ADDITION/ ALTERATION TO TELEPHONE EXCHANGE BLDG No 06 AND RECREATION CLUB BLDG No 151 OF DMRL HYDERABAD

Amount

Taking down existing roof treatment of any position with bituminous felt including plaster / loose concrete and removing rubbish out side Mod land and roughing the surface of old concrete by picking, scraping, cleaning and washing down with water to remove all dust etc all as specified and directed.

M&L Cement concrete 1:2:4 ( 1 cement ; 2 coarse sand : 4graded stone aggregate 12.5 mm nominal size ) in levelling coarse, laid in required slope and camber in panels as required including consolidation finishing and tamping complete

M&L for rendering 10mm in CM 1:3 over concrete surfaces on RCC roof slab and parapets mixed with WPC @ 3% by weight of cement shall be carried out complete all as specified and directed by Engr-in-Charge. Note : WPC will be measured under separate item of this schedule.

Supply only integral water proofing compound Make :- SCOTT AQUA PROF/RAILIA/IMPERMO/FOSROC/CICO

Providing and carry out water proofing treatment to sound, moisture free concrete surface system includes proper surface preparation to remove loose dust, dirt, loose mortar , curing compound etc carry out cementitious injection grouting at leakage points and construction joints using cement slurry modified with Cebex 100 plasticized expansive ground admixture supplies in 225 gm pouch, treatment of construction joints using polymer modified mortar prepare by using Nit bond SBR latest's, application of polymer modified batter at floor, wall junction, filling of annular space around rain water outlet using contexture GP2 non shrink cementoinous grouts. Adulated surface and pot hole shall be treated with epoxy mortar or putty to obtained sound/ leveled surface. Application of primer Into proof WB primer on sound mortar slab surface. Followed by application of coat of Into proof 600 PF liquid applied single component pitch free polyurethane coating supplied in 25 kg drum coverage @ 2.30 Kg/ m2 to achieve 1.5mm thickness in two coats complete including all tools and tackles as per manufacturers specification. Coating shall be having crack bridging of 2mm, elongation ( ASTMD 124 ) greater than 600 percentage, tensile strength ( ASTM D412) , 2.5 N/MM2 , recovery from elongation ( ASTM D412) , 95 percentage, 85 percentage of solid continents, tear resistance ( ASTM D624) , 15 KN/M, shore A hardness ( ASTM D2240) , 60, water vapour transmission not more than 1 gm / M2 ,water permeability ( DIN -1048) - NIL, services temperature - 40'c to 70 degree 'c , flash point greater than 70'C HSE guidelines :- It is recommended to provide adequate general and local exhaust ventilations, providing protection to Eye, face, Hand and other skin by wearing appropriate glouse, Google, face cilid, respiratory protectionist. directed in SDS of the product.

Crazy marble stone flooring , including filling the gaps with light shade pigment with white cement marble powder mixture ( 3 parts of white cement : 1 part of marble powder by weight in proportion of 4:7 ( 4 cement marble powder mix : 7 white black or white and black marble chips of size from 1mm to 4 mm nominal size by volume) with under layer 25mm thick cement concrete 1:2:4 including rubbing, polishing & cement slurry etc complete

Preparation of old painted surface, over 10 cm width or girth, not otherwise described and applying one coats of aluminum paint (ordinary tint) complete all as specified and as dirrected.

Earth work in surface excavation in any kind of soil not exceeding 30cm in depth but exceeding 1.5m in width as well as 10 Sqm on plan including getting out and disposal of excavated earth up to 50m and lift up to 1.5 m as directed by Engr -in- charge

Excavation work by mechanical means ( Hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5m in width or 10 Sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m :- (i) Ordinary rock

Disposal of building rubbish / melba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground out side MoD Land all leads including all lifts involved.

Returning filling in trenches incl spreading, levelling , watering& well ramming in layers n.exc 25 CM thick complete all as specified and as directed.

