ADDN/ ALTN/ OF TOILETS AT WORK PLACES FOR AGNIVEER VAYU (WOMEN) AT AF STN MEMAURA

Amount

Excavation in trenches, in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundation etc.and getting out complete all as specified and directed.

Returning, filling, including spreading, levelling, watering and well ramming in layers not exe 25cm complete all as specified and directed

Removing excavated material n exe 50m and depositing where directed at a level n.exe 1.5m above the starting point complete all as specified and directed

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation,filling and mass concrete complete all as specified and directed.

M & L for damp proof course PCC 1:2:4 type B-0 grade 40mm thick over masonry wall horizontal or vertical surfaces including necessary formwork over polythene film of 50 micron over a coat of blow bitumen of Grade 85/25 conforming to IS-702 @ 1.5 Kg/Sqm and blended with clean dry sand @ 0.05 cum per Sqm

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed

M&L for fair finished flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc, also splays between floors and beams, etc complete all as specified and directed

M&L for fair finished form work to edges of concrete for roof exc 10cm but n exc 20cm wide all as specified and directed

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, loandings and similar work; not exceeding 200mm thick (Horizontal or sloping)all as specified and directed

M&L for RCC M-25 (desing mix) in beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

M&L for RCC M-25 (desing mix) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed

M&L for mild deformed TMT steel bars 10mm dia and over, cut to lenght, bent to hasp required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and directed

Ditto, as per item No 12 but 5mm and over upto and including 10mm dia in stirrups, spacers and binders

M & L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore broken bricks of gauge n exc 63mm, deposited, spread and lvelled in layers n. exc 15cm thick watered and rammed to a true surface

M&L for PCC type D-2, 1:4:8 (40mm graded aggregate) 100mm thick in sub floors, sub bases floors as specified and directed

M&L for PCC 1:2:4,type B-1(20mm graded aggregate) 25mm thick in sub floors, sub bases floors as specified and directed

M/L 15mm thick rendering in CM 1:4 with water proofing compound on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed.(Note- WPC Qty should be measured and paid to separately.)

Supply only water proofing compound complete all as specified and directed.

Material & labour for rendering 5mm thick in cm 1:3 as in ceiling finished even & fair faces complete all as specified and directed .

M&L for rendering 15 mm thick on other than fair faces of brick work in cement 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M & L for prepration of new plastered or unplastered surfaces of wall applying two coats of oil bound distemper after applying primer over 3.00mm thick putty complete all as specified and directed.

Material & labour for preparing new plastered surfaces of ceiling and applying two coats of OBD complete all as specified and directed .

M &L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over one coat of 1.00mm thick putty and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc all as specified and directed.

S&F non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 Sqm but n exc 0.11 Sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed bed or bedding layer of mortar in CM 1:6 complete all as specified and as directed.

M & L galzed ceramic coloured tiles 450 x 350 x 6 to 7 mm/ 450x300x6 to 7mm thick on walls etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces including 10mm thick rendering in CM 1:4 complete all as specified and as directed. etc complete all as specified and directed.

S & F factory made 100% solid wood polymer composite (WPC) Door frame made from wood polymer composite (single extruded process) material with standard density 780kg/m3 & manufactured as per ISO 9001-2015 certified company, all as per specifications, drawings as directed by Engr-in-Charge.

S & F factory made solid WPC door shutter 30mm thick solid plain of required size comprising of virgin polymer of K value 58-60(Suspension grade), calcium carbonate and natural fibres(wood powder/rice husk/wheat husk) and non toxic additives made from Extrusion process WPC foam sheet single Extruded (inner) with standard density approx 550 kg/cum manufactured as per ISO E9001-2015 certified company having good screw holding capacity (screw withdrawl strength of 2000N Face & 1000N Edge, minimum compressive strength 50N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof, Fire retardant and fixing with S.S butt hinges of required size with necessary full body threaded star headed counter sunk S.S. screws all as per direction of Engineer-in- Charge.

S & F for extruded aluminium alloy hinges 100 mm fixed to door frame complete all as specified and directed.

S & F for 125 mm long extruded aluminium alloy handles, fabricated type, of approved design fixed complete all as spefied and directed.

S & F of 200 mm long (Length of bolt) aluminium anodised sliding door bolts with hasp staple bolt type and fixing clips of sheet of extruded section and fixed complete all as specified and directed.

