Establishment of 200 MT Cold Storage at Ilaiyankudi Regulated Market in Sivagangai District

Amount

Clearing the Light jungle in working spot as directed by the Departmental officers.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling of well gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification.

Cement Concrete 1:4:8 (One Cement, Four sand and Eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Damp proof course with Cement Mortar 1:4 (One Cement and Four M.Sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Cement Concrete 1:1-1/2:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

In foundation and basement

In Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For Foundation & Basement

For first floor

Plastering with Cement Mortar 1:5 (One cement and Five P.sand ), 12mm thick in all floors including curing etc. complete complying with standard specification

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Providing and painting interior walls & ceiling with two coats of Plastic emulsion paint over one coat of primer including thorough scraping, clean removal of dirt. The rate includes cost of brushes, Sand paper, plaster of parries, putty wherever required and neat finishing etc.,

Providing and painting exterior walls with Two coats of exterior weather proof emulsion paint ove rone coat of primer including thorough scraping, clean removal of dirt. The rate includes cost of brushes, Sand paper, plaster of parries, putty wherever required and neat finishing etc.,

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete

Vacum dewatering on freshly laid and thoroughly vibrated concrete surface to produce a homogeneous and smooth concrete surface .Suction matshall be spread over the levelled fresh concrete surface and shall be connected by the suction hose to the vaccum pump for dewatering of surplus water in the concrete

Providing Groove cutting in flooring concrete for 10mm width and 20mm depth and filling the groove with combination of Anabond Tuffseald 2G and bitumen tar including cost of all materials and labours etc complete.

Supplying and fixing of rolling shutters with ISI mark shall be of pull and push type made out of 18/Gauge x3’’ lathe sections which consists of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below; Curtain; Shall be of 18/Gx3' lath sections cut to required size and filled with heavy cast iron/ M.S. Clips for 8'0"[2.45m] high rolling shutter lathe sections provided shall be not less than 37 numbers. Lock Plate; Shall be 10gaue M.S.Sheet reinforced with 40mmx 6mm M.S angles at the bottom and fitted with heavy latches of 12mm thick locking arrangements on either sides.

Rolling shutter

Gear operated type (from 8 m2 to 12 m2 area)

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessaryThe welding should be done with submerged arc welding to full length. The rate inclusive of the cost of painting the memebers with one coat of primer of Zinc chromite and enamel paint etc., complete

Fabricating supplying and erecting the Pre-engineered steel building structure using Galvanised structural steel sections, conforming to Grade 50 with yield strength of 345MPa baseplate, Sag Rods, struts including cleats to receive 'Z' and 'C' purlins, cutting, drilling holes, welding, grinding fixing the members with nessary bolts nuts, anchor bolt of approved quality, hoisting, aligning and placing the 'I' sections in position as per the design got approved

Supplying and laying of Gal volume sheet 0.50 mm thick of approved quality for roofing with necessary U or J bolts and unts bitumen GI washers etc., complete complying with standard specification.

Supplying and fixing of Galvolume sheet flashing approved quality with necessary U or J bolts and nuts GI washers etc., complete complying with standarad specification.

Supplying and fixing of profile colour coated Galvalume Eave Gutter of size 217x16.8x154mm made of colour sheet 1.00mm thick with yield strength of 550 MPA of high tensile / C.R. sheets of approved quality for roofing with nessasary fixing arrangemennts with the 'C' purlins provide at the edges 160mm dia rain water downfall pipe etc., complete as directed by the departmental officers.

Supplying and fixing corrugated Poly Carbonate sheet of size 3mx1.06m on the roof inbetween the colour coated Galvolume sheets for propre llighting with nessary scrws and EPDM rubber washers, etc., as complete Complying with standard specification and as directed and specified by the departmental officers.

Supplying and fixing of Gal volume sheet ridge pieces approved quality with necessary U or J bolts and nuts GI washers etc., complete complying with standarad specification

Providing Pre construction of Anti termite Treatment for the Construction of building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment, spraying chemicals and other incident charges etc.,complete.

