SPL REPAIR TO BLDG NO 10 E DILKUSHA COMMA SPL REPAIR TO BLDG NO P 10 AND PROVN OF 02 NOS TOILET BLOCK WITH ADDN ALTN TO BLDG NO P 8 UNDER GE WEST LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended works complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Dismantling of framed work of timber scantlings 40 sq cm and over in section, in any position complete all as specified and directed.

Dismantling of structural steel work including doors, gates, wind tie etc., but excluding framed trusses etc. complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Labour only for Earth (soil) filling under floors or in foundatoins including spreading, levelling in layers n. exc 25cm thick, watering and well ramming complete all as specified and directed. NOTE: Soil obtained from excavation shall be used.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for 40mm thick damp proof course in cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate, to horizontal or vertical surfaces with water proofing compound including necessary formwork complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in bed blocks, roof kerbs or mud stops, rounded or champhered on edges including necessary formwork complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basements slabs, under reamed piles and mass concrete and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in slab supported on wall, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and similar works complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished surface complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splay between floors and beams, etc. and similar works for rough finished surfaces complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F Anodized aluminium frame for doors, windows, ventilators with one or more rebates using 1.50mm thick aluminium section including joining cleat for fixing etc. complete all as specified and directed.

S&F 12mm thick toughned glass door shutters, side hung type with 02 nos 300mm long fancy type handle and one no mortice lock of size 100mm, 4 levers (vertical type), self closing device with rebates and fixed on floor door spring pivot including rubber packing complete all as specified and directed.

S&F anodized aluminium glazed/panelled partitions, fixed type, with sash bars, with aluminium section 38x65x1.50mm thick aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. and provn of 12mm thick prelaminated particle board and glazed with 5mm thick tinted glass complete all as specified and directed.

S&F anodized aluminium glazed window and ventilator shutters, side hung/ top hung type without sash bars, with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 01 no. 150mm long peg stays, 02 nos. 100mm long hinges type B-21, 01 no. 150mm long tower bolts and 01 no. 125mm long handles including glazed with 5mm thick tinted glass or wire meshed with stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

S&F anodized aluminium glazed window shutters, sliding type, three track (two of glass and one of stainless steel wire cloth) without sash bars, with aluminium sections weighing not less than 0.55kg/m and three track aluminium sections of size 100x38x1.50mm of Make: Jindal/ Hindalco including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, fibre wheel rollers, anodized aluminium fittings such as hinges, tower bolts and handles etc. including glazed with 5mm thick tinted glass and wire meshed with stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F pressed steel door frame of size 105x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F pressed steel door frame of size 125x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

M&L cement concrete 1:3:6 type C-0 using 12.50mm graded stone aggregate as in filling and mass concrete to back of pressed steel frame complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F 28mm thick factory made solid PVC profiled panel door shutter with integral skin as frame & 3mm thick high pressure compact laminate on both sides of approved colour as infill, with ‘C’ type GI or 40x20x19mm of MS pipe as stiffner and fixed in frame at site as per specifications and drawing complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 200mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L in repair 18/19mm thick block boards, grade 2 quality, interior grade, commercial type fixed with screw/nails to timber frame work as in pelmet boxes/ cup boards and cabinets etc including 6mm thick teak wood lipping alround complete all as specified and directed.

M&L 0.90mm thick Decorative laminates type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finished or electro galvanised, with width of flap 30mm when open, and fixed with screws complete all as specified and directed.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F Ball catches (magnet catcher) with 8mm dia steel ball, brass body and striking plate including letting in, overall size 50x15mm and fixed to shutter complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

S&F in repair 20mm dia mild steel chromium plated pipe, superior quality, as in cloth hanging rod with end brackets and fixed with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square, area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F steel windows with side hung shutters including box type hinges or factory made butt hinges with steel handle and steel peg stays etc. complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel ventilators with top hung shutters including box type hinges or factory made butt hinges with steel handle and steel peg stays etc. complete all as specified and directed.

S&F Box type steel windows/ventilators with side hung shutters with glazed and gauzed double panel shutters both provisions including box type hinges or factory made butt hinges with steel handle, tower bolts, hold fasts and steel peg stays etc. complete with glazing bars dovetailed or welded and 10mm square guard bars @ 125mm c/c complete as per CELZ drg No. LZ/C-TD/130 sheet No 1/4 to 4/4 complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F false ceiling with 4mm thick 'E' Board (Make: Everest) of size 600x600mm, white, prelaminated sheet embossed reinforced designer ceiling board tiles of approved texture and powder coated, hot dipped GI imposed grid frame work complete all as specified and directed including all necessary drilling, cutting to fix electrical items as under with the following:- (a) 24x24x0.45mm thick powder coated GI angle plugged @ 600mm c/c along perimeter of wall. (b) 24x32x0.33mm thick powder coated GI tee as main and cross runners suspended with 1.6mm dia GI wire suspenders with adjustable clamps and dash free fastners with rawl plug and screws plugging in RCC slab etc. placed @ 600mm c/c from perimeter of wall. (c) Fixing of 4mm thick 'E' board tiles and finished complete with one coat of oil emulsion distemper on ceiling. NOTE: The complete ceiling work shall be executed as per manufacturer's instructions and as directed.

