Construction of Mortuary for civil hospital at Salooni Distt Chamba HP

Amount

Cutting in earth work in all heights/depths in all kinds of soil such as kankar, moorum, single and decomposed or soft rock, hard rock i.e. their intermediate classifications and chiselling/wedging out of rock where blasting is prohibited including saturated soils & filling embankments etc.where necessary & disposal of exacavated unserviceable material in all leads and lifts including through mechnically transporation, the disposal of unserviceable material will be done on aproved dumping site. Any damage to the private/public property during execution will be restored by the contractor what so ever the nature of the same may be. The serviceable material will be stacked in specified dimensions in all leads & lifts as per the direction of the Engineer-in-charge

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work and chiselling / wedging out of hard or soft rock where blasting prohibited up to all depths stacking the excavated soil not more than 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Filling in plinth with sand under floors including watering , ramming , consolidating and dressing complete including cost of sand including carriage of material in all leads & lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping, etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of material in all leads & lifts.

(a) Foundation, footing bases of columns etc. and mass concrete.

(b) Flat surfaces such as soffits of suspended floors, roofs inluding inclined surfaces up to any degree, landings and the like:(i) Floors, etc. upto 200 mm in thickness.

© Beams, cantilevers, girders and lintels sides and soffits of beams, small ends of beams,beam haunching, cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth.

(d) Edges of slabs and breaks in floors and walls under 20 cm. wide.

(e) Cornices and mouldings.

(f)Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete on slab and floor excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 :4 : 8 (1 cement:4 sand:8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete work 1:2:4 (1 Cement:2 Sand:4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of material in all leads & lifts.

(a)Foundations, footings, bases of column and the like and mass concrete.

(b) Suspended floor, roofs, landings, shelves and their support, balconies, beams, girders, bressumers and cantilevers in all heights.

(c) Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses, plinth and string courses etc. from top of foundation in all heights.

Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement including carriage of material in all leads & lifts. (a) Mouldings as in cornices windows sills etc. exceeding 15cm in girth

Providing Tor steel/TMTsteel reinforcement for R.C.C. work including bending,binding and placing in position complete including cost of binding wire including carriage of material in all leads & lifts.

Brick work using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads & lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure above plinth level upto all floor level in cement mortar 1:6 (1 cement : 6 sand) including carriage of material in all leads & lifts.

Half brick masonry using 2nd class common burnt clay building bricks in super-structure above plinth level upto all floor level in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads & lifts.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth with cement mortar 1:6 (1 cement:6 sand) including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level inincluding carriage of material in all leads & lifts.

Stone soling properly hand-packed filling interstices with spalls and consolidating with hand rammer including spreading watering etc.complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour) including carriage of material in all leads & lifts

Providing and laying cement concrete 1:5:10 (1cement :5sand :10 graded stone aggregate 40mm. nominal size) with 15 % plum and curing complete including cost of form work in retaining walls / Breast walls, the size of plums shall usually be 150mm. to 300mm. as per H.P.P.W.D.Specification including carriage of material in all leads & lifts.

Providing weep holes in brick masonry /stone masonry/ plain reinforced concrete abutment , wing wall , return wall with 100 mm dia pvc pipe extending through the full with of the structure with slop of 1(V):20 (H) towards drawing face complete as per drawing and technical specifications clause 614,1204,3.7 including carriage of materials in all leads and lifts.

Stone filling behind retaining walls including carriage of material in all leads & lifts.

Providing and fixing Single rebate angle iron doors, windows, clerestory windows frames manufactured from structural steel iron section of angle 40 x 40 x 6mm thickness welded with 50 x 6 mm welded with 6mm thick flat iron including hinges, jambs, lock jambs, mild steel 50 x 25mm welded or rigidly fixed by mechanical means lugs with split end tails to each jambs including steel butt hinges 3.5 mm thick with provision with locking arrangement and shock obserber as specified and applying a coat of approved steel priming after pretreatment of the surface as directed by the Engineer -in-Charge including carriage of material in all leads & lifts .

Providing and fixing double rebate angle iron doors, windows, clerestory windows frames manufactured from structural steel iron section of angle 40 x 40 x 6mm thickness welded with 50 x 6 mm welded with 6mm thick flat iron including hinges, jambs, lock jambs, mild steel 50 x 25mm welded or rigidly fixed by mechanical means lugs with split end tails to each jambs including steel butt hinges 3.5 mm thick with provision with locking arrangement and shock obserber as specified and applying a coat of approved steel priming after pretreatment of the surface as directed by the Engineer -in-Charge including carriage of material in all leads & lifts .

Providing and fixing 40mm thick flush door shutters decorative type core of block board construction with frames of first class hard wood and well matched first class indian teak ply veneering with vertical grains or cross bends and face vencering on both faces of shutter factory made including carriage of material in all leads & lifts.

Providing and fixing 40mm thick single/double leaf glazed window shutter made of 2nd class doedar wood having style and top rail and bottom rail 75mm width and chamferred edged moulding 20X12mm for glass panes complete including bright finished balck enamelled iron hinges with necessary screws including carriage of material in all leads and lifts.