Supplying and filling in plinth / under floor with sand under floors including watering, ramming, consolidating and dressing complete

Supplying , filling, spreading and no spreading hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

Providing and laying 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size derived from natural sources) in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level

M&L for Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:4 complete

M&L providing Half brick masonry with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in super structure above plinth level up to floor V level in cement mortar 1:4

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground Out side MoD Land

M&L 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

M&L 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

M&L 6mm thick cement plaster 1:3 ( 1 cement : 3 fine sand) on ceiling surface finished with a floating coat of neat cement and thick coat of lime wash on top of ceiling when dry for bearing of RCC slabs and beams

Distempering Two or more coats on new work over a coat wall primer with Its quality acrylic distemper , having VOC ( Volatile Organic Compound) content less than 50 grams / liter of approved brand and manufacture of required shade and colour including applying 1mm thick wall care putty complete as per manufacturer's specification

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping , sand papering and preparing the surface smooth including necessary repairs to scratches etc complete

Distempering on old work ( wall/ ceiling) ( one or more coats) with 1st quality acrylic distemper ( Ready mix ) having VOC content less than 50 grams/ liter of approved brand over a coat of water thinkable cement primer and manufacturer to give an even shade

Finishing wall New work ( Two or more coats applied @ 1.43 liter/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 liter / 10 Sqm with 100 % premium acrylic emulsion paint having VOC less than 50 gm/ liter and UV resistance as per IS 15489 : 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot tinted ) with silicon additives

M&L for preparation of newly plastered surface of ceiling and applying two coats of distemper oil emulsion over a coat of primer complete all as specified

Making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20mm nominal size derived from natural sources) of 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand , including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying ceramic Non skid floor tiles of size 300 x 300 mm or more ( thickness to be specified by the manufacturer) of !st quality conforming to IS : 15622 of approved make in colours and shade except white ivory, Grey, fume Red Brown, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 Kg/ Sqm including pointing the joints with white cement and matching pigment etc complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer) of approved make, in all colours, shades except burgundy, bottle green, black of and size as approved by Engr -in- charge , in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 ( 1 cement ; 3 coarse sand) and jointing with grey cement slurry @ 3.3 Kg per Sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing aluminiuim extruded section body universal type hydraulic door closer ( having brand logo with ISI , Is : 3564, embossed on the body, door weight up to 36 to 80 kg and door width from 701 to 1000mm) with double speed adjustable with necessary accessories and screws etc complete

Providing and laying in position ready mixed or site batched mix cement concrete for reinforced cement concrete work using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolanna / Ordinary Portland / Portland slag cement admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete , to improve durability and workability without impairing strength including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engr-in- Charge for the following graded or concrete all works up to plinth level . (i) Concrete of M-25 grade with minimum cement content of 330 Kg/ Cum for beam, lintel

Providing and laying in position ready mixed or site batched mix cement concrete for reinforced cement concrete work using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolanna / Ordinary Portland / Portland slag cement admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete , to improve durability and workability without impairing strength including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engr-in- Charge for the following graded or concrete all works above plinth level up to floor V level. (i) Concrete of M-25 grade with minimum cement content of 330 Kg/ Cum for beam, lintel

Centering and shuttering including strutting, propping etc and removal of form for lintels, beams, plinth beams, girders, resumes and cantilever

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete above plinth level :- (i) Thermo - Mechanically Treated bars of grade Fe- 500D or more

Steel reinforcement for RCC work ready to use "cut and bend" rebars of approved make from factory / workshop to construction site including placing in position and binding all complete above plinth level . (i) Thermo / Mechanically Treated bars of grade Fe- 500D or more

Making the opening in brick masonry for door/ window/ clerestory window including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i/c disposal of melba / rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer -in-Charge

Steel work in built up tubular hot finished welded type tubes ( round, square or rectangular hollow tubes etc) trusses etc including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc complete

Providing and fixing steel work in gratings, frames, guard bars, ladders, railing, brackets, purlings, gates and similar works welded in built up sections / frames work, including cutting, hoisting, fixing in position and applying priming coat of approved steel primer using structural steel as required

Providing and fixing 0.56mm aluminum color coated profile with centre to centre pitch of 175mm , depth of 46mm, top crest width of 41mm, bottom valley width of 80mm overall profile width of 1144, cover width 1050mm at all height, levels and locations colour finish aluminum alloy roofing sheets of alloy IS designation 31500, temper H x8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance.

