SPECIAL REPAIR IN BLDG NO T-05, PROVN OF TWO BOREWELL AND OTHER SANCTIONED WORKS UNDER GE ALWAR

Amount

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including removing the domolisd material out side of defence land all as specifed and directed

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering .

Dismantling posts or struts purlins/rafter (wood, steel or R.C.C) any section, including taking out embedded Concrete, brick work,ground masonry etc and making good disturbed ground provided all as specified.

Dismantling of wall and ceiling boards (fibre pulp, insulation etc) or insulation boards/slabs

Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Demolition of reinforcement cement Concrete in Roof, floors (Other than ground floors), beams, staircase, landing, chajjas and similar suspended work complete all as directed.

M&L fly ash brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L fly ash brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

S&F for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) including distance pieces, cleats etc, confirming to Fe 410-W(Gde-E- 250)quality-A

S&F for steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240.

M&L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws as specified

M&L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws as specified

S&F for 9mm thick of size 600x600mm HSPC (high pressure Steam Cured) Pre-primetered self embossed, textured designer board to be fixed & including make Armstrong GI based powder coated snap grid/section size 600mmx600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper with preparation of sufaces etc complete all as specified.

M&L for Providing cement concrete as in coping PCC 1:2:4 Type B-0 using 12.5mm graded aggregate , with & including necessary form work Complete all as specified and as directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slab n.exc 200mm thick complete all as specified.

M&L for reinforced cement concrete type B1 (1:2:4) nominal mix using 20 mm graded broken stone aggregate as in beams/bands supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specifed and directed.

S&F Mild Steel TMT round bars 10 mm dia and over, cut to length, bent to shape required, including cranking , binding spirally for hooping end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per item No. 19.00 above but 6mm dia to 8 mm dia.

M&L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as under floor tiles finished the surface even and fair complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22" x 22" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 15mm thick cement screed bed in cement mortar 1:6 including rubbing and mirror polishing complete all as specified and as directed.

M&L for kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, rounding outer edges, rubbing and mirror polishing complete all as specified and as directed.

M&L for rubbing and polishing to exiting kota stone flooring including skirting/ riser to achive mirror finish all as directed.

M&L for hard core (broken stone or boulders) of gauge n. exc. 63 mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 50mm thick Cement Concrete type D 2 (1:4:8) using 40 MM graded stone aggregate as in sub bases, sub floors etc omplete all as specified and directed

M&L for rubber moulded concrete colour tiles with grey cement pigment of size 300 mm x 300 m x 22-25 mm thick laid over and including 20 mm thick cement mortar screed in CM 1:6 as in floors complete all as specified and directed.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4..00 Sqm each.

Taking down Chowkhats or frame with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each.

S&F Mild steel Framed work such as grills, gratings, etc using angle Iron, flat Iron, round bars, with end of bars shouldered and or rivetted or forged into spikes framed guard bars barred into iron doors ,walkways railing framework amd similler work confiming to Fe 290 ,GDE E-165 all as specified and directed.

S&F 35mm thick, factory made panelled door shutter (two panel), plain, framed with 2nd class hard wood lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS-1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S&F 35mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc (without sash bars) fitted with cut and mitred securing beads for securing glass etc complete as specified and directed sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F factory made steel windows, box type, any size (XW2) M/F) double shutter, one openable shutter with glazing bars and other openable shutter without glazing bars, fabricated with members of standard size as shown on drawings including frames, complete all as specified and directed. (Note :- The quoted rates shall be deemed of lugs and FI required for supply & fixing wire cloth, sheet Glass, Grills, iron mongry and guard bars as shown on drg and applying two coats of synthetic enamel paint over a coat of red oxide primer).

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete.

S&F butt hinges, cold rolled mild steel , 100mm medium weight and fixed all as directed.

S&F butt hinges, cold rolled mild steel , 75mm medium weight and fixed all as directed.

S&F butt hinges, cold rolled mild steel , 50mm medium weight and fixed all as directed.

S&F for Mild steel barrel tower bolts 200mm, stove enamelledblack, with bright boltand fixed as directed.

S&F for Mild steel barrel tower bolts 150mm, stove enamelledblack, with bright boltand fixed as directed.

S&F for Mild steel pressed handles 150 mm, ovaltype, stove enamelled black

S&F Mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia, 300mm leng, with and including a minimum of 6 bolts and nut, four on bolt plate and two on staple plate and fixed

S&F door spring with 300mm mild steel rat rail rod pattern of standard quality including roller and roller plate complete Helical spring)

S&F in repair for harrison rails 19/20mm thick, anodised aluminium alloy powder coated with fixing brackets, stops, rollers etc. compete all as specified as directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of stone masonry/brick masonry, or concrete surfaces, finished with even and smooth complete all as specified and directed.

