mm centres along the perimeter of ceiling. Then suspending ribbed section used as intermediate channel from the soffit at 1220mm centres with Ceiling Angle fixed to RCC Slab with Soffit Cleat and steel expansion Fasteners @ 600mm Centres respectively. Ultra frame ribbed Ceiling Section are then fixed to Intermediate channel with the help of four point connecting clip (0.8mm thick) and in perpendicular direction to the intermediate channel at 600mm centres. All framing and grid section shall be GI (as per IS 513) having yeild strength 300 mpa and galvanized finish of 150 GSM as per IS 277. 12.5mm thick glass fibre perforated gypsum plasterboards/ tile of any size having any shape, any size, perforation of any pattern is screw fixed with 25mm long Drywall screws at 230 mm centres. 50mm thk 24kg/m3 glasswool should be placed between the frame and perforated board with the help of Glasswool tissue bag. The screw fixing of gypsum plasterboards to the metal framing at the periphery, openings and cut edges should be at 150mm centres. Finally square or tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing compound, Joint Paper tape and two coats of Drywall Top Coat as per the drawing & approved sample. Rates shall be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights/ air-conditioners, grills, diffusers etc & providing additional sections for strengthening the openings/ cutouts, scafolding, making grooves between wall & board or as per drawing etc complete for all level, all height, all floor amd as directed by Engineer in charge. Only plan area shall be considered for payment.
Wooden veneer ceiling Providing and fixing ply + veneer false ceiling on GI framing system for false ceiling work as per drawing and as following. 1) GL framing system which includes Perimeter Channel is fixed along the perimeter of existing wall/ partition with the help of screws at 600mm centers. Ceiling Angle is suspended at up to suitable height as per site conditions by fixing it to the soffit Cleat and Rawl Plug to creating grid. Intermediate channel is fixed to the Ceiling Angle with 2 Nos of 4.2x13 metal to metal screw. The Ceiling Section is then fixed to the Intermediate Channel with the help of Connecting Clip and in direction perpendicular to the Intermediate channel. All framing materials shall be of GI (IS513), YS-300Mpa, Finish-Galvanized 150GSM (IS 277). 2) 12mm backing play wood shall be 303 BWR grade of approved make shall be fixed on both side of MS framing of false ceiling work with SS screws. 3) 4mm thick teak veneer shall be fixed on ply with adhesive, hardware etc complete. 4) Wooden Beading shall be applied on all the sides of the panels of required size. 5) All exposed surface of wooden shall be lacquer polished of approved make, shade and texture. Actual area of veneer surface shall be measured and paid in sqmt without considering any wastage. Contractor shall get the sample of all material approved by Architect/ Engineer-in-charge.
Providing material and labour for fixing fabricated metal single shutter/ double shutter trap door made from 0.8 mm MS sheet, Inner Frame - 1.5 mm, Outer Frame - 2mm MS sheet and finished with powder coating of approved shade/ enamel/ acrylic paint (primer + 3 coats of paint) of approved make and shade. Door shall be installed on existing false ceiling framing with extra MS suspender with necessary hardware like allen key lock, hinges/ pivot, safety chain etc complete as directed by engineer in charge. Rate shall be inclusive for providing, loading/ unloading, transporting and installation at all floor all height but excluding the cost of extra suspender for installing the trap door. Area of trap door with frame shall be measured for payment.
Mineral wool insulation Providing material and labour for installing 50mm thick 48kg/cum density mineral wool (pre-wrapped) in the wall panelling and over acoustic false ceiling as per required application, for all floor, all height, all level as per drawing and as directed by engineer in charge.
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
Providing and fixing precoated galvanised steel sheet roofing plain Ridges (500 - 600mm) having 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
Providing and fixing of 16 mm thick Multicell UV protected Polycarbonate Panel System with 5 cells and 6 walls structure over structural steel / MS purlins per approved colour/shade for plain or curved (dome type) roofing work. Co-extruded UV protected panels shall have width of 900mm to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical standing seam at both sides of the panel. Welding or gluing up of standing seam is not acceptable. Panels shall be fixed on purlins with Stainless steel retention clips and connectors. Snap-on connectors to interlock the panels shall have a grip-lock single tooth locking mechanism to ensure maximum uplift capability. Panels shall have End-cap/ Aluminium U-profile/ Glazing bar for ends as per requirement. The weight of the system shall not be less than 2.30 kg per square meter. Panel shall be co-extruded with specialist-glare compound to make it anti-glare/soft light to prevent glare and sun streaks. Panels shall be fixed over structural steel/ MS purlins conforming to the detail technical specifications and as per approved architectural drawings. The rate shall include the cost of above specified materials, fixing of the sheet, scaffolding and labour charges for working at all levels, leads and heights as directed by engineer in charge. Surface area of roof sheet shall be measured for payment. The supporting MS structure for panel shall be paid separately in relevant tender item.
Fiber cement board : Providing material and labour for fixing exterior grade cement fibre board/ plank cement pattas of 8 mm thickness at exposed concrete ceiling/ wall/ beam bottom with brass/ SS head screws as per drawings, specification and sample approved at all floors, all levels and all shapes etc complete as directed by engineer in charge. Rate shall be inclusive of all material, labour, scafolding, tools, tackes etc complete.
Sec.13.0 Demolition & Dismantling Work Demolition including stacking of serviceable materials and disposal or unserviceable materials at nonobjectionable place with all leads and lifts including cutting the reinforcement, and finishing the broken surfaces to match with the surroundings etc. complete : RCC Works.
Demolition including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (i) P.C.C. work
Demolition of Brick Work/AAC block work with plastered surface/ wall dedo including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.
Dismentaling tiled of stone floors/ wall tiles laid in mortar including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.
Dismentling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats architraves, holdfasts and other attachment etc. complete and stacking them within all lead and lift.(i) Not exceeding 3 Sq.M. in area.
Dismentling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats architraves, holdfasts and other attachment etc. complete and stacking them within all lead and lift.(ii) Exceeding 3 Sq.M. in area.
Removing and scraping of old deteriorated plaster of any thickness fromm wall / R.C.C member including stacking of serviceable material and disposal of unserviceable from site of work with all lead and lift.
Dismentling steel work including distempering and stacking the materials with all lead and lift.
Dismantling santtary fittings like wash basin . W.C. pan Indian and European type, flushing tank etc. including stacking the materials with all lead and lift.
Dismentalings any type of ceiling or partition walls, wooden trellies work including grid and suspension system with all elements stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.
Sec.15.0 General Development and Road works Box cutting the road surface to proper slope and camber for making a base for road work including removing the excavated stuff and depositing on the road side slope as directed upto 1 Km lead and all lift.
Providing and laying rubble soling in plinth and sub-base of road, compacted thickness specified as following, using specified size of hard stones for average 150mm thick soling, filling, covering and leveling the surface with a layer of earth after filling the voids (upto 25%) with sand, smaller sized black trap stones 20-40mm, 40-63mm, 63-90, 90-150mm size of stone/metals or stone chips, including watering, ramming well and compacting or consolidating each layer by static roller/ vibratory roller of required capacity as directed by Engineer-in charge.
Construction of Granular Sub Base (GSB) by providing coarse graded material of any grade, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, including all material, labour, machinery with all leads and lifts etc. complete as per MORTH specification and as directed by Engineer in charge.
Providing material and labour for, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tripper to site, laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density including all material, labour, machinery with all leads and lifts etc complete as per MORTH specification and as directed by Engineer in charge.
Providing material and labour for applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 7.5 kg/10sqm using mechanical means including all material, labour, machinery with all leads and lifts etc complete as per MORTH specification and as directed by Engineer in charge.
Providing material and labour for laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour/ DMP 60-90 TPH capacity using crushed aggregates of any grading, premixed with bituminous binder @ 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction etc complete including all material, labour, machinery with all leads and lifts etc complete as per MORTH specification and as directed by Engineer in charge.
Providing material and labour for applying Tack Coat with Cationic Bitumen Emulsion RS1 complying with IS:8887. The tack coat shall be applied by a self-propelled or towed bitumen pressure sprayer, equipped for spraying the material uniformly at the rate of 2.5Kg/Sqmt etc complete including all material, labour, machinery with all leads and lifts etc complete as per MORTH specification and as directed by Engineer in charge. No dilution or heating at site of RS1 bitumen emulsion shall be permitted.
Providing material and labour for laying Bituminous concrete BG 40 with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ min 5.4 % of mix, transporting the hot mix to work site, laying with a self-propelled paving machine equipped with an electronic sensing device to the required grade, level and alignment, rolling with 8-10 tonne static weight or vibratory roller or with a pneumatic tyre roller of 12 to 15 tonne weight to achieve the desired compaction as per approved design mix etc complete including all material, labour, machinery with all leads and lifts etc complete as per MORTH specification and as directed by Engineer in charge.
Asphalt Painting Providing and laying Asphalt painting on B.T. surface with bitumen grade 60/70 (VG-30) @ rate of 5 kg/10 smt by Mechanical sprayer and spreading the stone dust on prepared surface at the rate of 0.03 cum/10 smt. and rolling with smooth wheeled and penumatic roller and brushing etc. comp.
Providing material and labour for laying precast fair finish curbing of (factory made) RCC M25 grade curbing of required size with all accessories including necessary excavation, cutting the road, laying PCC 1:4:8 (1 cement: 4 sand: 8 stone aggregate 20/37 mm. down size), exposed rendering, curing, flush pointing CM 1:3 as per the drawing, as per approved sample and as directed by Engineer in charge.
Providing material and labour for laying shot blasted Non-interlocking (factory made) high density 60 mm thick M35 grade any colour brick type paver blocks of size 200mm x 200mm/ 200mm x 100mm of approved make and shade for footpath, parking areas, service lanes and other areas as mentioned in the drawing including average 50 to 80 mm thick bedding layer of coarse sand below paver block. Laid paver block shall be mechanically compacted and as directed by Engineer in charge. The work shall be executed in line and level by skilled mason of flooring work only for paver blocks. It should be laid in such a way that the No cutting of the paver block to be necessary and if required, cutting of paver block by machine cut only. The Finished surface of the paver block shall have coarse sand texture finish. Sample to be approved before starting of the work by Architect/ EIC.
Providing material and labour for laying shot blasted Non-interlocking (factory made) high density 80 mm thick M45 grade any colour brick type paver blocks of size 200mm x 200mm/ 200mm x 100mm of approved make and shade for footpath, parking areas, service lanes and other areas as mentioned in the drawing including average 50 to 80 mm thick bedding layer of coarse sand below paver block. Laid paver block shall be mechanically compacted and as directed by Engineer in charge. The work shall be executed in line and level by skilled mason of flooring work only for paver blocks. It should be laid in such a way that the No cutting of the paver block to be necessary and if required, cutting of paver block by machine cut only. The Finished surface of the paver block shall have coarse sand texture finish. Sample to be approved before starting of the work by Architect/ EIC.
Providing material and labour for laying 60mm thick Solid Concrete Combination Cobbles of differant size, made by vibro pressed method of VYARA or equivalent as approved by Architect/ EIC, with +/-3mm tolerance and thickness of wearing layer not less than 5mm of any color and shade (UV Light resistant fast colours from Lanxess only to be used) having compressive strength of 30 Kg/cm2 for footpath, parking areas, service lanes and other areas as mentioned in the drawing. Combination cobbles shall be laid as per approved pattern and suggested by manufacturer and Architect. Including providing and laying average 50 mm thick average bedding layer of coarse sand below the block as per required grading and specification.Laid paver block shall be mechanically compacted and as directed by Engineer in charge. The work shall be executed in line and level by skilled mason of flooring work only for paver blocks. The Finished surface of the paver block shall have coarse sand texture finish. Sample to be approved before starting of the work by Architect/ EIC.
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm PVC couting on outer side including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.
Providing material and labour for laying cement concrete broom finish/ smooth finish pavement for plinth protection/ CC Road 100 –150 mm. thick with M25 concrete including giving a floating coat of 1:1 cement mortar, with Nominal temperature steel, tie bar, dowel bar as per MORTH specifications of section -6 etc complete as specified by the Engineer-in-charge. The rate shall be exclusive of reinforcement steel, dowel bar etc. The same shall be paid in relevant tender items. Rate shall be inclusive of concrete (to be laid in alternate panels size shall be apprx 4.5mt X 5.0mt ) with fair finished steel channel formwork, saw cutting of construction & contraction joints in width 3 to 5 mm x 1/4 to 1/3 thickness of pavement, filling the 25mm x 20 mm (BXD) expansion joint approximately at every 30 mt with readymix bitumiNous filler as per sample approved & directed by engineer incharge etc complete. Screened Sand to be only used.
Vaccum dewatering Extra for carrying out vaccum dewatering & Power floater treatment in roads, pavements, floors well compacted, mechanically vibrated with screed vibrator, finished to required levels, floated with neat cement and power trowelled to get desired smooth finish / broom finish, over a leveling course, including MS channel or box shuttering, curing for 10 days with gunny bags etc complete. The size of panel should be approximately 3.75 x 5.5 m or as directed by Engineer. The Contraction joints to be formed at every 5m distance by grooving with mechanical saw within 48 hrs. Groove/sawed joints/ longitudinal joints shall be made of 6mm width and 25 mm depth min (1/3 rd depth of the pavement) as shown in the drawing. The rate shall be inclusive of labour, making the grooves and machinery cost.
Providing material and labour for fixing FRC (Fiber reinforcemed concrete) Heavy Duty Man Hole Cover with frame of intrnal dia 560mm with 100x2mm MS flat allround, 16mm ø plain round bar for lifting the cover & should be fitted with plastic cups etc complete as directed by engineer in charge. On the upper periphery of frame 25 x 3 mm wide MS flat with hot dip galvanizing should be well embed in concrete to protect the edges of frame.
Providing material and labour for fixing Ductile iron manhole frame and cover/ grating/ chamber cover of approved make and type. Man hole cover shall be any type (hinged type, double sealed or recess type), any shape (square/ rectangle/ square frame with round cover) any grade (light duty/ medium duty/ heavy duty) of required loading capacity having double sealed system as per manufacturing standard BS EN-124, with proper lifting arrangement, black bituminous coating, including fixing in CC and finishing etc complete as directed by engineer in charge. Cover shall be as per drawing and as per approved sample. Recess manhole cover depth shall be according to pavement/ finish as per drawing.
FRP Recessed Man hole cover Providing and Fixing heavy duty double seal FRP Manhole cover with frame of 25MT capacity, in matching shade of surrounding pavement and design according to EN - 124:1994 of HP or equivalent of clear opening size of 600mm x 600mm and recesse depth 80mm, with client's logo etc. complete as approved by architect and as directed by engineer in charge. Frame shall be embaded in concrete of M25 grade and top level of frame shall be flush with road level. Frame and cover shall be with 4 number lifting key with proper lifting arrangement. Rate shall be inclusive of cover frame and concrete work. The rate includes carting upto any lead from store to site as per directed by engineer in charge.
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
FRP UG Tank cover Providing and Fixing mediumduty double seal FRP UG Tank cover with frame of 5MT capacity, in matching shade of surrounding pavement and design according to EN - 124:1994 of HP or equivalent of clear opening size of 600mm dia having frame thickness average 50mm and cover thickness 25mm, of weight average 35 Kg with client's logo etc. complete as approved by architect and as directed by engineer in charge. Frame shall be embaded in concrete of M25 grade and top level of frame shall be flush with road level. Rate shall be inclusive of cover frame and concrete work.
Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.
Providing and fixing Cast iron manhole frame and cover/ grating of approved make and pattern. Man hole cover shall be any type (hinged type or recess type), any shape (square/ rectangle/ square frame with round cover) any grade (light duty/ medium duty/ heavy duty) of required loading capacity having double sealed system as per manufacturing standard BS EN-124, with proper lifting arrangement, black bituminous coating, including fixing in CC and finishing etc complete as directed by engineer in charge. Cover shall be as per drawing and as per approved sample. Recess manhole cover depth shall be according to pavement/ finish as per drawing.
Garden Soil Filling Providing material and labour for Filling mixture of good quality garden soil obtained from outside for all lead and lift with farm yard manure and pesticides in exacavated tree pit, tree pit, shrub area including watering, ramming well, consolidating, compacting and dressing etc. complete, as directed by engineer in charge. Excavation shall be paid in revevant tender item.
Providing material and labour for making tree pit with 800mm diameter NP2 class hume pipe with 600 mm height to be placed on the filled garden soil and outside area of the hume pipe to be filled with the good quality earth. Hume pipe shall be filled with the mixture of garden soil, farm yard manure and required pesticides etc. complete as directed by Engineer in charge. Excavation and soil filling shall be paid in relevant tender item.
Tree plantation Supplying material and labour for planting of trees including termite treatment, and planting of plants in existing prepared tree pit or excavated pit. (height 4'-6' above bags/pots). Soil mounts 4”-6” in size. Tree plantation should be carried on neatly accurately and with perfection as per drawing and instruction given by the EIC. Plastic bags or pots should be removed carefully and soil around the roots should not be dropped or disturbed much. Bill shall be placed after completion of maintenance period but not before stabilizing the hedges. Rates for mortality to be inclusive. Providing and fixing tripod made of wooden balli, height 1.50mtr. Top bracket to be 300mm x 300mm. leg embedded in ground up to 300mm and to have tar coat. Work shall be done as shown in the drawing or as directed and approved by EIC. Excavation and soil filling shall be paid in relevant tender item.
Supplying well grown shrub plants and ground cover plants of average height 3' to 4' and planting in planter box or prepared ground area (prepared and filled with garden soil filling). Plants should be disease free and fungus free in 8"x 10" polythene bag. Plastic bags or pots should be removed carefully and soil around the roots should not be dropped or disturbed much. Distance between two shrub shall be as per drawing. Bill shall be placed after completion of maintenance period but not before stabilizing the shrubs. Mortality rates to be inclusive. Work shall be as directed and approved by Eingeer in charge. The ground coverage should be dense and uniform throughout the planting area. Excavation and soil filling shall be paid in relevant tender item.
Lawn Plantation : 1) Supplying material and labour for filling with good quality garden soil obtained from outside, including watering, ramming well, consolidating, compacting and dressing etc. complete, as directed. Dressing and leveling the area by spreading 2"-3" of good quality soil & manual compaction as required and as approved by EIC. 2) Supply and spreading of FYM (2.50 Cum in 100 Sqm area) shall be done in proper slope as per mention in drawing including watering and fine dressing. Termite treatment to be done before laying of FYM. 3) Supplying and planting of the specified lawn on above described surface. Plantation of lawn at distance 8cm c/c. When the grass is approximately 3 cm high, it shell be rolled with a light wooden roller and when it has grown up to 5 to 8 cms above the ground, weeds must be removed and after that lawn shall be cut to the appropriate height using the lawn cutter for minimum 3 to 4 times. Weeds shall be removed regularly and periodic top dressing of FYM shall be done during the maintenance period (Bill shall be placed after completion of maintenance period.) Work shall be done in the pattern as shown in the drawing or as directed and approved by Engineer in charge. Rate shall be inclusive of surface preparation for lawn planting, Termite Treatment, Plantation, Maintenance, Watering till the end of Maintenance Period as per the instruction of EIC. Garden soil filling with FYM shall be paid in relevant tender item.