S & F of 150 mm long (Length of bolt) aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors frames, windows ventilators and partitions (Fixed portions) with extruded built up standard tubular section of approved make conforming to IS 733 and 15:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at i.e junctions, Le at top, bottom. and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight. mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

S & F of stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staple all as specified and directed.

S&F Aluminium anodised grill( anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to existing window frame with CP brass/stainless steel screws @200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around opening all complete all as specified and directed.

Supplying and fixing 5.0 mm thick figured glass ordinary quality, pinhead, n-exceeding 0.50 Sqm in each pane fixed to aluminium frame work with necessary glazing clips/rubber packing/gasket, screws etc complete all as specified and as directed by Engineer-in-Charge.

S&F 250 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good,cutting not exc 10 cm girth complete all as specified & directed.

Supply & laying of CPVC 16mm pipes SDR13.5 pipes & plain CPVC SDR 11 fittings in floors/walls/ceilingss for 16 mm bore complete all as specified and directed .

All as per item No.39 above but 20 mm bore pipe.

S & F tank adaptor of 20mm diameter for CPVC pipe complete all as specified and directed.

S&F 20 mm dia CPVC ball valves with plastic wheel head screwed both ends for CPVC pipe complete all as specified & directed.

Supply & fix 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule complete all as specified and directed .

Supply & fix 15 mm dia angle stop cock fancy type chromium plated CP screwed down high pressure with flench screwed to connect with PVC connections both ends for iron or for union complete all as specified and directed.

Supply & fix vitreous china wash hand basin, white size 550x400 mm including brackets, CP waste coupling & PVC waste pipe of 32 mm dia of LDPE 800mm long complete all as specified and directed.

S & F PVC connection with CP brass nuts 450 mm long all as specified and directed .

S&F 15mm bore pillar taps brass chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe, fixed in repairs complete all as specified & directed.

Supply & fix bib taps brass chromium plated fancy type 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed .

S&F PVC (SWR) 100mm diameter floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M & L for 100mm pipe Cutting into existing manholes for connecting new drains,making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

S&F chromium plated towel rail 600 mm long, 20mm dia of a approved quality, complete all as specified & directed.

S&F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F ABS body health faucet, chromium plated with 1.25 mtrs pipe of approved make and quality with wall hook complete all as sepecified and directed.

S&F 75 mm bore PVC (SWR) pipe single socketed,in any length with rubber ring joints,including bend,socket laid in trench or in floors including connecting to existing drain complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipe single socketed,in any length with rubber ring joints ,including bend,socket laid in trench or in floors and complete all as specified and directed.

M & L for Providing precast cement concrete type B-1 1:2:4 (using 20mm graded concrete) set in cement mortar 1:4 in landings, cover slabs (for man holes,drain cover etc.) chullah hoods, chajjas, water troughs,mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channel and drain complete all as specified and directed.

M&L PCC type B-1,1:2:4 (20mm graded stone aggregate) as in coping, side kerbs, mud stops etc complete all as specified and directed.

S&F vitreous china wash down water closet pan pedestal pattern, white including PVC seat cover excluding flushing cistern and flush pipe complete all as specified and directed

S&F PVC low level flushing cistern, white of capacity 10 litre ISI marked complete with inlet ball valve , and handle including bracket complete all as specified.

Material & labour for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection/Path paving surface finished even and smooth without using extra cement complete all as specified and directed .

S & F flush pipe of polyethylene of high desnsity or low density for low level cistern complete all as specified and directed.

M & L for applying Smart Care Damp Proof Ultra fibre reinforced elastometric liquid applied water proofing membrane as in roof treatment @ 1 Litre per 10 Sqft inclusive of all three coats as per following application process: - (a) Providing average 15mm thick plaster bed in CM(1:3) mixed with water proofing compound. (b) Prepare the surface by cleaning with high pressure water jet / wire brushes to ensure that it is free of dust, oil, grease, grime and loose particles. (c) Damaged portion if any to be repaired before application of roof treatment as per manufacturer's instructions. (d) Applying self priming coat of Smart Care Damp Proof Ultra duly dialuted with water in 3:1 ratio by volume. Allow the primed surface to dry for at least 3-4 hours prior to application of subsequent coat. (e) Applying 2 perpendicular coats of Smart Care Damp Proof Ultra without any dialution to achieve a forced system coverage. Allow it to dry for at least 4-6 hours between two coats. NOTE: - WORK SHALL BE CARRIED OUT BY THE AUTHORISED APPLICATORS OF THE MANUFACTURER IN CLOSE SUPERVISION OF EXECUTIVE STAFF UPTO ENGINEER-IN-CHARGE LEVEL. MAKE- ASIAN PAINTS, STP LTD OR EQUIVALENT.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises complete all as specified and directed .

