752748 PROVN OF ADDN ALTN OF MD ACCN FOR OFFRS JCOs ORs AND MES KEY PERSONAL AT DANAPUR

Amount

SCHEDULE "A":

Item No 01:- Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thickness (below or above ground level) complete all as specified and directed.

Item No 2 :- Dismantling of floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

Item No 3 :- Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform. Chajjas etc.

Item No 04 : M&L for post construction Anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed.

Item No 05 :.M&L for treatment of soil using emuision for post construction Anti termite treatment along external wall below concrete or masonary apron using chemical emulsion at the rate of 2.25 litres per linear metre including drilling and plugging holes etc. in plinth protection or apron complete all as specified and directed.

Item No 06 : M&L for 10mm thick Light shade double charged vitrified ceramic tiles in floors, exceeding 0.36 sqm but not exceeting 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match compete all as sepcified & directed.

Item No 07 : M&L for 10mm thick Dark shade double charged vitrified ceramic tiles in floors, exceeding 0.36 sqm but not exceeting 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement to match compete all as sepcified & directed.

Item No 08 : M&L for non skid joint free ceramic coloured tiles of design as approved by GE 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

Item No 09 - M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm & not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement to match complete.

Item No 10 :- M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm & not exceeding 0.38 sqm in vertical surface such as skirtings, dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement complete.

Item No 11 :- M&L for 15 mm thick screed bed or bedding layer in CM 1:6 surface finished fair and even for laying floor finishes complete all as specified and directed.

Item No 12 :- M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed.

Item No 13 : M&L Machine cut Kota stone slab flooring 20-25m thick as in riser, steps & skirting, over cement mortar laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab incl rubbing, polishing & rounding to edges complete incl 10mm thick plaster in CM 1:4 complete all as specified and directed.

Item No 14 : M&L for glazed ceramic coloured tiles 450 x 300 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment (ii) Rendering shall be measured and paid separately under respective items.

Item No. 15 - M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of wall, finished even and fair complete all as specified and directed.

Item No. 16 :- Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Item No. 17 :- M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Item No. 18 :- M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Item No. 19 :- M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Item No. 20 :- M&L 75 mm thick PCC 1:3:6 type C1 using 20mm graded aggregate in plinth protection finished even and fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand (all by weight) complete.

Item No. 21 :- M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Item No. 22 :- M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Item No. 23 :- Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Item No. 24 :- M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed

Item No. 25 :- M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete. Note : Liquid WPC will be measured and paid separetely.

Item No. 26 :- M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth without using extra cement complete all as specified and directed .

Item No. 27 :- Supply only water proofing compound (liquid). ISI marked.

Item No. 28 :- Taking down chowkats or frames not exc 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Item No. 29 :- Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

Item No. 30 :- Taking down shutters of any description (without taking off shutters from the frames) n. exc 1 Sqm each and removing to store.

Item No. 31 :- Cutting holes in brick walls exc half brick but not exc one brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

Item No. 32 :- S&F Second class hard wood 35 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

Item No. 33 :- S&F Second class hard wood 35 mm thick factory made glazed and skeleton windows, ventilators shutters, open rebated and prepared to receive glass , gauze etc, divided into square,with plain, chamfered or rounded,mitered and rebated sash bars,any number, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed.

Item No. 34 :- S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Item No. 35 :- S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Item No. 36 :- S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

Item No. 37 :- S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed.

Item No. 38 :- S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

Item No. 39 :- S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of water tanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

Item No. 40 :- S&F pressed steel frames of size 105 mm x 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

Item No. 41 :- S&F pressed steel frames of size 125 mm x 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

Item No. 42 :- M&L for plain cement concrete 1:3:6 type C-0 (using 12.50 mm graded stone aggregate), as in back filling of pressed steel frames and similar work including necessary form work as required complete.

Item No. 43 :- S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trussed or rafters, cooler stands and similar small articles conforming to Fe 410-0 Fe 310-0

Item No. 44 :- S & F solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed

Item No. 45 :- S&F Factory made solid PVC Moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm plain colour PVC sheet on back face,with particle board core supplying and fixing in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

Item No. 46 :- S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

Item No. 47 :- M&L butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 for 100 mm long complete all as specified and directed.

Item No. 48 :- S&F butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type C-22 for 75 mm long complete all as specified and directed.

Item No. 49 :- S&F Butt hinges (ISI Marked), medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

Item No. 50 :- S&F Butt hinges (ISI Marked), medium weight, cold rolled mild steel 75 mm long complete all as specified and directed.