Tree pit cover Providing material and labour for fixing tree pit cover around the tree pit, factory made exposed /fare finish precast Tree pit cover block of two halve in FRC concrete of size - 0.90Mt x 0.90Mt x 0.065mt including transporting, fixing etc. complete as directed by Engineer in charge. The rate shall also include for erecting and fixing the pieces in position as shown in the drawing with necessary equipments without ant demage. (Sample to be approved)
Providing material and labour for fixing tree guard upto height of 1.8 metre fabricated from 30 x 30 x 3mm angle and 30 x 30mm weld mesh as per drawing and details. Necessary provisions for the anchoring to floor shall be made in the tree guard. Tree guard shall be painted with two coats of yellow oxide and three coats of enamel paint as per the shade approved by EIC.
Providing, casting, hoisting, installing in position Precast Reinforced cement concrete (M25) Bench as per design and drawing having 40mm thick mirror polished kota of approved shade on top. groove of same width as mortar thickness shall be provided between top kota stone and concrete top as per drawing. Remaining surface of bench shall be expose rcc work. All edges of kota shall be champhered and polished. Rate shall be inclusive of RCC, reinforcement and kota work with all material, labour for making, fixing, loading, unloading, hoisting, placing, polishing etc complete as directed by engineer in charge. Sample shall be approved before execution of work. Size of Bench - 1500 L x 450 mm W x 380mm H (100mm thick seat) with tappered solid base (1100mm x 200mm at bottom and 1200mm x 300mm at top)
Providing material and labour for fixing G.I. barbed wire Fencing on existing MS post provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs etc for all height all level as directed by Enginer in charge. (cost of MS posts to be paid for separately) Payment to be made per metre cost of total length of barbed wire used.
Providing material and labour for fixing in position 80 mm thick factory made machine batched & machine mixed Solid Precast RCC Rectangular Covers on cable trench of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.
Providing material and labour for placing in position 80 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.
Supplying mterial and labour for laying of following size DWC HDPE pipe of 63mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.
Supplying mterial and labour for laying of following size DWC HDPE pipe of 90mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.
Supplying mterial and labour for laying of following size DWC HDPE pipe of 120mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.
Supplying mterial and labour for laying of following size DWC HDPE pipe of 160mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.
Road Marking with hot applied thermoplastic paint for yellow edge line zibra patta, bump patta, centre line, edge line, cut patta with reflectorising glass beads on road surface and laying of hot thermoplastic compound 2.5 mm thick including reflectorising glass beads at 250 gm/smt area. Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35. The finished surface to be level uniform free from streaks and holes.
Cat eyes/ pavement marker (MMC nail less with stud at bottom) Made out acrylic styrene – acrylonitrile of high impact polystyrene fitted with moulded of methacrylate reflector cube corner reflector design filled with tightly adhering potting compound as per ASTM D-788 size 11.5 x 7 x 1.60 cm or 10 x 10 x 1.75 cm. provided with bituminous adhesive in sufficient quantity with each unit for fixing. No nail shall allow for fixing. Reflector on both sides, minimum reflective area 12.9 sq.cms on each face. Coefficient of lamination as per specification and compressive strength 13 Tonnes at 23 degree centigrade, ( B ) Both side lense. (With stud as per design, installed in concrete or asphaltic surface by drilling holes of suitable size and fixed with bituminous adhesive as directed)
Sculpture Providing and installing made out of metal, concret, acrylic, stone etc as per design and as aprroved by Architec. (Basic rate - Rs.1,00,000 with tax transportation, installation )
Providing and fixing SS 304 grade satin finish perforated dust bin / litter bin of size 850 mm x 300 mm x 850 mm and capacity 50 Ltr each bin madeout of minimum 1.2mm thick sheet with pole of Saflow, Jindal, KMGS and as per approved sample. Dust bin shall be floor mounted with both side pivot for tilting having stand arrangement. Both bin shall be covered with SS sheet. Dust shall be having chemical resistant, blended with stabilizers, Anti Corrosive, Anti Acidic, Non toxic and free from joints, welds or rims; open from either side for easy garbage drop even from distance, Dustbin shall be as per approved and seperate Dustbin for Dry and wet Waste shallbe provided (Green and Blue Colour Demarcation on it)
Providing material and labour for fixing rumblers strips of 500 x 100 x 15 mm of any design suggested by Architectect/ EIC like bottom design, chequered design, anti skid pattern specially designed for road grip as per drawing & sample approved by Architect which is covered with premix bituminous carpet at 1m centre to centre at approved locations to control speed marked with white strips of road marking paint etc complete as directed by Engineer in charge.
Supplying mterial and labour for laying of following size DWC HDPE pipe of 200mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.
Providing, Making and fixing SS 304 Emboss LOGO with back lited by LEDs/ SMD lightings behind the logo of size as per drawing for signage in English/Gujarati and the font style as approved sample or as per design and drawings. SS section shall be curved/ bend in shape of letter and same shape CNC cut letter. It shall be fixed on the wall with chemical anchor fastener at any level any height. All Edges and corners shall be smooth. Duco paint of approved make, shade in required coat with necessary primer and putty shall be applied on external surface of letter. Rate shall be paid in sqm. The rate shall be inclusive of scaffolding, drilling, fasteners, adhesive material etc complete for all heights as directed by engineer in charge. The rate shall also include cost of scaffolding, drilling, fabrication, finishing, adhesive material, sealant etc at all height and all lead. The contractor should submit the drawings based on concept design and do the sampling and get it approval before execution.
ACP sheet signage : Providing, Making and fixing 3 mm thick ACP sign of any shape and size and of approved make to be cut on CNC router cutting and smoothen all corners and edges. Matter shall be cut in 3M High intensity prismatic Reflective vinyl ASTM Type 4 and paste on it as per design and detail and as per manufacturer's specifications. UV stabilized lamination shall be done on it. The ACP sheet shall be fixed with clamp and angle on new or existing MS Pole as per drawing. Content of sign shall be letters (In Gujarati & English), graphics / maps, signs etc. in any colour as per design, drawing and approved by Architect and Engineer. All side of box shall be covered with fresh ACP sheet, but only one side elevation area shall be measured and paid in sqmt. Cost of MS Pole and Civil works shall be paid as per relevant tender items. The rate shall also include cost of scaffolding, drilling, fabrication, finishing, adhesive material, etc at all height and all lead, angle, fixing charges, etc. The contractor should submit the drawings based on concept design and do the sampling and get it approved before execution.
Surface/ wall mounted signs Providng and fixing of Modular Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal graphics to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be fixed on surface with SS 304 screw and signage pabnel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage.
Wall projected Providng and fixing of Modular Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal graphics to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Projection Bracket shall be of 3mm Aluminium extrusions having Anodized finish (same as framing). Projection Bracket shall be fixed on wall with SS 304 screw and signage panel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage.
Ceiling Hanging Providng and fixing of Modular Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal graphics to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be suspended from ceiling with suspension clips and cable (SS 304) with adjustable arrangement and signage panel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage.
Floor Directory Signage Providng and fixing of Modular Signages (removable) using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. For Flat panels, plotter cut vinyl letters to pasted and for sliding profile print to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be fixed on surface with SS 304 screw and signage pabnel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage. (Measurement : Actual area for directory signage shall be considered for payment.)
You are here/ map signage Providng and fixing of Modular Map Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. For Map, plotter cut vinyl letters to pasted and for sliding profile print to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be fixed on surface with SS 304 screw and signage pabnel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage. (Measurement : Actual area for directory signage shall be considered for payment.)
Pylon signage - 800mm x 2000 mm Providing and fixing of Totems of size 800mm x 2000 mm using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal structure to be made from ms section of required size with proper support in between and 3mm ACP to be slided from both sides. 3mm ACP to have 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty 3 mm ACP sheet with High intensity Prismatic Grade reflecitve sheeting with top hat of 2 mm Aluminium and bottom hat of MS 6 mm thick depending on size of Pylon.
Pylon signage - 450X1200 Providing and fixing of Totems of size 450mm x 1200mm using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal structure to be made from ms section of required size with proper support in between and 3mm ACP to be slided from both sides. 3mm ACP to have 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty 3 mm ACP sheet with High intensity Prismatic Grade reflecitve sheeting with top hat of 2 mm Aluminium and bottom hat of MS 6 mm thick depending on size of Pylon.
Providing and fixing Signage at Building terrcae or at other place made of - 1) 3mm thick Acrtlic to Acrylic cover letter in white colour having 100mm embossed in text or logo as per drawing or as suggested by EIC. 2) ACP/ GI reverse channel letter to uphold front letter 3) All side embossed by 90mm Aluminium channelium illuminate from front side 4) IP 67 grade water proof LEDs/ SMDs modules with 3 year opt door warrenty 5) Water proof/ Rain proof power supply with complete wiring including on site fixing for all height all level 6) Signage panel shall be fixed on MS struxcture, which shall be paid i relavent tender item. 7) installed signage board area shall measured for payment.
02-PLUMBING WORKS Section 1: Water Supply Construction of 2 Bore Wells at Site: The scope includes - Drilling of Bore Wells, Reaming of Bore holes, Lowering of Drop Line & Air Line up to water bearing zone, Compressed Air Cleansing up to availability of sand free discharge, Pipes, MS Clamps, MS Bore Plugs, MS Bail Plugs, Steel Bent Plates, Geohydrological Ground Water Investigation, Electrologging of bore holes, Chemical analysis of extracted water, Submersible Bore Well Pumps, Control Panels, Cabes, Column Pipes, etc complete to the entire satisfaction of the Engineer-in-charge, as per the below mentioned details:300 mm diameter (2 x 50 meters = 300 meters total length)
Providing and supplying ISI marked CI D/F Reflux Valves as per IS: 5312 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Reflux Valves PN 1.0 IS 5312 with ISI mark: 100 mm.
Providing and supplying ISI marked CI D/F Buttterfly Valves as per IS: 13095 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Butterfly Valves as per IS: 13095 PN 16 100 mm.
Providing and supplying ISI marked CI D/F Buttterfly Valves as per IS: 13095 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Butterfly Valves as per IS: 13095 PN 16 80 mm.
Providing and supplying ISI marked CI D/F Reflux Valves as per IS: 5312 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Reflux Valves PN 1.0 IS 5312 with ISI mark: 80 mm.
Providing and supplying ISI marked CI D/F Buttterfly Valves as per IS: 13095 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Butterfly Valves as per IS: 13095 PN 16 65 mm.
Providing and supplying ISI marked CI D/F Buttterfly Valves as per IS: 13095 (Latest Edition) of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking at position with necessary material for installation. Butterfly Valves as per IS: 13095 PN 16 50mm.
Lowering, Laying and jointing in position following CI D/F Reflux Valves, Butterfly Valves, Sluice Valves and Air Valves including cost of labour, jointing material, including nut bolts and giving satisfactory hydraulic testing complete. Sluice valves, Butterfly Valves, Reflux Valves: Dia 65 mm
Lowering, Laying and jointing in position following CI D/F Reflux Valves, Butterfly Valves, Sluice Valves and Air Valves including cost of labour, jointing material, including nut bolts and giving satisfactory hydraulic testing complete. Sluice valves, Butterfly Valves, Reflux Valves: Dia 80 mm
Lowering, Laying and jointing in position following CI D/F Reflux Valves, Butterfly Valves, Sluice Valves and Air Valves including cost of labour, jointing material, including nut bolts and giving satisfactory hydraulic testing complete. Sluice valves, Butterfly Valves, Reflux Valves: Dia 100 mm
Lowering, Laying and jointing in position following CI D/F Reflux Valves, Butterfly Valves, Sluice Valves and Air Valves including cost of labour, jointing material, including nut bolts and giving satisfactory hydraulic testing complete. Air Valves single ball flanges / screwed type: 25mm diameter
Providing and supplying C.I. Air Valves of approved make & quality of following class and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete. Air Valves single (S2) Type: 25mm diameter
Providing and supplying ISI mark G.I. Pipes with couplings of following class and diameter including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading unloading, conveyance to the dept. stores etc. complete: (IS - 1239) (Not for well / tubewell column pipe) Medium Duty: 100mm diameter
Providing and supplying ISI mark G.I. Pipes with couplings of following class and diameter including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading unloading, conveyance to the dept. stores etc. complete: (IS - 1239) (Not for well / tubewell column pipe) Medium Duty: 80mm diameter
Providing and supplying ISI mark G.I. Pipes with couplings of following class and diameter including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading unloading, conveyance to the dept. stores etc. complete: (IS - 1239) (Not for well / tubewell column pipe) Medium Duty: 65mm diameter
Providing and supplying ISI mark G.I. Pipes with couplings of following class and diameter including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading unloading, conveyance to the dept. stores etc. complete: (IS - 1239) (Not for well / tubewell column pipe) Medium Duty: 50mm diameter
Lowering, laying and jointing G.I. pipes with G.I. specials of following diameters in proper position, grade and alignment as directed by Engineer in charge including cov=nveyance from stores to site of work, labour, giving hydraulic testing, etc. complete: 100mm diameter
Lowering, laying and jointing G.I. pipes with G.I. specials of following diameters in proper position, grade and alignment as directed by Engineer in charge including cov=nveyance from stores to site of work, labour, giving hydraulic testing, etc. complete: 80mm diameter
Lowering, laying and jointing G.I. pipes with G.I. specials of following diameters in proper position, grade and alignment as directed by Engineer in charge including cov=nveyance from stores to site of work, labour, giving hydraulic testing, etc. complete: 65mm diameter
Lowering, laying and jointing G.I. pipes with G.I. specials of following diameters in proper position, grade and alignment as directed by Engineer in charge including cov=nveyance from stores to site of work, labour, giving hydraulic testing, etc. complete: 50mm diameter
Providing and fixing enclosed type water meter (bulk type) conforming to IS: 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions, etc. - 80mm diameter
Constructing masonry chamber 30 x 30 x 50cm inside, in brick work in cement mortar 1:4 (1 - cement; 4 - coarse sand) for stop cock with C.I. surface box 100 x 100 x 75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 - cement; 2 - coarse sand; 4 graded stone aggregate 20mm nominal size), including necessary excavation, foundation concrete in 1:5:10 (1 - cment; 5 - coarse sand; 10 - graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 - cement; 3 - coarse sand) 12mm thick, finished with a floating coat of neat cement, complete with common burnt clay non-modular bircks of class designatin 7.5.
Constructing masonry chamber 90 x 90 x 50cm inside, in brick work in cement mortar 1:4 (1 - cement; 4 - coarse sand) for stop cock with C.I. surface box 100 x 100 x 75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 - cement; 2 - coarse sand; 4 graded stone aggregate 20mm nominal size), including necessary excavation, foundation concrete in 1:5:10 (1 - cment; 5 - coarse sand; 10 - graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 - cement; 3 - coarse sand) 12mm thick, finished with a floating coat of neat cement, complete with common burnt clay non-modular bircks of class designatin 7.5.
Providing and fixing Class - 2 Gun metal gate valve as per IS: 778, with C.I. wheel of approved quality having Pressure Class Rating of Class 1, Gun Metal (Forged Brass) body as per IS: 318 LTB2, Screwed bonnet, inside screw, rising stem, intergal seat of rubber (EPDM), solid wedge, Trim of Copper Alloy, Asbestos gland packing, secrewed female parallel thread as per IS: 554, body having 1.5 MPa hydraulic pressure rating and Seat having 1.0 MPa hydraulic pressure rating. (screwed end). 65mm dia nominal bore.
Providing and fixing Gun metal gate valve with C.I. wheel of approved quality having Pressure Class Rating of Class 1, Gun Metal (Forged Brass) body as per IS: 318 LTB2, Screwed bonnet, inside screw, rising stem, intergal seat of rubber (EPDM), solid wedge, Trim of Copper Alloy, Asbestos gland packing, secrewed female parallel thread as per IS: 554, body having 1.5 MPa hydraulic pressure rating and Seat having 1.0 MPa hydraulic pressure rating. (screwed end). 50mm dia nominal bore.
Providing and fixing Gun metal Vertical Check Valve (non-return) valve of approved quality having Pressure Class Rating of Class 1, Gun Metal (Forged Brass) body as per IS: 318 LTB2, Screwed in cover with integral seat, Trim of Copper Alloy, secrewed female parallel thread as per IS: 554, body having 1.5 MPa hydraulic pressure rating and Seat having 1.0 MPa hydraulic pressure rating. (screwed end). 25mm dia nominal bore.
Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to IS; 12701, colour opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support including fittings & fixtures for tank shall be paid separately. (Each tank of 500 liters capacity)
Providing and fixing in location MS Puddle Flange of the following diameters, having 'F' Table flanges at the inlet and outlet, and 'D' Table Puddle in the center with double welded joints, made of 150mm NB MS Pipe, tying the puddle with the Re-inforcement steel in the RCC walls at construction stage and in coordination with the structure engineers' designs, at the location as mentioned in the plumbing layouts. Size: 150mm diameter
Providing and fixing in location GI Threaded Flange of the following diameters, having 'E' Table threaded flanges at the inlet and outlet, and 'D' Table threaded puddle in the center with threading of pipes as required, made of 100mm NB GI (Medium Duty) Pipe, tying the puddle with the Re-inforcement steel in the RCC walls at construction stage and in coordination with the structure engineers' designs, at the location as mentioned in the plumbing layouts. Size: 100mm diameter
Providing and fixing in location GI Threaded Flange of the following diameters, having 'F' Table threaded flanges at the inlet and outlet, and 'D' Table threaded puddle in the center with threadingof pipes as required, made of 80mm NB Medium Duty GI Pipe, tying the puddle with the Re-inforcement steel in the RCC walls at construction stage and in coordination with the structure engineers' designs, at the location as mentioned in the plumbing layouts. Size: 80mm diameter
Providing and fixing in location GI Puddle Flange of the following diameters, having 'F' Table flanges at the inlet and outlet, and 'D' Table Puddle in the center with double welded joints, made of 50mm NB MS / GI Pipe, tying the puddle with the Re-inforcement steel in the RCC walls at construction stage and in coordination with the structure engineers' designs, at the location as mentioned in the plumbing layouts. Size: 65mm diameter
Providing and fixing full thread G.I. Tank Nipple (medium duty) as per IS: 1239, including drilling holes in the tanks at required levels, inserting the coupling in place, sealing the hole with silicon sealant, attaching the hex nuts on either side of the coupling as directed and approved by the Engineer-in-charge. (C) 32mm diameter
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.1 - 1216 (16mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.2 - 1620 (20mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.3 - 2025 (25mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.4 - 2532 (32mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.5 - 3240 (40mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.6 - 4050 (50mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. Concealed Work, including cutting chases and making good the wall etc. - 18.2.1 - 1216 (16mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. Concealed Work, including cutting chases and making good the wall etc. - 18.2.2 - 1620 (20mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. Concealed Work, including cutting chases and making good the wall etc. - 18.2.3 - 2025 (25mm OD) pipe
Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. Concealed Work, including cutting chases and making good the wall etc. - 18.2.4 - 2532 (32mm OD) pipe
Providing and fixing chlorinated polyvinyl chloride (CPVC) Ball valves with S.S. 304 ball valve, having pressure bearing capacity up to 7.0 kg/cm² at 82°C, of the following sizes including cutting the pipes, solvent welding, complete as per the manufacturers standards and the direction of the Engineer-in-charge. Make: Astral / Supreme / Ashirvad. a) 20 mm nominal bore
Providing and fixing chlorinated polyvinyl chloride (CPVC) Ball valves with S.S. 304 ball valve, having pressure bearing capacity up to 7.0 kg/cm² at 82°C, of the following sizes including cutting the pipes, solvent welding, complete as per the manufacturers standards and the direction of the Engineer-in-charge. Make: Astral / Supreme / Ashirvad. b) 25 mm nominal bore
Providing and fixing chlorinated polyvinyl chloride (CPVC) Ball valves with S.S. 304 ball valve, having pressure bearing capacity up to 7.0 kg/cm² at 82°C, of the following sizes including cutting the pipes, solvent welding, complete as per the manufacturers standards and the direction of the Engineer-in-charge. Make: Astral / Supreme / Ashirvad. c) 32 mm nominal bore
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) / XLPE insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. a) For 15mm diameter pipes
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) / XLPE insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. a) For 20mm diameter
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. b) For 25mm dia pipes - 19mm x 28mm Nitrile Rubber Plain Tubing
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. c) For 32mm dia pipes - 25mm x 35mm Nitrile Rubber Plain Tubing
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. d) For 40mm dia pipes - 25mm x 42mm Nitrile Rubber Plain Tubing
Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. e) For 50mm dia pipes - 25mm x 54mm Nitrile Rubber Plain Tubing
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910, on 12mm dia steel bar conforming to IS: 1786, having minimum cross section as 23mm x 23mm and overall minimum length 263mm and width as 165mm with minimum 112mm space between protuded legs, having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to withstand the bend test and chemical resistance test as per specifications and having manufacturers' permanent identification mark to be visible even after fixing in tanks with 30 x 20 x 15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) complete as per design.