Demolition of cement Concrete in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and directed

Taking down cement or cement lime plaster from brick or stone walls and ceiling, chajjas etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down of chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore pipe and removing from site & including supply & fix tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors or walls with cutting chases and making good to facings and pointing in cement mortar 1:3 to ends or edges for 15 mm bore complete all as specified and directed .

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M & L for half brick wall built in cement mortar 1:4 with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in complete all as specified and directed.

S & F in repairs Vitreous China bowl urinal, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including flush pipe and including pvc connection & 32mm diam LDPE pipe 800mm long complete all as specified and directed.

S&F in repair Vitreous China wash hand basin white flat back size 550x400mm including brackets and including pvc connection and 32mm dia waste coupling with LDPE pipe 800mm long complete all as specified and directed.

M/L for machine cut 20mm thick Granite black /coloured and fixed as partition wall of urinals/wash hand basin platform with 12mm thick cement mortar (1:3) and the like with grey cement slurry and pointed in white cement with admixture of pigment to match including cutting, polishing and necessary bull nozing/ full round grinding complete all as specified & directed .

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base of floor etc complete all as specified

M & L for sand filling in floors, 50 mm thick, spread levelled and rammed including watering and consolidating complete all as specified.

S&F for 60MM thick machine pressed precast concrete interlocking paver block coloured reflective type rubber moulded any shape and size with grey cement and pigment confirming to IS 15658-2006 of M-40 grade complete all as specified and as directed.

Supply and fixing gun metal gate valve with iron wheel head screwed both end suitable for 20mm bore pipe, ISI marked, complete all as specified and as directed.

Supply & fixing 20 mm bore galvanised steel tubing medium grade, ISI marked including necessary fittings complete all as specified and as directed.

Supply & fixing 25 mm bore galvanised steel tubing medium grade, ISI marked including necessary fittings complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation etc or for laying pipe lines and getting out as in soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layer not exceeding 25 cm in hard/dense soil, complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Cutting CI/GI pipes of size up to 80 mm and redusing to required length before layingin position for insertion of new tees,branch etc.

Taking down copper/aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE (I) Memaura or for fixing new position complete all as specified and directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed PVC conduit of size 20/25mm ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

S & F for switch piano type single pole 5 amp, 230 Volts complete all as specified and directed.

S & F for socket outlet 2-in-1, 5 pin, 5 amp, 230 Volts complete all as specified and directed.

S & F for ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete.

S & F for sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Refixing of existing serviceable tube light any size removing from old position after disconnecting electrical connection from ceiling rose without disturbing any floor surfaces complete all as directed by engr-in-charge.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S & F for wall mounted LED tube light fitting 10 watts batten for mirror type surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge.

S & F for exhaust fan made of styurdy engineering plastic body heavy duty single phase 250 mm sweep,50 HZ,RPM 1200 ,240 Volts, AC with and including louvers, mounting rings, MS rag bolt, washers etc and connecting from ceiling rose / connector with and including suitable size flexible copper conductor PVC insulated sheathed chord and duly making holes complete all as specified and directed at site.

Refixing of existing serviceable Exhaust fan any size removing from old position after disconnecting electrical connection from ceiling rose without disturbing any wall/floor surfaces complete all as directed by engr-in-charge.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note:- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size complete all as specified and directed

(a) 2 core x 10 Sqmm

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation etc or for laying pipe lines and getting out as in Soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layer not exceeding 25 cm in hard/dense soil, complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Burnt bricks sub class 'B' laid flat dry across the cable for cable protection all as specified and directed.

Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. Note: (i) Consolidated / Punned sand shall be considered for purpose of payment (ii) Sand shall be same as specified for plastering work.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for including disposal of unserviceable material complete all as specified and as directed.

M & L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate for to support the pipe line etc, including necessary form work complete all as specified and directed.

Rakesh Traders (BID ID -3443677)

Shri Siddhi Vinayak Builders (BID ID -3444477)

M/S IQRA CONSTRUCTION (BID ID -3444341)

M/s Ramesh Chandra (BID ID -3445154)