Repairs to fencing, gate including their periodicals services in zone I to VI and interlocking tiles/ chequered tiles/hardstanding at CME

Amount

Demolition of Brick work or stone / boulder masonry built in cement mortar complete all as specified incl coping all as directed.

M & L for pre cast PCC block masonry Type C-1 1:3:6 using 20mm graded stone aggregate, exc 10 cm width and set in CM 1:4 all as specified and directed.

Demolition of cement concrete (un re-inforced) in ground floor and paving not exc. 15 cm thick below or above ground level complete all as specified and directed.

M&L cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L 15mm thick cement plastering on concrete surfaces in CM (1:4) finishing surfaces even and smooth without using extra cement complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground etc. complete all as specified and directed.

Dismantling fencing wire mesh, any type all as directed.

S&F MS angle as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 etc. complete all as specified and as directed.

Supply only Chain link MS galvanisd fencing, any size or type etc. complete all as specified and directed by Engr - in - charge

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire etc. complete all as specified and directed.

S & F 5 to 10 mm dia. of neck, mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long etc. complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for reinforcement cut as require to facilitate demolition all as directed.

M&L reinforced cement concrete (nominal mix)Type B1 1:2:4, using 20mm graded stone aggreagate as in footing, columns etc complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter etc. complete all as specified and directed.

S&F mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as specified and directed.

S&F mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as specified and directed.

S & F in repair galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) etc. complete all as specified and directed.

M & L preparation of new or previously untreated surfaces of steel of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide zinc chrome primer complete all as specified and directed

M & L preparation of old surfaces of steel of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing etc. complete all as specified and as directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M & L hardcore of guage exc 63mm but not exc. 100 mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and directed.

M&L 100 mm thick PCC type B-2 (1:2:4) using 40 mm graded aggregate as in sub base etc complete all as specified and directed

M&L 25mm thick PCC type B-1 (1:2:4) using 20mm graded aggregate as in floor finish with and including finished surface fair and even, groom finish etc complete all as specified and directed

M&L forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' etc complete all as specified and directed.

M&L 20 to 25 mm thick rough dressed sand stone slab flooring, laid dry but jointed and pointed in cement mortar 1:3 etc. complete all as specified and directed.

All as per item No. 27 above, but except stone Note : serviceable stone slab obtained from sl item No.22 shall be re-used in this item.

M&L 60mm thick machine pressed precast concrete interlocking paver block reflective type coloured any shape and size confirming to IS 15658-2006 of M-35 grade, with grey cement and pigment complete over and including 25mm sand cushioning all as specified and directed.

M& L filleting in any position and to any shape in cement mortar 1:4 including all mitres, stops, including sectional area not exc. 25 Sqcm etc complete all as specified and directed.

M&L chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 etc. including dismantling old tiles etc. complete all as specified and directed.

M&L vitrified tiles of 400x400mm,11 to 12mm thick mat rough finish, breaking strength =1500N, modulas of rupture 38N/mm2, bulk density =2.2 per gm/cc, colour resistance to uv light as in parking tiles etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, and Including dismantling old tile and make: Johnson and equivalent etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. Complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc. complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, with and including one shop coat paint complete all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed

M&L cement concrete type C-2, 1:3:6 (using 40 mm graded aggregate) as in foundation, filling and mass concrete etc. complete all as specified and directed.

(Applicable for above all items)

Contrator has to employ skilled/unskilled tradesman with adequate experience & required documents to be submitted to office. The rate shall be quoted by the contractor including scaffolding to carry out the work for height more than 10.00 mtrs.

Labour should wear contractors uniform with firm logo, failing which recovery should be made.

Minimum of 02 x teams of each trades shall be available for maint of urgent nature whenever called upon of any trade, failing which recovery will be initiated for not employing adequate labour at site.

Site clearance shall be done by contractor after finishing work and obtain the signature of occupant as the site clearance has done. The same shall be verified and put up before issue of completion certificate.

All Scarps will be done with mechanical scaper

Mechanical scaper should be deposited in our store at the time of sample approval

vishalconstruction

TUSHANT CHOUDHARY

BSK Construction

Decent Decorators