Spl repair to bldg No T-11 (1-8) OR Md accn at Bana Singh Enclave and sewage lines, manholes and connected work at Tibri Mil Stn under GE Gurdaspur.

Amount

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and fair complete all as specified and directed

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:6. finishing even and smooth without using extra cement complete all as specified and directed

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. finishing even and smooth without using extra cement complete all as specified and directed

Dismantling of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed

M&L for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and directed

All as per Srl item No 07 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 05 shall be reused after necessary cleaning of mortar)

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement morter 1:4 , all as specified and directed.

M&L for complete removal of existing treatment of old decorated surfaces, plastered or un plastered of walls complete all as specified and directed

M&L for prepration of newly plastered/un plastered surfaces of wall and applying two coats of cement base paint of shade as approved complete all as specified and directed.

M&L applying two coats of oil bound distemper over a coat of primer including preparation on new plastered surfaces of wall complete all as specified and directed.

M&L for prepration of newly plastered surface and applying three coats of white wash as on ceiling.

M&L for preparation of old decorated surfaces plastered or un plastered of walls and applying one coat of cement base paint including cornices etc complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of walls, pillars and filling the all holes/patches with wall care putty where required to make surface smooth and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

M&L preparing old plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces plastered or un plastered of ceilng and applying one coat of white wash complete all as specified and directed.

Taking down Chowkats or frames from the opening of size not exceeding 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed

All as per Srl item No 18 above but size of opening exceeding 1.50 Sqm but not exceeding 4.00 Sqm

Taking down Shutters of any description of size exceeding 1.00 sqm and not exceeding 2.00 sqm each complete all as specified and directed

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete and refixing in the same opening after easing and adjustment all as specified and directed

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, painting shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, painting shall be measured and paid for separately

S&F pressed steel frames 1.25mm thick for door size of frame125 X 60mm with single or double rebates including necessary lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. ISI Marked.

S&F 25mm thick Flush shutters , solid core construction , with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S&F MS framed work as in chowkats, door or gates of angle or other section with gusset plates,rail, braces, etc. and similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F MS framed work as in stairs (framed) including stringers treads, landing , balusters, hand rails, including cleat bracket etc conforming to Fe 410-W Gde E-250 quality A complete.

M&L for repair to steps/landing of staircase with RCC 1:2:4 type B-0 using 12.50mm gradded aggregate including form work complete all as specified

S&F GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F in repairs GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

Hacking out old broken glass panes of any thickness description from wooden frame or stone concrete or steel frame or brick surrounds, glazed with putty or fixed with beads and prepared to receive new glass panes complete all as specified .

S&F sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading fixed nails/ oil putty complete all as specified and directed

All as per Srl item No 36 above but figured glass pin head type & glazing with oil putty

S&F 100mm long butt hinge, medium weight, cold rolled mild steel.

S&F 250mm long aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 200 mm Aluminium, anodised, barrel tower bolts of extruded section.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised

S&F 150 mm aluminium, anodised, barrel tower bolts of extruded section.

S&F 100 mm extruded aluminium alloy handles, fabricated type, anodised.

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door shutter, overall length of cover plate 140mm.

S&F mild steel 300 mm long ordinary rat tail rod pattern spring, including roller and roller plate.

M&L in repair for block boards, 18/19 mm thick, grade 1 quality , exterior grade, commercial type, fixed with screws to timber frame work including dismantling of old wooden work.

S&F 100 mm long Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F continuous piano hinge (width of flap 30mm) (when open) mild steel bright finish or electrogalvanised

M&L two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces

M&L two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces.

M&L preparation of old painted wood and woodbased surfaces of any description, not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of old painted steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete in sunken floors exc 15cm thick (above ground level) and disposing the rubbish to low lying areas complete all as specified and directed

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4 with water proofing compound as per manufacturer's instructions, finishing even and fair complete all as specified and directed. (Note: Supply only of WPC shall be measured and paid separately under relevant item).

Supply only integral water proofing compound.