Providing & fixing C.I. Manhole cover 0.6 x 0.45 M size having weight not less than 35 kg.
Section 2: Sanitary Providing & fixing Divyang toilet set with European Closet (P Trap) & wall mount wash basin & all divyang requirements with dual flush tank, seat & cover (heavy duty) with C.P. brass hinges,including WC connector of 110mm inlet x 110mm outlet, connecting the same with soil pipe using appropriate solvent cement, C.I. Brackets for wall mounting the basin, 32mm CP waste Coupling, 32mm size CP bottle trap, CP brass Spatula Faucet, etc. all Internal fittings complete with S.S grab rails etc. rubber buffers, C.P nuts, bolts etc making holes in walls & floors, & finishing for ready to use.The rate includes all necessary connection charges as per product detail to the satisfaction and as directed by the Engineer-in-charge. Make: Hindware / Cera.
Providing and fixing white vitreous china extended wall mounting water closet of size 530 x 330 x 390mm of approved shape including seat and cover, nuts, bolts, and gaslets etc complete. Make: Hindware - Flora / Jaquar - Florentine / Cera - Campbell Clear Rim.
Providing and fixing UPVC SWR WC Connector 130 x 110 mm dia. Socket type of approved make, fixed to outlet gaskets with UPVC Lubricant or Solvent Cement, all complete as per directions of the Engineer-in-charge. Make: Astral; Model No. F172005909 or Equivalent.
Providing, fixing, testing & commissioning of Concealed cistern with frame with dual flush 3/6 ltr with wall flush plate of approved make including push fit flexible hose complete including cutting and making good the walls where required complete as directed by Engineer-in-charge.
Providing anf fixing wash down water closet (Indian type W.C. pan) with integral P or S trap including joiting the trap with soil pipe in cement mortar 1:1 (1 - cement: 1 - fine sand) (A) vitreous china pattern: (i) in white colour
Providing and fixing 100mm P or S trap for water closet squatting pan including jointing the the trap with the pan and soil pipe in cement mortar 1:1 (1 - cement: 1 - fine sand) (A) vitreous china.
Providing and fixing in cement mortar 1:3 (1 - cement: 3 - coarse sand) a pair of white vitreous china 250mm x 130mm 30mm footrest to long pattern squatting pan water closet.
Providing and fixing Flat Back Large Urinal or approved quality including conecting the Urinal with waste pipe , tap etc. complete.(A) White vitreous China flat back large urinal size (355 to 420)mm x (240 to 395)mm x (535 to 635)mm. Make: Hindware - Eureka / Jaquar - URS / Cera - Carmina.
Providing and fixing countertop / table top wash basin having 15mm single hole in the middle for faucet fitting and 38mm hole in the bottom of the bowl for grid drain, cutting and making good the holes in the counter / table top wherever required: (i) White Vitreous China Counter Top / Table Top Wash Basin size (450 to 550) x (300 to 470) mm.
Providing and fixing wall mount wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: 17.7.9 White Vitreous China Surgeon Type Wash Basin size 660x460 mm with a single 15mm C.P. brass pillar tap with elbow operated lever (ISI marked)
Providing and fixing white vitreous china bath tub of approved or equivalent make and size, as approved by Engineer-In-Charge, with CP rim mounted mixer,with over flow set, drain plug, complete, including cutting and making good the walls and floors, wherever required, all leads, lifts , levels and heights, including making all necessary connections all complete and as per the directions of EIC. Make: Bath Tub: Hindware / Cera.
Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen Sink without drain board: Size: 510 x 430mm bowl depth 200 mm.
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.2: Waste coupling 38mm dia of 83mm length and 77mm breadth, weighing not less than 60 gms.
Providing and fixing PTMT Bottle Trap for wash basin and sink, of approved quality and colour. 17.70.2: Bottle trap 38mm dia single piece moulded with height of 270mm, effective length of tail pipe 260mm from the center of the waste coupling, 77mm breadth with 25mm minimum water seal, weighing not less than 263 gms.
Providing and fixing 32mm CP Brass Full Thread Waste Coupling for wash basin, of approved quality and manufacturer's standards. Waste Coupling: 32mm dia of 83mm length, weighin not less than 60 gms.
Providing and fixing CP Brass Bottle Trap for wash basin, of size 250 x 190mm or nearabout, of approved quality and model. Bottle trap 32mm dia with height of 250mm, effective length of tail pipe 190mm from the center of the waste coupling, 77mm breadth with 25mm minimum water seal.
Providing and fixing ABS Chrome plated Brass Hand Shower (Health Faucet) of approved make and quality and as approved by Engineer - In - Charge, including 8 mm dia, 1 Meter long Flexible tube & wall hook including cutting and making good the walls wherever required complete as per directions of the Engineer-in-charge.
Providing and Fixing 15 mm dia. Wall mounted type CP brass pressmatic bib cock with Auto Closing System with Built-in Control Cock With Wall Flange complete, making all necessary connections etc. All complete as per directions of the Engineer-in-charge. i) 15mm dia.
Providing and fixing of 15mm nominal bore CP Brass Angle valve confirming to IS: 8931, for wash basins, water coolers, geyser points, etc of approved quality and as approved by and directed by the Engineer-in-charge.
Providing and Fixing 15 mm dia. CP brass two way bib cock with wall flange and ceramic disc cartridge complete, making all necessary connections etc. All complete as per directions of the Engineer-in-charge. i) 15mm dia.
Providing and Fixing in position 32mm CP brass Pressmatic WC (Metropole) Flush Valve Auto-closing system with built in Control Cock and Wall flange of approved or equivalent make, including 32mm UPVC pipe connection with WC, and including all necessary materials required for fixing. All complete as per directions of the Engineer-in-charge.
Providing and Fixing in position CP brass Pressmatic Urinal Flush Valve Auto-closing system with built in Control Cock and Wall flange of approved or equivalent make, including 15mm S.S. pipe connection with Urinal and Urinal Spreader, and including all necessary materials required for fixing. All complete as per directions of the Engineer-in-charge.
Providing and Fixing 15 mm dia. CP brass bib cock with Wall Flange complete, making all necessary connections etc. All complete as per directions of the Engineer-in-charge. i) 15mm dia.
Providing and Fixing 15 mm dia. Wall mounted type CP brass Sink cock with Wall Flange complete, making all necessary connections etc. All complete as per directions of the Engineer-in-charge. i) 15mm dia.
Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.
Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each
Providing and fixing C.P. brass Shower arm for over head shower of approved make and quality, and as approved by the Engineer-in-charge, and conforming to Manufacturers Standards. a) Size: Casted 190mm long light body round shape for wall mounted shower rose with flange, of approved make and as per the direction of the Engineer-in-charge.
Providing and fixing C.P. brass Single Lever Exposed Shower Mixer for exposed shower arm & Hand Shower , connecting legs & wall flanges, complete as per approved make and as directed by the Engineer-in-charge.
Providing and fixing Hand held Shower with 100mm round rose head single flow, with 1.5 meter flexible SS hose.
Providing and fixing PTMT grating of approved quality and colour: Rectangular type with openable circular lid: 150 mm nimnal size square 100 mm diameter of the inner hinged round grating.
Providing and fixing SS Toilet Paper Roll Holder with Flap including SS screws & Rawl Plugs, complete as per approved make and as directed by the Engineer-in-charge.
Providing and fixing SS Liquid Soap Dispenser with metallic bottle having 250ml liquid holding capacity of approved make and quality and as directed by the Engineer-in-charge.
Providing and fixing SS Floor Cleanout (FCO) plug of approved brand and with SS Square Frame/ Round Frame with Flat Round Cover with Rubber Seal & SS Screw jointing as per manufacturer recommendation or per approval of the Engineer-in-charge. ii) 128mm x 128mm Square Top for 100 mm dia pipe.
Providing and fixing U.P.V.C (Type B) conforming to IS 13592, & fittings conforming to IS 14735 of approved make Multi Floor Trap Height Riser with 50mm x 50mm x 75mm inlet x 110mm dia outlet, as per specifications & at all levels & at all heights, as approved and directed by Enigeer-in-charge.
Providing, laying and jointing in true line and level 160 mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing, laying and jointing in true line and level 110 mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing, laying and jointing in true line and level 75mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to IS 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing, laying and jointing in true line and level 50mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to IS 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Pipe length per piece: 1.8 Mtrs
Providing, laying and jointing in true line and level 40mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to IS 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing and fixing unplasticized PVC SWR as per IS: 13592 (Type B), P - Trap as approved and directed by the Engineer-in-charge. For 110 mm Dia pipe
Providing and fixing unplasticized PVC SWR as per IS: 13592 (Type B), vent cowl as approved and directed by the Engineer-in-charge. For 75 mm Dia pipe
Providing and fixing unplasticized PVC SWR as per IS: 13592 (Type B), vent cowl as approved and directed by the Engineer-in-charge. For 110 mm Dia pipe
Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type A) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised-PVC rain water pipes conforming to IS : 13592 (Type A), including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe Bend - 110mm dia pipe
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes at an average distance of 1.2 meters centre to centre, by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
Providing and fixing unplasticised -PVC corner gully trap of size 200mm long x 200mm wide , having 80x80x115 mm vertical connection for 75mm diameter pipe, of approved design as per IS: 14735, to unplasticised - PVC SWR (Type A) pipes at all floors and all levels as indicated in the drawings, within the floor bedding, including cutting floors and walls as required, and making good the floors and walls etc. complete as per the direction of the Engineer-in-charge.
Providing and fixing G.I. Rainwater spout of 50mm diameter and 30 cm length.
Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type A) conforming to IS 13592 with one end plain and other end socketed with rubber ring, for drainage system pipe line in FFTG and HVAC shafts, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 80 mm diametre x 149 mm length x 145 mm height at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.
Sec.3.0 SEWAGE Providing and fixing cast iron steps of size 500 mm x 150mm x 22.5 mm and painting with two coats of Anti-corrosive paint etc. complete.
Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and watertight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight. (i) Squatre motuh traps. (B) 150mm x 100mm size P or R type.
Providing and laying (to level or slopes) and jointing reinforced concrete light duty non-pressure pipes as per IS: 458, Class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. (B) 150mm (up to 10 ton)
Providing and laying (to level or slopes) and jointing reinforced concrete light duty non-pressure pipes as per IS: 458, Class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. (C) 250mm (upto 10 ton)
Supplying and fixing reinforced concrete heavy duty nonpressure pipes with collars for culverts carrying heavy traffic as per IS 458 specifications including setting the pipes in C.M. 1:2 watering and laying (to level or slopes) of class NP3 of following internal diameters (i) 300mm dia. (up to 10 ton)
Constructing brick masonry chamber for underground C.I. Inspection Chamber and bends with bricks having crushing strength not less than 35 kg / cm2 in CM 1:5, C.I. cover with frame (Lgith duty) 455mm x 610mm internal dimensions total weight of cover and frame to be not less than 38 kg. (wt. of cover 23 kg and Wt. of frame 15 kg) with R.C.C. top slab in 1:2:4 mix (1 - cement; 2 - coarse sand; 4 - graded stone aggregate 20mm nominal size) foundation concrete in mix 1:5:10 (1 - cement; 5 - coarse sand; 10 - graded stone aggregate 40mm nominal size) with inside palster 15mm thick with cement mortar 1:3 (1 - cement; 3 - fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete. (ii) Inside dimensions 500mm x 700mm and 450mm deep for pipeline with one or two inlets. (up to 10 ton)
Extra over items 351 for every additional depth of 0.1M or part thereof beyond 450mm depth for brick masonry chamber (ii) for 500mm x 700mm size.
Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1 - cement; 2 - coarse sand; 4 - graded stone aggregate 20mm nominal size) foundation concrete in 1:3:6 mix (1 - cement; 3 - coarse sand; 6 - Brick bats 40 to 50mm size) inside plastering 15mm thick with cement moratar 1:5 (1 - cement; 5 - coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 - cement; 2 - coarse sand; 4 - graded stone aggregate 20mm nominal size) finished smooth complete, including curing and festing (i) inside size 900mm x 1200mm and 1.5M deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs (Wt. of cover 64 kgs. and Wt. of frame 64 kgs.) (A) with 230mm thick walls of brick masonry using brick having crushing strength not less than 35 kg. / Sq. Cm. in cement mortar 1:5 mix (1 - cement; 5 - coarse sand) (1) A type depth 0.90 meter.
Extra rate for constructing B.B. masonry for every additional depth of 0.1M or part thereof over item no. 353 (I) for depth from 1.50M to 2.25M
Sec.4.0 DRAINAGE Providing and fixing cast iron steps of size 500 mm x 150mm x 22.5 mm and painting with two coats of Anti-corrosive paint etc. complete.
Providing and laying (to level or slopes) and jointing reinforced concrete light duty non-pressure pipes as per IS: 458, Class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete. (C) 250mm (upto 10 ton)
Supplying and fixing reinforced concrete heavy duty nonpressure pipes with collars for culverts carrying heavy traffic as per IS 458 specifications including setting the pipes in C.M. 1:2 watering and laying (to level or slopes) of class NP3 of following internal diameters (i) 300mm dia. (up to 10 ton)
Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1 - cement; 2 - coarse sand; 4 - graded stone aggregate 20mm nominal size) foundation concrete in 1:3:6 mix (1 - cement; 3 - coarse sand; 6 - Brick bats 40 to 50mm size) inside plastering 15mm thick with cement moratar 1:5 (1 - cement; 5 - coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 - cement; 2 - coarse sand; 4 - graded stone aggregate 20mm nominal size) finished smooth complete, including curing and festing (i) inside size 900mm x 1200mm and 1.5M deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs (Wt. of cover 64 kgs. and Wt. of frame 64 kgs.) (A) with 230mm thick walls of brick masonry using brick having crushing strength not less than 35 kg. / Sq. Cm. in cement mortar 1:5 mix (1 - cement; 5 - coarse sand) (1) A type depth 0.90 meter.
Extra rate for constructing B.B. masonry for every additional depth of 0.1M or part thereof over item no. 353 (I) for depth from 1.50M to 2.25M
Percolation Wells: 6 numbers (in site) Boring / drilling bore well of required diameter for casing / strainer pipe, by suitable method prescribed in IS: 2800 (part 1), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per the direction of Engineer-in-charge, up to 90 meter depth below ground level. All types of Soil. 300 mm Dia
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per the direction of Engineer-in-charge. 200 mm nominal size diameter
Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per the direction of Engineer-in-charge.
Supplying, filling, spreading & levelling gravels of size range 5 cm to 10 cm, in recharge pit, over the existing layer of boulders, in the required thickness, for all leads & lifts, all complete as per the direction of Engineer-in-charge.
Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm, in recharge pit, over gravel layer, in the required thickness, for all leads & lifts, all complete as per the direction of Engineer-in-charge.
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine / medium / coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
Providing and fixing factory made precast RCC perforated drain covers, havng concrete of strength not less than M-25, of size 1000 x 450 x 50 mm, reinforced with 8 mm Dia four numbers of logitudinal & 9 numbers cross sectional T.M.T. hoop bars, including providing 50 mm diameter perforations @ 100 to 125 mm centre to centre, including providing edge bridging with M.S. flats of size 50 mm x 1.6 mm complete, all as per the direction of Engineer-in-charge.
Sec.5.0 MECHANICALS Hydro-pneumatic System - for Soft Water: Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted Hydropneumatic System as follows: Design, engineer, procure, supply, test and commission a pre-engineered, factory fabricated, assembled & tested, fully integrated, highly efficient pump, IE3 motors, skid mounted, complete ready-to-connect packaged variable speed water pressure booster station. The packaged variable speed water pressure booster station shall be complete with vertical multi stage centrifugal pumps connected in parallel, high efficiency IE 3 motors, an air-cooled external variable frequency drive, intelligent multi-pump controller, the controller shall be mounted in a control cabinet with an IP 67 enclosure of suitable rating having Potential free contacts to monitor On/Off & Trip status with necessary sensors/switches; Stainless Steel (SS 304) suction and delivery manifolds; isolation ball valves on suction and discharge of each pump; non return valve on discharge side of each pump; hot dip galvanised common base frame; and diaphragm pressure vessel. Complete (Skid mounted / wall mounted / floor mounted) electrical control panel comprising of all accessories such as PLCs, pressure switches, pressure transducers, control wiring and any other necessary imports etc. (list to be provided by the vendor). All installations such as electrical wiring from Electrical Panel to Pump panel, civil foundations, etc is included in this scope. Set of accessories such as NRVs, isolating valves, Stainless Steel (SS 304) suction and delivery header, pressure gauge, MS Epoxy coated base frame, pressure switches, pressure transducers, inter connecting power and control cabling etc. complete. For Soft Water: Soft Water Supply - Set consisting of 3 pumps (2 working + 1 standby); Flow Rate (System): 334 LPM (20.04 Cu. Mtr / Hr); Pressure Vessel = 1 x 200 Ltrs; Head (each pump): 75 Mtrs.
Submersible Pumps for Recycled Water: Supply, Installation, Testing and Commissioning of open well vertical multi stage (submersible) pump set with Stainless-steel body, C.I. Bearings, Stainless-steel motor shaft, Stainless-steel impeller, scope also includes the Star-Delta / Soft Start starter panels, cables/wires to the pumps, the pump controller shall be mounted in a control cabinet with an IP 67 enclosure of suitable rating having Potential free contacts to monitor On/Off & Trip status with necessary sensors / switches, complete for one / three phase submersible motor having the following discharge capacity and head: Recycled Water Transfer from STP to Roof Tank: No. of Pumps: 2 (1W + 1S); System Flow: 300 LPM (18 cum / hr); Head: 75 Mtrs.