Providing and fixing 40 mm thick 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of material in all leads & lifts.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. With M.S. Flats, square or round bars with round headed bolts and nuts or by screws. including carriage of material in all leads & lifts.(a) Plain grill.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing toframe with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x 10x 15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size)including carriage of material in all leads & lifts.

Providing and fixing anodized aluminium sliding door bolt annodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including carriage of material in all leads & lifts.(a)300x16mm

Providing and fixing aluminium tower bolt (barrel type) annodized to transparent or dyed to required shade and colour with screws etc. complete including carriage of material in all leads & lifts.(a)200x 10 mm

Providing and fixing aluminium handles annodized transparent or dyed to required colour or shade with necessary screws including carriage of material in all leads & lifts. (a)125 mm

Providing and fixing oxidized M.S. hooks and eyes including carriage of material in all leads & lifts. (a) 150 mm.

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads & lifts.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of material in all leads & lifts.

Providing and laying granite stone in flooring 20mm (average thickness base of cement mortar 1:3 (1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material in all leads & lifts.

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 32 mm thick cement concrete 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 10 mm and down gauge) and top layer 8 mm thick marble chips of required sizes laid in cement marble powder mix 3:1 (3 cement:1 marble powder by weight) in propontion of 4:7(4 cement marble powder mixed : 7 marble chips by volume) including carriage of material in all leads & lifts.(a) Medium shade pigment with approximate 50% white cement and 50% ordinary cement (in top layer only)

Providing and fixing 10mm thick antiskid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent (any size and colour) 10mm thick manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1cement: 3sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including cost of tiles where required to be cut including carriage of material in all leads & lifts.

Providing and laying Duro stone vetrified tiles (any size ) 10mm thick in grey /coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including cost of tiles where required to be cut including carriage of material in all leads & lifts.

Providing and laying Duro stone vetrified tiles (any size ) 8mm thick in grey /coloured or of approved shade in skirting, riser of step and dado on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including cost of tiles where required to be cut including carriage of material in all leads & lifts.

Kota stone slab 25 mm thick flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of material in all leads & lifts.

40 mm thick cement concrete flooring 1:2:4 (1cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement including carriage of material in all leads & lifts.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for including carriage of material in all leads & lifts.(a) 60mm thick inter locking blocks.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of material in all leads & lifts.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including carriage of material in all leads & lifts.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I.limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge. including carriage of material in all leads & lifts.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board /facia /soffits /ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of material in all leads & lifts.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material in all leads & lifts. (a) In beams joists channels ,angles , tee ,flats with onnecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

(b) In gratings framed guard bars,ladders,railling,brackets and similar works including carriage of material in all leads & lifts.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead, red oxide/ zinc oxide chrome.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of material in all leads & lifts: Enamel paint other than white/ white paint.

Painting two coats (excluding priming coat) on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt, dust and other foreign matter and sand papering as required with Enamel paint other than white including carriage of material in all leads & lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering and knotting including carriage of material in all leads & lifts. Ready mixed paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint, brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping : Enamel paint other than white/ white paint.

15 mm cement plaster in single coat on fair side of brick / concrete/ stone walls for interior/ exterior plastering upto all heights including arises, Internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm in girth & finished even & smooth in cement mortar 1:6 ( 1 cement : 6 sand) including carriage of material in all leads & lifts.

20 mm cement plaster in single coat on rough side of brick / stone masonry for interior/ exterior plastering upto all heights including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm in girth and finished even & smooth in cement mortar1:6 (1cement : 6 sand) including carriage of material in all leads & lifts.

20mm cement plaster with cement mortar 1:4 (1 Cement :4 sand) in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads & lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after throughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer including carriage of material in all leads & lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equalized on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etc. including and paper smooth complete including carriage of material in all leads & lifts.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.including carriage of material in all leads & lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) including carriage of material in all leads & lifts.

Providing under layer for plinth protection of 75 mm thick (un consolidated) bed of dry bricks / stone aggregate 40 mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads & lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads & lifts.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.90 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.50 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011(Board with BIS certification marks)

Supplying and fixing plain glass 4mm thick glass pans with 2nd class deodar wood chamfered moulding 38x12mm along the pannels with nails complete in all respects including carriage of material in all lead & lift.

Providing and fixing to wall ceiling and floor Polyethylene – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe confirming to IS 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to with stand temperature up to 80 degree C, including all special fittings composite materials (Engineering plastic blend brass insertes where ever required) e.g. elbows, tees, reducers, couplers and connectors etc. with clamp at one metre spacing.This includes testing of joints complete as per direction of Engineer-In-Charge including carriage of material in all leads and lifts. (a) 1216 (16 mm O.D. pipe)

(b) 1620 (20 mm O.D. pipe)

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and fixing polythene water storage tank for storage of water up to all heights keeping water hygenic and safe for drinking etc.moulded to seamless perfection from FDA approved grades of polythene (LDPE / HDDE / CIDPE) confirming to BIS-12701-1989 with 40 mm nominal bore galvanised steel scoure tube with fittings 25mm nominal bore galvanised mild steel over flow tube with fitting & mosquito proof coupling of approved municipal design 15mm nominal bore ball valve and as per direction of Engineer-in- charge.(i) 1000 liters capacity

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive,cost of cutting and making good the wall and floors etc, complete including carriage of material in all leads and lifts.(a) 110 x 75 mm

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. comlete including carriage of material in all leads and lifts.