Stage 1: Spraying Anti termite treatment chemical solution for the foundation before laying the foundation concrete at bottom and sides of the foundation.

Stage 2: Spraying Anti termite treatment chemical solution to the grade beam level, spraying has to be done for the grade beam, brick masonry in the super structure in contact with back fill earth.

Stage 3: Spraying Anti termite treatment chemical solution on M.Sand for the flooring before laying the flooring concrete; the treatment has to be carried out on the M.Sand filling in basement and after leveling operation is over.

Stage 4: Spraying Anti termite treatment chemical solution around the building on outside by making crow bar holes at an interval of 15 cms to a depth of 30 cms before laying the plinth projection. These holes have to be closed after the treatment.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing, applying & finishing 2mm thick self levelling Epoxy Floor Coating over a coat of Epoxy Primer for flooring. ( Epoxy Top Coat application by Combined With Resin and Harner Material to getting desire Color as approved by the engineer incharge).,

Supplying and fixing of PVC prefabricated sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 for wall panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of PVC prefabricated sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 for ceiling panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of PVC prefabricated sandwich 100mm thick puf panels with rigid puf injected CFC free polyurethane foam as insulation and precoated GI sheet 0.50mm thick on both sides as skin materials and having density of 40 Kg/m3 with vapour matt for flooring panels of cold room and precooling room complete as directed by the departmental officials

Supplying and fixing of Sliding Door size 2400x3000x80mm with manual opening anti condensate self limiting, regulating energy saving door, Human safety door release, Heavy duty latches for cold room with necessary locking arrangements complete as directed by the departmental officials

Supplying and fixing of Suitable Door size 2400 x 3000 x 80 mm pvc strip curtain for Cold room door complete

Supplying and fixing of Suitable Door size 2400 x 3000 x 80 mm of Air curtain for Cold room door complete

Supplying and fixing 100 mm puf panels accessaries and flashing complete

Supply and fixing of 12 KW EMERSON / DAIKIN make Refrigeration capacity @ 0o C Evaporation Temperature / 54o C Condensing Temperature, inbuilt with scroll Compressor, Air Cooled Condensing unit Ultra cool make Evaporator unit operate with R410 A Refrigerant. The unit should contain Condenser fan, Compressor , Accumulator, Pressure control HP/LP Switch , LLSV Drier, Valve with all accessories. Suitable capacity Evaporator unit casing with energy efficient Inner Grooved Copper Coil Humidity to be maintained around 90% and also equipped with expansion valve, Dynamically balanced Compact fan motor with blade fitted in built thermal protection

Supplying and Fixing copper pipe for 12 KW Suction and Liquid line Tubular insulation

Supplying and Fixing Electrical Control panel for 12KW Refrigeration unit .

Supplying and Fixing of Electrical cable for 12 KW internal wiring of Condensing unit, Evaporator unit .

Supply and fixing Of 7 KW EMERSON / DAIKIN make Refrigeration capacity @ 0o C Evaporation Temperature / 54o C Condensing Temperature, inbuilt with scroll Compressor, Air Cooled Condensing unit Ultra cool make Evaporator unit operate with R410 A Refrigerant. The unit should contain Condenser fan,Compressor , Accumulator, Pressure control HP/LP Switch , LLSV Drier, Valve with all accessories. Suitable capacity Evaporator unit casing with energy efficient Inner Grooved Copper Coil Humidity to be maintained around 90% and also equipped with expansion valve, Dynamically balanced Compact fan motor with blade fitted in built thermal protection

Supplying and Fixing Electrical Control panel for 7 KW Refrigeration unit .

Supplying and Fixing copper pipe for 7 KW Suction and Liquid line Tubular insulation

Supplying and Fixing of Electrical cable for 7 KW internal wiring of Condensing unit, Evaporator