S&F in repair 12mm thick semi perforated Gypsum tile false ceiling with board of size 600x600mm and powder coated GI snap grid frame work (Make: Armstrong or equivalent as approved) complete all as specified and directed including all necessary drilling, cutting to fix electrical items as under:- (a) 25x25x1.5mm thick GI angle powder coated plugged @ 600mm c/c along perimeter of wall. (b) 25x25x1.5mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders with adjustable clamps and dash free fastners with rawl plug and screws plugging in RCC slab placed @ 605mm c/c from perimeter of wall. (c) Fixing of 12mm thick semi perforated gypsum tiles and finished complete with two coats of oil emulsion distemper over one coat of primer on ceiling. NOTE: The complete ceiling work shall be executed as per manufacturer's instructions and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based plain steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

M&L 6mm thick corrugated or semi corrugated asbestos cement sheet in roofs, walls etc. and fixed with L-type or J-type or cranked hook bolts with washer complete all as specified and directed.

M&L for cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-21 as required; depth of cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

M&L stainless steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work complete all as specified and directed.

M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintel hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L mild steel bolts, purpose made with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc. 12mm dia of neck, length of bolts exc. 30cm long complete all as specified and directed.

M&L structural steel work with rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L structural steel work with rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. and similar articles conforming to Fe-410 Gde E-250 quality-A complete all as specified and directed.

S&F mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes and conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surface of ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of cement base paint over one coat of primer on previously treated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for two coats of white wash on old decorated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in floor finished even and fair without using extra cement as in levelling course complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 350x250x7mm/ 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in vertical surfaces etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F vitrified tiles, double charged, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F vitrified tiles, double charged, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab flooring, machine cut and polished as in vertical surfaces over and including 10mm thick rendering in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including making moulding/rounding to edges of stone complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, rubbing, grinding, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves and partition in cupboards, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, including rubbing, grinding, polishing, making hole for gas pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves etc and similar works set in cement mortar 1:4 complete all as specified and directed.

M&L 100mm thick cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for bed of water tank at top of roof slabs, finished even and smooth without using extra cement complete all as specified and directed.

Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 10cm in girth complete all as specified and directed.

Taking up or down 15mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

Taking up or down 20mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Dismantling of water tanks of capacity exc. 250 litres and not exc. 500 litres of any type and in any position and removing from site complete all as specified and directed.

Dismantling of water tanks of capacity exc. 500 litres and not exc. 1000 litres of any type and in any position and removing from site complete all as specified and directed.

S&F 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F 1000 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F in repair 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated hinging device ISI marked as approved, complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated hinging device ISI marked as approved, complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F in repair vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F vitreous china Wash basin, white, flat back type of size 630x450mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm angle iron etc. complete all as specified and directed.

S&F in repair counter top vitreous china wash basin, coloured, oval shape, approx size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F vitreous china bowl urinal flat back of size 465x355x265mm, white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe), including waste pipe, providing and fixing plugs, bedding urinal against wall etc. complete all as specified and directed.

S&F in repair two way bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F in repair bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F in repair Pillar taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S&F Pillar taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S&F in repair angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F angle valves 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F stop valves concealed type 15mm bore, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair central hole basin mixer, fancy type, brass chromium plated, with round spout with popup waste system, including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair wall mixer with telephonic shower arrangement, connectings legs and wall flanges, fancy type, brass chromium plated, with costed swinging spout including plugging and securing to walls suitable for 15mm bore pipe complete all as specified and directed.

S&F brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F in repair brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F in repair soap dish, brass chromium plated, oval shaped of size 100x50mm (approx), fixed to wall with PVC gully and CP screws complete all as specified and directed.

S&F in repair hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long chrom finish flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed.

S&F in repair toilet paper holder, superior quality, fancy type, brass chromium plated with wall hook bracket complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair PVC bath cabinet/ mirror cabinet (multi utility) with 4mm thick looking mirror of overall size 560x410mm complete all as specified and directed. Make: Commander/ Polytuff/ Prayag

S&F in repair peg set of 6, brass chromium plated, fancy type, with 40mm wide brass CP strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F peg set of 6, brass chromium plated, fancy type, with 40mm wide brass CP strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair 25mm dia mild steel PVC coated curtain rod, superior quality, any colour, with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in reapir kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers, waste coupling and waste pipe, including bedding in cement mortar 1:3 to dwarf wall or fixing cantilever brackets and connecting union to waste pipe, overall size 1145mmx510mm with bowl size 510x405x160mm complete all as specified and directed.

S&F in reapir stainless steel kitchen plate rack (utensil rack) of size 900x750x250mm, made out of 0.8mm thick stainless steel sheet, approved design and fixed to wall with brass screws and PVC gully including all necessary fittings like nuts and bolts etc complete all as specified and directed.

S&F in repair 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repair 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repair cast iron Nahani trap, with grating including jointing to waste pipes, fixed in cement concrete 1:2:4 type B-1 and suitable for 100mm bore pipe complete all as specified and directed.

Demolition and breaking up 100/75mm internal dia of drain pipes (Salt glazed ware, AC or Reinforced concrete), set in cement mortar complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F in repair PVC (SWR) multi floor trap (nahnai trap) with PVC grating including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for 150mm bore salt glazed stoneware drain pipes, complete with collars, laid in trenches and jointed in cement mortar 1:1 as in drains complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete foundation bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for cleaning the exposed concrete surface of floor/ wall/ chajja by brushing & watering and applying one coat of TAPECRETE P-151 Acrylic Polymer Modified Cementitious slurry consisting 1:2 (1 part of tapecrete : 2 parts of cement by weight) and shall be allowed to dry for 4-6 hours, then applying second coat of 1.5mm thick tapecrete brush topping consisting 1:2:2 (1 part of tapecrete : 2 parts of cement : 2 parts of silica sand by weight) over the first coat and cured for next 2 days complete all as specified and directed.

Taking down existing roof tiles carefully and refixing the same after necessary repair work including preparation of base complete all as specified and directed.

M&L for construction of Septic Tank suitable for 25 users with RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in bases, baffle walls, beams, roof slab, cover slab, covers etc., brick work with old size fly ash bricks in CM 1:4 and manhole cover made out of 6mm thick MS steel sheet and frame of angle iron 50x50x6mm including all required earthwork in soft/loose soil, cement concrete etc. complete all as shown on CELZ drawing No. TD/217 sheet 1/2 & 2/2 amended upto date complete all as specified and directed.

M&L construction of Soakage Well of size 1.80m dia, 3.00m effective depth and 4.50m overall depth with fly ash bricks and RCC M-25 Design Mix (using 20 mm graded stone aggregate) as in cover slab etc. including all required earthwork in soft/loose soil, filling of brick bats and cement concrete etc. complete all as shown on CELZ drawing No. TD/576 sheet 1/2 & 2/2 dated 16.06.1989 complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

Taking down carefully main switches, DB's, MCB DB's of any way or rating and making good the disturbed surfaces of walls complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 184 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 184 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item No. 184 above but for One bell/ buzzer point on an independent board controlled by one bell push

All as per item no 184 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, two way 5/6 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F bell push, flush type, single pole, one way 5/6 Amp, 230 volt flush type complete all as specified and directed.

S&F in repair call bell, ding dong type, AC single pole, 230 volt complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, tripple pole and neutral 4 way, 415Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 4 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F in repair MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F in repair MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F in repair MCB, tripple pole & neutral 63 Amp, 415 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F in repair sheet metal enclosures, single pole with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

S&F in repair ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

Taking down old copper/ aluminium sub main wiring or service connection complete all as specified and directed

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6sqmm nominal cross sectional area and one run of 6sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F in repair wall mounted 18/20 W LED integrated tube light fitting of size 1200mm long batten with aluminium housing and decorative end cap and one no 18/20 W LED 6000 K, 230V, with integrated electronic driver complete with all required fittings and fixtures arrangement including and provn of connection from ceiling rose to luminaries with 3 core flexible copper wire complete all as specified and directed. Make: Havells cat no. LUMILINEPLUSBS20WLED865SPCSS or Surya Visco cat no. 18W LED SLEBT 20 IL or C&S cat no. LTT4F20WLED/W.

S&F in repair LED bulk head light fitting, made of cast aluminium body with heat resistance pressure, die cast housing, IP-65 protection cover and one no. 7 W LED, 6000K, including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Philips (VISTAGLOW) cat no. WT140W LED7S CW PSU S1 PC or C&S Cirius series cat no. LTB7W LED or Havells cat no. LHEOAOP7UZ6W010.

S&F in repair wall mounted, 9/10 W LED mirror light fittings of size 600mm long with integrated Batten and LED 9/10 W, 6000 K, 230V with polycarbonate housing & integrated electronic driver including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Havells cat no. Lumiline plus BS 10WLED865SPCSS or C&S NAKSHATRA cat no. LTDC01210WLED/WD or Surya Visco cat no. SLE BT 10.

S&F in repair security light fitting of 25 W LED 6000 K, with high power LED source (more than 100 lumens per watt), PDC housing, IP65 with 4KV inbuilt surge protection driver and one no. 25W LED tube, with all accessories, prewired with and fixed to bldg/pole including GI bracket 1.20m long bent to shape, made out of 40mm dia GI light grade pipe with nuts, bolts and washers and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Havells Endura Pearl cat no. ENDURAPEARLSL25WLED757SASYTOPCMP or Surya Lexon Cat Part No. SLE UL 25W IP 66(LXN)/ C&S (Indus E Series) with cat Part No.LTESS25WLED/LS.

S&F super bright LED (2X2) light fitting, 36 W, 6000 K recess mounting with high efficent LED source with 02 nos LED Light and all accessories, prewired complete all as specified and directed. Make: Surya Celesta cat no. SLE DS 36 22R or C&S cygnus-c series cat no. LTCRP36WLED2x2 or Philips cat no. RC380B LED30S-6500 G4 L60W60 PSU OD OC.

S&F in repair integrated LED Post top lantern with high power 25/30 W LED as light source, energy saving, envioronmental friendly, long life asethetically designed with symmetrical light distribution, spun auminium landscape lumainaire incl LED driver complete and incl neceesary electrical connection complete all as specified and as directed. Make: C&S cetus cat no. LTGLC30WHPLED/W or Havells cat no. Ruby Clear RUBYPT25WLED757PSYMTOPS or Surya E-TOPP cat no. SLE PT 30W-ETPP

S&F in repair of recessed type square LED 12W downlighter of dia 160x160mm as required complete all as per specified and directed. Make: C&S CARINA series cat no. LTCRSLM12HPLEDSQ/W or Havells edge pro cat no. EDGEPROSQDLR12WLED840S or Surya stellar cat no. SLEDLS12 XX stellar SQ.

S&F in repair decorative wall light fittings made out of polycarbonate, (Spiral B-22 base) with 01 No. 9 W LED Bulb, 230 V, 6000K, complete including required fixing arrangements complete all as specified and directed. Make: Havells cat no. CITY 1 LHDL02160099 or Bajaj cat no. BJLF1 15W RF or equivalent in Philips/ C&S.

S&F in replacement LED bulb 7/9 W, B-22 base, 6000K complete all as specified and directed. Make: Havells cat no. LHLDEUEEML8R007 or Surya cat No. 10W NEO PLUS LED or C&S cat no. LTHPLEDLAMP7WB22BULB.

S&F in replacement of GI pipe light grade bracket, 32 mm bore, 1 mtr long bend in required shape and MS clamp 40x3mm thick duly painted with two coats of synthetic enemal paint over a coat of red oxide primer fixed on wall including bolts and nuts complete all as specified and directed.

M&L Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected to galvanised earth lead wire 4.0mm dia (7.50m) by means of bolts, nuts, check nuts & washers of galvanised iron or steel, earth lead wire protected by 15mm dia GI pipe light grade, 20mm dia light grade GI pipe for watering, meshed funnel, alternate layer of charcoal and common salt complete all as SSR Item No. 19471 and shown in electrical plate No. 3 of SSR part-I with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way in lieu of CI pit cover and protection including necessary excavation and earth work complete all as specified and directed.

S&F ceiling fan 1400mm sweep, BEE star rated, copper wound, AC single phase, 230/240 volts complete with fan motor, blade, down rod, canopy and provn of connection with three core flexible copper wire cable of size 1.50sqmm from ceiling rose to fan complete all as specified and directed. Make: Orient (Energy Star) or Khaitan (Magma high speed anti dust) or Havells (Energy saving mode ES neo) or Usha (Energy saving technix plus).

Taking down carefully ceiling fan/ exhaust fan by disconnecting all electrical connection, proper cleaning and refixing the same including all electric connections with twin core flexible copper wire 23/0.0076 size after necessary repair work complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for laying for cables etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for sand filling under floors or in foundatoins as in sand cushioning including spreading, levelling, watering and well ramming complete all as specified and directed.

Supplying & laying sub class 'B' bricks old size over LT/HT cable laid flat for protection of cable complete all as specified and directed.

M&L 40mm bore GI tubing light grade including necessary fittings laid in trenches, under road crossing, fixed on poles, walls, under floors etc complete all as specified and directed.

S&F 1100V grade heavy duty XLPE armoured cable, PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection of size 6sqmm, 2 core cable complete all as specified and as directed

M/s Sudhir Enterprises