Hydro-pneumatic System - for Soft Water - at all Terraces: Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted Hydropneumatic System as follows: Design, engineer, procure, supply, test and commission a pre-engineered, factory fabricated, assembled & tested, fully integrated, highly efficient pump, IE3 motors, skid mounted, complete ready-to-connect packaged fixed speed water pressure booster station. The packaged fixed speed water pressure booster station shall be complete with vertical multi stage centrifugal pumps connected in parallel, high efficiency IE 3 motors, intelligent multi-pump controller, the controller shall be mounted in a control cabinet with an IP 67 enclosure of suitable rating having Potential free contacts to monitor On/Off & Trip status with necessary sensors/switches; Stainless Steel (SS 304) suction and delivery manifolds; isolation ball valves on suction and discharge of each pump; non return valve on discharge side of each pump; hot dip galvanised common base frame; and diaphragm pressure vessel. Complete (Skid mounted / wall mounted / floor mounted) electrical control panel comprising of all accessories such as PLCs, pressure switches, pressure transducers, control wiring and any other necessary imports etc. (list to be provided by the vendor). All installations such as electrical wiring from Electrical Panel to Pump panel, civil foundations, etc is included in this scope. Set of accessories such as NRVs, isolating valves, Stainless Steel SS 304 suction and delivery header, pressure gauge, MS Epoxy coated base frame, pressure switches, pressure transducers, inter connecting power and control cabling etc. complete. For Soft Water: Soft Water Supply - Set consisting of 2 pumps (1 working + 1 standby); Flow Rate (System): 150 LPM (9 Cu. Mtr / Hr); Pressure Vessel = 1 x 50 Ltrs; Head (each pump): 25 Mtrs.
Water Treatment Plant: Supply, Installation, Testing and Commissioning of water treatment plant having Activated Carbon filters, Multi-grade / Pressurized Sand filters, Softeners including resin & salts, Resin Treament, Anti-scalant treatment, or any of these in a combination to provide scaling free water to all buildings within the campus, including centrifugal multistage water pump (1 working + 1 standby), connected plumbing work, control panel for auto cutoff, auto on, auto regeneration, auto rinse and auto filter mode with IP55 protection with all necessary equipment, piping and connected activities as per specification and operating conditions as mentioned by manufacturer or as directed by engineer in charge. System Capacity: 88,000 litres per day.
Hot Water Plant: Supplying, installing, testing and commissioning of Electrically Operated Air-to-Water Heat Pump Hot Water System capable of producing Hot water up to 60°C, at ambient temperature of 12°C to 55°C. Heat pump should have an IPX4 compatible control panel, designed and built in manufacturer's factory and compliant to norms for the same and compatible to support 9 units in parallel. Inbuilt 4 Ways valve for auto defrost function. The heat pump shall have an operational noise level of less than or equal to 65 dB(A). Model should be with tube in tube type heat exchanger Comprising of helical rotary twin compressors with direct drive motor (the compressor speed shall not exceed 3000 RPM) with shell and tube type plain tube chiller as well as shell & insulated tube type integrally finned condenser, at working efficiency of minimum 80%, having heating capacity up to 60 degree centigrade, capable to withstand up to 500 ppm water hardness. The heat pump package shall include vibration mountings, copper refrigerant piping as per the latest applicable B.I.S. codes and standards, full refrigerant charge using CFC free gas, system control wiring and accessories, installed on a fabricated mild steel base frame assembled to form a compact assembly, complete with micro-processor based control panel comprising of adaptive controls, indication lights, Star-Delta starters, over-load and under-load protection, TPN isolator for termination of incoming power cable, necessary control wiring, disconnect switch, grooved (Victaulic couplings at inlet and outlet of both heat exchangers, DP switches for both heat exchangers, vibration isolation arrangements electrical panel with starter for Heat Pumps, testing of all systems post installation at Minimum Wet Bulb Temperature of 17.7 degree Celsius in January to deliver hot water at 55 degree Celsius. The scope also includes commissioning of the entire system, commissioning certificate in the name of the Engineer-in-charge, etc. complete as per manufacturing standards and to the complete satisfaction of the Engineer-in-charge. The scope includes pre-insulated S.S. storage tanks or M.S. storage tanks with ceramic lining, of capacity as mentioned below, including making inlet, outlet heavy gauge C.P. connection, temperature guages (at inlet and outlet of storage tank). The Storage Tanks duly painted with two coats of Red-Oxide and having PUF / Rockwool insulation, outer cladding of 22 guage Aluminum Sheet, control valves at inlet and outlet of Water tank, M.S. supports for the tanks with M.S. base plate, bolts and nuts for fastening the stands and support to Cement concrete blocks, testing the tanks and the entire hot water system at a constant water pressure of 5.0 Bar (Hyd.) each, testing of the entire system for a constant flow of hot water at 60 degree Celcius during peak winter when the Wet Bulb Temperature is 17.7 degree Celcius. FOR HOSTEL BLOCK: Total System Capacity: 6000 LPD; Pre-insulated Hot Water Storage Tank with multiple inlets and outlets: 6000 Ltrs.; Heat Pump HWS: 2 sets, electrical starter panels, level sensors, temperature sensors, thermostat, temperature gauges, pressure gauge, interconnecting G.I. 'C' class pipes with nitrile rubber cladding and aluminium cladding, complete.
Hot Water Plant: Supplying, installing, testing and commissioning of Electrically Operated Air-to-Water Heat Pump Hot Water System capable of producing Hot water up to 60°C, at ambient temperature of 12°C to 55°C. Heat pump should have an IPX4 compatible control panel, designed and built in manufacturer's factory and compliant to norms for the same and compatible to support 8 units in parallel. Inbuilt 4 Ways valve for auto defrost function. The heat pump shall have an operational noise level of less than or equal to 65 dB(A). Model should be with tube in tube type heat exchanger Comprising of helical rotary twin compressors with direct drive motor (the compressor speed shall not exceed 3000 RPM) with shell and tube type plain tube chiller as well as shell & insulated tube type integrally finned condenser, at working efficiency of minimum 80%, having heating capacity up to 60 degree centigrade, capable to withstand up to 500 ppm water hardness. The heat pump package shall include vibration mountings, copper refrigerant piping as per the latest applicable B.I.S. codes and standards, full refrigerant charge using CFC free gas, system control wiring and accessories, installed on a fabricated mild steel base frame assembled to form a compact assembly, complete with micro-processor based control panel comprising of adaptive controls, indication lights, Star-Delta starters, over-load and under-load protection, TPN isolator for termination of incoming power cable, necessary control wiring, disconnect switch, grooved (Victaulic couplings at inlet and outlet of both heat exchangers, DP switches for both heat exchangers, vibration isolation arrangements electrical panel with starter for Heat Pumps, testing of all systems post installation at Minimum Wet Bulb Temperature of 17.7 degree Celsius in January to deliver hot water at 60 degree Celsius. The scope also includes commissioning of the entire system, commissioning certificate in the name of the Engineer-in-charge, etc. complete as per manufacturing standards and to the complete satisfaction of the Engineer-in-charge. The scope includes pre-insulated S.S. storage tanks or M.S. storage tanks with ceramic lining, of capacity as mentioned below, including making inlet, outlet heavy gauge C.P. connection, temperature guages (at inlet and outlet of storage tank). The Storage Tanks duly painted with two coats of Red-Oxide and having PUF / Rockwool insulation, outer cladding of 22 guage Aluminum Sheet, control valves at inlet and outlet of Water tank, M.S. supports for the tanks with M.S. base plate, bolts and nuts for fastening the stands and support to Cement concrete blocks, testing the tanks and the entire hot water system at a constant water pressure of 5.0 Bar (Hyd.) each, testing of the entire system for a constant flow of hot water at 55 degree Celcius during peak winter when the Wet Bulb Temperature is 17.7 degree Celcius. FOR 3 BHK Residential: Total System Capacity: 1440 LPD; Pre-insulated Hot Water Storage Tank: 1400 Ltrs.: Heat Pump HWS: 1 set, electrical starter panels, level sensors, temperature sensors, thermostat, temperature gauges, pressure gauge, interconnecting G.I. 'C' class pipes with nitrile rubber cladding and aluminium cladding, complete.
Hot Water Plant: Supplying, installing, testing and commissioning of Electrically Operated Air-to-Water Heat Pump Hot Water System capable of producing Hot water up to 60°C, at ambient temperature of 12°C to 55°C. Heat pump should have an IPX4 compatible control panel, designed and built in manufacturer's factory and compliant to norms for the same and compatible to support 8 units in parallel. Inbuilt 4 Ways valve for auto defrost function. The heat pump shall have an operational noise level of less than or equal to 65 dB(A). Model should be with tube in tube type heat exchanger Comprising of helical rotary twin compressors with direct drive motor (the compressor speed shall not exceed 3000 RPM) with shell and tube type plain tube chiller as well as shell & insulated tube type integrally finned condenser, at working efficiency of minimum 80%, having heating capacity up to 60 degree centigrade, capable to withstand up to 500 ppm water hardness. The heat pump package shall include vibration mountings, copper refrigerant piping as per the latest applicable B.I.S. codes and standards, full refrigerant charge using CFC free gas, system control wiring and accessories, installed on a fabricated mild steel base frame assembled to form a compact assembly, complete with micro-processor based control panel comprising of adaptive controls, indication lights, Star-Delta starters, over-load and under-load protection, TPN isolator for termination of incoming power cable, necessary control wiring, disconnect switch, grooved (Victaulic couplings at inlet and outlet of both heat exchangers, DP switches for both heat exchangers, vibration isolation arrangements electrical panel with starter for Heat Pumps, testing of all systems post installation at Minimum Wet Bulb Temperature of 17.7 degree Celsius in January to deliver hot water at 55 degree Celsius. The scope also includes commissioning of the entire system, commissioning certificate in the name of the Engineer-in-charge, etc. complete as per manufacturing standards and to the complete satisfaction of the Engineer-in-charge. The scope includes pre-insulated S.S. storage tanks or M.S. storage tanks with ceramic lining, of capacity as mentioned below, including making inlet, outlet heavy gauge C.P. connection, temperature guages (at inlet and outlet of storage tank). The Storage Tanks duly painted with two coats of Red-Oxide and having PUF / Rockwool insulation, outer cladding of 22 guage Aluminum Sheet, control valves at inlet and outlet of Water tank, M.S. supports for the tanks with M.S. base plate, bolts and nuts for fastening the stands and support to Cement concrete blocks, testing the tanks and the entire hot water system at a constant water pressure of 5.0 Bar (Hyd.) each, testing of the entire system for a constant flow of hot water at 60 degree Celcius during peak winter when the Wet Bulb Temperature is 17.7 degree Celcius. FOR 2BHK Residential Block: Total System Capacity: 1200 LPD; Pre-insulated Hot Water Storage Tank: 1200 Ltrs.; Heat Pump HWS: 1 set, electrical starter panels, level sensors, temperature sensors, thermostat, temperature gauges, pressure gauge, interconnecting G.I. 'C' class pipes with nitrile rubber cladding and aluminium cladding, complete.
Hot Water Plant: Supplying, installing, testing and commissioning of Electrically Operated Air-to-Water Heat Pump Hot Water System capable of producing Hot water up to 60°C, at ambient temperature of 12°C to 55°C. Heat pump should have an IPX4 compatible control panel, designed and built in manufacturer's factory and compliant to norms for the same and compatible to support 8 units in parallel. Inbuilt 4 Ways valve for auto defrost function. The heat pump shall have an operational noise level of less than or equal to 65 dB(A). Model should be with tube in tube type heat exchanger Comprising of helical rotary twin compressors with direct drive motor (the compressor speed shall not exceed 3000 RPM) with shell and tube type plain tube chiller as well as shell & insulated tube type integrally finned condenser, at working efficiency of minimum 80%, having heating capacity up to 60 degree centigrade, capable to withstand up to 500 ppm water hardness. The heat pump package shall include vibration mountings, copper refrigerant piping as per the latest applicable B.I.S. codes and standards, full refrigerant charge using CFC free gas, system control wiring and accessories, installed on a fabricated mild steel base frame assembled to form a compact assembly, complete with micro-processor based control panel comprising of adaptive controls, indication lights, Star-Delta starters, over-load and under-load protection, TPN isolator for termination of incoming power cable, necessary control wiring, disconnect switch, grooved (Victaulic couplings at inlet and outlet of both heat exchangers, DP switches for both heat exchangers, vibration isolation arrangements electrical panel with starter for Heat Pumps, testing of all systems post installation at Minimum Wet Bulb Temperature of 17.7 degree Celsius in January to deliver hot water at 60 degree Celsius. The scope also includes commissioning of the entire system, commissioning certificate in the name of the Engineer-in-charge, etc. complete as per manufacturing standards and to the complete satisfaction of the Engineer-in-charge. The scope includes pre-insulated S.S. storage tanks or M.S. storage tanks with ceramic lining, of capacity as mentioned below, including making inlet, outlet heavy gauge C.P. connection, temperature guages (at inlet and outlet of storage tank). The Storage Tanks duly painted with two coats of Red-Oxide and having PUF / Rockwool insulation, outer cladding of 22 guage Aluminum Sheet, control valves at inlet and outlet of Water tank, M.S. supports for the tanks with M.S. base plate, bolts and nuts for fastening the stands and support to Cement concrete blocks, testing the tanks and the entire hot water system at a constant water pressure of 5.0 Bar (Hyd.) each, testing of the entire system for a constant flow of hot water at 55 degree Celcius during peak winter when the Wet Bulb Temperature is 17.7 degree Celcius. FOR KITCHEN BLOCK: Total System Capacity: 9000 LPD; Pre-insulated Hot Water Storage Tank: 9000 Ltrs.; Heat Pump HWS: 1 set, electrical starter panels, level sensors, temperature sensors, thermostat, temperature gauges, pressure gauge, interconnecting G.I. 'C' class pipes with nitrile rubber cladding and aluminium cladding, complete.
Electric Geysers: Supplying and erecting horizontal / vertical mounting type storage water heater with copper container housed in M.S./S.S. body insulated with glass wool / puff complete with heating elements,adjustable thermostats 300 c to 850 C, indicating lamp, safety valve, fusible plug, etc.complete erected with coach bolts, nuts. washers & cementation. (B)15 Ltr-.with 2 /3K.W. heating element - Cat II Make: Racold or Similar or Equivalent of an approved make.
Supplying and erecting chromium plated heavy duty brass valve for inlet pipe of water heater 15 mm dia.)
Supplying and erecting 15mm brass non-return valve for inlet pipe of storage water heater.
Supplying and erecting dead pressure releasing valve for storage type water heater with necessary materials.
R.O. Plant: Supply, Installation, Testing and Commissioning of Reverse Osmosis water treatment plant having basket filter, Micro-cartridge filters, R.O. membranes, for providing purified drinking water to all buildings within the campus, including centrifugal multistage water pump (1 working + 1 standby) as per design requirement, connected plumbing work, control panel for auto cutoff, auto on, auto regeneration, auto rinse and auto filter mode with IP67 protection with all necessary equipment, piping and connected activities as per specification and operating conditions as mentioned by manufacturer or as directed by engineer in charge. System Capacity: RO - 400 LPH (Permeate) ; Feed – 0.6 m3/hr @ 70 - 80% recovery with drinking water parameters as mentioned in relevant codes and standards. Operating pressure: 10 – 12 Bar
Domestic R.O. Plant: Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [A] 10 Ltr / Hr with 7 Ltr Plastic Pressure Tank
WATER COOLERS: Providing and erecting water cooler having storage capacity 150Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45 deg. C. The outlet temp. of the water should drop by 15 deg. C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.
WATER COOLERS: Conveyance charges including loading / unloading for Water Cooler from store to site (I) Local up to 10 Km
LEVEL SENSORS: Supplying & erecting approved make Automatic liquid level controller 6A.as per instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper conductor from pump to upper and lower tank.
Sewage Treatment Plants: Supply, installation, testing & commissioning of Sewage Treatment Plant MBBR Type (Package Treatment Plant) of 85 kLD with collection tank, primary, secondary & tertiary treatment also with all electromechanical equipments, interconnected piping, valves, pumps, instruments, gauges, electrification like panel, starter, cabling, earthing, pH correction dosing system, aeration blowers, feed pumps, clarifiers, hypo dosing, coagulant dosing, flocculant dosing, sludge recirculation pumps, & tertiary treatment including multi-grade filter, activated carbon filter, 38 kLD Ultra-filtration, also with all electromechanical equipments, interconnected piping, valves, pumps, instruments, gauges, electrification like panel, starter, cabling, earthing, etc. complete. The sizing of tank/equipment shall take care of average as well as peak flow. The outlet parameters shall be as per specifications.(Including civil cost of Bar Screen Chamber) (Cost of civil works for tanks not included). The entire system shall be installed, all relevant approvals from local and other authorities to be procured, submitting of the reports, certificates, etc as per norms and requirements, training of staff, handing over all relevant documents, etc complete as directed and approved by the Engineer-in-charge.
DRAINAGE SUMP PUMP: Providing and fixing compact monoblock dry motor submersible pumps of suitable rating, with non-clog free flow open impeller, solid handling capacity of up to at least 30mm suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, M.S. galvanized lifting chain, duck foot bend complete. The pump sets shall be supplied with required accessories & as per specification with the following : (a) Water level sensing – switch type or hydraulic floats or pressure switch – with data accessible on IBMS platforms. (a) Complete piping 80 mm dia common delivery up to 12 m in heavy Duty Class 'C' G.I. – 10 meters length. (c) 80 mm dia Flap type Forged Brass Non-return valve. – 2 Nos. (d) 80mm dia Forged Brass Gate Valve. – 1 No. (e) Necessary cables from pump set to control panel (10 meters) – 1 Set (f) Electrical control panel having all necessary accessories & safety devices of standard specifications and suitable for receiving supply cable to connections within, and outlet connections for starters, and earthing outlets, complete. All best standards, as per ECBC & IS Codes to be followed and provided. Starters to be operated on cascading operations, so as to maintain maximum life cycle of each pump. – 1 Set. (g) Panels to have Modbus / BACnet connectivity, with pump performance data, pump fault data, On / Off operations, etc to be incorporated. (h) Each set consist of 2 nos. of pumps - 1 working & 1 stand by. Discharge: 25 Cu. Mtr / Hr. Head: 15 Meter (minimum).
SEC03 -ELECTRICAL WORKS ELW 01.00 HT G.O.D Supplying, Installation,Testing & Commissioning of HT DP Structure with necessary civil works as per specification and Details given below. a) 1 set of 11 kV Double pole MS structure (10 meters) b) 3 Nos. 9kV Gapless Lightning Arresters c) 1 no. 400 Amps GOD d) 1 set DO fuses e) 1 set of MS Channel (ISMC 75X40) supports f) 1 Set of Pin Insulators (as required) g) 1 set of Disc insulators (as required) h) 1 set of Stay wire (as required) i) ACSR DOG conductor with Raychem insulation tap (as required) j) other accessories & hardware to make system complete in all respect as per standard design practice and CEIG norms.
Leveling & rubble soiling the switchyard and ground with 1" size metal for a height of 150 mm from ground level for 6 x 6 mtr area complete in all respect as directed by engineer in charge.