M&L rendering 15mm thick internal surfaces in cement mortar 1:6 on fair faces of stone masonry or concrete surfaces finished even and fair without using extra cement all as specified and as directed.

M&L rendering 5mm on brick work or concrete surfaces as in ceiling in CM 1:3 and finished smooth and even without using extra cement all as specified and as directed.

M&L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed.

M&L for two coats of synthetic enamel paint on old steel surfaces of any description over 10cm width or girth including preparation.

M&L preparing new plastered surfaces of walls and applying two coat of oil bound distemper on decorated surfaces of walls including 2mm thick wall care putty in two layers complete all as directed.

M&L preparing new plastered surfaces of walls and applying two coats of cement paint over a coat of water primer complete as specified and directed.

M&L for preparation of old surfaces by washing rubbing down and stopping of plastered surfaces and applying two coats of Cement based paint white or tined on walls including cornices etc complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc

M&L anti-termite treatment to the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & as directed.

M&L anti-termite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified & as directed.

M&L anti-termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified & as directed.

M&L anti-termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & as directed.

M&L 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork. Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound (ISI marked).

M&L preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

M&L preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified.

M&L for 25 thick cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring complete.

M&L coloured non skid ceramic tiles 300mm x 300mm x 7mm thick as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 450mm x 350mm x 7mm thick Ist quality on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for screed laid 10mm thick in CM 1:4 with water proofing compound over green concrete surface finished even and smooth without using extra lime or cement complete all as specified and directed by Engr-in-Charge.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L for formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F as in repairs Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F 15mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F vitreous china wash hand basin, white, flat back of size 580mm x 450mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

S&F 15mm bore Stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) all as directed. Make : Prayag, Polytuf, Jindal

S&F vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specifie

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) all as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

S&F PVC (SWR) floor trap dia of outlet 125/110mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

S&F 110mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

S&F salt glazed stone ware drain pipes of 100mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

Cutting and inserting tee, L bow, bend/collar and tapping the connection from the existing 50mm GI tubing line for taking branch connections including tapping accessories complete all as directed.

M&L galvanised steel water tubing light grade of 40mm bore with & including all fittings complete laid in trenches. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

Taking down carefully, copper / aluminium unserviceable /perished point wiring any type for light/ fan/ socket or power complete including fittings such as switches, ceiling roses, pendant holders, lamp holders, bracket holders, regulators sockets, light fittings etc, and making good to disturbed surfaces of wall/floor/ceiling etc, complete, all as specified and directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS and including wooden boxes fixed on wall with and including 3mm thick phenolic laminated sheet top cover for mounting switches, sockets, fan regulators etc complete all as specified.

All as per serial item No. 104.00 here-in-before but for one fan point controlled byone switch and regulator.

All as per serial item No. 104.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No. 104.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No. 104.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 3 pin(with 2pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5/6 & 15/16 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface Bakelite 65x50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube 6000K of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make :- Havells Cat Part No LHEXBHP71NW018 or equivalent of Philips/ Crompton Greaves/Bajaj/Wipro as approved by GE

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F Adore LED lamp of 9/10 watt including taking down old u/s CFL lamp complete all as specified& directed. Make :- Havells Cat Part No LHLDERHEML8X010 or equivalent of Philips / Crompton Greaves/Wipro/Bajaj as approved by GE

S&F LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make :- C&S Cat Part No LTESS20WLED or equivalent of Crompton Greaves / Wipro as approved by GE

S&F stepped type electronic fan regulator, flush type and connecting up, ISI marked, 240 Volts.

S&F sheet metal enclosures, double door type, suitable for fixing MCB,s, TPN with 200 Amps rated bus bar, 4 way, 415 volts complete all as specified and directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 63 Amps, Triple pole & neutral, 230 Volts complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 60x45x5 cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawlplug(4 Nos), complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30x25x5 cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawlplug(4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 35 sqmm 3.5 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth; for foundation, etc or for laying of cables, pipes etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified& directed.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

M&L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (Tibba sand) and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Supply & install Hi wall split unit indoor / outdoor complete electric driven single phase of capacity 2.00 TR (5 Star rating & EER 3.2 ) with cordless remote control unit and with in built air ioniser and plasma filter for better indoor air quality and connecting up complete all as per manufacturer’s instructions & as directed. Note :- (i) Cost of cutting chases/cutting holes etc in walls/floors including making good in cement mortar 1:4 and other necessary arrangement for fixing indoor & outdoor unit & other minor extras shall be deemed included in quoted rate of this item.

