Construction of Solarized cold chain room at Block Medical HQ Khaltsi. Under NHM.

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Dumping stone including cost of stones. On Horizontal

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse and : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone laid dry in foundation, plinth & walls: Laid with bond stone

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more..

Providing & fixing upto floor five level precast sundried mud bricks in mud mortar using approved quality mud with carriage of material complete.

Centering and shuttering including strutting, propping etc. and removal of form for: a) Foundations, footings, bases of columns, etc. for mass concrete

b) Suspended floors, roofs, landings, balconies and access platform

c) Lintels, beams, plinth beams, girders, bressumers and cantilevers

d) Columns, Pillars, Piers, Abutments, Posts and Struts

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate.

Providing and fixing 12mm thick prelaminated flooring of approved brand as per the direction of Engineer incharge, complete Job AC-4 Including carriage complete Job

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class Kail wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frames of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35m thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; Local willow wood

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

French spirit polishing : Two or more coats on new works including a coat of wood filler

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windowscomprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm),made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wallthickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing double glass unit DGU comprising of 6 mm thick glass on either with 12 mm thick insert gas gapping. The DGU shall be process from reputed glass processor.

Providing and fixing 3 layer PP-R (Polypropylene Random copolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clampsat 1.00m spacing. This includes testing of joints complete as per direction of Engineer in Charge. (Internal work exposed on wall) PN - 16 Pipe, 25mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Polypropylene Random copolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clampsat 1.00m spacing. This includes testing of joints complete as per direction of Engineer in Charge. (Internal work exposed on wall) PN - 16 Pipe, 32mm OD (SDR-7.4)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing insullation for of material for the insullation of water storage tank by way of using Nitrale sheet 25mm thick,tapping with cello tape, rockwool 6" per side, wire mesh, polythene, and aluminium sheet 26 gauge cladding with dia .(Complete Job)

Providing and fixing white vitreous china pedestal type water closet (European type WC pan) with seat and lid 10 lit. Low level white PVC flushing controlled device handle lever ) conforming to IS 7231 with all fittings and fixtures, complete including cutting and making good the walls and floor wherever required: WC pan with ISI marked white solid plastic sear and lid of approved brand

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

Providing and fixing PVC plain bend of required degree 100 mm dia

Providing and fixing C.P.brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15mm nominal bore.

Providing and fixing FT elbow of approved make PVC 75MM

Providing and fixing PTMT Waste Coupling for washbasin and sink, of approved quality and colour. Waste coupling 3.1 mm of 79mm length and 62mm breadth weighing not less than 45gms

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) WhiteVitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing of PVC waste pipe of required did including bend, tee door bend, L bend trap jointed with addisive material ISI marked like prince, vector or equivalent brand all complete Job 100 mm dia bore

Providing and fixing of PVC waste pipe of required did including bend, tee door bend, L bend trap jointed with addisive material ISI marked like prince, vector or equivalent brand all complete Job 75 mm dia bore

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102mm , height of 75 mm with concealed fitting arrangements weighing not less than 106 gms.

Providinf and fixing Health Faucet with 8mm dia 1m long PVC tube and wall Hook an approve quality.

Providing and fixing toilet paper holder : Vitreous china

Providing and fixing of geyser of required capacity fixing with all fixture Complete Job. 25Ltr

Providing and fixing of PVC SS connection pipe for geyser and wash basin

Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing CP Jalli of approved material

Providing and fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape for (Inner Wall) fitting Complete Job Including carriage PPR 25mm

Providing and fixing of heat tape on 33watt on PPR pipes approved brand (denforse / chromalox) or equivalent make as approved by Engineer Incharge Complete Job

Providing and fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape, rockwool 6 inch per side, wire mesh, polythene, tapping with cello tape and aliminium sheet 26 Gauge cladding with dia. Complete Job Including carriage 19mm thick , 50mm dia OD PPR 32mm

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 18 mm thick

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality..5 mm thick 1.0 mm thick

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc.complete as per directions of Engineer- in-charge.

Providing and fixing Solar water geyser of standard quality 100Ltr Including cost and carriage upto site of work Complete Job

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar with bhusha @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 2 cow-dung) and covered with machine moulded tile bricks, grouted with cement mortar 1:3 ( 1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat. With machine moulded common burnt clay F.P.S. (non modular) brick tiles of class designation 12.5, conforming to IS 2691

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, includingmcleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -11

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Carriage of material from source to site of work by Mechnical Transport including loading unloading and stacking. a) Cement and steel an avg lead 01Km

b) Sand an avg lead 20 Km

c) Stone aggregate an avg lead 20 Km

d) Stone an avg lead 15km

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.10.1 Group A

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 Sq.mm + 1 x 2.5 Sq.mm earth wire

2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire

2 x 10 Sqmm + 1 x 6 Sq.mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 1 x 1.5 sq. mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

3 pin 5/6 A socket outlet

15/16 A switch

6 pin 15/16 A socket outlet

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 230 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without CB/RCCB/Isolator) 8 way , Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required 100 A,30KA,FPMCCB

change over switch 63Amp

Fabrication, supplying , installation testing and commissioning of following pannel made out of 2 mm thick M.S sheet, wall mounted, vermin & dust proof outdoor type with lockable type hinged doors duly painted with provision for fixing of 1No including supply and fixing 2 set of Aluninium Bus bar, and strip for housing MCB's 12 Nos, MF Digital Meter and other allied accessories as required. ( Make as per annexure)

Supplying and fixing of following rating 240/415 Volts ''C''series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commisioning. ( above to 32 Amp) SPN 63 Amp

20 watt LED tube light fitting LL20-221-XXX-65 NE3 of wipro or equivalent make and mnodel Philips/ Crompton Greaves.

Supplying and fixing of Angle/Baten Holder with 9 watt LED Lamp polycarbonate including making complete connections etc as required (Make as per annexure enclosed)

Supplying and fixing of concealed light of required watt 10/18 watt

Exhaust fan 300 mm size (Heavy duty) CG transair or equivalent approved make.