SITC of Chain link fencing 50 x 50 mm Square of 10 SWG GI wire,2m height with gate for switchyard of 10 x 6 m and Runs of barbed wire above complete in all respect as directed by engineer in charge
ELW 02.00 HT RMU / HT PANEL Supplying, Installtion,Testing & Commissioning of outdoor duty SF6 insulated RMU with 2 nos.400A HT Load breakswitch & 1 no tapoff 400A VCB with CT & PT & lockable metering compartment as per supply company guideline.The panel should have tinned copper busbars . This should be complete with metering and protection and complete in all as per specification. - (For Supply company Metering)
Supplying, Installtion,Testing & Commissioning of 1 no.400A HT VCB as incomer and 2 nos 400A HT VCB as outgoings .The panel should have tinned copper busbars and extensible type for future requirements. This should be complete with metering and protection and complete in all as per specification. - (For Client side)
Supplying, Installtion,Testing & Commissioning of 1 no.800A HT VCB as incomer and 2 nos 400A HT VCB as outgoings .The panel should have tinned copper busbars and extensible type for future requirements. This should be complete with metering and protection and complete in all as per specification. - (For Client side)
ELW 03.00 Transformer Supplying, Installtion,Testing, Commissioning & unloading at site, shifting to the erection site assembling, leveling, grouting, installing, field testing and commissioning of 500KVA Dry type Transformer with on load tape chagner with OLTC and RTCC. Scope also includes connection between OLTC and RTCC. Complete in all respect as per specification.
ELW 03.00 Transformer Supplying, Installtion,Testing, Commissioning & unloading at site, shifting to the erection site assembling, leveling, grouting, installing, field testing and commissioning of 750KVA Dry type Transformer with on load tape chagner with OLTC and RTCC. Scope also includes connection between OLTC and RTCC. Complete in all respect as per specification.
ELW 04.00 Substation Equipment and substaion Auxiliary SITC of 11 KV, 3 core Al. 240 sqmm H.T. XLPE armoured unearth cable.
SITC of H.T. cable indoor type end connection for 11 KV XLPE, 240 sq mm x 3 core cable with all accessories including lugs
Suppplying & Erecting automatic emergency light with maintenance free battery for 2 X 18 watts CFL tube. With exide make battery
Supplying & Erecting Rubber mat 3.3 KV grade ISI marked 1000 x 2000 x 2 mm size As per IS 15652 Class-A.
Supplying & Erecting Rubber mat 11 KV grade ISI marked 1000 x 2000 x 2.5 mm size As per IS 15652. Class-B.
Providing and erecting danger notice board for medium voltage installation to be erected as per I.S. The board should be 150 x 150 mm.
Providing and erecting danger notice board for high voltage installation to be erected as per I.S.
Providing and fixing printed instruction chart both in English & REGIONAL LANGUAGE & duly framed out on glass for treatment of person suffering from Electric shock.
Providing pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.
Supplying and fixing Standard First aid box with all the Standard contents.
Supplying and instaling FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and Red out side with FIRE mark, filled with dry-sand and kept on existing stand provided or hung on wall hook..
Supplying & Erecting 1.5 mtr. (5') x 0.9 mtr. (3.1') x 0.6 mtr. (2.1') Floor mounted stand (For keeping 4 Nos.of buckets) made of 30 x 30 x 4 mm. angle iron welded with 4 hooks and duly painted with one coat of red lead & two coats of Approved enameled silver paints.
Supply installation testing and commissionning of Wall hooks of 22 to 25 cms. projection for keeping fire buckets made out of 15 mm. dia M.S. rod grouted in wall to a depth of minimum 15 cms.
ELW 05.00 MV Switch Gear and power Panel Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect MAIN LT POWER PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect 250KVAR APFCR PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect UTILITY PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect EXTERNAL LIGHTING PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect ACADEMIC BLOCK POWER PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect ACADEMIC BLOCK UPS PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect ACADEMIC BLOCK LIGHTING PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect ACADEMIC BLOCK HVAC PANEL-OUTDOOR TYPE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL BLOCK POWER PANEL-TOP SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL BLOCK UPS PANEL-TOP SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL TERRACE PLUMBING PANEL - OUTDOOR TYPE - TOP SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL ADMIN PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL BLOCK POWER PANEL-BOTTOM SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL BLOCK UPS PANEL-BOTTOM SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. HOSTEL TERRACE PLUMBING PANEL - OUTDOOR TYPE - BOTTOM SIDE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. CANTEEN POWER PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. CANTEEN UPS PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. CANTEEN HVAC PANEL - OUTDOOR TYPE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. CANTEEN TERRACE PLUMBING PANEL - OUTDOOR TYPE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 2BHK POWER PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 2BHK COMMON PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 2BHK TERRACE PLUMBING PANEL - OUTDDOR TYPE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 3BHK POWER PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 3BHK COMMON PANEL As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. 3BHK TERRACE PLUMBING PANEL - OUTDDOR TYPE As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. PRINCIPLE BUNGALOW As per Single line diagram
Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. PLUMBING+STP PANEL As per Single line diagram
ELW 06.00 DG Set with AMF panel Supplying, installation, testing and commissioning of DG set of 2 # 500 KVA with approximate 602 BHP engine with enclouser & suitable alternator complete with all necessary fuel piping,Aluminium cladding, exhaust piping, control panel, Auto synchronizing, auto load sharing AMF Panel, silencer & its piping, Acoustic silencer, Alternator cable termination box suitable for Aluminium cables,initial battery charging,base frame, battery and charger complete in all respect. Scope also includes preparing necessary drawing submitting to authorities, getting their approval / sanction and final certificate including NOC from pollution board(if required) to energize the D G Set . (Rate Includes 2 Nos. of 500 kVA Dg sets, 2 Nos. Control & AMF Panels and 1 No. of Auto synchronizing Panel etc. -Please refer Specification for Auto Sycn. Panel)
ELW 06.00 DG Set with AMF panel Supplying, installation, testing and commissioning of DG set of 750 KVA with approximate 902 BHP engine with enclouser & suitable alternator complete with all necessary fuel piping,Aluminium cladding, exhaust piping, control panel, Auto synchronizing, auto load sharing AMF Panel, silencer & its piping, Acoustic silencer, Alternator cable termination box suitable for Aluminium cables,initial battery charging,base frame, battery and charger complete in all respect. Scope also includes preparing necessary drawing submitting to authorities, getting their approval / sanction and final certificate including NOC from pollution board(if required) to energize the D G Set . (Rate Includes 750 kVA Dg sets, 1 Nos. Control & AMF Panels and 1 No. of Auto Panel etc. -Please refer Specification for Auto Panel)
ELW 07.00 Distribution Board DISTRIBUTION BOARD Supplying, assembling, grouting, levelling, installation, Connecting,testing and commissioning of D.B of specified make but without MCB / ELMCB/MCCB etc but with all internal busbar as per requirement. TPN Distribution Board : Supplying, erecting, testing and commissioning of only TPN D.B. with space for FPMCB as incoming and space for DPELMCB and 12 SPMCB as outgoing per phase (i.e. 16 way TPN D.B.) with 16 way PPI kit
Supplying, assembling, grouting, levelling, installation, Connecting testing and commissioning of D.B of specified make but without MCB / ELMCB/MCCB etc but with all internal busbar as per requirement. Supplying, erecting, testing and commissioning of only TPN D.B. with space for FPMCB as incoming and space for DPELMCB and 8 SPMCB as outgoing per phase (i.e. 12 way TPN D.B.) with 12 way PPI kit
Supplying, assembling, grouting, levelling, installation, Connecting testing and commissioning of D.B of specified make but without MCB / ELMCB/MCCB etc but with all internal busbar as per requirement. Supplying, erecting, testing and commissioning of only TPN D.B. with space for FPMCB as incoming and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way TPN D.B.) with 8 way PPI kit
SPN Distribution Board : Supplying, erecting, testing and commissioning of SPN D.B. with space for DPELMCB as incoming and 12 SPMCB as outgoing per phase (i.e. 16 way SPN D.B.)
Supplying, erecting, testing and commissioning of SPN D.B. with space for DPELMCB as incoming and 8 SPMCB as outgoing per phase (i.e. 12 way SPN D.B.)
Supplying, erecting, testing and commissioning of SPN D.B. with space for DPELMCB as incoming and 4 SPMCB as outgoing per phase (i.e. 8 way SPN D.B.)
Supplying, erecting, testing and commissioning of SPN D.B. suitable for outdoor mounting IP 65 with space for DPMCB as incoming and 2 SPMCB as outgoing (i.e. 4 way SPN D.B.) equivalent to Hensel make cat No.. KV 7104
MCB 's and its Accessories Supplying, Assembling, levelling, connecting testing and commissioning of following MCB / ELMCB / MCCB etc in boards as specified in 8.1, 8.2. Miniature circuit breaker single pole 1A to 32A. suitable to operate on 240V. A.C. system and having breaking capacity 10 KA to be erected in existing box. Confirming to IS 8828 / 1996 with ISI Mark.
16A /20A / 25A / 32 A DP ELCB (30mA)
40 A DP ELCB (30mA)
63 A DP ELCB (30mA)
16A /20A / 25A / 32A DP ELMCB(ELCB+MCB) (30mA)
40 A FP ELMCB(ELCB+MCB) (300mA)
6-32 A FP MCB
40A FP MCB
63A FP MCB
Sheet steel metal enclouser for SP MCB equivalent to Legrand cat No..607881
ShSheet steel metal enclouser for DP MCB equivalent to Legrand cat No...607882
Sheet steel metal enclouser for FP MCB equivalent to Legrand cat No...607884
SITC of Blank Plates
Caution Board : SITC of Caution boards of size 150 x 150 mm. to be supplied & fixed on the D.B.
ELW 8.00 CABLE TRENCH Excavation and back filling of cable trenches required for laying the cables / DWC Pipe directly buried in the ground. This includes supplying and providing cable markers at an interval of 10 meters. The depth shall be app. 0.9mtr and the width shall be as per requirement.
ELW 9.00 MV Cabling Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 240 Sq.mm x 3.5C Al. Cable
Supply, testing and Layingand commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 150 Sq.mm x 3.5C Al. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 95 Sq.mm x 3.5C Al. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 70 Sq.mm x 3.5C Al. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 50 Sq.mm x 3.5C Al. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 35 Sq.mm x 3.5C Al. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 10 Sq.mm x 4C CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 6 Sq.mm x 4c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 4 Sq.mm x 4c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 2.5 Sq.mm x 4c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 10 Sq.mm x 3c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 6 Sq.mm x 3c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 4 Sq.mm x 3c CU. Cable
Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 2.5 Sq.mm x 3c CU. Cable
ELW 10.00 Cable Termination SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 240 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 150 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 95 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 70 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 50 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 35 Sq.mm x 3.5C Al. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 10 Sq.mm x 4C CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 6 Sq.mm x 4C CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 4 Sq.mm x 4C CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 2.5 Sq.mm x 4C CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 10 Sq.mm x 3c CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 6 Sq.mm x 3c CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 4 Sq.mm x 3c CU. Cable
SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 2.5 Sq.mm x 3c CU. Cable
ELW 11.00 Cable Tray Supply, Installation, testing and commissioning of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 150 x 100 made out of 2 mm thick ladder type
Supply, Installation, testing and commissioning of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 300 x 100 made out of 2 mm thick ladder type
Supply, Installation, testing and commissioning of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 450 x 100 made out of 2 mm thick ladder type
Supply, Installation, testing and commissioning of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 600 x 100 made out of 2 mm thick ladder type
Supply, Installation, testing and commissioning of hot dip GI ladder type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 750 x 100 made out of 2 mm thick ladder type
Supply, Installation, testing and commissioning of hot dip GI perforated type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 150 x 100 made out of 2 mm thick perforated type
Supply, Installation, testing and commissioning of hot dip GI perforated type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 300 x 100 made out of 2 mm thick perforated type
Supply, Installation, testing and commissioning of hot dip GI perforated type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 450 x 100 made out of 2 mm thick perforated type
Supplying , fabricating and installation of various sizes clamps for cable tray supports using available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant including applying zinc chromate yellow oxide and two to three coats of required enamel paints with anchor fasteners etc.
ELW 12.00 Internal Wiring WITH MODULAR TYPE SWITCHES Wiring of points to be done in open/concealed manner in 25 mm dia medium guage Rigid PVC FRLS pipe. Wiring shall be done with FRLS type copper flexible wire of 650V/1100V. Separate pipe should be taken for circuit mains. Nos of ciruit of the same phases may be taken in same conduit .The circuit shall be laid in 25/40 mm dia medium guage rigid PVC FRLS pipe.The point rate shall include all the necessary piping and wiring from sub panel / Distribution board to switch board & switch board to the batten holder / angle holder / connector / ceiling rose all inclusive except sub panel / Dist board. The wiring shall be done as per relevant prevailing standard. The looping of the wiring should be done in the switch boxes or light and fan point outlet boxes to avoid the junction boxes. The junction boxes and switch boxes for the ceiling light point, fan point etc shall be minimum 60/75 deep. All the necessary jarry in brick plastered walls should be done with machine cutter only , also jarry should be filled with cement, sand and wire mesh as required, the material cost for rough finish shall be included in point rate.Whenever pipes are required to be laid in flooring shall be of.Wiring should be done as per distribtion details. Each circuit should have dedicated phase, neutral & earth wire. Wire sizes to be used as under For Light Points /fan point/ wall fan / 6A 3 Pin Plug - DB to SB - 2.5sqmm for Phase & Neutral & 1.5 sqmm for Earth - SB to on board Point - 1.5 sqmm for Phase & Neutral & Earth For 6A Plug point. - 1.5 sqmm for Phase, Neutral & Earth For 6/10/16A general purpose plug point - 2.5 sqmm for Phase, Neutral & 1.5 sqmm Earth For 16A plug point for A/C and Geyser - 4 Sqmm for Phase, Neutral & 2.5 sqmm Earth For 20/32A plug point - 6 sqmm for Phases, Neutral & 4 sqmm Earth No zarry will be allowed in expose brick work. The conduit shall be provided when the walls are under construction. The pipes in slab shall be laid before the slab is casted. One light point controlled by one single way 6 A switch.
Loop light point to be controlled from same switch.(Looping from first point)
One light point controlled by two, two way 6 A switch
One ceiling fan outlet point controlled by one 6 A switch and hum free electronic type step regulator and cast iron fan box.
One 6 A x 5 pin 250 Volt universal socket outlet point controlled by one 6 A switch located on switch board.
6 A x 5 pin 250 Volt universal switched socket outlet point at convenient location.
6/16 A x 250 V switch socket point on one switch box with 2.5 sqmm flexible wires and phase and neutral and 1.5 sq nm flexible Cu. wire as earth wire. The rate should include conduiting upto DB.
6/16A x 250 Volt switched socket outlet point for Equipment with 4 sq.mm wire for phase and neutral & 2.5 sq.mm earth wire.
Exhaust fan outlet point with 6A 5 pin socket controlled by one 5 single way switch located at different location.
Bell point controlled by Bell push switch with Buzzer / bell of approved make.
SITC computer power supply point with 2 nos of 6 amp 5 pin socket with 1 no. of 6/16 Amp. socket with 1 no 16 A Switch with indicator & wiring of computer point will be done through 2 nos.of 2.5 sq. mm Cu. wires as phase & Neutral and 1 nos. of 1.5 sq.mm.as earth wire. .( This cost includes the wiring from DB to Computer point.)
SITC of Outdoor Type 6/16A Socket with Switch, Suitable for outdoor appication (IP66)
20 A x 250 V plug & socket with interlocked switched socket, DP MCB and surface mounting box IP 66 with DIN rail for 2 module legrand make Cat no.56661 or equivalent but without cost of wiring and piping.
32 A x 250 V plug & socket with interlocked switched socket, DP MCB and surface mounting box IP 66 with DIN rail for 5 module legrand make Cat no.56669 or equivalent but without cost of wiring and piping.
32 A x 415 V plug & socket with interlocked switched socket, FP MCB and surface mounting box IP 66 with DIN rail for 5 module legrand make Cat no.56674 or equivalent but without cost of wiring and piping.
METAL CLAD SWITCJH SOCKET SITC of Metal Clad Switch Socket with 10A SP MCB (2P+E)
SITC of Metal Clad Switch Socket with 20A DP MCB (2P+E)
SITC of Metal Clad Switch Socket with 20A FP ELMCB (2P+E)
SITC of Metal Clad Switch Socket with 32A FP ELMCB (P+E)
MAINS SITC of mains with 4 nos. of 6 sq mm Cu. PVC insulated FRLS flexible wire with ISI approval for 650 V/ 1100 V and 2 nos 2.5 sqmm Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in 25 mm diameter rigid PVC conduit of medium guage having ISI and FIA approval with all necessary accessories.
SITC of mains with 2 nos. of 4 sq mm Cu. PVC insulated FRLS flexible wire with ISI approval for 650 V/ 1100 V and 1 no 4.0 sqmm Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in 25 mm diameter rigid PVC conduit of medium guage having ISI amd FIA approval with all necessary accessories.
SITC of mains with 2 nos. of 6 sq mm Cu. PVC insulated FRLS flexible wire with ISI approval for 650 V/ 1100 V and 1 no 4.0 sqmm Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in 25 mm diameter rigid PVC conduit of medium guage having ISI amd FIA approval with all necessary accessories.
SITC of mains with 2 nos. of 2.5 sq mm Cu. PVC insulated FRLS flexible wire with ISI approval for 650 V/ 1100 V and 1 no 2.5 sqmm Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in 25 mm diameter rigid PVC conduit of medium guage having ISI amd FIA approval with all necessary accessories.
SITC of mains with 2 nos. of 1.5 sq mm Cu. PVC insulated FRLS flexible wire with ISI approval for 650 V/ 1100 V and 1 no 1.5 sqmm Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth wires to be drawn in 25 mm diameter rigid PVC conduit of medium guage having ISI amd FIA approval with all necessary accessories.
Supplying , fabricating and installation of various sizes junction boxes made out to 14 gauge sheet with all necessary accessories & hardware etc All the necessary fabrication required will be included in the scope of contractor. Scope also includes two coat of primer and two coat of paining of each items on all the sides complete in all respect.