Item No. 51 :- S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

Item No. 52 :- S&F 150 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Item No. 53 :- S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

Item No. 54 :- S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

Item No. 55 :- S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

Item No. 56 :- S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

Item No. 57 :- S&F extruded aluminium alloy handles fabricated type anodised of 100 mm size complete all as specified and directed.

Item No. 58 :- S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

Item No. 59 :- S&F small fittings of 2nd class hard wood door, window stops and the like not exc 200 cucm each including MS butt hinges, medium weight, cold rolled 50mm long all as spd.

Item No. 60 :- S&F galvanized mild steel wire cloth 0.48 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Item No. 61 :-S&F in repair GI wire cloth 0.48 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

Item No. 62 :- Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty of fixed with beads complete all as specified and directed.

Item No. 63 :- S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Item No. 64 :- S&F figured glass 3 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

Item No. 65 :- Taking down old wooden/wood based particle board & S&F 18/19 mm thick high density PVC solid fibre board duly laminated 2mm thick prelaminated PVC sheet on front face (ISI mark) etc in kitchen cupboard etc.

Item No. 66 :- S&F 100 mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Item No. 67 :- S&F extruded brass handles, fabricated type, polished of 100 mm size complete all as specified and directed.

Item No. 68 :- S&F MS Peg set of six powder coated as approved by GE

Item No. 69 :- S&F in repair mild steel conduit curtain rod with PVC coating fancy type curtain rod 20 mm dia of any colour as approved complete.

Item No. 70 :- S&F mild steel Bracket with PVC coating fancy type for curtain rod 20 mm dia of any colour as approved complete.

Item No. 71 :- S&F powder coated anodised aluminium frame & shutters sliding or casement type for window/ventilator with one or more rebates including joining cleats. Glazing clips, rubber packing, aluminium snap beading, screw etc for fixing complete.

Item No. 72 :- Taking up or down steel tubing and connections including cleaning for refixing required for 15 mm bore of pipe complete all as specified and directed.

Item No. 73 :- Taking up or down steel tubing and connections including cleaning for refixing required for 20 mm bore of pipe complete all as specified and directed.

Item No. 74 :- Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Note :- (i) CPVC fittings with brass threading will be measured and paid separately under items No (ii) Cost of normal SDR CPVC fittings Like Bend, Tee, Elbow, UNIon etc shall inclusive under the quoted rate of pipe including.

Item No. 75 :- Supply & laying of CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete.

Note :- (i) CPVC fittings with brass threading will be measured and paid separately under items No (ii) Cost of normal SDR CPVC fittings Like Bend, Tee, Elbow, UNIon etc shall inclusive under the quoted rate of pipe including.

Item No. 76 :- S&F CPVC 20mm Outer dia Brass Elbow complete.

Item No. 77 :- S&F CPVC 20 mm Outer dia Brass Elbow (3/4 x 1/2) complete.

Item No. 78 :- S&F CPVC 20 mm Outer dia Brass Tee complete.

Item No. 79 :- S&F CPVC 20 mm Outer dia male Brass threaded Adoptor )3/4 x 1/2) (MTA/MBTA) complete.

Item No. 80 :- S&F CPVC 25 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

Item No. 81 :- S&F CPVC 20 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

Item No. 82 :- S&F CPVC 25 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

Item No. 83 :- S&F CPVC 20 mm Outer dia Brass Tank Adoptor complete.

Item No. 84 :- S&F CPVC 25 mm Outer dia Brass Tank Adoptor complete.

Item No. 85 :- S&F CPVC 20 mm Outer dia Brass Union complete.

Item No. 86 :- S&F CPVC 25 mm Outer dia Brass Union complete.

Item No. 87 :- M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves,lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good in brick walls, cutting not exceeding 10 cm girth complete all as specified and directed.

Item No. 88 :- S&F in repair chromium plated single lever basin mixer single lever without popup waste system with 450 mm long braided hoses complete.

Item No. 89 :- S&F in repair chromium plated single lever wall sixer 3-in-1 system with provision of both hand shower cimplete with 115mm long bend pipe, connecting legs and flange complete.

Item No. 90 :- S&F chromium plated single lever wall mixer with connecting legs and wall flange complete.

Item No. 91 :- S&F in repair vitrecous china WHB size 550x400 mm white flat back including PVC waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete.

Item No. 92 :- S&F vitreous pedestal china for WHB as per suilable for WHB size 550x400 mm complete..

Item No. 93 :- S&F in epairs white vitreous china wash down water closet pan pedestal pattern (white) excluding bolts, flushing cistern and flush pipe complete all as specified and as directed.

Item No. 94 :- S&F in repair vitreous china squating pan 'Orissa' pattern WC size 580x440 mm white with integral foot rest and trap and including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor all as spd.

Item No. 95 :- S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

Item No. 96 :- S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete.

Item No. 97 :- S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

Item No. 98 :- S&F cabinet mirror, box type of size 19" x 21" of colour as approved fixed to wall compete.

Item No. 100 :- S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

Item No. 101 :- S&F for repair 15mm bore pillar taps cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly-nuts screwed for iron pipe & fixed complete.

Item No. 102 :- S&F for repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

Item No. 103 :- S&F for repair aluminium anodised tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

Item No. 104 :- S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

Item No. 105 :- S&F in repair CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

Item No. 106 :- S&F in repair of stainless steel soap dish, of standard size and shape complete.

Item No. 107 :- S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever brackets and connecting union to pipe overall size 915 x 460 mm, bowl size 410 x 30 x 160 mm complete.

Item No. 108 :- S&F in repair sinks without drainge board made of stainless steel 1mm thick kitchen or laboratory with plugs, washes and waste pipe incl bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete.

Item No. 109 :- S&F repair 0.63 mm thick kitchen plate rack made of astainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified.

Item No. 110 :- S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

Item No. 111 :- S&F in repair plastic water closet seat cover, Cream / white cotour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC.

Item No. 112 :- S&F PVC (SWR) 'P' trap for 110 mm dia etc complete.

Item No. 113 :- S&F in repair chromium plated toilet paper holder with flap complete.

Item No. 114 :- M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall,beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Item No. 115 :- M&L for 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Item No. 116 :- M&L for machine cut cudappah stone slab 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Item No. 117 :- S&F Mild Steel TMT bar 8 mm dia & Over, cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Item No. 118 :- Taking down AC/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning ort joints of 100 mm dia pipe.

Item No. 119 :- S&F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

Item No. 120 :- S&F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed.

Item No. 121 :- M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

Item No. 122 :- S&F PVC (SWR) pipes 50 mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

Item No. 123 :- S&F stack clamps made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nut and securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed.

Item No. 124 :- S&F PVC (SWR) bends any radius of 110 mm bore with out access door complete all as specified and directed.

Item No. 125 :- S&F PVC (SWR) bends any radius of 110 mm bore with access door complete all as specified and directed.

Item No. 126 :- S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

Item No. 127 :- S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

Item No. 128 :- S&F PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified & directed.

Item No. 129 :- S&F PVC (SWR) branch pieces, single (equal or un equal), ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door

Item No. 130 :- S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Item No. 131 :- M&L PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

Item No. 132 :- Dismantling water tanks of any description, capacity exc 250 and not exc 500 litres and removing from site complete all as specified and directed.

Item No. 133 :- Dismantling water tanks of any description, capacity exc 500 and not exc 1000 litres and removing from site complete all as specified and directed.

Item No. 134 :- S & F rotational moulded polyethylene water storage tank tripple layer (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed

Item No. 135 :- S & F rotational moulded polyethylene water storage tank tripple layer(cylindrical vertical with closed top)1000 litre capacity hoisted and fixed in position complete all as specified and directed

Item No. 136 :- S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

Item No. 137 :- S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete.

Item No. 138 :- M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Item No. 139 :- M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Item No. 140 :- Removing old paint by paint removers or burning off by blow lamps and cleaning with scrapers, any number of coats, any width or girth complete all as specified and directed.

Item No. 141 :- M&L for preparation of old surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

Item No. 142 :- M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified.

Item No. 143 :- M&L for apply 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified.

Item No. 144 :- M&L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete all as specified.

Item No. 145 :- M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including. Rubbing with sand paper complete all as specified.

Item No. 146 :- M&L for applying 2mm thick Birla /JK Putty in two layers on old ceiling surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth rubbing with sand paper complete.

Item No. 147 :- M&L for preparation of newly plastered surfaces of ceiling and applying 2mm thick wall care putty including preparation of new surface complete.

Item No. 148 :- M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

Item No. 149 :- M&L for preparation of old decorated surfaces of walls by washing, rubbing down and scrapping of distemper surfaces and applying one coat of Oil Bound Distemper of any light shade complete all as specified and directed.

Item No. 150 :- M&L for preparation of old decorated plastered or unplastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash complete all as specified and directed.

Item No. 151 :- preparation of old surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Item No. 152 :- M&L preparation of new plastered or unplstered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

Item No. 153 :- M&L Preparing old painted surfaces of walls, chajjas etc by washing rubbing down and stopping and applying two coat of cement base paint white or tinted complete all as specified as directed.

Item No. 154 :- Preparing surface of sunken slab and applying 15 mm thick cement plaster 1:4 cement sand mortar with integral water proofing compound both on floor and wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating polymer modified cementitious coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturer's instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder complete all as specified. (IWPC will be paid separately)

Item No. 155 :- M&L water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete all as specified and directed.

(a) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg /Sqm

(b) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces.

(c) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane weight not less than 3kg/Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

(d) Applying two coats of bituminous aluminium paint including preparation

Item No. 156 :- M&L for PCC 1:2:4 type B0 (using 12.50 mm graded stone aggregate) in roof padding/kerbs/sunken slab etc complete all as spd and directed.

Item No. 157 :- M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick or concrete surface of roof finished even and fair complete all as specified and directed.

Item No. 158 :- M&L Hydrulically pressed burnt clay tile plain of size 200x200x19/20mm machine made laid over roof & including cement mortar screed 15mm thick in CM 1:6 mixed with water proofing compound and jointed, pointed in CM 1:3 mixed with 5% crude oil by weight of cement.

ELECTRIFICATION

Item No. 159 :- Taking down copper / aluminium point wiring (light, fan, bell, socket or power) complette including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc.

Item No. 160 :- Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN / Main Switch including old unserviceable MCCBs /MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site.

Item No. 161 :- Taking down carefully copper/aluminium Sub main wiring of any size from surface /concealed /existing conduit of any height and removing materials from site and making good disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Item No. 162 :- M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed heavy duty non metallic PVC rigid conduit white/ivory colour of size 20/25 mm ISI marked inclusive of tees, bend, elbows etc upto and including sunk in Anodized pressed steel box 1.6 mm thick 60 mm deep for housing switch socket etc. with white laminated 3 mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLS cable as earth wite to common earth dolly for connection to ceiling rose to earth terminal incl cutting, chasses and markig good disturbed surface to match with existing finish with plaster for complete all as specified and directed by Engr-in-charge

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 amps

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch one the same board.

(e) One 3 pin 5 Amps switch outlet point controlled by one switch on independent board.

(f) One bell point controlled by one, bell switch 5 Amps

Item No. 163 :- Description all as per item No 162 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLS PVC insulated unshealthed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLS PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

Item No. 164 :- M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (Nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following:-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 pin 5 Amps switch outlet point controlled by one switch on independent board.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One light point controlled by one, two way switch 5 amps

(f) One bell point controlled by one, bell switch 5 Amps

Item No. 165 :- Description all as per item No 162 here in before but using 2.5 sqmm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly

Item No. 166 :- Description all as per item No 162 here in before but using 4.0 sqmm single core copper conductor cable of multistranded FRLS PVC insulated unsheathed 1100 volts grade for 5/15 amps amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLS wire as earth continuity conductor along with wiring and connecting to the common earth dolly for AC point.

Item No. 167 :- S&F Switch Piano type single pole 5 amp, 230 Volts complete all as specified and diected at site.

Item No. 168 :- S & F switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed.

Item No. 169 :- S&F switch Piano type single pole 15 amp, 230 Volts complete all as specified and directed at site.

Item No. 170 :- S & F switch bell push piano type 5 Amp, 230 Volts complete all as specified and directed.

Item No. 171 :- S & F socket outlet 2 in 1, 5 pin 5 Amps 230 Volts complete all as specified and directed.

Item No. 172 :- S & F socket outlet 2-in-1, 6 pin 5 Amps & 15 Amps, 230 Volts complete all as specified and directed

Item No. 173 :- S&F ceiling rose, surface Bakelite with 3 terminals. ISI marked for batten fitting complete all as specified

Item No. 174 :- S & F stepped type electronic fan regulator flush Type complete all as specified and directed at site.

Item No. 175 :- S & F Modular Switch piano fush type, single pole, one way and 5/6 Amp single module complete all as specified.

Item No. 176 :- S & F Modular Switch piano fush type, single pole, one way and 15/16 Amp single module complete all as specified.

Item No. 177 :- S & F Modular Switch piano fush type, single pole, two way and 5/6 Amp single module complete all as specified.

Item No. 178 :- S & F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No. 179 :- S & F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

Item No. 180 :- S & F modular step type fan regulator 120 watt 2 module suitable for 230 Volt 50 Hz AC supply complete all as specified and directed

Item No. 181:- S&F Bell push modular 6 Amps single module complete all as specified.

Item No. 182 :- S & F lamp holder, PVC / Polycarbonate type with back plate suitable for batten / slanting fittings complete all as specified and directed.

Item No. 183 :- S & F Bell Electric Ding dong type suitable for operation on 230 volt 50 Hz A C supply complete all as specified and directed.

Item No. 184 :- M&L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heacy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable, one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 185 :- M&L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two run of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable, two runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit

Item No. 186 :- S&F sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 amps reted bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

Item No. 187 :- S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provis on for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

Item No. 188 :- S & F MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 189 :- S & F MCB Single pole and neutral reted capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 190 :- S & F MCB Single pole reted capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 191 :- S & F metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and directed.

Item No. 192:- S & F Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp, in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed.

Item No. 193 :- S & F Decorative wall mounted luminaire made our of polycarbonate with sunbreakable globe suitable for LED bulb and provosio of LED bulb 10 Watts complete all as specified and directed. Ake Havells Cat No LHDLO6160099 or its equvalent in philips, Bajaj.

Item No. 194 :- S & F LED 10 Watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Cat Part No BCLSB 10 NW or its equivallent model in Wipro, Philips.

Item No. 195 :- S & F Energy saving new generation 10 Watts LED bulk head fitting IP-65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 form ceiling rose to fitting including LED bulb complete all as directed. Make :- Bajaj Cat NO.BIBWP 10W LED or its equivalent in PHILips, Wipro.

Item No. 196:- S & F wall mounted LED tube light fitting 20 watts batten for surface molnted, anodized extrded aluminium housing, high transmissitivity diffuser, high lumen etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make:- Baja Cat Part No BCLAB 20 W, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in philips Havells.

Item No. 197 :- S & F for Energy saving new generation environmental friendly friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer-in-charge. Make :- Bajaj Cat Part No BRLEP 25W LED WH (Edge plus series) or its equivalent in Philips, wipro.

Item No. 198 :- Taking down ceiling fan/exhaust fan of any sweep, keeping with safe custod and refixing the same with replacement of UNSV 3 core PVC insulated PVC sheased 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and directed.

Item No. 199 :- S & F Energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 Cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan complete all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Item No. 200 :- Supply, installation, commissioning and testing LT wall mounting Panel Board of minimum size 1.00 m (height) x 1.00 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four nos Three phase meter and MCB TPN and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 Sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge.

OUTGOING (a) MCB, Tripple pole & neutral, 40 amps, 415 volts, 'C' curve, 10 KA all complete as specified and as directed - 4 Nos (Officers Accn) (b) MCB, single pole & neutral, 10 amps, 240 volts, 'C' curve, 10 KA all complete as specified and as directed - 01 Nos (Stair case lighting) (c) Single Phase Electronic Energy Meter accuracy Class 1.0, 240V, with in home display 5-30 A, 3 nos self locking meter seal, LCD diplay with option port, anti temper features, LCD test, serial no, Date, RTC, Cumulative Kwh, Last bill Kwh, Instanteous Load, Last bill MD, In stantaneous KW Volts, PF, HZ, MD, total Tamper Count Self billing Code, Battery backup in absence of power for display active energy kwh, including all incoming and out going connections. = 01 Nos (Make-L&T, Cat No:WM101BC5DDH/Secure) (d) Supply and fixing of Three Phase Electronic Energy Meter accuracy Class 1.0, 240V, with in-home display 10-60A, 3 Nos self locking meter seal, LCD display ooptical port, anti temper features, LCD test, serial no, Date, RTC, Cumulative Kwh, Last bill Kwh, instanteous Load, Last bill MD, Instantaneous KW, Volts, PF, HZ, MD, total Tamper Count, Self Billing Code, Battery backup in absence of power for display active energy kwh, including all incoming and out going connections =04 Nos (Make-L&T, Cat No: WR301BC7D10 / Secure)

Item No. 201 :- Supply, installation, commissioning and testing LT wall mounting Panel Board of minimum size 1.00 m (height) x 1.00 m (breadth) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four nos single phase meter and MCB and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves MCCB input and MCCB/MCB output of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfces suitable for 3 phase 4 wire system 315/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by EIC.

Item No. 202 :- M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically (earth pit not less than 2.25 m deep below ground level, with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part -I including excavation and earthwork in any type of soil/strata and testing on completion (Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.)

SCHEDULE "A" (Schedule of credit) Schedule of Credit Rs 733615.00 (Minus) inserted by the MES (Note : Credit amount shall be deducted manually to arrive net bid amount)

L G BUILDERS

NALIN RANJAN