M&L for cement concrete 1:7:12 type F-2 (using 40mm graded brick aggregates) as in foundations, filling and mass concrete complete all as specified and directed

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sunken portion complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust , including brushing neat cement slurry with 3.00 Kg of cement per sqm

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

S&F non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed

S&F non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F glazed ceramic dark coloured tiles 350x250mmx7mm/ 450 x 350 x 7 mm thick, etc. on vertical surfaces such as skirting, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed.

S&F in repair vitreous China Squatting pan 'Orrisa' pattren size 580x440mm white with integral foot rest and PVC (SWR) 'P' trap 110mm bore complete

S&F in repair vitreous China wash basin white,flat back size 550x400mm including CP waste coupling 32mm bore, waste PVC pipe 32mm bore of suiltable length complete

S&F in repair pillar tap for 15mm bore pipe, cast copper alloy, with capstan heads, chromium plated, cast copper alloy, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F in repair 10 ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float and handle complete all as specified and directed

S&F in repair flush pipe of polythylene of low or high density or PVC 32mm dia for low level cistern.

Dismantling water tanks Exc 250 Ltr & not exceeding 500Ltr and S&F rotational moulded polythene, triple layers, white, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including 20mm bore PTMT ball valve epoxy coated minimum weight 210gms with aluminium rod complete all as specified and directed

Taking up or down 15mm dia steel tubing and connections all as specified and directed.

S&F 15mm dia GI tubes medium grade with all fittings and fixed complete to walls and ceiling or laid in floors all as specified and directed.

Fixing only 15mm dia steel tubing and connection in new or old position (in wall ceiling floors etc) including fittings and cleaning for refixing all as specified and directed.

Taking up or down 20mm dia steel tubing and connections all as specified and directed.

S&F 20mm dia GI tubes medium grade with all fittings and fixed complete to walls and ceiling or laid in floors all as specified and directed.

Fixing only 20mm dia steel tubing and connection in new or old position including fittings and cleaning for refixing all as specified and directed.

S&F in repair 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup (concealed type) and fixed.

S&F in repair brass chroumium plated shower rose 125mm size all as specified and directed.

S&F in repair 15mm bore stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

S&F in repair 20mm bore stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

S&F in repair bib taps 15mm dia chromium plated fancy type long body with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repair 100mm dia. stainless steel grating with or without hinge type or hole type complete all specified and directed.

S&F in repair tubular, towel rail brass chromium plated 20mm dia D type 60cm long between flanges all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed..

Taking down eaves gutters and rain water pipes ( any size or pattern) , including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories

S&F 110mm bore PVC (SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2m length including) including all fittings complete all as specified and directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length laid in floor, trenches including all fittings complete all as specified and directed

S&F 75mm bore PVC(SWR) pipes single socketed in any length with rubber ring joint, fixed to walls including taking down eaves, gutters rain water pipes (any size or pattern) including all fittings complete all as specified and directed

S&F 75mm bore PVC(SWR) pipes single socketed in any length laid in floor, trenches including all fittings complete all as specified and directed

S&F 110 mm bore PVC (SWR) bend any radius with access door

S&F 75mm bore PVC (SWR) bend any radius with access door

S&F 110 mm bore (SWR) vent cowl

M&L 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness (below or above ground level) and disposing the rubbish to low lying areas complete all as specified and directed.

Material and labour 75mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of floor.

M&L for coloured Chequered cement concrete tiles with grey cement and no pigment, 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar

M&L black zebra bhainsalana Marble/ green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars and window cills cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete.

M&L for reinforced cement concrete 1:2:4 type B-1 as in shelves, slabs supported on walls, beams, landings, canopies etc. complete all as specified and directed

S&F mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and directed

M&L TMT bars 6 to 8mm dia cut to length bent to shape required including crancking spirally for hooking ends and binding with and including mild steel wire annealed n.less than 0.9mm dia. or securing with clips complete all as specified.

M&L for use and waste of formwork to soffits of shelves, slabs and similar work not exc. 200 mm thick for fair finished flat surfaces of concrete all as specified and as directed.