Supply and installation of GI Trunking made up of Pre Galvanized sheet metal with zinc coated steel sheet double folded and arc welded. The double folding ensures that the impact resistant is high and No. concrete seepage occurs. Material Specification: As per BS2989 (Indian Standards IS 277:2003).Tensile Strength: 500N/m2.The material thickness should be 2 MM Top Cover and base cover is 1.6mm with a standard length of 2.5Rmtrs.The trunking should be compartmentalized for provision of data, power and voice cables. The trunking should have a depth of 38mm with three compartments all required accessories Complete in all respect. equivalent to MK Cat.No..UMDXT225/3/6
Supply and installation of GI Trunking made up of Pre Galvanized sheet metal with zinc coated steel sheet double folded and arc welded. The double folding ensures that the impact resistant is high and No. concrete seepage occurs. Material Specification: As per BS2989 (Indian Standards IS 277:2003).Tensile Strength: 500N/m2.The material thickness should be 1.6MM Top Cover and base cover is 1.6mm with a standard length of 2.5Rmtrs.The trunking should be compartmentalized for provision of data, power and voice cables. The trunking should have a depth of 38mm with three compartments all required accessories Complete in all respect. equivalent to MK Cat.No..UMDX75/1/6
Supply and installation of of Cross Overs boxes manufactured from high-pressure die cast material. The Trap Cover & Trap frame of the box should be made of 2.5mm thick pre-galvanized steel plate made of Electrostatic Polyester epoxy coating. The recess should be 8mm on the trap lid to accommodate the specified flooring The cross over boxes should have flyover units made of ABS plastic or metal to route and distribute power, data and voice cables. The system must have smooth curved die cast pillars for ease of pulling cables. The base of the box is made of pre-galvanized sheet steel with a thickness of 1mm. The system must have the provision to accommodate 25/38mm deep GI trunking, with width kNo.ckouts to accommodate trunkings from a minimum of 50mm upto a maximum of 300mm. Height adjustment: The system must have the stainless steel leveling screws. Load bearing Capacity: Upto 3.6 tons on the trap lid Standards: The system must comply with the relevant specification & IEC 61084 and all required accessories Complete in all respect equivalent to MK Cat.No...EJB250/3
Supply and installation of of boxes manufactured from high-pressure die cast material. The Trap Cover & Trap frame of the box should be made of 2.5mm thick pre-galvanized steel plate made of Electrostatic Polyester epoxy coating. The recess should be 8mm on the trap lid to accommodate the specified flooring . The system must have smooth curved die cast pillars for ease of pulling cables. The base of the box is made of pre-galvanized sheet steel with a thickness of 1mm. The system must have the provision to accommodate 25/38mm deep GI trunking, with width kNo.ckouts to accommodate trunkings from a minimum of 50mm upto a maximum of 300mm. Height adjustment: The system must have the stainless steel leveling screws. Load bearing Capacity: Upto 3.6 tons on the trap lid Standards: The system must comply with the relevant specification & IEC 61084 and all required accessories Complete in all respect equivalent to MK Cat.No...JB150
Supply and installation of Cable Management System- Prestige 3D to distribute power, data and telecom cables. The system should comply with all relevant sections of the latest edition of IEE wiring regulations and shall be CAT 6 compliant. The system shall comprise of base & lid with snap-fit lid and allied accessories such as data sweep, cable retainers, flat angle, flat tee etc. The three compartment system shall have cross sectional dimensions of 170mm height and 57mm in depth and with a wall thickness of 1.7mm on lid and 2mm on cover. The main carrier should be pre-drilled at 300mm centres with a divider kNo.ckout after every 100mm intervals. Material should be No.n flame prorogating and a Class 1 spread of flame achieved when tested in accordance with the requirements of BS EN 50085-1:1999 and BS EN 61386-1:2004. The System shall have provision to accept mounting boxes that snap fit in to the profile and that accept MK wiring accessories and internal angle, external angle ,joint cover with end cap.equivalent to MK Cat.No...VP180 WHI
ELW 13.00Light Fixtures and Fans Supplying and erecting, testing and commissioning of 18W LED recessed Mounted Down Lighter -Make Wipro (18W MOLIS LD06-221-XXX-57-XX) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 12W LED recessed Mounted Down Lighter -Make Wipro (12W MOLIS LD06-151-XXX-57-XX) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 33W LED Recessed Mounted Circular Down Lighter -Make Wipro (MOLIS LD06-301-XXX-57-XX) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 36W LED Recessed Mounted Square indoor Panel -Make Crompton (LCTLRN-36-F0-CDL) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 50W LED Recessed Mounted Square indoor Panel -Make Crompton (LCTLRN-50-F0-CDL) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 1x10W 600mm LED Surface Mounted indoor Linear smart Bright Battern Lights Fittings -Make Phillips ( BN021) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 1x20W 1200mm LED Surface Mounted indoor Linear smart Bright Battern Lights Fittings -Make Phillips ( BN021C) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 18WLED Surface Mounted Down Lighter -Make Crompton (LCDSPLN-R-18-CDL) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 12W LED Surface Mounted Down Lighter -Make Crompton (LCDSPLN-R-12-CDL) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 26W Circular LED Surface Mounted indoor Lights Fittings with High Efficency Translucence Diffuser -Make Wipro ( MOLIS LD06-301-XXX-57WSM) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 25W Cylindrical LED Surface Mounted indoor Lights Fittings with High Efficency Translucence Diffuser -Make K-LITE CYLIN ID-7346 or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 38W 650mm dia LED Hanging Light Point Type Vela Round 1250 direct/indirect -Make XAL or equilavent (iO-71-260 38 W) ( 4000K)
Supplying and erecting, testing and commissioning of 20W LED Surface Mounted Industrial Corroson proof Fixture Ip 65 -Make Crompton (IPFC111LT8-16 1X 20W) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 40W LED Surface Mounted Industrail Corroson proof Fixture Ip 65 -Make Crompton (IPFC112LT8-16 2X 20W) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning LED Up & Wall Bracket Light Point -Phillips or equilavent (Type -QPG 303) (Lamp -12 to 14w led e27)
Supplying and erecting, testing and commissioning of 10W LED Wall Mounted Bulk head Light -Crompton (Type-STUD-LBHP-10-CDL) or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 21W 4' Feet LED Surface / Recessed / Suspended Mounted indoor Channel Linear Lights Fittings with diffuser-Make Philips make Channel RC780B LED 26S-6500PSU W6L120ODSI or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 46W 8' Feet LED Surface / Recessed / Suspended Mounted indoor Channel Linear Lights Fittings with diffuser-Make Philips make Channel RC780B LED 52S-6500PSU W6L240ODSI or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 40W 4' Feet LED Surface / Recessed / Suspended Mounted indoor Channel Linear Lights Fittings with diffuser-Make SP780P LED 26S-6500PSU W6L120ODSI or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 60W 8' Feet LED Surface / Recessed / Suspended Mounted indoor Channel Linear Lights Fittings with diffuser-Make SP760P LED 52S-6500PSU W6L240ODSI or equivalent as per apporved make list.
Supplying and erecting, testing and commissioning of 80W 8' Feet LED Surface / Recessed / Suspended Mounted indoor Channel Linear Lights Fittings with diffuser-Make SP780P LED 52S-6500PSU W6L240ODSI or equivalent as per apporved make list.
SITC of Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 230 V. 50 Cys. 900 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2, 3 core flexible wire with earthing
SITC of Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 230 V. 50 Cys. 1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2, 3 core flexible wire with earthing
SITC of 19/20mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/O. 2 flat 3 core flexible wire with ear thing.
SITC of approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame.ABS body with inbuilt lowers & square frame.
Supplying and erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM. (E)450 mm dai 1400 RPM (CAT-2)
SITC of suitable M.S. louver shutter of the Exhaust fan.
ELW 14.00 Earthing Supplying, installing, testing & commissioning of Maintenance Free Chemical Earthing System consisting of (A) Copper Bonded Earth Rod of 3 Mtr x 5/8" size using earth enhancing compound of 25 Kg & termination clamp. Complete in all respect with all reuqired accessories.
Earth wire/strips : Supply and laying cu. earthing required size strips for interconnecting the earthing stations, panels, DB's etc. in built up trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with : a) Fixing accessories. b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. 25 x 3 mm/ 32X6mm / 50x6mm CU. strip/ 38x6 Cu earth link
SITC of No.8 gauge bare cu. earth wire Complete in all respect with all reuqired accessories.
ELW 15.00 External Lighiting Poles Supply & installation of 3.6 Mtr long, 139 mm outer uniform dia. GI street light pole with medium class ( minimum 4.5 mm thick) GI pipe with zinc coating and two coats of paint / pu coats of approved shade complete as approved by architects with base plate as per requirement complete in all respect as per drawing. Junction box shall be in concealed manner (inside the pole)with one no 2A SP mcb and 5 way 16A Connector strip suitable to terminate armoured cables. Adequate size cutout with opeanable hinged door should be provided on pole with necessary gasket to ensure water tight arrangement for pulling cables and installation of mcb, connectors etc, complete in all respect as per requirement and instruction of engineer in charge and tender drawing.Scope also includes necessary foundation, Spiral earthing, cable entry pipes, minumum 2.5sqmmx 3 core round flexible wire from junction box to light fixture etc,.
Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE for road having Height - 6 metre (Single Arm) having thickness of 4.5 mm, 139.7 mm outer uniform dia., with base plate of 450 x 450 x 16 mm with stiffener plate with 1 Nos Seprate integral type junction box ( For Street light) , with complete concrete foundation with necessary reinforcement, j bolt, necessary hardware as per detail, with necessary Reducer / Coupler / for fixing of light fixtures & Hinged access door with welded chain between pole and hinged door with Allen key require to access the integral junction box, Fabrication work complete in all respect as per given detail with one coat of zinc oxide complete in all respect as per Drawing. Rate shall be including two coats of PU paint of shade as per drawing or as directed by Architect ( effective length should be 6000mm above GF) (Sample to be approved) 1) with necessary 1 Nos 6 way connector, 1 Nos. 2A SP MCB with din rail channel, 8mm thk. Hylem sheet, 12x2 mm thk. GI Patti Clamp, with necessary required hardware, necessary welding & Fabrication work (if required) complete in all respect. 2) 40 mm diameter GI pipe for each cable entry . 3) Wiring up to the light fixture from the junction box using 3nos. x 1.5 sq.mm.flexible copper wires of specified make for each fixture. 4) Concrete foundationwith base plate. 5) Excavation for erection of poles as per drawing complete in all respect. 6) Pole Numbering to be carried out by contractor as instructed by Site in charge as per Client's requirement.
Supply & Installation of GI Pole made out of B CLASS ERW G.I. PIPE for road having Height - 6 metre (Double Arm) having thickness of 4.5 mm, 139.7 mm outer uniform dia., with base plate of 450 x 450 x 16 mm with stiffener plate with 1 Nos Seprate integral type junction box ( For Street light) , with complete concrete foundation with necessary reinforcement, j bolt, necessary hardware as per detail, with necessary Reducer / Coupler / for fixing of light fixtures & Hinged access door with welded chain between pole and hinged door with Allen key require to access the integral junction box, Fabrication work complete in all respect as per given detail with one coat of zinc oxide complete in all respect as per Drawing. Rate shall be including two coats of PU paint of shade as per drawing or as directed by Architect ( effective length should be 6000mm above GF) (Sample to be approved) 1) with necessary 1 Nos 6 way connector, 1 Nos. 2A SP MCB with din rail channel, 8mm thk. Hylem sheet, 12x2 mm thk. GI Patti Clamp, with necessary required hardware, necessary welding & Fabrication work (if required) complete in all respect. 2) 40 mm diameter GI pipe for each cable entry . 3) Wiring up to the light fixture from the junction box using 3nos. x 1.5 sq.mm.flexible copper wires of specified make for each fixture. 4) Concrete foundationwith base plate. 5) Excavation for erection of poles as per drawing complete in all respect. 6) Pole Numbering to be carried out by contractor as instructed by Site in charge as per Client's requirement.
STREET LIGHT FIXTURE Supplying, erecting, connecting, testing and commissioning of following type posttop Light Fixture with all necessary Hadware, Internal Wiring with Lamp,Ballast etc. all required accessories Complete in all respect. Posttop Light fixture-Make - Keselec Nena, 35W LED lamp, Integral Ballast, Minimum IP65, IK 08 or equivalent as per apporved make list.
STREET LIGHT FIXTURE Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 85 lumens/watt . LED driver efficiency > 85 %. CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 certificates) (A) Street Light (IP-65), Surge -4KV (d) above 36 to 48 watts
ELW 16.00 Miscellaneous MISCELLANEOUS PVC PIPES Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 25 mm dia with GI pulling wire.
Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 32 mm dia with GI pulling wire.
Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 40 mm dia.
Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 50 mm dia.
DWC PIPES Providing & laying. DWC pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with necessary material in an approved manner and making the ground as per original. (A) 50 mm dia
Providing & laying. DWC pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with necessary material in an approved manner and making the ground as per original. (B) 90 mm dia
Providing & laying. DWC pipe for cable to be laid 90 cms. below ground across the road crossing or on floor with necessary material in an approved manner and making the ground as per original. (A) 120 mm dia
Fire Stopper SITC of Fire stop mortar system , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814 standards, for horizontal openings in floors or slabs after passing service lines like cables/cable bundles, cable trays etc. The system shall be UL listed & classified and product shall bear the UL and FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer. A firestop submittal shall be produced by manufacturer , in accordance with approved passive fire protection method statement, for technical approval. Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer guidelines and UL system test certificates or approved EJ document. .
SITC of rodent and termite proof Fire Barriers on both sides of wall ( Composite Sheet) system for 2 hours fire rating when tested in accordance with ASTM E 814/UL 1479 standards. The small gaps left around the penetrants should be closed with Intumescent sealant , or with Fire rated Moldable Putty , which should be soft & moldable to any shape, to give complete L Rating. This system is to seal all fire rated vertical in wall made of concrete, masonry, metal, gypsum partition, after passing service lines like cables/cable bundles, cable trays etc. The system shall be UL listed & classified and product shall bear the UL & FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer. Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer's guidelines and UL system test certificates or approved EJ document.
SITC of Provide expanding firestop foam on both sides of wall, with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814, for horizontal/ vertical openings in floors / wall or slabs made of concrete/ masonry or Gypsum after passing service lines like cable trays or cables/cable bundlesThe system shall be UL listed & classified and product shall bear the UL and FM approval logo on the packing. The system shall be UL listed & classified and product shall bear the UL & FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer.Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer's guidelines and UL system test certificates or approved EJ document.
SITC of Firestop Factory-assembled cable device Speed Sleeve - (4" Size) , containing an intumescent material and a flexible cloth which limits the warm and cold smoke propagation to less than 1 CFM per device for passing cables through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814. The system shall be UL listed & classified and product shall bear the UL and FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer. Firestop installation shall be done by manufacurer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer's guidelines and UL system test certificates or approved EJ document.
SITC of intumescent based coating on cables/bunch cables & cable tray for at least 1 mtr in every 14 mtrs for horizontal runs and to entire length of vertical runs . The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength. Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer's guidelines .
SITC of Pre-formed block CFS BL made from intumescent polyurethane material for temporary or permanent firestop sealing around cables, cable bundles and conduits. The system shall be UL listed & classified and product shall bear the UL & FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer. Firestop installation shall be done by Hilti Accredited Firestop Speciality Contractor (HAFSC) and in accordance with Hilti guidelines and UL system test certificates or approved EJ document.
ELW 17.00 Lighitning Protection Air termination System Supply, Installation, Testing & Commissioning of 8mm Aluminum Solid Round Conductor for building terrace as a horizontal air terminal as per required LPL and should be tested for electrical resistivity, Tensile strength, Yield strength, % elongation, salt spray & humidity test to meet the requirements of IS/IEC 62305 and IEC 62561-1&2 with all accessories like of Stainless steel Parapet Conductor Holder, Flat roof Conductor Holder, Stainless Steel cross connector, Expansion Piece with connector at every 20mtr of horizontal airterminal to compensate the expansion, Straight connector etc.
Down Conductor System Supply, Installation, Testing & Commissioning of 10 mm copper bonded Round steel solid Conductor for Down conductor meet the requirements of IS/ IEC 62305 and IEC 62561-2 with Bonding clamp/Rebar Hook for interconnecting 10mm-18mm round conductor and stainless steel straight connector at every 3.5M. CAPE Type No. SRC 10 – CU (Article No. 400 010)
Earthing System Supply, Installation, Testing & Commissioning of 10 mm copper bonded Round steel solid Conductor for ring earthing meet the requirements with installation of welding. of IS/ IEC 62305 and IEC 62561-2 CAPE Type No. SRC 10 – CU (Article No. 400 010)
ELW 18.00 UPS Supply , Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 50KVA UPS 3 ph in 3 ph out for balance load
Supply , Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 6KVA UPS 1 ph in 1 ph out for balance load
Supply , Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 5KVA UPS 1 ph in 1 ph out for balance load
Supply , Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 2KVA UPS 1 ph in 1 ph out for balance load
ELW 19.00 SOLAR SYSTEM SOLAR PLANT Design, Engineering, Supply, Installation, Testing & Commissioning of 100 KWp Grid connected Solar PV Power Plant consisting of Solar PV modules, Power Conditioning Unit (Inverter with all accessories/ features), Junction Boxes, PVC Pipes, Cables/Wires including connectors/plugs/fuses, ACDB, Suitable Lightening Arrestor/Earthlink etc. and accessories along with Tool kit and spares for 1 year. The scope of work includes suitable mounting Fabrication along with all cables, hardware, nuts, bolts etc.
SOLAR PLANT Design, Engineering, Supply, Installation, Testing & Commissioning of 70 KWp Grid connected Solar PV Power Plant consisting of Solar PV modules, Power Conditioning Unit (Inverter with all accessories/ features), Junction Boxes, PVC Pipes, Cables/Wires including connectors/plugs/fuses, ACDB, Suitable Lightening Arrestor/Earthlink etc. and accessories along with Tool kit and spares for 1 year. The scope of work includes suitable mounting Fabrication along with all cables, hardware, nuts, bolts etc.
SOLAR PLANT Design, Engineering, Supply, Installation, Testing & Commissioning of 30 KWp Grid connected Solar PV Power Plant consisting of Solar PV modules, Power Conditioning Unit (Inverter with all accessories/ features), Junction Boxes, PVC Pipes, Cables/Wires including connectors/plugs/fuses, ACDB, Suitable Lightening Arrestor/Earthlink etc. and accessories along with Tool kit and spares for 1 year. The scope of work includes suitable mounting Fabrication along with all cables, hardware, nuts, bolts etc.
SOLAR PLANT Design, Engineering, Supply, Installation, Testing & Commissioning of 20 KWp Grid connected Solar PV Power Plant consisting of Solar PV modules, Power Conditioning Unit (Inverter with all accessories/ features), Junction Boxes, PVC Pipes, Cables/Wires including connectors/plugs/fuses, ACDB, Suitable Lightening Arrestor/Earthlink etc. and accessories along with Tool kit and spares for 1 year. The scope of work includes suitable mounting Fabrication along with all cables, hardware, nuts, bolts etc.
SOLAR PLANT Design, Engineering, Supply, Installation, Testing & Commissioning of 5 KWp Grid connected Solar PV Power Plant consisting of Solar PV modules, Power Conditioning Unit (Inverter with all accessories/ features), Junction Boxes, PVC Pipes, Cables/Wires including connectors/plugs/fuses, ACDB, Suitable Lightening Arrestor/Earthlink etc. and accessories along with Tool kit and spares for 1 year. The scope of work includes suitable mounting Fabrication along with all cables, hardware, nuts, bolts etc.
4.00 ELV SYSTEMS Sec.1.0 Telephone and Data Networking Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed. 25 mm as per technical specification etc. as required.
Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed. 40 mm as per technical specification etc. as required.
Tag Blocks - Multipair Telephone Cable Termination Supply & fixing of 50 pair MDF unit with required modules in a fabricated CRCA powder coated junction box of size 450x250x100 with two no. of pad-lock, provision for earthing. as per technical specification etc. as required.
Supply & fixing of 100 pair MDF unit with required modules in a fabricated CRCA powder coated junction box of size 450x250x100 with two no. of pad-lock, provision for earthing. as per technical specification etc. as required.
Supply & fixing of 500 pair MDF unit with required modules in a fabricated CRCA powder coated junction box of size 450x250x100 with two no. of pad-lock, provision for earthing. as per technical specification etc. as required.
Cabling - Multipair Cables Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (b) Armoured. (Jelly Filled) (3) Fifty Pairs. as per technical specification etc. as required.
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. A Conductor Size 0.5 mm. (b) Armoured. (Jelly Filled) (4) One Hundred Pairs. as per technical specification etc. as required.
