Salem Division: Construction of New Terminal building at Erode Railway Station- Electrical arrangements.

1- Cable arrangement

Excavation of Cable trench in all kinds of soil including refilling as per Drg. No. CEE /CN/MS/01-2018.

Excavation of Cable trench across the concrete flooring / road / track as per Drg. No. CEE/CN/MS/01-2018.

Breaking of cement concrete flooring as instructed by Engineer-in-charge at site.

Supply and provision of mass concrete for platforms or elsewhere with 1:3:6 ratio using 20 mm blue metal complete in a manner as directed by the Section Engineer in charge at site.

Labour charges for laying of HDPE pipes 63 mm dia PN 6 and PE 100 type in excavated trenches, on walls, platforms, platform shelters or any other required location, complete 5 with suitable fixing arrangements and necessary coupling/jointing works, as directed by the Section Engineer-in-charge at site. The work includes handling, aligning, positioning, jointing and securing the HDPE pipes to ensure proper routing, protection and continuity. Note: Required HDPE pipes will be supplied by Railways.

Labour Charges for Laying of 110 mm Dia PE 100 PN 6 type HDPE pipes in the 6 excavated trench, on walls or on platform shelter etc., including suitable fixing arrangement complete in a manner as directed by Section Engineer-in-charge at site.(Note: Required HDPE Pipe will be supplied by Railways.)

Supply and fixing of medium duty GI pipe of 65 mm dia, conforming to IS.1239,part 1 (2004) ,for cable leading without clamp complete in an approved manner and as directed by Engineer in charge at site.

Supply and laying of 6 SWG GI wire along with the LTUG Cable, for earth continuity confirming to IS 12776 complete in an approved manner and as directed by Engineer in charge at site.

Supply and fixing of cable route indicator made of cast iron plate type as per specification in drawing No. CEE/CN/MS/11-2004 complete in an approved manner and as directed by Engineer in charge at site.

Labour charges for Laying, testing and commissioning of LTUG power cables of size 10 upto and including 50 sq.mm in the excavated trench/on Building walls/Sheds/Shelters etc., as per IS No:1255 complete in an approved manner and as directed by Engineer in charge at site. Note: LTUG Cables only will be supplied by Railways.

Labour charges for Laying, testing and commissioning of LTUG power cables size of 11 above 50 sq.mm and upto 185 sq.mm in the excavated trench/on Building walls/Sheds/Shelters etc., as per IS No:1255 complete in an approved manner and as directed by Engineer in charge at site. Note: Required LTUG Cable will be supplied by Railways.

Supply and termination and connection of LTUG cable of sizes upto 50 sqmm with 12 aluminium crimping sockets and single compression type cable gland.Note: One termination comprises of one number of single flange type brass cable gland and with four numbers of aluminium crimping sockets for all cores of the cable.

Supply and termination and connection of LTUG cable of sizes above 50 sqmm upto 13 and including 185sqmm size with aluminium crimping sockets and single compression type cable gland.Note: One termination comprises of one number of single flange type brass cable gland and with four numbers of aluminium crimping sockets for all cores of the cable.

Supply and provision of sealing compound for cable leading pipe for leading of cable of upto 50 sqmm.

Supply and provision of sealing compound for cable leading pipe for leading of cable of above 50 sqmm but up to and including 185 sqmm.

Fabrication, supply and fixing of clamps made out MS flats of different sizes for 16 fabrication of clamps for various requirements. The clamp shall be made out of MS flat of suitable size, painted with two coats in each of zinc chromate and grey enamel paint or suitable colour complete in an approved manner and as directed by Engineer in charge at site and using GI bolts with nuts of suitable size for fixing.

2-Power Supply arrangement

Supply and concealing of rigid PVC conduits of 20 mm Dia confirming to IS 17 9537/P3/1983 or latest (ISI marked) with wall thickness not less than 2.0mm along with the all accessories like bend, junction box etc and including cutting the wall/ceiling/chipping with re plastering and finishing the surface including painting to restore it to its original condition complete as directed by Engineer in charge at site.

Supply and fixing of PVC conduits of 20 mm Dia confirming to IS:9537/P3/1983 or 18 latest(ISI Marked) with wall thickness not less than 2.0 mm along with all accessories like bend,junction box etc on existing wall/stanchion/portal/column and clamped at regular intervals as directed by Engineer in charge at site.

Supply and concealing of rigid PVC conduits of 25 mm Dia confirming to IS 19 9537/P3/1983 or latest (ISI marked) with wall thickness not less than 2.0mm along with the all accessories like bend, junction box etc and including cutting the wall/ceiling/chipping with re plastering and finishing the surface including painting to restore it to its original condition complete as directed by Engineer in charge at site.

Supply and fixing of PVC conduits o f 25 mm Dia confirming to IS:9537/P3/1983 or latest(ISI Marked) with wall thickness not less than 2.0 mm along with all accessories like bend, junction box etc on existing wall/stanchion/portal/column and clamped at regular intervals as directed by Engineer in charge at site.

Supply and laying of ISI marked medium duty PVC rigid wiring conduit pipe of size 32 21 mm dia for open wiring including all accessories like tees,bends, junction box etc., on existing wall/stanchion/portal/column and clamped at regular intervals as directed by Engineer in charge at site.

Supply and wiring by 4 nos of 10.0 sq.mm (3 phase) PVC insulated FRLS type flexible 22 copper cable conforming to IS.No:694,1100 V grade with 1 no of 14 SWG tinned copper wire/10.0 sq.mm flexible copper cable through PVC conduit pipe already fixed. The Color coding shall be followed as directed by Engineer in charge at site(4 nos of 10.0 sq.mm copper cable and 1 no of 14 SWG tinned copper shall be taken as 1 Mtr for measurement purpose)

Supply and wiring (single phase) including termination by 3 nos. of 6 sqmm PVC 23 insulated FRLS type flexible copper cable conforming to IS. No: 694, 1100 V grade through PVC conduit already fixed by concealed/open manner. Color coding shall be followed as directed by Engineer in charge at site(3 nos. of 6 sqmm copper cable shall be taken as 1 Mtr for measurement purpose).

Supply and wiring (single phase) including termination by 3 nos. of 4 sqmm PVC 24 insulated FRLS type flexible copper cable conforming to IS. No: 694, 1100 V grade through PVC conduit already fixed by concealed/open manner. Color coding shall be followed as directed by Engineer in charge at site(3 nos. of 4 sqmm copper cable shall be taken as 1 Mtr for measurement purpose).

