Construction of District Police Office Building (B.W) atSuryapet of Suryapet District Sub Work: Providing Electrical Panel Room at DPO Suryapet(2nd Call)

EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308).

CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATIONS & UNDER STONE SLAB FLOORING .(APSS NO: 402).

RE-FILLING WITH USEFUL AVAILABLE EXCAVATED EARTH OTHER THAN EXPANSIVE SOILS LIKE RED EARTH AND ORDINARY GRAVEL ETC., (EXCLUDING ROCK) IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES , HIRE CHARGES OF T & P ETC., BUT EXCLUDING GST - COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

FILLING WITH CARTED GRAVEL IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES, HIRE CHARGES OF T & P ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST, COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

FILLING WITH SAND IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES, HIRE CHARGES OF T & P ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST, COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310)

VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR FOOTINGS (APSS NO.403)

VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR PEDESTALS (APSS NO.403)

VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR PLINTH BEAMS (APSS NO.403)

VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR COLUMNS GF (APSS NO.403)

MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR WALLS OF 225MM THICK GROUND FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504)

PROVIDING "HYSD/TMT" STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM Reinforcement Steel (HYSD/TMT) from steel Manufactureres within Telangana with min integrated installed Production Capacity of 2 Lakh MT per annum like AF Star TMT/MS Life TMT, Radha TMT, Sugna TMT FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED.

PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR GROUND FLOOR (APSS NO: 901&904)

FLOORING WITH NANO POLISHED / STAIN FREE SOLUBLE SALT / STAIN FREE PORCELAIN VITRIFIED TILES SCREEN PRINTED OF SIZE 600 X 600 MM and thickness between 8-10 mm 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, , ETC., COMPLETE FOR FINISHED ITEM OF WORK

PAINTING TO NEW WALLS WITH THREE (3) COATS OF Synthetic Polymer luxury Plastic emulsion /solvent based lustre paint of superior grade having (VOC < 50 Gms./Lit) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK (APSS NO. 911)

PAINTING WITH Acrylic Emulsion paint Exterior grade silicon additives having (VOC < 50 Gms/Lit) OF APPROVED MAKE AND COLOUR TO THE EXTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 Ml OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION Etc., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK (APSS NO:908).

PROVIDING, SUPPLYING & FIXING OF FIXED LOUVERED VENTILATOR MADE OUT OF MULTI CHAMBERED UPVC SECTIONS WITH GLAZING BEAD SHALL BE CO-EXTRUDED WITH GREY COLOUR SOFT PVC. HAVING ISOLATED DRAINAGE AND REINFORCED WITH GALVANIZED IRON PROFILES THROUGHOUT THE WINDOW. THE OUTER FRAME HAVING AN OVERALL SIZE OF 60 MM X 55 MM X 2.40 WITH REINFORCEMENT OF 1 MM THICKNESS AND MULLION WITH OVERALL SIZE OF 74 MM X 60 MM X 2.40 MM WITH REINFORCEMENT OF 1 MM THICKNESS. (COMPOSITION OF PROFILE SHALL CONSISTS A MINIMUM OF 5.5 PHR OF TIO2 AND NOT MORE THAN 12PHR OF CACO3 FOR EVERY 100 PARTS OF PVC RESIN).VENTILATOR SHALL BE PROVIDED WITH 4.5 MM PIN HEAD GLASS, STANDARD HARDWARE. WALL THICKNESS OF FRAME & MULLION SHALL BE 2.4 MM.,INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, ACCESSORIES, LABOUR CHARGES FOR TRANSPORTATION, ERECTION AT SITE, BUT EXCLUDING GST COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLYING MS STRUCTURAL STEEL WORKS LIKE HEAVY STEEL WORKS LIKE TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS INCLUDING COST OF WELDING RODS, POWER CHARGES, FOR ERECTING & FIXING ALL STRUCTURAL STEEL WORKS LIKE HEAVY IRON GRILLS, TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS ERECTING IN POSITION AND FIXING BY USING CHAIN PULLEY BLOCKS, DEREK POLE ARRANGEMENTS AND CRANES ETC., COMPLETE IN POSITION ETC COMPLETE FOR ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK

PAINTING TO NEW IRON WORK WITH ONE COAT OF RED OXIDE PRIMER COAT AND TWO COATS WITH SYNTHETIC ENAMEL PAINT OF APPROVED BRAND AND SHADE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES INCLUDING PUTTY, ALL INCIDENTAL, OPERATIONAL CHARGES ETC., COMPLETE (THE RATE INCLUDES TWO COATS OF PAINT AND ONE COAT PRIMER) BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK IN ALL FLOOR. (APSS NO.1201, 1207, 1212)

ROOFING:ROOFING WILL BE PROVIDED WITH 0.5MM THICK GALVANIZED / PRE PAINTED G.I. PROFILED SHEETS FIXED TO THE PURLINS WITH 14 SIZE SELF DRILLING SCREWS WITH NEOPRENE WASHER. SIDE LAPS ARE STITCHED WITH SELF TAPPING / DRILLING SCREWS. END LAPS ARE TO BE SEALED WITH 25X3 MM BUTYL TAPE. THE SHEETS ARE PROVIDED WITH ANTI CAPILLARY GROVE COMPLETE FOR FINISHED ITEM OF WORK.

SUPPLY & FIXING OF ROLLING SHUTTER MADE OF 80 X 1.25 MM MACHINE ROLLED CRCA LATHS, INTERLOCKED TOGETHER THROUGH THEIR ENTIRE LENGTH AND JOINTED TOGETHER AT THE ENDS BY END-LOCKS, MOUNTED ON SPECIALLY DESIGNED PIPE SHAFT OF 50MM DIAMETER NOMINAL BORE MS B CLASS PIPE WITH BRACKETS, PLATES, GUIDE CHANNELS, STOPPERS, BOTTOM LOCKING PLATES AND ARRANGEMENTS FOR INSIDE & OUTSIDE LOCKING WITH PUSH-PULL OPERATIONS INCLUDING COST OF HOOD COVER AND SPRINGS COMPLETE, PAINTED WITH ONE COAT OF APPROVED STEEL PRIMER, LOCKS, BALL BEARINGS, ALL ACCESSORIES ETC COMPLETE FOR FINISHED ITEM OF WORK AS PER SPECIALSPEC:1108

SUPPLY AND FIXING OF ISI 25MM OUTER DIA HEAVY GRADE WITH IS:9537 PART 3 RIGID PVC PIPE CONCEALED IN ROOF SLABS WITH ALL REQUIRED ACCESSORIES INCLUDING LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKES : SUDHAKAR / MODI / VIP/ PRECISION.

SUPPLY AND FIXING OF ISI 25MM OUTER DIA HEAVY GRADE WITH IS:9537 PART 3 RIGID PVC PIPE CONCEALED IN WALL WITH ALL REQUIRED ACCESSORIES [LIKE 'U' NAILS, JUNCTION BOX, PVC BENDS AND CEMENT] INCLUDING MASONARY WORK FOR LIGHT, FAN, COMMON, SEPARATE PLUG POINT AND SWITCH/POWER BOARDS ETC., INCLUDING ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKES: SUDHAKAR / MODI / VIP / PRECISION.

SUPPLY AND FIXING OF ISI 25MM OUTER DIA HEAVY GRADE WITH IS:9537 PART 3 RIGID PVC PIPE CONCEALED IN UNDERNEETH THE FLOOR WITH ALL REQUIRED ACCESSORIES INCLUDING MASONARY WORK AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKES: SUDHAKAR / MODI / VIP / PRECISION.

WIRING WITH 2 RUNS OF 1.5 SQMM FRLSH / HFFR PVC INSULATED 1100V GRADE AS PER IS:694/2010, IS 17048 SPECIFICATION FOR COPPER CABLE IN EXISTING PIPE WITH 6A / 10A 1 WAY 1 MODULE MODULAR SWITCH CONTROL WITH SUITABLE MODULE HOT DIP GALVANIZED MODULAR TYPE METAL BOX COVERED WITH SUITABLE MODULAR COVER FRAME, WITH 3 PLATE JUMBO CEILING ROSE INCLUDING ALL LABOUR CHARGES ETC., COMPLETE FOR LIGHT AND BELL POINTS IN NON-RESIDENTIAL BUILDINGS BUT EXCLUDING GST. COPPER CABLE MAKE: FINOLEX / HAVELLS / POLYCAB. MODULAR SWITCH, SOCKET, METAL BOX & COVER FRAME MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS/GOLD MEDAL CURVE. CEILING ROSE MAKE: GOLD MEDAL OLIVE / MILLION ZOOM / ANCHOR PENTA CHERRY.

WIRING WITH 3 RUNS OF 1.5 SQMM FRLSH / HFFR PVC INSULATED 1100V GRADE AS PER IS:694/2010, IS 17048 SPECIFICATION FOR COPPER CABLE IN EXISTING PIPE WITH 6A / 10A 1 WAY 1 MODULE MODULAR SWITCH CONTROL WITH SUITABLE MODULE HOT DIP GALVANIZED MODULAR TYPE METAL BOX COVERED WITH SUITABLE MODULAR COVER FRAME, WITH 3 PLATE JUMBO CEILING ROSE INCLUDING ALL LABOUR CHARGES ETC., COMPLETE FOR CEILING AND EXHAUST FAN POINTS IN NON-RESIDENTIAL BUILDINGS BUT EXCLUDING GST. COPPER CABLE MAKE: FINOLEX / HAVELLS / POLYCAB. MODULAR SWITCH, SOCKET, METAL BOX & COVER FRAME MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS/ GOLD MEDAL CURVE. CEILING ROSE MAKE: GOLD MEDAL OLIVE / MILLION ZOOM / ANCHOR PENTA CHERRY.

SUPPLY AND FIXING OF 6 / 10A 3/2 PIN 2 MODULE MODULAR SOCKET WITH SHUTTER. WITH 6 / 10A 1 WAY 1 MODULE MODULAR SWITCH CONTROL ON A COMMON SWITCH BOARD WITH SUITABLE MODULE HOT DIP GALVANIZED MODULAR METAL BOX COVERED WITH SUITABLE MODULAR COVER FRAME WITH EARTH CONTINUITY INCLUDING WIRE LEADS, EARTH CONNECTIONS ALONG WITH ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MODULAR SWITCH, SOCKET, METAL BOX & COVER FRAME MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS / GOLD MEDAL CURVE.

SUPPLY AND FIXING OF 20A 2 MODULE MODULAR SOCKET WITH SHUTTER AND 16A / 20A 1 WAY 1 MODULE MODULAR SWITCH DULY RECESSED IN WALL WITH 3 MODULE HOT DIP GALVANIZED MODULAR METAL BOX SIZE COVERED WITH 3 MODULAR COVER FRAME INCLUDING EARTH CONNECTIONS AND ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. [POWER PLUG] MODULAR SWITCH, SOCKET, METAL BOX & COVER FRAME MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS / GOLD MEDAL CURVE.

SUPPLY AND FIXING OF 10A 3/2 PIN 2 MODULE MODULAR SOCKET WITH SHUTTER-2 NOS AND 6A / 10A 1 WAY 1 MODULE MODULAR SWITCH CONTROL-2NOS DULY RECESSED IN WALL WITH SUITABLE MODULE HOT DIP GALVANIZED MODULAR METAL BOX SIZE COVERED WITH SUITABLE MODULAR COVER FRAME INCLUDING EARTH CONNECTIONS AND ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. [2 SOCKET BOARD] MODULAR SWITCH, SOCKET, METAL BOX & COVER FRAME MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS / GOLD MEDAL CURVE.

SUPPLY AND FIXING OF CAT 6 RJ-45 INFORMATION OUTLETS INCLUDING DUEL FACE PLATE ON 2 MODULAR HOT DIP GALVANIZED METAL BOX INCLUDING GIVING CONNECTIONS, COST OF ALL ACCESSORIES AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. I/O & DUEL FACE PLATE MAKES: D LINK / AMP / MOLEX / LEGRAND / KRONE. METAL BOX MAKE: LEGRAND / HAVELLS / GM / ANCHOR.

SUPPLY AND FIXING OF MODULAR SOCKET TYPE TELEPHONE JACK WITH CONNECTOR ON 2 MODULAR HOT DIP GALVANIZED METAL BOX AND 2 MODULAR COVER FRAME INCLUDING GIVING CONNECTIONS, COST OF ALL ACCESSORIES AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. TELEPHONE JACK WITH CONNECTOR, COVER FRAME & METAL BOX MAKES: LEGRAND LYNCUS / HAVELLS FABIO / GM FOUR FIVE / ANCHOR ROMA PLUS.

SUPPLY AND RUN OF 3 OF 2.5 SQMM FRLSH / HFFR PVC INSULATED 1100V GRADE AS PER IS:694 / 2010, IS 17048 SPECIFICATION FOR COPPER CABLE IN EXISTING PIPE FOR 2 RUNS OF MAINS & 1 RUN OF EARTH CONTINUITY INLCUDING ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKE: FINOLEX / HAVELLS / POLYCAB.

SUPPLY AND RUN OF 3 OF 4.0 SQMM FRLSH / HFFR PVC INSULATED 1100V GRADE AS PER IS:694 / 2010, IS 17048 SPECIFICATION FOR COPPER CABLE IN EXISTING PIPE FOR 2 RUNS OF MAINS & 1 RUN OF EARTH CONTINUITY INLCUDING ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKE: FINOLEX / HAVELLS / POLYCAB.

SUPPLY AND RUN OF LAN CABLE CAT - 6 UTP CABLE IN EXISTING PVC CONDUIT INCLUDING COST AND CONVEYANCE OF ALL MATERIALS AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKES: D LINK / AMP / MOLEX / LEGRAND / KRONE.

SUPPLY AND RUN OF 2 PAIR, 0.5MM TELEPHONE COPPER WIRE IN EXISTING PVC CONDUIT INCLUDING COST AND CONVEYANCE OF ALL MATERIALS AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST. MAKES: FINOLEX / DELTON / SURABI / POLYCAB.

SUPPLY, TRANSPORTATION OF ENERGY EFFICIENT FAN, 1200 MM SWEEP, ALUMINIUM BODY, CONSUMING 28 W, BEE 5 STAR RATED, CEILING FAN WITH BRUSH LESS DIRECT CURRENT (BLDC) MOTOR, CLASS OF INSULATION: B, 3 NO'S BLADES, 30 CM LONG DOWN ROD, 2 NO'S CANOPIES, SHACKLE'KIT, COPPER WINDING, POWER FACTOR GREATER THAN 0.90, SERVICE VALUE (CMMAV) GREATER THAN 8.0, AIR DELIVERY MINIMUM 235 CMM, 350 RPM (TOLERANCE AS PER IS:374-2019), THD LESS THAN 10%. WITH REMOTE OR COMPATIBLE TO ELECTRONIC STEP TYPE REGULATOR UNIT FOR SPEED CONTROL AND ALL REMAINING ACCESSORIES INCLUDING SAFETY PIN, NUT BOLTS, WASHERS, TEMPERATURE RISE=75°C(MAX), INSULATION RESISTANCE MORE THAN 2 MEGA OHM, SUITABLE FOR 230V, 50 HZ, SINGLE PHASE AC SUPPLY, EARTHING ETC., INCLUDING ALL STANDARD ACCESSORIES ETC., COMPLETE BUT EXCLUDING GST. MAKES : ATOMBERG (EFFICIO ) / HAVELLS / ORIENT / HALONIX / CROMPTON.

SUPPLY OF 2 MODULE MODULAR TYPE ELECTRONIC FAN REGULATOR WITH 2 MODULE HOT DIP GALVANIZED MODULAR METAL BOX COVERED WITH 2 MODULAR COVER FRAME ETC., COMPLETE BUT EXCLUDING GST. MAKE: LEGRAND LYNCUS / GM FOUR FIVE / ANCHOR ROMA PLUS / GOLD MEDAL CURVE.

LABOUR CHARGES FOR FIXING OF CEILING FAN AND REGULATOR INCLUDING TRANSPORTATION AND GIVING CONNECTIONS WITH TWIN CORE WIRE ETC., COMPLETE BUT EXCLUDING GST.

SUPPLY AND FIXING OF 12 / 15 MS PLAIN ROD FAN HOOK WITH ALL REQUIRED ACCESSORIES ETC., COMPLETE BUT EXCLUDING GST.

SUPPLY AND ERECTING 19/20MM STEEL TUBE DOWN ROD OF 2 FEET LENGTH WITH BOLTS & NUTS DULY PAINTED WITH MATCHING COLOUR OF FAN ETC., COMPLETE BUT EXCLUDING GST.

SUPPLY OF 10" (250MM) RPM BLDC EXHAUST FAN WITH NECESSARY ACCESSORIES ETC., COMPLETE BUT EXCLUDING GST. MAKE : ATOMBERG / CROMPTON / HAVELLS / ORIENT.

LABOUR CHARGES FOR FIXING OF BLDC EXHAUST FAN IN WALL WITH NECESSARY CONNECTIONS ETC., COMPLETE BUT EXCLUDING GST. (FOR HOLE ALREADY MADE AVAILABLE)

SUPPLY AND TRANSPORTATION OF 20W +/- 10%, >/ 2000 LUMENS, 1200MM LENGTH LED RETRO TUBE LIGHT, HOUSING MADE WITH ALLUMINIUM ANODISED BODY, WIDE OPERATING VOLTAGE WITH DOUBLE SIDE CONNECTION, PF≥0.9, SURGE PROTECTION: > 2KV, THD<15%, WITH INBUILT DRIVER AND FROSTED COVER CCT: 3000K - 6500K AS DESIRED BY THE DEPARTMENT AND AS PER IS SPECIFICATIONS, MINIMUM CRI≥80 ETC., COMPLETE WITH 5 YEARS WARRANTY WITH BIS CERTIFICATION.LUMINAIRE MAKE: CROMPTON / HAVELLS / WIPRO. LED MAKE: : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM.

FIXING OF 20W LED TUBE LIGHT LUMINAIRE ON WALL / CEILING WITH ALL ACCESSORIES INCLUDING GIVING CONNECTIONS AND ALL LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST.

SUPPLY AND FIXING OF 4 WAY TPN DB HORIZONTAL WITH IP 43 PROTECTION AS PER IS:13032 AND SUITABLE FOR 12 NOS S.P. OUTGOINGS AND FOR 1 NO 4 POLE INCOMER (FP ISOLATOR / MCB) WITH 100 A TINNED COPPER BUSBAR, NEUTRAL BAR, EARTH BAR AND CABLE TIES FOR CABLE MANAGEMENT, FULLY SHROUDED NEUTRAL BAR, PROFILE BLANKING MODULES FOR UNUSED MCB WAYS, DIN BARS AND DETACHABLE GLAND PLATE ETC., COMPLETE WITH INTER CONNECTIONS BUT EXCLUDING GST. INCOMMER: 40A FP ISOLATOR - 1NO. OUTGOING: 6-32A SP MCB, 10KA ISI MARK - 12 NOS. DB MAKES: LEGRAND / SCHNEIDER / SIEMENS / LK (L&T). ISOLATOR MAKE: LEGRAND-DX3 / SCHNEIDER-ACTI9 / SIEMENS / LK (L&T) EXORA. MCB MAKE: LEGRAND-DX3 / SCHNEIDER-ACTI9 / SIEMENS / LK (L&T) EXORA.

SUPPLY OF 10 SQMM 4 CORE XLPE INSULATED, 1100V GRADE ARMOURED ALLUMINIUM CABLE WITH ISI MARK AS PER SPECIFICATION CONFIRMING TO IS:7098 (PART - I) BUT EXCLUDING GST. MAKE: TORRENT / UNIVERSAL / POLYCAB / HAVELLS / GLOSTER / KEI / FINOLEX.

EARTH WORK EXCAVATION OF TRENCH IN HARD GROUND SOIL, LAYING OF U.G CABLES FROM 70 SQMM TO 400 SQMM FOR LAYING OF HUME PIPES AND BACK FILLING OF TRENCH INCLUDING COST AND CONVEYANCE OF MATERIALS AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST.

LABOUR CHARGES FOR RUN OF U.G CABLE ON WALL / EXISTING PIPE WITH NECESSARY FIXING ARRANGMENTS SUCH AS SADDLES, CLAMPS,WOODEN SEPARATORS ETC., (AS DIRECTED BY DEPARTMENTAL OFFICIAL) ETC., COMPLETE BUT EXCLUDING GST.

PROVIDING INDEPENDENT EARTHING FOR IMPORTANT EQUIPMENT WITH 40MM DIA 'B' CLASS 2.5M LONG G.I PIPE AND 19MM DIA 'B' CLASS G.I PIPE OF 0.3MTR. LONG CONNECTED WITH REDUCER PROVIDING G.I FUNNEL WITH MESH ENCLOSED IN C.C/ BRICK MASSONRY CHAMBER OF 450M X 450M X 400MM WITH R.C.C. SLAB COVER DULY PROVIDING STAGGERED HOLES FILLING WITH 20KG SALT AND 40KG CHARCOAL OR 40KG BENTONITE POWDER FROM THE BOTTOM OF THE PIPE GIVING EARTH CONNECTION FROM ELECTRODE THROUGH G.I STRIP OF 40 X 6MM X 200MM LENGTH WITH ALL ACCESSORIES AND LABOUR CHARGES COMPLETE, AS PER IS SPECIFICATIONS 732/1982 (PART II) BUT EXCLUDING GST.

SUPPLY AND RUN OF NO. 8 SWG COPPER WIRE INCLUDING COST OF ALL ACCESSORIES AND LABOUR CHARGES ETC., COMPLETE BUT EXCLUDING GST.