Telephone / Data Networking Cabling Supplying & erecting approved make LAN cable of following size in existing pipe as per direction. [C] CAT - 6 as per technical specification etc. as required.
Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (8) Modem Jack for Computer Open RJ-45. Cat. III. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of UTP CAT6 24 ports capacity gigaspeed patch panel, all ports loaded with individual RJ-45 IOs. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of UTP CAT6 RJ45 ethernet patch cord - 7 feet as per technical specification etc. as required.
Supplying, installation, testing and commissioning of UTP CAT6 RJ45 ethernet patch cord - 3 feet as per technical specification etc. as required.
Data Networking - Fiber Optic Cable and Components Supplying, installation, testing and commissioning of outdoor 6 core armoured single mode fiber optic cable for outdoor connectivity where ever required in prelaid conduits / RCC hume pipes/HDPE/DWC, whichever maybe available etc. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of outdoor 12 core armoured single mode fiber optic cable for outdoor connectivity where ever required in prelaid conduits / RCC hume pipes/HDPE/DWC, whichever maybe available etc. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 19" rack mounting type fiber shelf for assembly/termination of minimum 24 cores of singlemode ofc cable for LC style components, for optical splicing and provision for storage of pigtails and splices, equipped with adaptors, adaptor plates and any other such all necessary hardware for proper dressing and management of fiber optic cable etc. as required. Any blank adaptor positions must be suitably masked for restricting dust entry etc. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 19" rack mounting type fiber shelf for assembly/termination of minimum 12 cores of singlemode ofc cable for LC style components, for optical splicing and provision for storage of pigtails and splices, equipped with adaptors, adaptor plates and any other such all necessary hardware for proper dressing and management of fiber optic cable etc. as required. Any blank adaptor positions must be suitably masked for restricting dust entry etc. as per technical specification etc. as required.
Supplying, Splicing , testing and commissioning of LC type single mode pre-terminated pigtail 1mtr as per tender specification etc. as per technical specification etc. as required.
Supplying, Installation, testing and commissioning of LC-LC single mode duplex fiber optic patch cord 1mtr. as per technical specification etc. as required.
Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. for OFC Marker, as per technical specification etc. as required.
Networking Enclosures & Accessories Supply, Installation, Testing & Commissioning of 15U (600W X 550D)MM Wall mount closed rack with front glass door, fan tray on top, perforated rear doors, keyboard tray with shelf. Casters & 2 nos vertical power strip with std etc. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 24U (600W X 600D)MM Floor mount closed rack with front glass door, fan tray on top, perforated rear doors, keyboard tray with shelf as required . Casters & 2 nos vertical power strip with std,. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 42U Floor standing 19" networking enclosure as per specification and complete with all accessories. (upto size - 800mmW x 1000mmD) as required. (along with horizontal cable manager & vertical cable manager, PDU with minimum 12 Nos. 16 Amp socket, as per technical specification etc. as required.
Active Components- Data & Voice Networking TYPE-1 Supplying, installtion, testing and commissioning of Layer 3 features switch: 24 # port 10G SFP+ With redudant power supply & standard mouting hardware & accessories. Core Switch for Server room, as per technical specification etc. as required.
TYPE-2 Supplying, installation, testing and commissioning of Layer 2 Fully manageable networking switch, 24 # 10/100/1000Tx ports, all 24 ports shall be capable of providing PoE+ as per 802.3at, minimum 2 SFP+ ports. as per technical specification etc. as required.
TYPE-3 Supplying, installation, testing and commissioning of Layer 2 Fully manageable networking switch, 24 # 10/100/1000Tx ports, minimum 2 SFP+ ports as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 10G SFP+ Single mode transceiver, 1310nm, 2Km, LC connector, inclusive of any hardware such as modules for populating SM-LC transceivers as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Wireless indoor Access Point supporting Dual band with 802.11a/n/ac (5 GHz) and 802.11g/n (2.4GHz) concurrent operation with MIMO support 3x3, 3 spatial streams, One 10/100/1000 BASE-TX auto-sensing (RJ45) PoE port, as per technical specification etc. as required.
Supplying, installtion, testing and commissioning of Room Wireless access point 802.11ac (2x2) Wave 2, with internal omni-directional antennas, 1 x 10/100/1000 Base-T with PoE In ( 802.3af/at ) port 4 x 10/100/1000 Base-T ports, with required licenses to compatible with Wireless controller as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Hardware based Wireless Access Controller, License with Minimum 200 Access point and support up to unlimited access point, as per tender specification etc. as required.
Supply, Installation, Testing and Commissioning of Small EPABX System with In Built 4 Port Voice Mail. No. Extension - 128 , No. of Junction -24 , No. of expandable ports -512 , Operators Console -01 Compatible - ISDN & Networking as per tender specification etc. as required.
Supply, Installation, Testing and Commissioning of IP Phone with display as per tender specification etc. as required.
Supplying & erecting push button type telephone instrument having speaker phone Caller ID & hands free dialling system & 30 memories with display system (a) Single line
Supply, Installation,Testing and Commissioning of Digital Telephone with DSS console and related software/ licences as per tender specification etc. as required.
Sec.2.0 Video Survelance/CCTV System Supply, Installation, Testing & Commissioning of Vandal reistant True Day Night Veri-Focal Dome Camera 2MP, Full HD, 1/2.8 type CMOS image sensor, 2.8 -12mm motorized focus lens, Aperture Ratio F1.8, Wide Dynamic Range - 120dB, H.265 / H.264 & MJPEG dual-stream encoding, 25/30fps@1080P (1920 ×1080), IR LEDs length minimum 20 m, Motion Detection , Tampering ,Defocus detection , Hallway view ,Micro SD Card - 128GB capacity, IP66 rated, IK 10 and as per technical Specification ,The Camera must be UL Listed. as per technical specification etc. as required.
Supply, Installation, Testing & Commissioning of True Day Night Bullet Camera 2MP, Full HD, 1/2.8 type CMOS image sensor, Autoiris Varifocal lens 2.8 - 12mm motorized focus lens , Aperture Ratio F1.4, Wide Dynamic Range - 120dB, H.265 / H.264 & MJPEG dual-stream encoding, 25/30fps@1080P (1920 ×1080), IR LEDs length minimum 30 m, Motion Detection , Tampering ,Defocus detection , Hallway View, Micro SD Card - 128GB capacity, IP66 rated, IK 10 as per technical specification The Camera must be UL Listed, as per technical specification etc. as required.
Supply, Installation, Testing & Commissioning of Vandal Resistant PTZ Network Cameras ,IR with 350 Mtrs Viewing Distance 30 X Optical Zoom,camera with 1/1.9" sensor, 2MP, Full HD(1080p) @60fps WDR off or @15fps WDR on, H.265/H.264/MJPEG, 120dB WDR, Auto Tracking, true D/N, ,Edge Analytics - Auto Tracking, Virtual Perimeter, Entry/Exit Detection, Tampering,SD/SDHC/SDXC memory slot, 24VAC, IP66, IK10 .including all mounting accessories.The Camera must be UL Listed, as per technical specification etc. as required.
Supply Installation Testing & Commissioning of Network Storage Management software (NSM) supporting ONVIF Profile S , PSIA, real time streaming protocol (RTSP) standards, 4K resolution, H.265 video compression codec, 3D PTZ control, and intelligence events. System proposed shall have 128 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps . NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity complete with hardware as per specification. as per technical specification etc. as required.
Supply, Installation, Testing & Commissioning of Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's licenses 128 cameras, 3 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, HTTPS, SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID, iOS phones, seamless integration with intgegrated security platform which provides HSDK, API for further integration with 3rd party systems. as per specification. as per technical specification etc. as required.
Supplying, installtion, testing and commissioning of Server(s) required for NSM & NVMMS - Industry standard Intel based platform, rack mounted, redundancy architecture for critical hardware components, licensed Microsoft Server operating system and requisite user licenses, licensed application suites, 2 x Quad Core Intel® Xeon latest processors or better, 8 GB of RAM, 2 x 1.2 TB of SAS HDDs, minimum 2 additional hard disk drive bays for expansion, 1,280 x 1,024 Display/ video resolution, 2 X 10/100/1000 ethernet network interface card, Video memory 2GB above, RAID support built-in, DirectX 8.1 above and pre-installed DVD-R/W Drive and Appropriate Licensed Operating Systems as per NSM & NVMMS Requirement. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of Client PC - Industry standard Intel based platform computer system. Intel Core i7 latest generation, 4 GB of RAM DDR3 ,1 TB SATA II hard drive for OS and VMS applications, NVidia card 1 GB graphics card , 1600 x 1200 or higher screen resolution, 1 X 1000Mbps ethernet network interface card ,16x DVD+/- RW Drive alongwith appropriate licenced Operating System, licenced applications suites from OEM and application licences as per the technical specifications etc. as required.
Supplying, installation, testing and commissioning of Network storage required with a capacity to store the content for 165 cameras for 24Hrs x 30 days at 25fps and 1080p (Minimum 110TB from day 1). It should be scalable (should have sufficient expansion bays for HDDs) for at least additional 50 cameras. Vendor shall submit bandwidth and storage calculator for the proposed camera models as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Network Keyboard, 7" TFT touch screen, up to 256 units of DVR/Network Cameras/Speed Dome management, 1-ch HD 1080p video steam decoding, USB 2.0 interface for video backup
Supply installation testing and commissioning of 55" Full HD LED Video wall display, 3.5 mm bezel to bezel, 500 Cd/m2 brightness, DVI-D Loop out-Daisy chain, DVI- D IN X 1, VGA X 1, HDMI X 2, DVI-I Out x 1, LAN, with required mounting bracket as per site requirement. as per technical specification etc. as required.
Supply installation testing and commissioning of AV over IP JPEG 2K Encoder with 1 X HDMI IN, 1 X LAN, 1 X RS232 Out, featured with videowall function with mounting accessories. as per technical specification etc. as required.
Supply installation testing and commissioning of AV over IP JPEG 2K Decoder with 1 X HDMI Out, 1 X LAN, 1 X RS232 Out , featured with videowall function with mounting accessories. as per technical specification etc. as required.
Supply installation testing and commissioning of Automation Controller with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control video wall. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.
Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of fault isolator complete with base as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of addressable fire control / Monitor module complete as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of addressable manual call point complete as required. as per technical specification etc. as required.
Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. as per technical specification etc. as required.
Fire Detection and Alarm System (Conventional) Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone
Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.
Digital Evac / Public Address System. Supply, Installation, Testing and Commissioning of 8 zone IP based digital Voice Alarm controller expandable upto 128 zones. The voice alarm controller should be able to connect directly over Ethernet. It should have functions like the audio playing, zone control, fault monitoring, log recording, volume control and amplifier switchover. The Voice alarm controller should also have the following functions, 255 Priorities, Time schedule broadcasts, Its own PTT microphone, Capable of amplifier redundancy, 8 trigger inputs/outputs , as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of 1X500W Class-D Amplifier with 2 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of 6W Ceiling Speaker with max SPL1M/1W 96dB . Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of 6W Wall mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of integrated Audio source with the following features : Two single CD\USB\SD and DAB\FM line outputs can play music applications in two areas, The volumes of the two line outputs can be adjusted separately, CD\USB\SD has three play modes: single play, all play and repeated play, DAB\FM can preset 10 channels of programs, RS485 remote control interface as per technical specification etc. as required.
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Single pair, 2-core, 1.5 sqmm, For FAS & PA System
Sec.4.0 Access Control System “Providing & erecting approved make Fingerprint and card based premium Door controller with LCD and Keypad having following features.”(A) Optical Fingerprint and card based Reader (Card personality Module not included) “(B) Dot – Matrix LCD and Touch sense Keypad “(C) Built-in interfaces like door lock, door sense exit Reader, Exit switch, Ethernet RS485, Aux Input & aux output port “(D) 5000 Events, access Control, Time Attendance, Tamper Detection “(E) 4 LEDS and Buzzer”
“Providing & erecting approved make Card Reader having following features. “[A] Wiegand/ RS232 Interface “(B) Power supply from COSEC Door controller or through Separate Adaptor “(C) Compatible with any COSEC Door controllers “(D) 4 LEDs (Status, Alarm, Allowed and Denied) and Buzzer “(E) Tamper Detection”
“Providing & erecting approved make Card Personality Module (CPM) having following features “(A) EM proximity Card Reader Module [Low Frequency] “(B) Compatible with any COSEC Door Controllers and COSEC Reader CA “(C) Supports EM Proximity Card”
“Providing & erecting approved make Panel Controller for Multiple Door Controller having following feature “(A) Controls up to 16 Door Contioiiers “(B) Ethernet RS485, USB, Aux Input and Aux output port “(C) 10000 Users Capacity and 100000 Events Storage “(D) 32-bit processor, 32 MB RAM and 32 MB Flash “(E) Compact and Elegant Design”
Providing & erecting approved make Application Software Platform for 500 User having following features “(A) With 100 Users “ (B) Expandable up to 500 Users with COSEC USER 100 “(C) Supports up to 16 Door Controller “(D) Basic Access Control Basic Time Attendance and Enrollment Management (E) Compatible with all COSEC Hardware “(F) Add Other COSEC software modules on requirement.
Providing & erecting approved make Time Attendance Module (TAM) Having following features “(A) Comprehensive Time Attendance and Leave Management Software Module “(B) For 500 Users [AS per COSEC GE PLATFORM USERS] “(C) Attendance and leave Policy Creation “(D) Integration with payroll and HRM “(E) Shift Schedule, Holiday Schedule and Past Adjustment “(F) Manually Attendance Correction “(G) Leave/Tour Application and approval “(H) Report and Charts Generation
“Providing & erecting approved make Access control Module (ACM) having following features (A) Comprehensive Access Control Management (B) For 500 Users [AS PER COSEC GE PLATFORM users] (C) Time, User and Zone Based Access Control (D) Access Zones, Access Modes and Access Levels (E) Advanced Access Control Feature like 2-person rule, First in user rule, Antipass Back, Guard Tour, Duress Detection and more (F) Various Reports Generation
Supply, Installation, Testing & Commissioning of Drop Bolt Or EM Door Lock as per Door type & site Location requirement.
Sec.5.0 Cable TV Distribution System Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (4) TV Co-axial Socket outlet. Cat. III.
Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly – Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. (b) RG – 6.
Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly – Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. (e) RG – 11.
Audio Visual System Supplying, installation, testing and commissioning of 86" All in One Interactive display features with 20 Points in Windows/ 10 Points in Android touch points, Passive Pen/ Finger/ Palm Writing Tools, 15 W × 2 builtin speaker, Minimum 350 nit Brightness, wireless presentation solution, white board software, broadcasting to 200 devices, remote display management, On-board Computer OPS with I7-6500U processor, 4G*2 DDR4 memory, 256G SSD storage, WIFI/BT 802.11ac/BT4.0, Intel 1000M network interface, Display Minimum Interface : HDMI 1.4 × 1, USB(Touch) × 1, USB(Dynamic) × 2, MIC × 1, HDMI 2.0(4K@60Hz) × 2, DP 1.2(4K@60Hz) × 1, VGA(1920x1080@60Hz) × 1, PC Audio × 1, USB(Touch) × 4, HDMI Out (Support 4K@60Hz) × 1, RS232 × 1, RJ45 × 2 with wall mount kit as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 75" All in One Interactive display features with 20 Points in Windows/ 10 Points in Android touch points, Passive Pen/ Finger/ Palm Writing Tools, 15 W × 2 builtin speaker, Minimum nit Brightness, wireless presentation solution, white board software, broadcasting to 200 devices, remote display management, On-board Computer OPS with I7-6500U processor, 4G*2 DDR4 memory, 256G SSD storage, WIFI/BT 802.11ac/BT4.0, Intel 1000M network interface, Display Minimum Interface : HDMI 1.4 × 1, USB(Touch) × 1, USB(Dynamic) × 2, MIC × 1, HDMI 2.0(4K@60Hz) × 2, DP 1.2(4K@60Hz) × 1, VGA(1920x1080@60Hz) × 1, PC Audio × 1, USB(Touch) × 4, HDMI Out (Support 4K@60Hz) × 1, RS232 × 1, RJ45 × 2 with wall mount kit as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 5000 lumens WUXGA 3LCD Laser Projector, Contrast Ratio - 2,500,000 : 1, With Standard Lens, Input terminal : D-Sub 15Pin X 2nos. HDbaseT RJ45 x 1, HDMI X 2nos, Stereo Mini Jack x 2nos. Output Terminal : D-Sub 15Pin: 1 Shared with Computer 2, Stereo Mini Jack: 1 with ceiling mount kit (2feet + 2feet) or as per site requirement.
Supplying, installation, testing and commissioning of 137" (72" X 116") inch Diagonal or equivalent size 16:10 aspect ration motorized projector screen.
Supplying, installation, testing and commissioning of 165" (81" X 144") inch Diagonal or equivalent size 16:9 aspect ration motorized projector screen.
Supply installation testing and commissioning of Wall–Plate Auto Switcher, Inputs: HDMI x1nos, VGA with Audio x 1 nos, Outputs: HDbaseT RJ45 x 1nos, Unbalanced Stereo Audio x 1nos, Ethernet x 1nos. With wall or table mount enclosure as per technical specification etc. as required.
Supply installation testing and commissioning of 4K HDBT Receiver / Scaler Tool with Input: HDBaseT RJ45 x 1nos, Outputs: HDMI x1nos and Balanced Analog Stereo Audio x 1nos, as per technical specification etc. as required.
Supply, installation, testing and commissioning of All–in–One Presentation Switcher cum scaler with Room Controller & Power Amplifier, Minimum 6 HDMI & 2 HDBT inputs, Minimum 2 HDMI & 2 HDBaseT outputs, include master controller with 1 RS–485 and 4 RS–232 Bidirectional Control, 4 IR Emitter, 4 GPI/O Control Ports, 8 Relay Ports, should have inbuilt power amplifier wih 2x50W into 4ohms as per technical specification etc. as required.
Supplying, installation, testing and commissioning of 4 in 1 Media processor - supports recording, switching, mixing and live streaming at 1080p, Supports 1080p 60/30fps video recording, Supports 4 HDMI Inputs and IP video sources, Should have minimum 1TB inbuilt storage. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of Full HD 1080p, Minimum 20X Optical Zoom, 20 Presets, 30 Frames per Second, Ethernet Out, HDMI Out, 3G-SDI Out, Audio In, RS232/422 Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle capturing presenter and students. as per technical specification etc. as required.
Supplying, installation, testing and commissioning of Joystick for PAN/Tilt/Zoom Cameras and Focusing, RS232C/RS455 Communication Interfaces, High Brightness OLED Display, Auto Backlit Keys.as per technical specification etc. as required.