Painting on new steel surface ( two or more coats ) including a coat of approved steel primer ( red oxide primer) with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

Cutting chases in brick masonry walls for 25mm dia pipes and making good the same with cement concrete 1:3:6 including necessary plaster and pointing in cement mortar 1:4 ( 1 cement : 4 coarse sand)

Dismantling tiles work in floors and roof laid in cement mortar including stacking materials within 50 meters lead. (i) for thickness of tiles 8mm to 25mm

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc complete on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) :- (i) Light shade pigment using white cement

Providing and fixing 12.5mm thick tapered edge Glass reinforced Gypsum board conforming to IS : 2095 (Part 3) : 1996 false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from MS sheet and galvanized with zinc coating of 120gms/ Sqm ( both side inclusive ) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm at 1200mm centre to centre, one flanges fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x 10 x,50mm of required length with nut & bolts of required size , Gypsum board of 12.5mm thick with white paper layer on face side of size 600 x 600 mm as directed

S&F venetian blinds (vertical type) of 100mm wide straps with all fittings (to be matched with existing patters) & taking down old venetian blinds complete all as specified and as directed.

Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window cills, facials and similar locations of required size, approved shade , colour and texture laid over 20mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joint treated with white cement mixed with matching pigment, epoxy touch ups including rubbing, curing, moulding and polishing to edges to give high gloss finish etc complete at all levels (i) Granite stone slab colour black, cherry / ruby Red , area of slab up to 0.50 Sqm

Providing edge moulding to 18mm thick granite stone counters, Vanities etc, including machine polishing to edge to give high gloss finish etc complete as per design approved by engr -in-charge

providing and fixing pressed steel door frames conforming to IS: 4531, manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25mm, or base ties of 1.60mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre- treatment of the surface as directed by Engineer -in- Charge :- (i) Profile 'E' fixing and adjustable lugs with split end tail to each jambs

Providing and fixing second class teak wood 35mm thick panelled or panelled and glazed shutter for door fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer -in- Charge

Providing and fixing wire gauge shutters using galvanized MS wire gauge of average width of aperture 1.4mm in both directions with wire of dia 0.63mm, for doors, windows and clerestory windows with hinges and necessary screws :- (i) 35mm thick shutter withISI marked MS pressed butt hinges bright finished of required size second class rad wood kiln seasoned

Providing and fixing factory made door frame ( single rebate ) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62mm width & 32mm thickness , frame will be mitered & jointed with self driven self tapping screws of size 38mm x 4mm & PVC solvent cement including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification and direction of engineer -in- Charge.

Providing and fixing factory made 30mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with MS tubes of size 33mm x 17mm x 1mm, painted with primer, all four corners of reinforcement to be welded or sealed. solid PVC extruded bidding ( push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitered cut and joint with help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturer's specifications and direction of Engineer -in- Charge. (i) Decorative finish ( both side wood grained finish)

Providing and fixing ISI marked MS pressed butt hinges 100 x 58 x 1.90mm bright finished with necessary screws etc complete

Providing and fixing aluminum handles 125mm , ISI marked , anodized ( anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminum tower bolts 150 x 10mm, ISI marked, anodized ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminum sliding door bolts 300 x 16mm , ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nut and screws etc complete

Providing and fixing aluminum Twin rubber stopper hanging floor door stopper, ISI marked, anodized ( anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade , with necessary screws complete

M&L Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling CP brass/ stainless steel screws, all complete as per architectural drawings and the directions of engr -in- Charge. (Glazing, paneling and dash fasteners to be paid for separately) :- (i) For fixed portion powder coated aluminum ( minimum thickness of powder coating 50 micron)

(ii) For shutters of doors, windows & ventilators powder coated aluminum ( minimum thickness of powder coating 50 micron) including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required ( Fittings shall be paid for separately)

M&L Proving and fixing glazing in aluminum door, window, ventilator shutters and partitions etc with EPDM rubber / neoprene gasket etc complete as per the architectural drawings and the directions of Engineer-in-charge:- (i) With float glass panes of 5mm thickness ( weight not less than 12.50 Kg/ Sqm)

S&F 12mm thick both side prelaminated particle board to aluminum door, partition complete all as specified

M&L Providing and fixing steel work in gratings, frames, guard bars, ladders, railing, brackets, purlings, gates and similar works welded in built up sections / frames work, including cutting, hoisting, fixing in position and applying priming coat of approved steel primer using structural steel as required

M&L Painting two or more coat on new wood work with synthetic enamel paint of approved brand and manufacture to give an even shade

M&L Providing and fixing GI pipes 15mm dia nominal bore complete with GI fittings and clamps i/c making good the walls etc concealed pipe including painting with anti corrosive bit mastic paint cutting chases and making good the wall

Providing and fixing 20mm dia nominal bore GI pipes complete with GI fittings and clamps, i/c cutting and making good the walls etc

Providing and fixing CP brass long nose bib cock 15mm nominal bore of approved quality conforming to IS standards and weighing not less 410 gms

Providing and fixing CP brass angle valves 15mm nominal bore for basin, mixed, geyser, urinal etc points of approved quality conforming to IS 8931

Providing and fixing 15mm dia pillar taps cast copper alloy with capstan head of approved quality and design complete

Providing and fixing gun metal gate valve 20mm nominal bore with CI wheel of approved quality ( screwed end) complete

Providing and fixing 75mm dia sand cast iron S&S trap of self cleansing design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors

Providing and fixing square mouth S.W gully trap class SP-1 complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300 x 300 mm size ( inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :- (i) 150 x 100 mm size P type with common burnt clay F.P.S ( non modular) bricks of class designation 7.5

Dismantling CI or asbestos rain water pipe with fittings and clamps including stacking the materials within 50 meters lead :- (i) 100mm dia pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type 'A' including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion single socketed pipes :-

75mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type 'A' including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion :-

Bend 75mm dia

Bend 110mm dia

Coupler 110mm dia

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :- (i) White vitreous china flat back wash basin size 550 x 400mm with single 15mm CP brass pillar tap

Providing and fixing white vitreous china pedestal type water closet ( European type WC pan) with seat and lid , 10 liter low level white PVC flushing cistern, including flush pipe, with manually controlled device ( handle lever), conforming to IS : 7231, with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required :- (i) WC pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580 x 380 x 350mm with white PVC automatic flushing cistern, with fittings, standard size CP brass flush pipe , spreaders with unions and clamps ( all in CP brass) with waste fittings as per IS : 2556, CI trap with outlet gratings and other couplings in CP brass including painting to fittings and cutting and making good the walls and floors wherever required :- (i) Single half stall urinal with 5 liter PVC automatic flushing cistern

M&L Providing and fixing PVC waste pipe flexible pipe 32mm / 40mm dia for sink or wash basin and urinal including PVC waste fittings complete

M&L Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangements of approved quality and colour 600mm long

M&L Providing and fixing plasticized PVC connection 15mm nominal bore x 45 cm length pipe with PTMT nuts, collar and bush of approved and colour

M&L Providing and fixing 600 x 450 mm beveled edge mirror of superior glass ( of approved quality0 complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete

M&L Disconnecting damaged over head / terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engr -in- Charge

M&L Providing and placing on terrace ( at all floor levels) polyethylene water storage tank, 1000 ltr capacity Is: 12701 marked , with cover and suitable locking arrangements and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

M&L Providing and fixing PTMT ball cock of approved quality , colour and make complete with Epoxy coated aluminum rod with LP / HP HD plastic ball :- (i) 20mm nominal bore 120mm long , weighing not less than 198 gms

M&L Providing, laying and jointing glazed stoneware pipes class SP- 1 with stiff mixture of cement mortar in the proportion of 1:1 ( 1 cement : 1 fine sand) including testing of joints etc complete :- (i) 150mm diameter

M&L Providing and laying cement concrete 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W pipes including bed concrete as per standard design :- (i) 150mm diameter S.W pipe

Providing and laying cement concrete in retaining walls, return walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, sunken floors etc up to floor five level excluding the cost of centering shuttering and finishing :- (i) 1:2:4 (1 cement : 2 coarse sand ( zone -III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources )

Reinforced cement concrete work in beams, suspended floors, roof, manhole cover having scope up to 15 landing, balconies, shelves etc above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5 : 3 ( 1 cement : 1.5 coarse sand (Zone - III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources ).

Providing and laying Double charge vitrified tiles size 600 x 600mm in floor in different size ( thickness to be specified by the manufacturer ) with water absorption less than 0.08 % and conforming to IS : 15622 of approved brand & manufacturer, in all colours and shade , laid on 20mm thick cement mortar 1:4 jointing with grey cement slurry @ 3.3 kg/Sqm including grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, pier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.

Providing and laying vitrified tiles in different sizes ( size of tiles 600 x 600 mm) ( thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours & shade , in skirting, riser of steps , over 12mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand), jointing with grey cement slurry @ 3.3 Kg / Sqm including grouting the joint with white cement & matching pigments etc complete

Demolishing cement concrete manually / by mechanical means including disposal of materials within 50 meters as per direction of Engr -in- Charge

Dismantling aluminum / gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable materials and stacking of serviceable materials within 50 meters lead as directed by Engr -in- charge

M&L White washing on new work ( three or more coats) with lime to give an even shade to walls

M&L White washing on old wall / ceiling surface ( one or more coats) with lime to give an even shade complete

Finishing wall with Acrylic smooth exterior paint on old work ( two or more coats applied @ 1.67 ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 kg/ 10 Sqm of required shade and 1mm thick wall care putty complete

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc complete and applying white wash with lime to give an even shade on old surface ( two or more coats)

Painting to wooden / steel surface with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade one or more coats of old surfaces complete

Taking out doors, windows and clerestory window shutters ( steel or wood) including stacking within 50 meters lead :- (i) of area 3 Sqm and below

Dismantling doors, windows and clerestory windows ( steel or wood) shutter including chowkhats , architrave, holdfasts etc complete and stacking within 50 meters lead :-

Area 3 Sqm and below

Area beyond 3 Sqm

Providing and fixing in repairs water closet squatting pan ( Indian type WC pan) with 100mm sand cast iron P or S trap, 10 liter low level white PVC flushing cistern including flush pipe, with manually controlled device ( handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :- (i) white vitreous china orrissa pattern WC, pan of size 580 x 440 mm with integral type foot rests

Demolishing brick work in cement mortar manually / by mechanical means including stacking of serviceable materials and disposal of unserviceable materials within 50 meter leads as per direction of Engr -in- Charge

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable materials and disposal of unserviceable materials within 50 meters lead

Taking down carefully of any type point wiring light fans socket or power complete fitting such as switch ceiling roses, pendent, regulator, sockets etc removing material and making good disturb surface of wall floor etc complete

Point wiring complete with 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, drawn through and including 20mm dia rigid PVC conduit medium grade ISI marked and conduit accessories, concealed in block masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of modular metal flush boxes metal galvanised flush boxes (ISI marked) suitable for modular and piano type switches /sockets of any modules /size as required at site including modular plate cover for housing switches, sockets, regulators etc., including 1.5sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed for. NOTE: (i) The quoted rate shall deemed to include the cost of metal flush boxes, modular white cover plate, provision of blank plates as per requirement etc.(ii) Quoted rate shall deemed to be include cost of making necessary chases in walls for inserting metal boxes and making good the disturbed surfaces to match with existing

One light / fan /exhaust /bell point controlled by one 5 amps one way modular switch

One ceiling fan point /Exh fan point controlled by one 5 Amps one way switch and regulator

One 3 pin 5 Amps switch socket outlet point on independent board

One bell point controled by one bell push switch

One 3 pin 5 Amps socket outlet point on same board

S&F modular type Socket 16 A, 230V, AC Supply , ISI marked complete

S&F modular type Socket 6 A, 230V, AC Supply , ISI marked complete

S&F modular fan step type regulator two module

S&F modular type switch 16 A, 230V, AC Supply , ISI marked complete

S&F Ceiling rose ,3pin, 5amps ISI marked , 230V, AC Supply , ISI marked complete

S&F Call bell/Buzzer , 230V, AC Supply , ISI marked complete

Point wiring complete with 2.5 sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, drawn through and including 20mm dia rigid PVC conduit medium grade ISI marked and conduit accessories, concealed in block masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of modular metal flush boxes metal galvanised flush boxes (ISI marked) suitable for modular and piano type switches /sockets of any modules /size as required at site including modular plate cover for housing switches, sockets, regulators etc., including 2.5sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed for one light / fan /exhaust /bell point controlled by one 5 amps one way modular switch, complete all as specified and directed. @ Rs 275x7RM=1925 ofr each point. NOTE: (i) The quoted rate shall deemed to include the cost of metal flush boxes, modular white cover plate, provision of blank plates as per requirement etc.(ii) Quoted rate shall deemed to be include cost of making necessary chases in walls for inserting metal boxes and making good the disturbed surfaces to match with existing

S&F in repair modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 03 Nos and 01 Nos of 16 Amps socket on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal elctrical connections with copper conductor complete

S&F in repair modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 04 Nos on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal elctrical connections with copper conductor complete

S&F Batten in repair FittingLED luminaire 20 W 5700K complete with all accessories prewired and including connection up with three core twister flexible copper conductor cable with suitable size complete removing unserviceable fittings all as specified and directed. Make:- Havells Cat part No. ENDURAPEARLSL 20WLED 757SASYTOPCMP/Philips Cat part No. BRP042 LED 19 CW MR S1 PSU GR or equipement in Wipro