Supply and wiring (single phase) including termination by 3 nos. of 2.5 sqmm PVC 25 insulated FRLS type flexible copper cable conforming to IS. No: 694, 1100 V grade through PVC conduit already fixed by concealed/open manner. Color coding shall be followed as directed by Engineer in charge at site(3 nos. of 2.5 sqmm copper cable shall be taken as 1 Mtr for measurement purpose).

Supply and wiring (single phase) including termination by 3 nos. of 1.5 sqmm PVC 26 insulated FRLS type flexible copper cable conforming to IS. No: 694, 1100 V grade through PVC conduit already fixed by concealed/open manner. Color coding shall be followed as directed by Engineer in charge at site(3 nos. of 1.5 sqmm copper cable wire shall be taken as 1 Mtr for measurement purpose).

Supply and fixing of 3 plate ceiling rose with PVC junction Box on provision of PVC dummy sheet (heavy) complete in an approved manner and as directed by Engineer in charge at site.

Supply at site, fixing, testing and commissioning of 12 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the 28 following works at the location where the boxes are to be fixed: (1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 08 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the 29 following works at the location where the boxes are to be fixed: (1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 06 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the following works at the location where the boxes are to be fixed:(1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 04 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the 31 following works at the location where the boxes are to be fixed:(1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 03 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the 32 following works at the location where the boxes are to be fixed:(1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 02 way modular switch box with concealed metallic flush box as base, mounting plate (modular white plate) confirming to latest IS specification complete in an approved manner. The boxes are to be fixed firmly after doing the 33 following works at the location where the boxes are to be fixed:(1) Required opening for fixing the modular metallic switch box to be made by cutting the wall without causing major damage to wall (2) Unwanted projections are to be chipped and the wall surface is to be made even, (3) The wall surface is to be plastered to the present level of the wall surrounding the board. (4) The gap between box and wall surface to be filled with suitable filling material.

Supply at site, fixing, testing and commissioning of 1-way, 6 Amps modular switch, 34 conforming to the latest IS specifications, complete in all respects, to be provided on the existing modular switch boxes already erected, including making all internal wiring connections inside the modular switch box, in an approved manner, as directed by the Section-in-Charge.

Supply at site, fixing, testing and commissioning of 1-way, 16 Amps modular switch, 35 conforming to the latest IS specifications, complete in all respects, to be provided on the existing modular switch boxes already erected, including making all internal wiring connections inside the modular switch box, in an approved manner, as per the instructions of the Section-in-Charge.

Supply at site, fixing, testing and commissioning of Dummy plate suitable for modular box mentioned in the schedule No;28-33 wherever required with necessary fixing by suitable screws & nuts in approved manner as directed by the Engineer in-charge at site.

Supply at site, fixing, testing and commissioning of modular type 6A socket outlet (2/3 Pin, flush type) conforming to the latest IS specifications, complete in all respects, to be 37 provided on the existing modular boxes already erected, including internal wiring connection and provision of earth connection to the earth terminal in the switch board using 1.5 sq.mm PVC insulated single core copper conductor, in an approved manner, as per the instructions of the Section-in-Charge.

Supply at site, fixing, testing and commissioning of modular type 16A socket outlet (5/3 Pin, flush type) conforming to the latest IS specifications, complete in all respects, to be 38 provided on the existing modular boxes already erected, including internal wiring connection using 4.0 sq.mm PVC insulated single core copper conductor and providing earth connection to the earth terminal in the switch board, in an approved manner, as per the instructions of the Section-in- Charge.

Supply, Fixing, testing and commissioning of LED Batten light with complete fixtures 39 having 20W with available LED Efficacy of minimum 125 (Lumen / Watt), Color Temperature (in K) of 6500 (Cool white), Aluminum extruded housing, with Inbuilt Driver/Control gear, Ingress Protection of IP-20, Operating Voltage range of 100 to 300 V, Frequency 50 Hz with minimum 50000 burning hours and SPD> 4kV and above. The fitting shall be fixed with Round block with patterns on side wall/ceiling with wiring by 3C x 1.0 sqmm PVC insulated & sheathed round flexible copper cable in an approved manner as directed by Engineer in charge at site. The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no: 31

Supply, erection, testing, commissioning of Recess mounting type 20 W 1'x1' LED square fittings with suitable accessories for mounting. The fixture should be rigid, the mounting should be surface type on ceiling and operating voltage range of 100-300 VAC supply, frequency of 40 50 Hz +/-5%with minimum warranty of 5 years similar to PHILIPS make model No SM200CLED16S 6500 PSU OD WH or its equivalent . The fitting shall be fixed on ceiling including wiring by 3C x 1.0 sqmm PVC insulated & sheathed round flexible copper cable complete in an approved manner and as directed by Engineer in charge at site. The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no: 31.

Supply, erection, testing, commissioning of Surface mounting type 15W LED light fittings with suitable accessories for mounting,the square type fitting should have LED Efficacy of minimum 120 (Lumens/watt),4kV surge protection with 50000 burning hours with IP 54 protection. 41 The fixture should be rigid, the mounting should be surface type on ceiling and operating voltage range of 100-300 VAC supply, frequency of 50 Hz +/-5%. Fitting shall be fixed on ceiling including wiring by 3 C x 1.0 sqmm PVC insulated & sheathed round flexible copper cable in an approved manner as directed by the Engineer in charge at site. The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Fixing, testing and commissioning of Exhaust fan 300mm sweep including wall 42 opening, fixing of frame and plastering as required for housing. Exhaust fan including wiring with 3C x 1.0 sq.mm PVC insulated & sheathed copper flexible cable. Note: Necessary Exhaust fan only will be supplied by Railways.

Fixing, testing and commissioning of 1200 mm sweep BLDC fan in the existing fan 43 hook including wiring with 3 C X 1.0 sq.mm PVC insulated & sheathed copper flexible cable in an approved manner and as directed by Engineer in charge at site. (Note: BLDC fan only will be supplied by Railways.)

Supply and fixing of Angular/Batten holder with 9W LED Lamp with IS mark and the 44 LED lamp should be B22 lamp,90 lumens/watts,colour temperature 6500K including wiring and fixing on side wall/roof as per site requirement complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, erection and testing of L.T. Earthing arrangements duly stencilling of earth 45 resistance value along with date as per Drg. no. CEE/CN/MS/16-2004, including supply and spreading of salt and charcoal 5 kgs in each for earth treatment etc , including supply / leading / laying /burying and concealing of 4 SWG GI wire from earth electrode to proposed MDB / SDB or elsewhere in an approved manner as directed by Section Engineer in charge at site.

Supply and fixing of IP66 class powder coated metallic cable looping box of 250 x 300 46 x 150 mm size made of CRCA draw quality sheet steel 1.2 mm thickness similar to BCH make BIL 60020 with suitable fixing arrangement on wall/structures. The rate includes provision of hylum sheet of suitable size and 1 no of 100A 4 way terminal connectors and 2 nos of cable glands of suitable size as directed by the Engineer in charge at site.

Supply, fixing testing and commissioning of Plug and socket enclosure i) metal clad plug 20A -1 No ,ii)Metal clad socket 20A -1 No, iii)20A DP RCCB-1 No with internal wiring complete in an approved manner and as directed by the Engineer-in-Charge at site.

Supply at site, erection, testing & commissioning of Horizontal flush/ wall mounting type , powder coated sheet steel , SPN MCB 12 Way distribution board phosphatised and powder coated, double door with supply and fixing of 1 Nos. of 40 amps DP RCBO with 10 KA short circuit capacity and 30mA sensitivity, as incoming control with 6 Nos. of 6-32 amps SP MCBs with 10 KA breaking capacity as outgoing control, including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL &Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts &nuts with flat and spring washers &lugs invariably. 3.Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Horizontal flush/ wall mounting type , powder coated sheet steel , SPN MCB 12 Way distribution board phosphatised and powder coated, double door with supply and fixing of 1 Nos. of 40 amps DP RCBO with 10 KA short circuit capacity and 30mA sensitivity, as incoming control with 8 Nos. of 6-32 amps SP MCBs with 10 KA 49 breaking capacity as outgoing control, including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL &Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts &nuts with flat and spring washers &lugs invariably. 3.Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Horizontal flush/ wall mounting type , powder coated sheet steel , SPN MCB 6 Way (8+18) distribution board phosphatised and powder coated, double door with supply and fixing of 1 Nos. of 40 amps TPN RCBO with 10 KA short circuit capacity and 30mA sensitivity, as incoming control with 18 Nos. of 6-32 amps SP MCBs with 50 10 KA breaking capacity as outgoing control, including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL &Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts &nuts with flat and spring washers &lugs invariably. 3.Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Horizontal flush/ wall mounting type , powder coated sheet steel , SPN MCB 16 Way distribution board phosphatised and powder coated, double door with supply and fixing of 1 Nos. of 63 amps DP RCBO with 10 KA short circuit capacity and 30mA sensitivity, as incoming control with 12 Nos. of 6-32 amps SP MCBs with 10 KA 51 breaking capacity as outgoing control, including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL &Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts &nuts with flat and spring washers &lugs invariably. 3.Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Vertical flush/ wall mounting type , powder coated sheet steel , TPN MCB 8 Way distribution board phosphatised and powder coated, Double door with supply and fixing of 1 Nos. of 160 amps FP MCCB Adjustable thermal & Fixed magnetic with 36 KA breaking capacity , as incoming control with (i)6 Nos. of 40 amps DP MCBs (ii)5 Nos of 63 amps DP MCB with all 10 KA breaking capacity as outgoing control, including internal 52 wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL & Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts & nuts with flat and spring washers &lugs invariably. 3. Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Vertical flush/ wall mounting type 53 , powder coated sheet steel , TPN MCB 8 Way distribution board phosphatised and powder coated, Double door with supply and fixing of 1 Nos. of 160 amps FP MCCB Adjustable thermal & Fixed magnetic with 36 KA breaking capacity , as incoming control with (i)3 Nos. of 40 amps DP MCBs (ii)2 Nos of 63 amps DP MCB (iii)2 Nos of 40A FP MCB (iv) 1 No of 63A FP MCB with all 10 KA breaking capacity as outgoing control, including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note: 1.Bi-metallic washers must be provided for AL & Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts & nuts with flat and spring washers &lugs invariably. 3. Board shall be fixed in concealed manner.

Supply at site, erection, testing & commissioning of Vertical flush/ wall mounting type , powder coated sheet steel , 12 way MCCB distribution board phosphatised and powder coated, 400A "LS" Frame Double door with supply and fixing of 1 Nos. of 400 amps FP MCCB Adjustable thermal & Fixed magnetic with 36 KA breaking capacity , as incoming control with 1 Nos. of 250 amps FP MCCBs Fixed thermal & Fixed magnetic with 25 KA breaking capacity and 5 nos of 160A FP MCCB Fixed thermal & Fixed magnetic with 25 KA breaking capacity,1 No of 125A FP MCCB Fixed thermal & Fixed magnetic with 25 KA breaking capacity, 5 No of 63A FP MCCB Fixed thermal & Fixed magnetic with 25 KA breaking capacity as outgoing control, with Cable Alley Incoming 400A and 54 outgoing 4P GF 12 way and provision of Ammeter-1 no,Voltmeter-1 No analog with selector switch and indicators for double door,3 Phase LED Voltmeter Cl 1-1 no,MFM 4405 LED meter Cl 0.5 with RS485 including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note:1.Bi-metallic washers must be provided for AL & Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts & nuts with flat and spring washers &lugs invariably.3.Board shall be fixed in concealed manner. This Item Requires RITES Inspection prior to supply.

Supply at site, erection, testing & commissioning of Vertical flush/ wall mounting type , powder coated sheet steel , 8 way MCCB distribution board phosphatised and powder coated, 250A "AA" Frame Double door with supply and fixing of 1 Nos. of 250 amps FP MCCB Adjustable thermal & Fixed magnetic with 36 KA breaking capacity , as incoming control with 3 Nos. of 160 amps FP MCCBs Fixed thermal & Fixed magnetic with 25 KA breaking capacity and 1 nos of 125A FP MCCB Fixed thermal & Fixed magnetic with 25 KA breaking capacity,4 No of 63A FP MCCB Fixed thermal & Fixed magnetic with 25 KA breaking capacity as outgoing control, with Cable Alley Incoming 400A 55 and outgoing 4P GF 8 way and provision of Ammeter-1 no,Voltmeter-1 No analog with selector switch and indicators for double door,3 Phase LED Voltmeter Cl 1-1 no,MFM 4405 LED meter Cl 0.5 with RS485 including internal wiring by suitable wire and incoming cable termination using suitable terminal block with suitable cable gland, earthing / neutral din channel complete with all accessories duly making necessary opening on the wall and masonry work for controlling power/lighting/fan circuits in each building in an approved manner as directed by the section in charge at site. Note:1.Bi-metallic washers must be provided for AL & Cu joints and for others GI bolts, Nuts & washers must be used. 2.Cable termination shall be using GI bolts & nuts with flat and spring washers &lugs invariably.3.Board shall be fixed in concealed manner.

Supply, erection, testing and commissioning of 40W Aesthetically designed decorative Post top lantern hot dipped galvanized mild steel step pole with grey powder coated finish DECO POLE 3 Metre Top.76 mm dia,base cover (HSN Code:9405), Post top lantern similar to Havells 56 DECO POLE model no:RUBYPT40WLED757PSYMTOPC or its equivalent in IS certified make with terminal connectors, mounting accessories and with suitable foundation complete as per manufacturer recommendation in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.This Item requires RITES Inspection prior to supply.

Supply and installation of DLP U-PVC cable trunking system of size 195 x 50 mm, surface mounted type, conforming to IS 14927 (Part 1 & Part 2). The trunking shall be made of flame-retardant, self-extinguishing, UV-stabilized U-PVC, suitable for an operating temperature 57 range of -5°C to 60°C, non-corrosive and moisture-resistant.The work shall include complete fixing with GI plated screws, tight-fitting covers, and proper alignment of all accessories. Additional clamps/support arrangements shall be provided within 150 mm from both ends, at all bends, tees, and accessories, and near points carrying heavy cable loads, complete in an approved manner and as directed by the Engineer-in-Charge at site.This item includes RITES inspection prior to supply.

Supply and wiring including termination by 3 core 1.0 sqmm PVC insulated fire retardant low smoke (FRLS) flexible copper cable conforming to IS. No: 694,1100 V grade through the existing PVC pipe already laid/ casing-capping / on surface including dressing, clamping, termination with suitable lugs, complete in an approved manner and as directed by Engineer in charge at site.

Supply and wiring including termination by 4 core 6.0 sqmm PVC insulated fire 59 retardant low smoke (FRLS) flexible copper cable conforming to IS. No: 694,1100 V grade through the existing PVC pipe already laid/ casing-capping / on surface including dressing, clamping, termination with suitable lugs, complete in an approved manner and as directed by Engineer in charge at site.

Supply and fixing of clamps for BLDC Ceiling fans. The said clamps has to be fixed in the PF shelter with suitable fixing arrangements complete in an approved manner and as directed by site engineer incharge.

supply, fabrication, installation, and commissioning of a 19 mm diameter mild steel 61 (MS) tube an extension down rod for ceiling fan installation.The MS tube shall be of approved make and quality, straight, free from bends, dents, or corrosion, and suitable for ceiling fan mounting. The tube shall be cut to the required additional length as directed by the Engineer-in-Charge.

supply, laying,testing, and commissioning of Galvanized Iron (GI) earth strip of size 62 25 mm x 3 mm for earthing purposes.The GI earth strip shall be of approved make, conforming to relevant IS standards, with uniform thickness, smooth edges, and proper galvanization to prevent corrosion. The strip shall be laid in trenches, along walls, cable trays, or inside ducts complete in an approved manner and as directed by Engineer in charge at site.

Supply, erection, testing and commissioning of Mobile Charging Station, rack-type construction, suitable for charging multiple mobile devices simultaneously. The charging station shall be designed for operation on 240V AC, 50 Hz and shall be provided with 10 numbers of 6A modular switches and 6A modular socket outlets with indication lamp, all protected by 6A SP MCB 63 and 25A DP RCCB -1 Nos each, suitable for charging a minimum of 10 devices simultaneously. The enclosure shall be fabricated from mild steel sheet, duly powder coated, with adequate ventilation and proper earthing arrangement. Socket outlets and input plug shall conform to IS:1293 / 2005, and switches shall conform to IS:3854 / 1997. The item shall include all internal wiring, accessories, mounting hardware, testing and commissioning, complete in an approved manner and as directed by the Engineer-in-Charge at site.

Supply, installation, testing and commissioning of 40W Square type LED surface- mounted light fitting similar to Luker model no:LNPSRS40 with operating on 100-300V AC, 50 Hz supply with minimum 5 kV surge protection, body material Aluminium with polycarbonate diffuser , 64 suitable for outdoor application, , 120° beam angle, CRI >/= 80, and colour temperature 6000K as required, providing minimum IP40 ingress protection , with rated life of 50,000 burning hours, complete with mounting brackets, internal wiring complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply erection testing and commissioning of recessed and surface 40W 1x4 feet panel ceiling light with >100 Lumen/watt similar to Crompton model no:LCTLSNE-40-CDL(1x4) with 65 suitable wiring by 3 C x 1.0 sq.mm PVC insulated & sheathed round flexible copper cable complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

supply, installation testing and commissioning of a weatherproof polycarbonate cable 66 junction box of adequate size, rated IP65 or IP66 protection, complete with terminal blocks, gasketed cover, cable entry points, and all accessories suitable for outdoor and indoor use, providing dustproof and waterproof protection for cable terminations complete in an approved manner and as directed by Engineer in charge at site

Supply and fixing of heat shrinkable straight through cable jointing kit suitable for 67 4core LT cables of size 16 sq.mm to 95 sq.mm, including preparation of cable ends, jointing with connectors, application of heatshrink sleeves, sealing, insulation, testing and commissioning, complete in an approved manner and as directed by Engineer in charge at site

Supply and fixing of heat-shrinkable straight through cable jointing kit suitable for 4- 68 core LT cables of size 120 sq.mm to 150 sq.mm, complete with all insulating, sealing and protective components, including preparation of cable ends, jointing with suitable connectors/ferrules, application of heat-shrink sleeves using approved heating method, providing moisture-proof, dust- proof and mechanically strong joint, testing for continuity and insulation, complete in an approved manner and as directed by Engineer in charge at site

Supply, installation, testing and commissioning of BLDC wall mounting fan of 400 mm sweep,suitable for 220-240 V AC, 50 Hz supply, power consumption not exceeding 35 watts at maximum speed, minimum 5-speed electronic control, automatic oscillation, adjustable vertical tilt, air delivery not less than 70 CMM, maximum speed about 1200-1350 RPM, low noise operation, 69 aerodynamically designed 3-blade configuration made of ABS/aluminium, rust-resistant powder- coated guard, heavy-duty metal wall mounting bracket with locking arrangement, inverter compatible, provided with remote control / electronic regulator (as applicable), complete with all accessories, mounting hardware, wiring connections, making good the surface, testing and commissioning, of approved make and as directed by the Engineer-in-Charge.The fan shall be covered under a minimum 3 (three) years warranty from the date of commissioning, covering motor, electronic controller, and all associated components.

Erection, testing and commissioning of 500 LPD solar water heater includes providing RCC foundation/terrace mounting, fixing hot-dip galvanized structure with proper south orientation and tilt, installation of solar collectors and insulated storage tank, complete plumbing with CPVC/GI 70 pipes including inlet, outlet, air vent, drain, NRV and PRV with proper slope and supports; electrical works include 230 V single-phase supply through MCB and RCCB, FRLS copper wiring in conduit, thermostat, thermal cut-out, control switch and complete earthing; testing and commissioning include leakage and pressure testing, electrical insulation and earthing tests, system filling, air venting, performance check complete in an approved manner and as directed by Engineer in charge at site. Note:Necessary Solar water heater only will be supplied by Railways.

Supply, installation, testing and commissioning of 4 to 6 Watt LED Reading Light, suitable for indoor use, operating on 230 V AC, 50 Hz, with high efficiency LED source delivering uniform, glare-free illumination suitable for reading applications. The fixture shall have 71 polycarbonate body, integrated electronic LED driver, opal diffuser for soft light distribution, and CRI 80. Colour temperature shall be 3000K. The fitting shall be wall-mounted or surface-mounted (as applicable), complete with mounting accessories, internal wiring by 3 C x 1.0 Sqmm PVC insulated & sheathed round flexible copper cable complete in an approved manner and as directed by Engineer in charge at site. The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply and installation of Cable tray of Size 300mmx50mm height using50x50x6mm 72 angles of perforated cable trays with perforation not more than17.5% fabricated out of Mild steel conforming to IS 2062/1079 and Hot dip galvanized as perIS2629/4759(galvanizing not less than80 microns) in convenient sections, jointed with connectors complete as per the detailed specifications enclosed in the Annexure-I and as desired by the Engineer-in charge at site. Square

Design, manufacture, supply, erection, testing and commissioning of LED Name 73 board in three languages such as Tamil, English and Hindi with suitable fixtures made out of ALCO PANEL SHEET (ACP SHEET) complete as per specifications attached in Annexure-II.The complete board shall be erected at the desired location with suitable angle iron supporting structure including foundation complete in approved manner and as directed by Engineer in charge at site. The Board design shall get approved before manufacturing.

Supply erection testing and commissioning of 2 KVA/8640 VAH sine wave inverter with trolly and battery,Inverter govering specification:IS 13314,Technology;IGBT/PWM,Input:Single 74 Phase sine wave (120 to 260 V),Output;Single phase sine wave 240V,Inverter Efficiency:>/=87%,Overload of rated load:>/=10%,Degree of protection:IP 21,Total Harmonic Distortion </=5%,Type of battery:Tubular battery conforming to IS:13369,Backup time:180 minutes (minimum).Make Similar to:Luminious,Microtek,Exide or its Equivalent.Warranty:Inverter-2 years and Battery-5 years from the date of supply.

Supply,erection, testing andcommissioing of SMC box of size 140x140x95mm with 1 No of 6 A Strip connector, 16 A pocelain fuse carrier & Ceiling rose, including locking arrangement in an approved manner as directed by Engineer incharge at site.

3-Facade Lighting Arrangements

Supply, installation, testing, andcommissioning of exterior BISregistered 24W 24V DC RGBWLinear LED Wall Washer luminairefor facade lighting with extrudedaluminum housing, powder- coatedfinish, and Clear toughened glass.With all LEDs ON, minimumsystem lumen efficacy equal to orgreater than 62.9 lm/w. Theluminaire shall be capable ofproducing dynamic color-changinglight with 16 million colors as thelight fixture should beprogrammable using 8-bit controlDMX512 protocol / Ethernet basedcontrol. Luminaire should becomplete with a dedicated Lensmade up of UL/VDE approved PCfor each LED, offering beam angleof different types such as narrow,medium, wide or elliptical as perthe site requirement. The fixtureshould be erected with thenecessary required brackets andshould have constant lockinghinges for simple position controlfrom various angles withoutspecial tools. Fixture shall besuitable to operate at an ambienttemperature range of -30°C to50°C and complete luminaire shallbe IP66 and IK07 rated. LED Lifetime shall be at least L70@ 25C 76 @ 50000 burning hours at 25°C. LEDshould be ofNICHIA/OSRAM/SEOUL/PHILIPS/LUMILEDS/CREE/LEDNIUM/AVAGO make. The product shouldbe BIS approved with R numbermentioned on product label. To besupported with Product testreports - LM79, BIS Report andLEDs Test Reports. Luminaire shallbe conforming to BIS i.e. IS 10322(Part 5/Sec 5) and shall becomplete with all necessaryaccessories required for properworking of fixture includingweather proof connection cables,water proof connectors etc. asrequired. This includes crane charges if any for height work.(Warranty Period of 5 years). Alltest reports and technical datasheets to be submitted to thecompetent authority for approval.After installation, assembling andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be donein the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.This Item Requires RITES Inspection prior to supply.

Supply, installation, testing, andcommissioning of exterior BISregistered 36W 24V DC RGBWLinear LED Wall Washer luminairefor facade lighting with extrudedaluminum housing, powder- coatedfinish, and Clear toughened glass.With all LEDs ON, minimumsystem lumen efficacy equal to orgreater than 62.9 lm/w. Theluminaire shall be capable ofproducing dynamic color-changinglight with 16 million colors as thelight fixture should beprogrammable using 8-bit controlDMX512 protocol / Ethernet-basedcontrol. The luminaire should becomplete with a dedicated Lensmade up of UL/VDE approved PCfor each LED, offering beam angleof different types such as narrow,medium, wide, or elliptical as perthe site requirement. The fixtureshould be erected with thenecessary required brackets andshould have constant lockinghinges for simple position controlfrom various angles withoutspecial tools. The fixture shall besuitable to operate at an ambienttemperature range of - 30°C to50°C and the complete luminaireshall be IP66 and IK07 rated. LEDLife time shall be at least 77 L70@ 25C @ 50000 burning hours at25°C. LED should be ofNICHIA/OSRAM/SEOUL/PHILIPS/LUMILEDS/CREE/LEDNIUM/AVAGOmake. The product should be BISapproved with R numbermentioned on product label. To besupported with Product testreports - LM79, BIS Report andLEDs Test Reports. Luminaire shallbe conforming to BIS i.e. IS 10322(Part 5/Sec 5) and shall becomplete with all necessaryaccessories required for properworking of fixture includingweather proof connection cables,water proof connectors etc. asrequired. This includes cranecharges if any for height work.(Warranty Period of 5 years). Alltest reports and technical datasheets to be submitted to thecompetent authority for approval.After installation, assembling andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be donein the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.This Item Requires RITES Inspection prior to supply.

Supply, Erection, Testing andCommissioning of LED roundprojector type , 48W, RGBW, DC24V with IP 65 Protection, CastAluminium Double powdered paint,4mm safety glass IP 68Connectors, Luminaire efficacyrequired minimum guaranteed 50lumen/watt, CRI > 80, ProjectingDistance 30 Mtr, Control mode inDMX switchable dimmable /tunable, static Lighting. 9.5"Round Projector. The productshould be BIS approved To besupported with Product testreports and LEDs Test Reports.Luminaire shall be complete withall necessary accessories requiredfor proper 78 working of fixtureincluding weather proof connectioncables, water proof connectors etc.as required. This includes cranecharges if any for height work.(Warranty Period of 5 years). Alltest reports and technical datasheets to be submitted to thecompetent authority for approval.After installation, assembling andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be donein the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, installation, testing &commissioning of 200 watt DC 24VConstant Voltage driver to operatelighting systems having multipleLED modules connected in parallel,hence to make architecturallighting systems with a very slimform factor and seamlesslyintegrated into various 79 structures.The driver should becommissioned with all necessaryelectrical connections and havefollowing features: DC24VConstant Voltage Switch ModePower Supply, Waterproof IP65 orabove ingress protection,efficiency more than 85%.Operating temperature: -30 to+65 degree centigrade, THD lessthan 20% with necessaryconnections, Warranty : 5 Years,Electrical Safety Class: Class 1. (The work to be executed as perdirection of engineer in charge atsite. If any other items have beenomitted but required for efficientworking for facade lighting itwould be responsibility ofcontractor to supply and providesuch items. However the quotedrate shall be inclusive of thoseitems).The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, Installation, Testing, andCommissioning of exterior BISregistered 125W LED RGBW floodlighting luminaire for facadelighting with Die-cast aluminumhousing, powder-coated finish,minimum system lumen efficacyequal to or greater than 50lm/w.The luminaire shall be capable ofproducing dynamic color-changinglight with 16 million colors as thelight fixture should beprogrammable using 8-bit controlDMX512 protocol / Ethernet-basedcontrol. The luminaire should becomplete with a dedicated Lensmade up of UL/VDE approved PCfor each LED, offering beam anglesof different types such as narrow,medium, wide, or elliptical as perthe site requirement. Fixture withconstant locking hinges for simpleposition control from variousangles without special tools. Thefixture shall be suitable to operateat an ambient temperature rangeof -30°C to 50°C and the completeluminaire shall be IP66 and IK07rated. LED Lifetime shall be atleast L70B50 @ 50,000 burninghours at 50°C. LED should be 80 ofNICHIA/OSRAM/SEOUL/PHILIPSLUMILEDS/CREE/LEDNIUM/AVAGO make. DMXenabler circuit should be inside theLuminaire only. Luminaire shall becomplete with integrated BIS IP66/67 potted driver and capable ofoperating at line voltage from 90-305 Vac, 50Hz with power factor >0.9. The product should be BIS-approved with the R numbermentioned on the product label. Tobe supported with Product testreports - LM79, BIS Report, andLEDs Test Reports. Luminaire shallconform to BIS i.e. IS 10322 (Part5/Sec 5) and shall be completewith all necessary accessoriesrequired for the proper working ofthe fixture including weatherproofconnection cables, waterproofconnectors, etc. as required. Thisincludes crane charges if any forheight work.(Warranty Period of 5years). All test reports andtechnical data sheets are to besubmitted to the competentauthority for approval.Afterinstallation, assembling, andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be done in the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, Installation, Testing, andCommissioning of exterior BISregistered 90W LED RGBW floodlighting luminaire for facadelighting with Die-cast aluminumhousing, powder-coated finish,minimum system lumen efficacyequal to or greater than 50 lm/w.The luminaire shall be capable ofproducing dynamic color-changinglight with 16 million colors as thelight fixture should beprogrammable using 8-bit controlDMX512 protocol / Ethernet-basedcontrol. The luminaire should becomplete with a dedicated Lensmade up of UL/VDE approved PCfor each LED, offering beam anglesof different types such as narrow,medium, wide, or elliptical as perthe site requirement. Fixture withconstant locking hinges for simpleposition control from variousangles without special tools. Thefixture shall be suitable to operateat an ambient temperature rangeof -30°C to 50°C and the completeluminaire shall be IP66 and IK07rated. LED Lifetime shall be atleast L70B50 @ 50,000 burninghours at 50°C. LED should be 81 ofNICHIA/OSRAM/SEOUL/PHILIPSLUMILEDS/CREE/LEDNIUM/AVAGOmake. DMX enabler circuit shouldbe inside the Luminaire only.Luminaire shall be complete withintegrated BIS IP 66/67 potteddriver and capable of operating atline voltage from 90-305 Vac,50Hz with power factor > 0.9. Theproduct should be BIS-approvedwith the R number mentioned onthe product label. To be supportedwith Product test reports - LM79,BIS Report, and LEDs TestReports. Luminaire shall conformto BIS i.e. IS 10322 (Part 5/Sec 5)and shall be complete with allnecessary accessories required forthe proper working of the fixtureincluding weatherproof connectioncables, waterproof connectors, etc.as required. This includes cranecharges if any for height work.(Warranty Period of 5 years). Alltest reports and technical datasheets are to be submitted to thecompetent authority for approval.After installation, assembling, andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be donein the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, Installation, Testing, andCommissioning of exterior BISregistered 75W LED RGBW floodlighting luminaire for facadelighting with Die-cast aluminumhousing, powder-coated finish,minimum system lumen efficacyequal to or greater than 50lm/w.The luminaire shall be capable ofproducing dynamic color-changinglight with 16 million colors as thelight fixture should beprogrammable using 8-bit controlDMX512 protocol / Ethernet-basedcontrol. The luminaire should becomplete with a dedicated Lensmade up of UL/VDE approved PCfor each LED, offering beam anglesof different types such as narrow,medium, wide, or elliptical as perthe site requirement. Fixture with constant locking hinges for simpleposition control from variousangles without special tools. Thefixture shall be suitable to operateat an ambient temperature rangeof -30°C to 50°C and 82 the completeluminaire shall be IP66 and IK07rated. LED Lifetime shall be atleast L70B50 @ 50,000 burninghours at 50°C. LED should be ofNICHIA/OSRAM/SEOUL/PHILIPSLUMILEDS/CREE/LEDNIUM/AVAGOmake. DMX enabler circuit shouldbe inside the Luminaire only.Luminaire shall be complete withintegrated BIS IP 66/67 potteddriver and capable of operating atline voltage from 90-305 Vac,50Hz with power factor > 0.9. Theproduct should be BIS-approvedwith the R number mentioned onthe product label. To be supportedwith Product test reports - LM79,BIS Report, and LEDs TestReports. Luminaire shall conformto BIS i.e. IS 10322 (Part 5/Sec 5)and shall be complete with allnecessary accessories required forthe proper working of the fixtureincluding weatherproof connectioncables, waterproof connectors, etc.as required. This includes cranecharges if any for height work.(Warranty Period of 5 years). Alltest reports and technical datasheets are to be submitted to thecompetent authority for approval.After installation, assembling, andcommissioning contractor shouldensure that all parts of the lightare properly fixed and put it intorunning condition. The entire workshould be carried out as per theinstructions of Site Engineer.Testing of the fixtures to be donein the presence of Site Engineerfor a minimum period of 1 week.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.This Item Requires RITES Inspection prior to supply.

Supply, installation, testing &commissioning of Sky cove LEDRGB flexible strip light strip 5 mtrlong (1 roll) with 7.2 watt permeter with driver Model, LED stripshould have 30 nos LEDs permeter through out the length withthe silicon cover. The strip shouldhave IP 68 protection and shouldhave cover Glue Injected withpolyurethane. The nominal voltageshould be DC 24V, 83 workingtemperature range should bebetween -20 deg C to +50deg c.work should be completed withnecessary factory made weatherproof cable, lenses and externalpower and data supply[if any].suitable fixing arrangement asrequired complete in all respect asper direction of engineer incharge, warranty:-5 years,electrical safety class: class 1 (Thework to be executed as perdirection of engineer in charge atsite).The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply Erection testing andcommissioning of DMX signal cable/ shielded Cat. 6 or 84 better datacable shall be used for digitalcommunication networks. Size andquantity of cable shall be as persite requirement and as directedby SSE Incharge. Copper lugs,glands of proper size shall be usedfor connections.

Supply Erection testingcommissioning of male-Femalesets for connecting DMX cable 85 ofRGB fitting with 5-pin DMX XLRconnectors for lighting cables andEffects,Set includes one maleconnector and one femaleconnector, Gold pins for optimum signal transfer,Stranded TinnedCopper Conductors,PVC Jacket,Length - 6 inches.

Supply, Installation, Testing andCommissioning of DMX Splitterwith Input Voltage range : 100-240V 50-60Hz AC, PowerConsumption 4W/8W max.Housing is made of polycarbonatewith powder coated finishMounting, 19 inch rack mountable,Operation Temperature - 17°C to+55°C, 5 Output with 5pin XLRterminal sockets, IngressProtection Rating IP20. This unittakes the DMX Signal from DMXController & split the signal into 5DMX output per universe/10 DMXoutput for double rack versions.The output terminals of Splittersare optically isolated from theinput. 86 Splitters should be capableto amplify the DMX signal &allowing the data link to beextended by max. 300 m (1044ft.) using AWG 22 DMX cable or150 m (500 ft.) using AWG 24DMX cable or maximum 20-25fixture per output channel. To beprovided with IP enclosure ifinstalled in external environment.All test reports and technical datasheets to be submitted to thecompetent authority for approval.After installation, assembling andcommissioning contractor shouldensure that all parts of the DMXsplitter are properly fixed and putit into running condition. Theentire work should be carried outas per the instructions of SiteEngineer. Testing of the DMXsplitter to be done in the presenceof Site Engineer for a minimumperiod of 1 week. The make of thecable used shall be approved byRailways

Supply, Installation, Testing andCommissioning, of DMX Controllerfor the system including all otheraccessories required for therunning of the system Controllershould have Input Power 5-12V DCand Output Protocol DMX512 with4 universe, 2 universe should workin Stand Alone Mode and 2universe should work in live modewith laptop/ tablet / computer. Theuniverse should be expandablefrom 2 to 4 DMX512 universes. Itshould be compatible forProgrammability with PC, Mac,Tablet, Smartphone by using USB& Ethernet. DMX controller shouldhave network controllabilityfeature to control the sceneremotely through LAN andtriggered via UDP packets on port2430. It must have sufficientDMX512 RJ45 ports and sufficientRS-232 -pin serial ports. It musthave Connections Type C USB,XLR3, Ethernet, battery. Thereshould be provision for 87 MemorymicroSD card. Device should haveIntuitive backlit keyboard with 10presets and also have provision ofkeypad on device for changingscene manually from device.Device should be capable to workon Extended triggering possibilities(TCA) & also have Smart UpgradeTechnology (SUT). It is an IP 20unit and has an OperatingTemperature of 0°C to 50°C. OSRequirements for the controller isMac OS X 10.8-10.12, Windows7/8/10/11. Standards should beEC, EMC, ROHS. The controllershould have a variety of featuresincluding 2048 DMX channels,clock/calendar,iPhone/iPad/Android remotecontrol, Ethernet facilities, drycontact port triggering and multi-zone SD card memory. Networksynchronization of one area acrosshundreds of universes with thepossibility of 99 scenes across 5areas with auto clock triggering forsunrise and sunset and as per thefestivals for specific occasions.Device should be equipped withmeta; clamp to mount on wall.Facade lighting product and itsdriver should be compatible withDMX controller. To be providedwith IP 66 polycarbonateenclosure. (Warranty Period of 5years). All test reports andtechnical data sheets to besubmitted to the competentauthority for approval. Afterinstallation, assembling andcommissioning contractor shouldensure that all parts of the DMXcontroller are properly fixed andput it into running condition. Theentire work should be carried outas per the instructions of SiteEngineer. Testing of the DMXcontroller to be done in thepresence of Site Engineer for aminimum period of 1 week

Supply at site fixing testing andcommissioning of 5 Watts IP66Protected COB LED spike light tobe offered in Mono - Red (or)Green (or) Blue (or) Warm WhiteColour based on the site condition.Should have environmentalfriendly, compact, light weight,energy saving The Spike lightshould be Offered Warm WhiteColour. Multi purpose applicationlike column lighting, tree up- 88 lighting, statue accentuation etc.can be and toughened glassAdjustable mounting bracket withspike is provided for easy focus onthe object , constant currentelectronic driver having operatingvoltage range from 140-280 VoltAC; provided with high voltage,open and short circuit protectionLuminaire is wired with inbuiltdriver with 4.5kV surge protectionand wiring by 3 C x 1.0 sq.mmPVC insulated & sheathed roundflexible copper cable in anapproved manner as directedsection Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply at Site fixing testing andcommissioning of 9W landscapeBollard made up of Graphite greypowder coated GI Pipe housing,Sample to be submitted forapproval before supply, Theluminaire shall have opal acrylicdiffuser with IP65 protection isfixed in die-cast aluminium basefor pleasant light output LEDsmounted on die-cast aluminiumbase Luminaire is available 89 withcolour temperature: Warm White(WW): 3000K 250K Luminaire iswired with inbuilt driver with 4.5kVsurge protection device, Constantcurrent electronic driver havingoperating voltage range from 140-280 Volt AC; provided with highvoltage, open and short circuitprotection duly Installation ofabove bollard fixtures completewith suitable concrete foundationand wiring by 3 C x 1.0 sq.mmPVC insulated & sheathed roundflexible copper cable in anapproved manner as directedsection Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply Erection testing andcommissioning of LEDAesthetically designed, 90 decorativestrip light for decorative & covelighting applications 22W /5 Mtrswith necessary driver,3M adhesivetape on the back for fixing.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply at site fixing testing and commissioning of decorative wall mounting light 20 Watts made up of a body of die-cast aluminium alloy fitting similar to LUKER model no:LWL108(ANORA S2)suitable for indoor/outdoor use with high material resistant to discoloration working on 220 V AC Supply, Colour of LED: Cool white/Warm white, Luminaire is wired with in built 91 driver with 5kV surge protection, Constant current electronic driver having operating voltage range from 140-280 Volt AC; provided with high voltage, open and short circuit protection duly fixing in the wall and wiring by 3 C x 1.0sq.mm PVC insulated & sheathed round flexible copper cable in an approved manner as directed section Engineer in charge at site. The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply, installation, testing and commissioning of 2W to 4W LED Outdoor Wall / Step Light, suitable for exterior applications, waterproof IP65, complete with all accessories. The luminaire 92 shall be with die-cast aluminium housing, powder-coated finish, toughened glass / PC diffuser, integrated LED driver, and suitable for continuous outdoor operation. The fixture shall emit warm white / neutral white light (3000K / 4000K), with minimum CRI >80, operating voltage 220-240V AC, 50Hz with suitable wiring by 3 C x 1.0 sq.mm PVC insulated & sheathed round flexible copper cable complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply fixing testing and commissioning of Outdoor wall lights(Up/Down) of 3W to 6W 93 similar to KESSLEC model no KYIV or its equivalent including wiring complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply fixing testing and commissioning of track mounted spot light/wall washers 30W-min 2400 Lumens, aluminum housing with PC lens system lumen efficiency > 80 Lumen/watt 94 powered by Electronic LED driver with beam angle 24/36 degree,swing 0-355 degrees,tilt 0 to 90 degrees, CRI>80,operating temperature-20 to 45 degrees,colour temperature-3000K/4000K similar to philips cat ref no ST033TLED25 or its equivalent complete in an approved manner and as directed by Engineer in charge at site.The Warranty for the LED Light fitting will be 5 years and the payment condition will be followed as per Special condition-II para no:31.

Supply and laying of 4CX2.5sqmmXLPE insulated armoured coppercable suitable for Rated Voltage of1100V grade and conforming to IS7098 part I with amendmentnumber 1 2 and 3 95 reaffirmed 2005or latest and IS 8130 with latestamendments and with ISImarking. Cable shall be suppliedby the OEM or their authorizeddealer duly producing dealershipcertificate Cable shall be tested byCPRI ERDA NABL or any otherlaboratories recognized by theGovt. of India test certificate andOEM warranty certificate shall beproduced by the supplier alongwith the supply of the cable.

Supply and termination ofPolyamide cable glands & copperlugs suitable for terminating 4C x2.5 sqmm XLPE Insulatedarmoured copper cable. CableGlands - Cable shall be terminatedusing double compression typecable glands. Testing requirementsof Cable glands shall conform toBS:6121 and gland shall be ofrobust construction capable ofclamping cable and cable armour(for armoured cables) firmlywithout injury to insulation. Cableglands shall be made of heavyduty brass machine finished andnickel chrome plated. Thickness ofplating shall not be less 96 than 10micron. All washers and hardwareshall also be made of brass withnickel chrome plating Rubbercomponents shall be of neopreneor better synthetic material and of tested quality. Cable glands shallbe suitable for the sizes of cablesupplied/erected. Cables to beterminated - Unarmored HT powercables, Armoured and UnarmoredLT power cables, unarmoredControl cables and unarmoredScreened (instrumentation) cables2. Cable Lugs - Cable lugs forpower cables shall be tinnedcopper solderless crimping typesuitable for copper compactedconductor cables. Cable lugs andferrules for control cables shall betinned copper type. All powercable lugs shall be Single holetype. The cable lugs for controlcables andscreened/instrumentation cablesshall be pin type and shall beprovided with insulating sleeve.Cable lugs and ferrule shallconform to DIN standards.

Supply Erection testingcommissioning of 14 SWG GIEarth wire including binding with16 SWG GI wire complete Harddrawn GI, 14 SWG shall beerected at site as per requirementand 97 is should be bind with 16 SWGGI wire in proper manner, nutscheck nuts to be fixed fromunderside the bottom bracket withone set of nut on the top andother set of at the bottom to keepthe wire in position for supporting/terminating of the guard wire. Thework shall be done in an approvedmanner as per the site conditionsand instructions of field Engineer.

Supply and Installation of JunctionBoxes, Pipes & flexible conduit ofFRP JB (IP 65) Size: 139x119x70mm with stud type terminalsuitable for terminating 4c x 2.5sq.mm XLPE armoured cable,Thejunction box be 2.7 mm thick withelectrically insulated body shockproof, connector leads 98 and controlequipped with 1 nos.16 ampsrewireable fuse and its neccessarycutout. The box should be of frontdoor opening with rubber gasketto make it water tight. Thejunction box shall be vermin proofhaving rubber bushes at cableentry. The junction box shall bemounted on pole/ wall etc at theheight of 1.50 mtrs or as per sitecondition by providing MS clampsof suitable size. Color of junctionbox shall be got approved beforeerection. The junction box shall beerected in an approved manner asper the site condition andinstructions of field Engineer.

Supply and Installation of JunctionBoxes, Pipes & flexible conduit ofFRP JB (IP 65) 99 Size: 260x210x116mm with stud type terminalsuitable for terminating 4c x 2.5sq.mm armoured cable & housing1 driver,The junction box shouldbe 2.7 mm thick with electricallyinsulated body shock proof,connector leads and controlequipped with 1 nos.16 ampsrewireable fuse and its neccessarycutout. The box should be of frontdoor opening with rubber gasketto make it water tight. Thejunction box shall be vermin proofhaving rubber bushes at cableentry. The junction box shall bemounted on pole/ wall etc at theheight of 1.50 mtrs or as per sitecondition by providing MS clampsof suitable size. Color of junctionbox shall be got approved beforeerection. The junction box shall beerected in an approved manner as per the site condition andinstructions of field Engineer.

Supply of MS work ofmiscellaneous size and for cabletray etc including painting complete.

Fabrication fixing and erection ofMS work of miscellaneoussize,riveted, bolted or 101 welded inbuilt up sections including cutting,grinding and straightening,drilling, riveting, handling, hoistingand fixing in position etc. includingapplying a priming coat ofapproved steel primer etc. andduly painted with fine finish withcontractors steel and materials.The work shall be done as per thesite requirement in an approvedmanner and as per the instructionsof field supervisor.