Supply, installation, testing and commissioning of Wireless Presentation , should present minimum 2 users laptops or handheld devices on a single display at a time with inbuilt wi-fi, should have annotation & white board feature, able to share uninterrupted HD video of 1080p @ 60 FPS, as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Ceiling speaker 6.5" 2-way minimum 60 watts continuous power, 100 V - 12 W , 24 W , 6 W tapping connection and a low-Z output for loudspeakers with impedances from 4 ohms upwards, Frequency response - 70 - 20000 Hz, Sensitivity (1 W / 1 m) -88 dB, as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of FOH Speaker Wall mount 12" passive Installation Speaker black, 250 W permanent load capacity, 121 dB maximum,Impedance - 8 ohms, Speaker input connections - Speakon , horn with 80° x 60° dispersion, as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Side feel Speaker 8" Installation Wall speakers passive black Dispersion (H x V) -60 x 60 °, Load rating (RMS) - 120 W, Frequency response - 50 - 20000 Hz, SPL (1W/1m) - 93 dB, Max. SPL - 114 dB, Impedance - 8 Ohm(s), as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Class H Power Amplifier 2 x 800 W 2 Ohms, 2 x 650 W 4 ohms, 2 x 450 W, 8 ohms, Frequency response - 20 - 20000 Hz, Signal-to-noise ratio - 106 dB for FOH speaker, as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Class D Power Amplifier 700W 2 x 350 W 4 Ohms, 2 x 200 W - 8ohms, Frequency response - 20 - 20000 Hz, for side feel speakers as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of DSP based 4 channel audio amplifier, 120 watts per channel @100V, 4 balance line inputs, ,4 speaker outputs, with terminal block as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Wireless Microphone System with Bodypack and Lavalier Microphone Transmission frequency range - 584 - 608 MHz, Frequency response - 25 - 16,000 Hz,Channels - 12, Antenna inputs , Signal-to-noise ratio - 104 dB, Max. output level - -10dbu with rack mount kit. as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Wireless Microphone System with Handheld Microphone Transmission frequency range - 584 - 608 MHz or equivalent, Frequency response - 25 - 16,000 Hz or equivalent , Minimum Channels - 12, Antenna inputs , Signal-to-noise ratio - 104 dB, Max. output level - -10dbu as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of Podium gooseneck microphone Frequency response - 40 Hz to 20 kHz, pick-up pattern - cardoid, Maximum sound pressure level - 130 dB SPL, with base mount shocket as per technical specification etc. as required.
Supplying, installing, testing and commissioning of 12 Channel analog audio Mixing Console with DFX and Compressor, input 6 microphone, 4 stereo line inputs, and 12 mono input, two master XLR output, Mono Mic Input Frequency Range - 10 - 45000 Hz, Mono Mic Input S/N Ratio - 113 dB as per technical specification etc. as required.
Supply, Laying, Testing and Commissioning of Ultra Flexible High Speed HDMI Cables HDMI Cable 1.5 Meter HDMI 2.0 Cable Male to Male, support Deep Color, 4K 4096 x 2160 @60Hz; 3840 x 2160 @ 60Hz 4:4:0, Minimum conductor gauge - 30AWG, gold Plating, as per technical specification etc. as required.
Supply, Laying, Testing and Commissioning of Ultra Flexible High Speed HDMI Cables HDMI Cable 20 Meter HDMI 2.0 Cable Male to Male, support Deep Color, 4K 4096 x 2160 @60Hz; 3840 x 2160 @ 60Hz 4:4:0, Minimum conductor gauge - 30AWG, gold Plating, as per technical specification etc. as required.
Supply, Installation, Testing and Commissioning of VGA Cable with audio cable 1.5mtr molded 15−pin HD and 3.5mm connectors at both ends as per technical specification etc. as required.
Supply, Laying of Shielded Twisted Pair (STP) 4Pairs 24 AWG Cable with connector, as per technical specification etc. as required.
Supply, Laying, Testing and Commissioning of Two 16 AWG conductors non- plenum Speaker Cable, for High performance cable for audio signals as per technical specification etc. as required.
Supply, Laying, Testing and Commissioning of Dual 20 AWG shielded twisted pairs with individual drain wires for Mic and Controlling Purpose, as per technical specification etc. as required.
05-FIRE FIGHTING WORK Supply, Installation, Testing and Commissioning of Electric driven Terrace pump suitable for automatic operation and consisting of following: complete in all respect as required. a) Horizontal, centrifugal, end suction pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal and flow of 900 lpm at 40m.head conforming to IS standards. b) Squirrel cage induction motor with suitable HP with synchronous speed 3000 RPM, Suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class-F insulation, Conforming to IS standards. c) Common Base plat for Pump and motor and coupling, coupling guard, vibration pad, cables and other accessories as required for complete installation of pump set.
Supply, Installation, Testing and Commissioning of 150 mm dia Pressure Gauge of range 0 - 15 Kg / cm² conforming to IS - 3624 having bourdon tube of stainless steel 316 in cast aluminium, stove enameled, black, weather proof case with outer, screwed aluminium bezel and complete with necessary U-type stainless steel siphon tube and cock including providing suitably painted angle iron support to the tube etc.as per specification complete as required.
M.S. Above Ground Pipe Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia.
M.S. Above Ground Pipe Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia.
M.S. Above Ground Pipe Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia
M.S. Under Ground Pipe Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and laying underground including one coat of anticorrosive primer and wrapping material of 4mm thick & 150 mm width protection coating as per IS:10221 by thermo fusion process,overlap shall be maintained at 15mm as per specifications complete as required: 100 mm dia.
M.S. Under Ground Pipe Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and laying underground including one coat of anticorrosive primer and wrapping material of 4mm thick & 150 mm width protection coating as per IS:10221 by thermo fusion process,overlap shall be maintained at 15mm as per specifications complete as required: 80 mm dia
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100 mm dia.
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia.
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dia.
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal
Supply, Installation, Testing and Commissioning of Fire Hose Cabinet of size 750mmx600mx250mm fabricated from 18 swg thick MS sheet with 6mm thick glazed hinged type centre opening doors having locking arrangement suitable for accommodating 2 nos RRL hose pipes, 1 no. nozzle, branch pipe & painting with two coats of anti-corrosive primer and two coats of approved red enamel paint etc. complete as required.
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 1)20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 2)20 mm nominal internal dia gun metal globe valve & nozzle. 3)Drum and brackets for fixing the equipmets on wall. 4)Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
Providing and fixing standard fireman Axe with heavy duty insulated rubber handle as per IS: 926 with clamps.
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe
Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve with necessary fittings. Size: 25 mm (For Riser)
Supply, installation, testing and commissioning of Pump on/off Remote switches to each internal hydrant valve with required accessories.
Supply, installation, testing and commissioning of XLPE insulated copper armoured Cable from each Pump on/off switches to Panel with all necessary accessories. Size: 4 core x 2.5 sq. mm
Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. For 4.5 Kg Capacity
Supply, installation, testing and commissioning of ABC type 6 kg Fire Extinguisher confirm to IS:15683, with ISI marked / TAC approved fitted with required accessories including wall suspension brackets.
Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes: Fire Equipment: 4" x 12"
Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes: In case of Fire, do not use lift, use staircase: 8" x 8"
Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes: Fire Lift: 4" x 12"
Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes: Fire Exit: 4" x 12"
Getting Approval/NOC of Fire protection system from local fire authority and any other relevant statutory authority at initial and various other stages of work, including preparation of report/drawings as per fire authority.
06-HVAC WORKS SUB HEAD 'MW-01' - MACHINERY Sec.1.0 Variable Refrigerant Volume System work Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 10.0 H.P. ( 8.33 TR)
Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 12.0 H.P. ( 10.0 TR)
Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 14.0 H.P. ( 11.5 TR)
Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 16.0 H.P. ( 13.33 TR)
Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 18.0 H.P. ( 15.0 TR)
Supply, Installation, testing and commissioning of Variable refrigerant volume system with Modular outdoor units having inverter driven multi scroll/Rotary compressors/ Digital scroll compressors (minimum two compressors) with one capacity controlling compressor and other constant speed type compressor working on R-410 A refrigerant, special pre- coated fins, panel, corrosion resistant (suitable for seaside installation) coated condenser, DC inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units, having following capacities. Out-door units 20.0 H.P. ( 16.5 TR)
In-door units Ceiling Mounted Four Way Cassette Type 3.0 TR
In-door units Ceiling Mounted Four Way Cassette Type 2.5 TR
In-door units Ceiling Mounted Four Way Cassette Type 2.0 TR
In-door units Ceiling Mounted Four Way Cassette Type 1.5 TR
In-door units Ceiling Mounted Four Way Cassette Type 1.0 TR
In-door units Hi-wall mounted type units 2.0 TR
In-door units Hi-wall mounted type units 1.5 TR
In-door units Hi-wall mounted type units 1.25 TR
In-door units Hi-wall mounted type units 1.00 TR
In-door units Ceiling Mounted One Way Cassette Type 1.0 TR
In-door units Ceiling Mounted One Way Cassette Type 1.5 TR
In-door units Ceiling Mounted One Way Cassette Type 2.0 TR
Remote control Cordless remote controllers
Remote control Central Remote Controller suitable up to 54 H.P. system
Copper Refrigerant distribution joints Refnet joint suitable up to 6 H.P. Indoor units-( 4.8 TR )
Copper Refrigerant distribution joints Refnet joint suitable up to 8 H.P. Indoor units-( 6.40 TR )
Copper Refrigerant distribution joints Refnet joint suitable up to 10 H.P. Indoor units ( 8.0 TR )
Copper Refrigerant distribution joints Refnet distribution joint for 10 H.P. to 20 H.P.
Copper Refrigerant distribution joints Refnet distribution joint for 21 H.P. to 38 H.P.
Copper Refrigerant distribution joints Refnet distribution joint for 39 H.P. to 64 H.P.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1/4" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 3/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1/2" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 5/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 3/4" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 7/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1-1/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1-3/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1-1/2" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1-5/8" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 1-3/4" O.D.
Refrigerant piping length A.C. Machine 18 Gauge hard drawn copper pipe including necessary fittings i.e. elbows, couplings, reducers etc. 2-1/8" O.D.
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1/4" O.D. -13mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 3/8" O.D. -13mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1/2" O.D. -13mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 5/8" O.D. - 19mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 3/4" O.D.- 19mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 7/8" O.D.- 19mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1" O.D. - 19mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1-1/8" O.D. - 25mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1-3/8" O.D. - 25mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1-1/2" O.D. - 25mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1-5/8" O.D. - 25mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 1-3/4" O.D. - 25mm thick
Refrigerant piping insulation For Suction line with following Thickness Nitrile rubber class 'O' insulation length. 2-1/8" O.D.- 32mm thick
Supply, installation, testing & commissioning of control and communication cabling between the indoor and outdoor units in the rigid PVC conduit. 2 core x 1 sq.mm steel braided twisted shielded wire
Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 2700 CFM / 40mm Static Pressure for Toilet
Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 1000 CFM / 40mm Static Pressure for Toilet
Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 2250 CFM / 65mm Static Pressure for Toilet
Floor / Loft Mounted Dry Scrubber for Kitchen Exhaust Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Floor / Loft mounted cabinet type Scrubber unit with DIDW Backward curved Centrifugal fan as per specification with drive & drive package of following capacities. The unit shall be with Starter panel. 7000 CFM / 50mm Static Pressure for Kitchen
Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 1600 CFM / 50mm Static Pressure for Wash & Garbage Area, Dirty Dish Collection
Supply, Installation, Testing & Commissioning of ceiling suspended type Inline Fresh Air Fan, as per specifications : 1100 CFM / 25mm Static Pressure
Supply, installation, testing and commissioning of Tube Axial fans complete with Hot dipped Galvanised Steel Casing, adjustable pitch die cast aluminium impeller (Hub and blades), motors with VFD & spun flanges on both ends. Casing position shall be as per the job requirement and shall be marked on the fan assembly. Fan inlet & outlet side fire rated canvass connections & non return dampers to be required. All other fan Floor mounting accesories will be provide with the fan. Electrical Starter Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, command, Automanual Status, fire status controlling, contacts for remote operation through Operating Panels, BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan, inside light and duly internally wired and tested. 8000 CFM / 25mm Static Pressure for STP
Providing and erecting approved make split air-conditioning unit consisting of condensing unit with fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by means of proper insulated copper tubing up to 5 RMT suitable for (Cost includes M.S. Stand, Gas Charging & Internal Copper Wiring & Remote Control) for 2 ton capacity - For 3 Star Rating
SUB HEAD 'MW-03' - Ducting, Grills, Diffuser and Insulation Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 24 Gauge
Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 22 Gauge
Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 20 Gauge
Supplying and erecting G.S.S. sheet metal complete with all accessories viz. anchor fastners, black painted, M.S. Angle / rod support, self adhesive 3mm thick rubber gasket galvanised hardware, double canvas connection with 6" Zip. ducting with various gauges mentioned as below to be used as per IS - 655 18 Gauge
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 Gauge
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 Gauge
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 20 Gauge
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 18 Gauge
Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.
Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications
Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.
Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.
Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers as per specification.
Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire damper
Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuater
Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.
Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm
Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 25mm
Supplying and fixing of following thickness ( Exposed to Atmosphere ) closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. And above Bonded Treated Woven Glass Fibre for Outer covering of Insulation Material GC bonded applied by suitable adhesive. Density: 200 +/- 20 gsm Thickness: 0.18 mm / 7 mill, The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm
Supplying and fixing of following thickness ( Exposed to Atmosphere ) closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. And above Bonded Treated Woven Glass Fibre for Outer covering of Insulation Material GC bonded applied by suitable adhesive. Density: 200 +/- 20 gsm Thickness: 0.18 mm / 7 mill, The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 25mm
Supply & Installation of Under Deck Insulation with Class ‘O’ Nitrile Rubber with tough Aluminum foil facing & as per detail specifications - 20mm
Supply & Installation of Under Deck Insulation with Class ‘O’ Nitrile Rubber with tough Aluminum foil facing & as per detail specifications - 25mm
SUB HEAD 'MW-04' - Miscelleneous works Extra charges for the Items length For Single phase Split A.C. Machine insulated pair of soft, copper tubing including power and control cable up to 2 TR capacity
Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. 50 mm dia.
Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. 40 mm dia.
Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. 32 mm dia.
Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. 25 mm dia.
Rigid PVC drain pipe of 10 Kg/cm2. rating with 9 mm thk.nitrile rubber insulation. 19 mm dia.
SUB HEAD 'MW-05' - Maintenance Works SYSTEM OPERATION & MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 1st Year after DLP
SYSTEM OPERATION & MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 2nd Year after DLP
SYSTEM MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 3rd Year after DLP
SYSTEM MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 4th Year after DLP
SYSTEM MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 5th Year after DLP
08-KITCHEN EQUIPMENTS: Providing and installing Platform Trolley (DS01) of size 900 x 600 x 900 as per technical specification
Supplying, installing, testing and commssioning Weighing Scale (DS02) (Floor Model) of 300 kg capacity as per technical specification.
Providing and installing SS Dunnage rack (DS03) of size 1200 x 600 x 300 as per technical specification.
Providing and installing St. Steel Storage Rack (4-Shelves) (MS01) of size 1100 x 550 x 1650 as per technical specification.
Providing and installing Two tire trolley (kitchen utility trolley) (MS02) of size 900 x 500 x 900 as per technical specification
Providing and installing onion potato bin (WT01) of size 1000 x 600 x 1000 as per technical specification.
Supplying, installing, testing and commssioning Potato Peeler (WT02) of 20 KG Capacity as per technical specification.
Supplying, installing, testing and commssioning Pulverizer (WT03) of 3HP Capacity as per technical specification.
Providing and installing Work Table with U/s and splash back (WT04) of size 1200 mm x 600 mm x 850 mm + 150 mm as per technical specification
Supplying, installing, testing and commssioning Dough kneading machine (WT05) of 25kg Capacity as per technical specification.
Supplying, installing, testing and commssioning 2 Door vertical refrigerator (VC01) of 500L Capacity as per technical specification.
Supplying, installing, testing and commssioning 2 Door vertical freezer (VC02) of 500L Capacity as per technical specification.
Providing and installing Work table with sink , u/s and splash back (VC03) of size 1800 x 600 x 850 + 150 as per technical specification.
Providing and installing Work table with u/s and splashback (VC04) of size 1500 x 600 x 850 + 150 as per technical specification.
Providing and installing Work table with sink and splashback (VC05) of size 1100 x 600 x 850 + 150 as per technical specification.
Providing and installing Side table with u/s and splashback (CK01) of size 600 x 750 x 850 + 150 as per technical specification.
Supplying installing, testing and commssioning Single Burner Indian Cooking Range (CK02) of size 600 x 600 x 450 as per technical specification.
Providing and installing Side table with u/s and splashback (CK03) of size 1000 x 750 x 850 + 150 as per technical specification.
Supplying installing, testing and commssioning Kadhai Fryer (CK04) of size 600 x 600 x 750 as per technical specification.
Supplying, installing, testing and commssioning Chapati plate puffer (CK05) of size 1500 x 600 x 850 as per technical specification.
Providing and installing Marble top chapati rolling table (CK06) of size 1800 x 600 x 850 as per technical specification.
Providing and installing Support table with u/s and splash back (CK07) of size 1800 x 600 x 850 + 150 as per technical specification.
Providing and installing Masala Trolley ( 8nos 1/6 GN Pan ) (CK08) of size 850 x 500 x 900 as per technical specification
Providing and installing Dosa Plate (CK09) of size 1000 x 600 x 850 as per technical specification
Providing and installing Side table with u/s and splashback (CK10) of size 600 x 600 x 850 + 150 as per technical specification.
Providing and installing Idli steamer with Boiler plant (CK11) of 120 Idli capacity as per technical specification.
Providing and installing thali counter with service rail and sneeze guard (SR01) of size 1200 x 650 + 300 x 850+450 as per technical specification.
Providing and installing Bain marie with 4Nos hot 1/1 GN pan, 1Nos ambient 1/1 GN pan,service rail and sneeze guard (SR02) of size 2200 x 650 + 300 x 850 + 450 as per technical specification.
Providing and installing Soiled dish table with scraping hole (DW01) of size 2100 x 750 x 900 as per technical specification.
Providing and installing Two sink pre-wash unit (DW02) of size 1800 x 750 x 900 as per technical specification.
Providing and installing Pre-rinse shower (T & S or equivalent make) (DW03) as per technical specification.
Supplying, installing, testing and commssioning Hood type dish washer machine (Electrolux or equivalent make) (DW04) of capacity 80rack/ hr as per technical specification.
Providing and installing Clean dish landing table (DW05) of size 1200 x 750 x 900 as per technical specification.
Providing and installing 4 shelves Clean dish storage rack (DW06) of size 1100 x 550 x 1650 as per technical specification.
Providing and installing Waste bins of 80 Ltr. Capacity (Garbage bin - Nilkamal) (DW07) as per technical specification.
Providing and installing SS Drain trough with perforated basket and pipe gratings (FD01) of size 1200 x 600 x 100 as per technical specification.
Supplying, installing, testing and commssioning Hosereel (FD02) of capacity 15m as per technical specification.
Supplying, installing, testing and commssioning Exhaust Hood with Baffle filter (EX01) of size 1500 x 900 x 500 as per technical specification.
Supplying, installing, testing and commssioning Exhaust Hood with Baffle filter (EX02) of size 750 x 900 x 500 as per technical specification.
Supplying, installing, testing and commssioning Exhaust Hood with Baffle filter (EX03) of size 1000 x 900 x 500 as per technical specification.
Supplying, installing, testing and commssioning Exhaust Hood with Baffle filter (EX04) of size 600 x 900 x 500 as per technical specification.
Supplying and installing GI Ducting for Exhaust Air as per technical specification.
Supplying and installing GI Ducting for Exhaust Air with air grill as per technical specification.
Supplying, installing, testing and commssioning Exhaust air blower of 7000 CFM as per technical specification.
Supplying, installing, testing and commssioning Fresh air blower of 4200 CFM as per technical specification.
SHANTI PROCON LLP
P.R. Patel and Co.
TIRUPATI SARJAN LIMITED
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid