PROVISION OF CLASS ROOM WITH SEATING CAPACITY OF 45 RECTS/AGNIVEERS TOILET BLOCK 02 X WC 05 X URINAL AND 02 WASH BASIN NEAR KOTE AREA AT BRC ADDN/ALTERATION OF ALUMINUM PARTITION AND CERTAIN WORK AT STN HQ CELL AND ADDN/ALTERATION TO IRON GRILL GATE

Amount

Boring holes 5m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Excavation over area exc n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M& L ATT Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface of flooring complete all as specified and directed

M& L ATT Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed

M&L PCC 1:4:8 type-D2 (40mm graded stone aggregate) as in foundations, filling and mass concrete.sub base as in floors complete finished even & fair complete all as specified and directed.

M & L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L RCC type M-25 Design Mix using (20mm graded stone aggregate) as in beam, cantilevers, bressmummers, lintels over 1.5 m span, seismic bands etc complete all as specified and directed (Note :- Reinforcement shall be measured and paid separately under respective item)

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

Use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

Use & waste form work to sides and soffits of roof beams,beams and lintel or bressurements for rough finished , square, rectangular or polygonal surfaces of concrete

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floor, window cills, concrete railing, opening in concrete wall, sides of RCC slab, RCC / PCC bends in walls or floor / roof n. exc 20cm wide and not exc. 20 cm in rough finished surfaces of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including incl Screed bed or bedding layer of Cement Mortar (1:6), 15 mm thick for laying floor finishes, necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed. Note: (size of the stone slab not less than 22"x22")

M&L Machine cut Kota stone slab flooring 20-25mm thick as in skirting, over cement mortar laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete incl 10mm thick plaster in CM 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note:- Liquid WPC will be measured and paid separately.

M & L Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in CM 1:4 on concrete surfacves/ chajja/ ceiling, etc finished even and smooth without using extra cement complete all as specified and directed.

Supply only water proofing compound (liquid), ISI marked.

M & L for Non skid ceramic colour tiles (square / rectangular) joint free of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed (1:6) etc complete all as specified and directed.

M & L for 450x300 x7 mm thick glazed coloured ceramic tiles (Digital pattern) including highlighter colored as in dado/ skirting and vertical serfaces set&jointed in neat cement slurry and pointed in colored cement 0ver and incl 10 mm thick rendering cement mortar 1:4 to for laying etc of tiles complete all as specified and directed.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube, supplying and fixing in opening with and including fixing accessories as per specification and drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, (hold fast) Butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-O using 12.5 mm graded crushed stone aggregate complete all as specified.

S & F 35mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces , size of rail and stile as per IS:1003 (Part-I), Klin seasoned and chemically pressure treated all as per SSR complete all as directed.

S & F 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

M & L PCC 1:2:4 type B1 (20mm graded aggregates) as in bed blocks for hold fasts including necessary form works complete all as specified and directed.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks etc complete all as specified and directed.

S & F Steel ventilator with top hung shutter including, hinges, peg stay, complete all as spesified and directed

S&F aluminium alloy handles, cast type anodised 125 mm long complete all as specified and directed.

S&F, Aluminium hinges (ISI marked), medium weight of size 100 mm complete all as directed

S & F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F Aluminium handles, cast type, anodized 150 mm size complete ISI Marked complete all as specified and directed.

S & F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 250mm long complete all as specified and directed.

S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S & F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete (with glazing bars) dovetailed or welded complete all as specified and as directed.

~Ditto~ all as per item No 47.00 above but without glazing bars complete as specified and as directed.

S & F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165. complete all as specified and directed.

S&F mild steel conduit curtain rod with PVC coating fancy type drapery rod 20mm dia of any colour as approved and fixed with bracket complete all as specified and directed

M & L for two coats of Oil bound distemper over a coat of primer on newly plaster wall surfaces over and encluding 3 mm thick Birla / JK wall care Putty complete all as specified and directed.

M & L Preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L Preparing new plastered surfaces of ceiling and applying three coats of white wash etc complete all as specified and directed.

M & L preparation of new steel surfaces any description, not otherwise descrived, over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M & L preparing surfaces of new wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete.

S & F tubes medium grade galvanised iron with all fittings & fixed complete to walls & ceiling or laid in floors 20mm bore etc complete all as specified and directed.

S & F tubes medium grade galvanised iron with all fittings & fixed complete to walls & ceiling or laid in floors 25mm bore etc complete all as specified and directed.