Supply and fixing in repair LED street light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply & fix in repair LED down lighter,fully diffused recessed/surface mounted 2'x2', 36 W, 6500K, fully diffused,CCT, Luminous efficacy of not than 120lm/watt designed for metric false ceiling type or alongwith frame suitable for Armstrong/US Gypsum or similar mounting system with concealed or exposed 'T' sections, Glare free light alongwith electronic driver complete with all accessories preired and connecting up with three core twister flexible copper conductor cable with suitable size complete all as specified and directed. Make :- Havells Cat part No. PLANO2X2PLR36WLED857S or equivalent in Philips/Wipro

LED Flood light, 70Watt, with aluminium pressure die-cast housing, high purity PC Fresnel diffuser with silicon gaskets for IP-65 protection, power consumption less than or equal to 70W and luminaire lumen greater than or equal to 7000 lumuns luminaire efficiency > 100 lu/w in built electronic driver prewired upto terminal block, colour temperature 5700K, surge protection in CM-3.5KV, constant current-constant voltage operated driver with range 150-270V AC including connecting with 3 core PVC copper cable 1.5 sqmm drawn through the bracket and all spares required at site complete all as specified and directed. Make: Wipro cat LR-02-781-XXX-57-G2 /Havells cat part No. ENDURACITY LINEAR NEO SL 70W LED 757PASYBOTG or techno commercially equivalent in Phillips

Supply & Fixing Wall mounted fans 230 Volts single phase oscillating 450 sweep suitable for wall mounting ,oscillation up to 90º and metal body powder coated with all fixing arrangments to fix on wall, including provision copper bunched flexible three core 1.5sq.mm PVC insulated cable from ceiling rose to fan including marking MES Number on fan motor complete all as specified and directed. Make: CG/Havells/Almonard

Supplying and fixing in repair 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. for single pole

S&F in repair MCB SPN 240 Volts 40 Amps complete

Supplying and fixing in repair, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc.of 63A capacity

Supplying and fixing DP sheet steel enclosure on IP-43,Protection along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required

Supplying and fixing TPN sheet steel enclosure on IP-43, Protection along with 16/25/32 A 415 V "C" curve TPN MCB complete with connections, testing and commissioning etc. as required

Supplying and fixing of following ways IP-43,Protection, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required) of 4 way (4 + 12), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on IP-43,Protection complete with tinned copper bus bar, neutral bus bar, earth bar,interconnections, powder painted including earthing etc. as required of 12 way double door complete

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on IP-43, Protection, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required. of 8 way double door complete

M&L Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ concealed PVC conduit 25 mm steel conduit as required for 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 16 sq. mm earth wire

4 X 10 sq. mm + 2 X 10 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 4 sq. mm + 2 X 4sq. mm earth wire

Earthing complete with GI earth plate electrode 600mm x 600mm x 6.0mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth 4mm , GI earth wire shall be protected by 15mm dia GI pipe 'medium grade', watering pipe 20mm dia GI pipe 'light grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL, and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 50mm thick RCC cover (1:2:4) type B1 mix with 8mm dia nominal reinforcement @ 75mm c/c both ways etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciified and as directed. NOTE:-1 Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. GI wire above 7.5m will be measured and paid seperately

Providing and laying in repair earth connection from earth electrode with 4.00 mm dia GI wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. of 6 way double door complete

S&F 3P+N+E Insulated Plug & socket with 40 to 100 Amps TPN MCB, 415V Type 8 as incomer flush to wall including taking dwon old one complete and making good of distructed surface including taking down old one complete all as specified and directed.

S&F 25mm dia rigid non -metallic PVC conduit exclusive of boxes (juntion/RM terminal) but inclusive of all tees, bends, elbows, reducers , bell mouth tube ends and fixing accessories such as couplers , lock nuts, saddles pipe hooks etc.

Supply & fix BLDC fan with remote control ceiling fans complete with blades down rods electronic regulator and acessories , 230 volts single phase 1200 mm sweep min air delivery 210 CFM with service value complete all as specified and directed.

Supply & fix Heavy duty exhaust fan 300mm sweep ,900RPM with aluminium louvers and shutters suitable for 240V single phase AC supply with all fixing arrangments to fix on wall, including provision of 3-way porcelain connector, copper bunched flexible three core 1.5sq.mm PVC insulated cable from connection point to fan, complete all as specified and directed.