(a)90mm dia.

(b) 110mm dia.

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

(a)90mm dia.

(b)110mm dia.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. completeincluding carriage of material in all leads and lifts. (a) 110mm dia.

Providing and fixing PVC door bend with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

(a)90mm dia.

(b)110mm dia.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

(a)90mm dia.

(b) 110mm dia.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

(a)90mm dia.

(b) 110mm dia.

Providing and fixing PVC cowl (confirming to B.I.S specification) including carriage of material in all leads and lifts.(a) 110 mm dia

Providing and fixing to wall ceiling and floor high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet,outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of material in all leads and lifts.

Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material in all leads and lifts.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.(a) 90 mm dia.

(b) 110 mm dia.

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) including carriage of material in all leads and lifts. (a) Angle Indian Universal closet.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage of material in all leads and lifts. (a) SOLID TYPE:- white plastic seat and cover.

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. Or M.S. brackets painted white including cutting holes and making good the same but excluding fitting and (Confirming to B.I.S. specification) including carriage of material in all leads and lifts.(a)Flat back:-i) 630mmx450mm

Providing and fixing 32 mm dia C.P. Brass waste for wash basin or sink(Confirming to BIS specifications) including carriage of material in all leads and lifts.

Providing and fixing 32mm dia M.I. Union for wash basin or sink including carriage of material in all leads and lifts.

Providing and fixing 600mmx450mm bevelled edge mirror of superrior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brassscrews and washers including carriage of material in all leads and lifts and confirming to BIS specifications. (Atul, Modi Guard, Saint Gobains)

Providig and fixing C.P. brass towel rail complete C.P.brass brackets ( fixed to wooden plugswith C.P. brass screws , and (Confirming to BIS specifications) 600mm x20mm, including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden plugs with C.P. brass screws, and (Confirming to BIS specifications) including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing brass bib tap (Superior or heavy type) :-15 mm dia long body and (Confirming to BIS specifications) including carriage of material in all leads and lifts.

Providing and fixing C.P. brass pillar tap wih capstan head :-15 mm dia with Aerator, and (Confirming to BIS specifications) including carriage of material in all leads and lifts.

Providing and fixing C.P.brass angle valve 15 mm without nuts and pipe including carriage of material in all leads and lifts .(Confirming to B.I.S. specification).

Providing and fixing PVC connection pipe with brass unions including carriage of material in all leads and lifts.(a) 300/450 mm length (i) 15mm nominal bore.

Providing and fixing brass full way valve with wheel (Confirming to B.I.S specification) including carriage of material in all leads and lifts.

(a) 15mm nominal bore.

(b)20mm nominal bore.

Providing and fixing G.I./ M.I. union of the following sizes ( where not included in the item) including carriage of material in all leads and lifts.(Confirming to B.I.S. specification)

(a) 15mm nominal bore.

(b) 20mm nominal bore.

Providing and fixing C.P.brass concelled stop cocks 15 mm without nuts and pipe including carriage of material in all leads and lifts. confirming to B.I.S. specification.(ESS-ESS/CZAR/NOVA)

Providing and fixing stoneware gully trap grade"A" complete with C.I. grating. Brick masonary chamber in cement mortar 1:5 and water tight C.I. cover with frame of 300mmx300mm size (in side) the weight of cover to be not less than 4.53 kg and frame to be not less than 2.72kg. including carriage of material in all leads and lifts.(Confirming to B.I.S. specification) (a) Square Mouth Traps: i)100mmx100mm size P type.

Suppling and fixing 455 x 610 mm light duty rectangular cast iron cover with frame weight 38 kg (single seal pattern) including carriage of material in all leads and lifts.

Providing 200 mm wide cast iron Rungs with chequered or ribbed non slip surface including fixing in manholes with 200 mm x 200 mm x 100 mm cement concrete 1:3:6 (1Cement:3Sand:6graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts

Construction of soak pit 2.50 metre diametre 3.00 metre deep with 45x45cm dry brick masonry of class designation 75mm S.W. drain pipe 100mm diameter 1.80 metre long as per standard design with FPS including carriage of material in all leads and lifts.

Constructing man hole with RCC top slab in 1:2:4 mix (1cement:2sand: 4graded stone aggregate 20mm nominal size ) Foundation concrete 1:4:8 (1cement : 4sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3(1 cement:3 sand) finished with a floating coat of neat cement and including making channels in cement concrete 1:2:4 mix (1cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testng including carriage of materials in all leads and lifts.

(a) Inside size 800mm x 800mm and 500mm deep including S.F.R.C. frame and cover medium duty 500mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) .

(b) Inside size 1200mm x 900mm x1000mm deep including S.F.R.C. frame and cover medium duty 1000mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) .

naveen kumar