S&F in repair sinks with drainage board made of stain less steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack size 600mm x 900mm x 250mm deep made out of 0.63mm thick stainless steel sheet (Grade AISI 304) including fixing arrangement complete all as specified and directed

S&F in repair cutrain rod of 25mm bore of mild steel, PVC coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plugs complete all as specified and directed.

Dismantling brick tiles or terracing tiles, single layer on roofs

Demolition of mud in roofs , any thickness , including plastering and leeping (whether full thickness removed or only a part thereof

M&L cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in padding in roof slab to maintain required slope finished even and fair with water proofing compound as per manufacturer's instructions complete all as specified and directed. (Note: Supply only of WPC shall be measured and paid separately)

M&L for 40 mm thick brick tiles laid over 15 mm thick screed bed in cement mortar 1:6 and jointed, grouted flush in cement mortar 1:3 mixed 5% of crude of by weight of cement on roof padding complete all as specified and directed

All as per item No 111 above but except tiles.

M & L for PCC type B1 1:2:4 (20 mm graded aggregate) in bed blocks for hold fast for doors, roof kerbs or mud stops, and the like, rounded or chamfered on edges including weathering slightly rounded and throating complete all as specified and directed.

Material and Labour for repairing to RCC projections, chajjas, roofs, facia, ceiling etc. by scrapping, cutting, chiseling, de-rusting and cleaning exposed reinforcement of damaged loose RCC surfaces and applying neat cement slurry @ 3kg/sqm and filling the surfaces with cement sand mortar 1:3 or cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) using coarse sand in layers as required and reinforced with 8mm dia. TMT bars in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces in any situation and at height upto 7.0m complete all as specified. Notes:- 1. Cost of formwork shall be deemed to be included in unit rate quoted by the Contractor. 2. Flat area shall only be measured and paid.

Excavation in trenches, n exc 1.5m wide and n. exc. 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n. exc. 10 sqm on plan and n. exc. 1.5 m in depth and getting out in soft/loose soil.

All as per Srl item No 115 above but exc 1.50 mtr and n.exc 3.00 in depth.

Demolition and breaking up drain pipes ( salt glazed ware, AC or Reinforced concrete ) 150mm bore set in cement mortar and taking out from trenches as specified and directed.

All as per Srl Item No 117 above but 200 mm bore.

Material and labour for PCC (1:4:8) type D2 (using 40mm graded broken stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore of pipe all as specified and as directed.

All as per Srl Item No 119 above but 200 mm bore.

Material and labour salt-glazed stoneware drain pipes internal diameter 150mm laid in trenches and jointed as specified

All as per Srl Item No 121 above but 200 mm bore.

M&L reinforced concrete pipes 150mm, class NP3 , laid and jointed complete with collars and tested complete all as specified and directed.

All as per Srl Item No 123 above but 200mm bore.

Returning filling in the soil including spreading, levelling, watering and well ramming in layer n.exc 25cm thick each layer complete all as specified and directed.

Removing excavated soil to a distance not exc 50m away and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Material and labour for Plain Cement Concrete (1:3:6) Type C-2 (using 40 mm graded brocken stone aggregate) as in surface channels, drains complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed

Material and labour for Plain Cement Concrete (1:2:4) Type B-1 (using 20 mm graded brocken stone aggregate) as in coping, benching on top surface and the like including necessary moulds and form work complete all as specified and as directed.

Demolition reinforced cement concrete of any description and in any position not otherwise specically provided (reinfocement cut as required to facilitate demolition) complete all as specified and directed.

M&L for pre cast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as cover slab for manhole and similar work etc including form work complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) using approved colour coding, 1100 volts grade, ISI marked, including PVC conduit heavy grade, 20 mm or higher dia. with fittings concealed in wall/ on surface for ceiling with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) 1100 volts grade, ISI marked and connecting to the common earth dolly including provn of 3mm thick plastic laminated sheet of appropriate size and sunken CI/pressed steel terminal boxes for mounting switches, sockets and regulators etc. including cutting chases and making good to the disturbed surfaces as per existing for One light point/fan point/ bell point controlled by one, one way switch complete all as specified and directed.

All as per Srl item No 133 above but one modular socket 6A multipin 2 module on independent board.

All as per Srl item No 133 above but One modular socket, 6A multipurposes 2 module on same board.

All as per Srl item No 133 above but one light point controlled by two way switches.

All as per serial item No.133 here-in-before but with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area), using approved colour coding, 1100 Volt grade ISI marked including PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area) 1100 Volt grade ISI marked as earth continuity conductor and connecting to the common earth dolly for 3 pin 15/16 Amps socket outlet on independent board.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt , FRLS cable of size 6 sqmm including 6 sqmm multistranded copper conductor FRLS cable PVC insulated for earthing duly connected with earth dolly, with approved colour coding including PVC conduit heavy grade, of appropriate dia. concealed in wall with accessories including cutting chases and making good to the disturbed surfaces as per existing and taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F modular switch one way ,1 module 6 amps single pole complete all as specified and directed.

S&F modular socket 6A multipin 2 module complete all as specified and directed.

S&F modular switch one way 16 amps one module single pole complete all as specified and directed.

S&F modular socket, 6A/16A multipin combined 2 module complete all as specified and directed.

S&F switch modular 2 way 6A one module all as specified and directed.

S&F surface mounting universal batten housing made of powder coated CRCA sheet suitable for upto 1 x 18/20 W LED tube and taking down existing old unserviceable housing complete all as specified and as directed.

S&F LED tube 18/20W ultra bright LED polycarbonate tube with efficacy minimum 2000 lumens, CCT > 6500K, PF > 0.90 suitable for fitting into exsting/ new batten housing and taking down existing old unserviceable tube complete all as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report form manufacturer to Engineer-in-Charge for approval before incorporating the items in work

Taking down carefully ceiling fan complete fittings at site removing fans and deposited to MES storeyard for re-fixing after completion of work at the site .

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete including replacement of one pair of Canopy.

S&F in replacement of modular fan regulator 2 module electronic type 5 step 100watt, 240 Volt and connecting complete all as specified and directed all as directed.

S&F Bell, AC, 230 volts, single pole complete all as specified & directed.

S&F bell push modular type 6 Amp 1 module complete all as specified and directed.

Supply and fix for lamp holder, PVC/ polycarbonate type with back plate, brass terminals suitable for lamp holder base of and including 9 watt LED retrofit lamp complete all as specified and as directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate, isolated body

S&F GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting MS clamps with two coats of synthetic enemal paint over a coat of red oxide primer including taking down the existing GI pipe bracket complete all as specified and directed.

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supplying and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with SPN double door complete all as specified and directed. Note : All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed.

S&F in repair MCB single pole 6 amps to 32 amps, 'B' series complete all as specified and directed.

S&F in repair MCB single pole 6 amps to 32 amps, C series complete all as specified and directed.

S&F in repair MCB single pole and neutral 40 amps, C series complete all as specified and directed.

Material and labour for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way including fixing in the wall, cutting chases grouting and necessary patch work and finishes to match with the existing including making connections all as directed containing the followings :- (a) MCCB 4 Pole 100 Amps 16 KA breaking capacity with thermal release - 01 No (In coming) (b) Bus bar made out of Aluminium on insulated duly insulated wire adhesive tape RYB & black -4 Nos (c) MCB SPN 40 Amp-4 Nos, MCB SP 10-32 Amp - 08 Nos (Out going) (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable ampacity as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil complete including dismantling existing all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core. Note: Excavation and earth work, sand cushioning, brick protection, GI pipe shall be measured and paid separately.

Supply and lay brick common burnt sub class "B" old size and for protection of cable laid in trenches for under ground cable all as specified.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers before laying the cable & after laying the cable complete all as specified

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

M/s kulwant singh and sons

buta singh and sons

Harbhajan electric co

GORAYA AND CO

talwinder singh and co

M/S Harjinder Singh Contractor

JOGRAJ CONSTRUCTION COMPANY

D.RAJ And CO.