Earthing complete with CRPI tested maintenance free chemical tripod earthing using 20mm copper bonded 3m long rod (3Nos) using X-Zel Part I and Part II 20 KG each and Z-Earth 40 KG including inter connection with earth lead burried directly in ground (earth pit not less than 4.0 M deep below normal ground level) with top edge of the electrode 1.5M below normal ground level connected to copper earth strip 25x3mm (up to 7.5m in length from the earth electrode) by means of bolts, and nuts check nuts and washers of galvanised iron or steel all as specified and shown in electrical plate No 5 of SSR part I including necessary excavation & earthwork in any type of strata, PCC (1:3:6) type C-1 earth chamber, 40mm thick RCC cover (1:2:4) mix with 8mm dia TMT bars @ 150mm c/c both ways etc complete and connected to earthing test point complete including testing on completion all as specified and as directed.

M&L XLPE insulated ,armoud, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 150 sq mm 3½ core complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth strip of 25x4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and directed.

Earth continuity copper of size 25mm x 5mm ormain earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc .

Supply and fixing following rating and breaking 250A capacity ,4 Pole MCCB, 50KA with thermomagnetic release and thermal spreader with suitable size cubical size box.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft/loose soil for foundation of poles, structures, stay rods, laying of underground cable etc complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers each not exceeding 25cm thick using soil complete all as directed.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed.

Supply and spreading of dry river sand in trenches/ transformer yard / two pole structure yard for cable protection complete all as directed by Engineer-in-Charge. Note:- Punned thickness only shall be measured for payment purpose.

Supplying and laying un-reinforced precast concrete cable cover LT cable Coverbut Class LV, Type 2, flat, size 250x 150mm x 40mm complete all as specified and directed

Supply installing, testing and commissioning of 2 TR capacity Split type air conditioner unit (Inverter type) BEE five star rated complete with drive motor, air cooled condenser with all accessories varied speed and dual rotary compressor, including fixing the outdoor unit with powder coated MS stand/PCC base and fixing of indoor unit on wall, providing and making interconnection, including refrigerant piping with nitryle rubber insulation and control cable from indoor to outdoor up to a distance of 3.0 mtrs, power cabling (max 3.0 mtrs from isolator/enclosure) to units, first charging non CFC/non HCFC refrigerant gas including cord less remote, PVC drain pipe of 25mm dia for connecting drain lines from indoor unit to maximum of 3.0 mtrs to nearest drain points complete all as specified and as directed. Make-Bluestar/LG/Voltas/Hitachi.

Supply installing, testing and commissioning of 1.5 TR capacity Split type air conditioner unit (Inverter type) BEE five star rated complete with drive motor, air cooled condenser with all accessories varied speed and dual rotary compressor, including fixing the outdoor unit with powder coated MS stand/PCC base and fixing of indoor unit on wall, providing and making interconnection, including refrigerant piping with nitryle rubber insulation and control cable from indoor to outdoor up to a distance of 3.0 mtrs, power cabling (max 3.0 mtrs from isolator/enclosure) to units, first charging non CFC/non HCFC refrigerant gas including cord less remote, PVC drain pipe of 25mm dia for connecting drain lines from indoor unit to maximum of 3.0 mtrs to nearest drain points complete all as specified and as directed. Make- Bluestar/LG/Voltas/Hitachi.

Supply and fix Voltage stabilizer copper wound for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5KVA

Supply and fix Voltage stabilizer copper wound for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4KVA

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required for 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required

Cutting to existing steel tubing for alterations upto 50 mm GI tubing

Supply & Fixing in repair of Pipes galvanized, “Medium class”, supplied And laid complete including fittings 50 mm (2.0”) dia.

Supply & Fixing in repair of Pipes galvanized, “Medium class”, supplied And laid complete including fittings 40 mm (1.5”) dia.

Supply & Fixing in repair of Pipes galvanized, “Medium class”, supplied And laid complete including fittings 25 mm (1.0”) dia.

S&F in repair Cast copper alloy Stop Valve, 50 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

S&F in repair Cast copper alloy Stop Valve, 25 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

Supply & Fixing in repair Ball brass valves, 15 mm size high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed.

SUN LIGHT HOUSE

ELEVATORS MAINTENANCE ENGINEER WORKS

Venkat Sai Enterprises

sri vishnu enterprises

UNITY ENGINEERING TRADERS

WELDECOR

Anjana corporation

MVS ENTERPRISES