S & F Vitreous China wash basin white flat back size 450x300 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia,PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450 mm length with brass CP nuts on both sides, complete all as specified and directed.

S&F 15mm bore angle cock, cast copper alloy CP, fency type high presure with capstan head handle, screwed both ends for iron pipe of for unions all as specified

S & F Gun-metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed.

S & F Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed.

S&F 600mmx450mmx6mm bevelled edge mirror mounted in 40mm wide PVC frame of approved size and colour on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete.

S&F repair vitreous china urinals bowl type flat back, size 465 x 355 x 265 mm, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe.

S&F CP urinal spreader for fixing with 15 mm bore pipe complete all as specified. Make : Hindustan/Parryware/Equivalent make

S&F in water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap front or back inlet incl provision of PCC bedding type B1, 1:2:4 ( 20 mm graded aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) complete.

S & F PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed.

S & F bib tap 15mm bore cast copper alloy chromium plated fancy type long body with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by the Engineer-in-Charge.

M&L Granite tiles 18-20mm thick machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing and incl 15mm thick screed bed CM 1:4 all as specified complete.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered hoisted and fixed in position all as specified in SSR Pt-I 500 Ltr capacity complete all as specified and directed.

S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball srewed for iron pipe and fixed (minium weight 20mm-210)gms. complete all as specifed and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints using solvent adhesives fixed to walls with brackets etc of 110mm dia complete all as specified and directed

-Ditto- all as per item No 72 above but 75mm bore including Rubber ring joint with solvent adhesives complete all as specified and directed.

S&F PVC (SWR) bends any radius provided of 75 mm dia complete all as specified and directed

S&F PVC (SWR) bends any radius provided of 110 mm dia complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia complete all as specified and directed

S&F 75/100 mm bore PVC (SWR) floor trap,plain with grating including jointing to waste pipe complete all as specified and directed

M&L for 15 mm thick screed bed in CM 1:4 with water proofing compound @ 200ml /50kg of cement as per manufacturer's instruction finished surface even and smooth with out using extra cement over roof slab etc complete all as specified. (Note : WPC will be measured & paid for separately).

M & L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidized bitumen based solvent primer @ 0.3 Kg / sqm. (iii) Applying evenly tack coat of industrial bitumen 85 / 25 grade @ 1.2 Kg / sqm. (iv) Laying unrolled over the bitumen coated surfaces polymeric water proofing membrane, hyperplas standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction. (v) Applying a coat of bituminous aluminium paint @ 100 gm / sqm over and including a coat of hot air blown grade bitumen of grade 85 / 25 @ 1.2 Kg / sqm duly sanded over polymeric membrane complete. Note:- The polymeric water proofing membrane shall be extended upto parapet walls and inserted in walls by cutting groove and making good with CM 1:3 complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) Vent cowl complete all as specified and directed

S&F Factory made soild panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, all as per specification and drawing..

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

S & F for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, size of grid 605mm x 605mm complete all as specified and directed

S & F for hangers 6 mm dia GI (upto 1200mm length adjusting level fixed to roof/slabs by means of ceiling cleats made out of GI flat 40X3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed

M & L for 6 mm thick Non asbestos fibre cement building boards fixed or laid /inserted to timber /GI /Aluminium framework with screws complete all as specified and directed. Make- Armstrong, Hunterdouglas etc

S&F powder coating aluminum partition wall of aluminum section 80mm x 35mm x 2mm thick frame rectangular section and prelaminated particle board exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination in bottom panel and 5 mm thick frosted/tinted sheet glass in top panel with rubber lining and aluminum beading around length including necessary fixing arrangement for bottom and top member of aluminum frame in floor/PCC/Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre & necessary making good to surface as required at site all as specified and directed by Engineer-in-Charge (Note : Cost of PVC panel or prelaminated board and sheet glass shall deemed included in the unit rate of this item )

M&L double action floor spring for aluminium doors hydraulically regulated made up of minimum 1.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

M & L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting and also fastening confirming to Fe – 410 – W(Gde E - 250) quality 'B' complete all as specified and directed.

S&F for powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, indows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge

S&F in repair door closer hydraulically regulated, aluminium (extruded section) body, designation No.2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg etc complete all as specified & directed.

S&F in Repair brass Mortrise lock 2 lever any type complete all as specified and directed

S &F Rough cast, wired figured glass, 6.4mm thick and glazing with bead in squares exc 0.75 sqm eac complete all as spesified as directed

S& F Block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on both faces, complete all as specified

Cutting holes into or through brick/stone walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified & directed.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete.