Supply, laying, jointing and testing XLPE insulated screened meter PVC bedded, galvanized steel strip or armoured, heavy duty electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 16 sq mm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed.

M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cables, drawn through & including suitable size of heavy duty PVC conduit ISI marked not less than 32mm dia (external) with wall thickness not less than 1.8mm & conduit fittings/accessories, fixed on surfaces of wall/ceiling complete all as specified and directed. Note:- 02 runs of 6 sqmm size, 01 run of 6 sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose.

S&F sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 4 way, 240 volts complete all as specified and directed.

S&F MCB 40 Amps, single pole & neutral, 240 Volts, 10KA rupturing complete all as specified and directed.

S&F MCB 32 Amps, single pole, 240 Volts, 10KA rupturing complete all as specified and directed.

S&F of high density polyethlene pipes (HDPE) of pressure rating 6 kgf/sqcm of 25mm bore with & including all fittings complete concealed / surfaced to the wall / floor etc for drain otu condensed water complete all as specified and directed. Note :- (i) Cost of cutting chases/cutting holes etc in walls/floors including making good in cement mortar 1:4 shall be deemed included in quoted rate of this item.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 230 Volt, complete all as specified and directed.

S&F Voltage Stabilizer of capacity 5 KVA for automatic operation, Single Phase, naturally air cooled, indoor type, designed for input variation between 170 Volt to 250 Volt and with output voltage stabilized at 230 Volt with accuracy of ± 2.5% and connecting up all as per manufacturer’s instructions & as directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Boring of holes under road, pavement, hard standing by trench less technology using ultra sound technique & necessary machine including suitable HDPE pipe of 80mm outer dia for 0.4 mpa working pressure complete all as specified and as directed.

Supply, Installation, commissioning and testing of High Intensity type LED based street light of 90 watts rating new generation energy saving and environmental friendly long life versatile, IP 66 roadway luminair, enclosed in high grade aluminum pressure die-cast housing with heat resistant toughened flat glass suitably gasketed all including high power LEDs as light source complete all as specified & directed. Note :- (i) The contractor should give warranty for the complete fitting including its LEDs, Lens, Driver, SPD, Protection devices and all Electric/Electronics connected parts for minimum 3 (Three) years and Contractor should submit manufacturers warranty certificate for fittings for minimum 3 (Three) years in writting. (ii) The contractor should submit latest LM-79 & LM-80 reports (Test certificate) for street light fittings from NABL accredited Lab. The quoted rates shall deemed to be inclusive for above stipulations. (iii) All LED light/luminaries must meet the provision laid down in relevant ISs. (iv) LED light fittings is required to be fixed on steel tubular poles/PCC poles or swan neck swaged tubular poles with all T&P and accessories etc complete including making connection , testing etc complete. No extra payment shall be admissible on these account.

S&F Junction box made out of one piece moulded SMC IP 65 protection of size 300x200x100mm with hinged door and locking arrangement & including aluminium bus bar of rating 100 Amps thre phase and neutral, including one No MCB SP 6 Amps and cable entry from bottom, fixing on pole with MS flat of size 25x3mm with nut bolts, front openable complete all as specified and as directed.

S&F mounting bracket (suitable for fixing / holding street / security light fittings) fabricated out of GI tubing 40 mm bore light grade not less than 1.5m long made to shape at required angle & including 2 Nos flat iron clamp 50x6mm to be tightened with 4 Nos nut & bolts, washers of suitable size mounted on pole complete all as specified and directed.

Supplying, transporting to site errecting and fixing in position Steel tubular swaged pole, 9 metres long, type 410 SP-31, complete with cast iron base plate, pole cap, finial taper plug, bolts, nuts, washers etc including painting with two coats of aluminium paint over one coat of red oxide primer including 3 nos band/straps in red post office box colour (300mm wide EACH) using fluorescent paint commencing at a distance 300mm from padestal of pole and marking pole nos with black synthetic enameled paint including tarring one coat on steel surface embedded in concrete complete all as specified and directed. Note:- Excavation and earth work, PCC etc shall be measured and paid separately under respective items.

M&L for PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate as in coping padestal of poles etc including weathring, slightly rounded or chambered angle and throating, necessary form work finishing all exposed faces of concrete even and smooth using extra cement complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation of poles/ struts/ stay assembly etc complete all as specified and directed.

M&L Galvanised iron tubing, 40mm bore light grade, ISI marked, including fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete.

S&F PVC insulated & sheathed 3 core stranded copper conductor 2.5 Sqmm cable 1100 Volts grade (ISI marked) from SMC box to street light fitting complete all as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

M/s Laxmi Associate

M/s PATEL CONSTRUCTION COMPANY

M/s Laxmi Enterprises