M & L for light/fan Point wiring with PVC insulated and unsheathed electric cable of 1100 volts single core having FRLS multistranded copper conductor of 1.5 Sqmm nominal cross sectional area drawn in and including non metallic rigid PVC casing caping double lock system not less than 25mm base size with all fitting and fixing accessories and with 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor connected to earth dolly by providing suitable lugs including 1.6mm thick anodised pressed steel sunken box covered with 3mm thick hylum sheet for mounting switches. sockets etc complete for the following.

All as per item no 102 above but one bell point controlled by one bell Push

All as per item no 102 above but one 5 Amps socket out let point controlled by one switch on same board with other switches.

All as per item no 102 above but one 5 Amps socket out let point on independent board controlled by one switch.

All as per item no 102 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

Supply and fixing switch piano flush button single pole one way 5 amps, 240 Volts complete all as specified and directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, 240 Volts complete all as specified and directed.

Supply and fixing switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed.

Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 240 volts complete all as specified and directed.

Supply and fixing Ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

Supply and fixing for batten/angular fittings complete all as specified and directed.

Supply and fixing for electronic Fan regulator 450 watt step type complete all as specified and directed.

Supply and fixing double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed . Make: LEGRAND/ L&T/ SCHNEIDER/ABB

Supply and fixing with MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed . Make: LEGRAND/ L&T/ SCHNEIDER/ABB

Supply and fixing MCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete all as specified and directed .Make: LEGRAND/ L&T/ SCHNEIDER/ABB

Supply and fixing LED tube light batten box type including single tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder with single tube rod of 18/20 watt and all accessories internally pre wired and fixed to wall/ceiling incl fittings accessories and connecting up with twin core twisted flexible copper conductor cable upto ceiling rose/connetor suitable size all as specified. Make- Havells/Bajaj/Philips/Crompton/Surya.

Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with electronic driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and as directed. Make: Havells/ CG/ Bajaj/Surya.

Supply, fixing and testing of ceiling fan 1200 mm sweep, heavy duty, single phase, AC, 230 Volts, 50Hz, BEE 5 star rating, ISI marked complete with down rod, canopy, blades, BLDC motor etc and connecting up complete including complete connection from ceiling rose to fan including writing of MES Number with synthetic enamel paint complete all as specified and as directed. Make- Bajaj/Usha/ Crompton Greaves/Havell's.

Supply and fixing LED light fitting for bldg security lighting energy saving & environmental friendly long life versatile pressure die-cast housing with individual high power LED as light source and lens embedded PC cover of capacity 25 watt 240 volts AC 50 Hz , IK 07 and IP 66 protection suitable for 40/25 mm dia GI pipe bracket including three years on site warranty from manufacturer complete all as specified and directed. Make: Havells Cat No: ENDURAPEARLSL25WLED757SASYTOPCMP /Bajaj, / Crompton Greaves,

M & L for security wall light bracket made out of GI pipe light grade 25 mm dia 1.2 metre length bent to shape and reduced to required size at top upto 1.5 metre length by cutting, welding and well finishing including MS clamp of flat iron of size 40x6 suitable length 2 sets complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats of aluminium paints over a coat of red oxide primer including dismantling one complete all as specified and as directed.

Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core. Make: Havell's/Polycab/ KEI/MESCAB

M & L clean dry river sand in trenches/ducts for cushioning to cable, 8 cm in depth before laying the cable and 15 cm in depth after laying the cable complete all as specified. Note:- Punned thickness shall be measured and paid.

M & L for old size sub class ‘B’ bricks, laid in trenches as cable covers / protection complete all as specified and directed .

Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

Supply and fixing bell push single pole, 6 Amps, 240 Volts, flush type complete all as specified and directed.

Supply and fix LED Lamp 7/8 watt complete all as specified and directed.

Supply and fixing Bell, AC 240 Volts,single pole complete all as specified and directed.

Supply and fix exhaust fan, Plastic body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper wire upto ceiling rose complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Usha.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 2.5 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 2.5 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 2.5 sqmm cable,one run of 2.5 sqmm cable and one run of PVC conduit will be measured as one unit

HARINANDAN RAI SONS

M/S Priya Trading Agency

M/s Mukesh and company

M/S SAROJ KUMAR SINGH

jaglalchoudharyandsons

SINHA CONSTRUCTION

Vijay Bakshi and Son

MS BIJAY KUMAR AND SONS