41/PR/BSPTCL/2026

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.All kinds of soil

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m disposed soil to be leveled and neatly dressed :All kinds of soil

Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead

Supplying and filling in plinth with local sand under floors including, watering, ramming consolidating and dressing complete.

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length belowpile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :,300 mm dia piles

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :Cement mortar 1.:4 (1 cement: 4 coarse sand )

Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1.:4 (1 cement: 4 coarse sand )

Extra for Brick work in superstructure above plinth level upto floor V cum.

Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in superstructure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shutering-all work upto plinth level. 1:4:8 ( 1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level.1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.@ 1 kg per 50kg of cement.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mmnominal size, well rammed and consolidated and grouted withfine sand, including finishing the top smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work upto plinth level.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All work above Plinth level upto floor V Level.Concrete of M-25 grade with minimum cement content of 330 kg/cum

Centring and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc.for mass concrete.

Centring and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform.

Centring and shuttering including strutting, propping etc. and removal of form for:Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and shuttering including strutting, propping etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

Centring and shuttering including strutting, propping etc. and removal of form for:Stairs,(excluding landings) except spiral-staircaces.

Centring and shuttering including strutting, propping etc. and removal of form for: Edges of slabs and breaks in floors and walls Under 20 cms wide

Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete excluding plastering of the jambs, sills and soffits.50 mm thick

Reinforcement for R.C.C work including straighting,cutting bending,Placing in position and binding all complets.

Thermo-Mechanically Treated bars TMTC-500-8mm dia

Thermo-Mechanically Treated bars TMTC-500-10mm dia

Thermo-Mechanically Treated bars TMTC-500-12mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 16mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 20mm dia

Thermo-Mechanically Treated bars TMT Fe-500- 25mm dia

Providing desination 100 A one brick flat soling joints filled with local sand including cost of watering texes, roualty all complete as per building specification and direction of E/l.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B) including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in Charge and panelling with panels of:12 mm thick prelaminated (with decorative lamination on one side and balancing lamination on other side) particle board Grade -1 medium density flat pressed, three layer and graded (FPT-1) conforming to IS :3087 bonded with BWP type synthetic resin adhesive as per IS :848 and prelamination conforming to IS :12823 Grade-1 Type II

Providing and fixing aluminium tower bolts ISI Marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:300x10mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:100 mm

Providing and fixing aluminium hanging floor door stopper ISI Marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete.Twin rubber stopper

Providing and fixing bright finished brass 100mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut jointed and fusion welded together, including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer’s specification and direction of engineer-incharge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer’s specification and direction of engineer-incharge.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track four panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 4.00 sqm upto 8.00 sqm)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptableTwo track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade.Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite black

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size

Size of Tile 600 x 600 mm

Glazed Vitrified tiles Matt/ Antiskid finish of size

Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

12mm cement plaster of mix:

12mm cement plaster of mix:

15 mm cement plaster on rough side of single or half brick wall of mix.

20mm cement plaster of mix :

6mm cement plaster to ceiling of mix:

Extra for providing and mixing water proofing material in proportion recommended by the manufacturers:

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Finishing walls with textured exterior paint of required shade

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat: With ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Supplying and filling good quality cinder in downslabs etc, all complete as per building specification and direction of E/I.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450 N/5 cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane.3mm thick

Extra for providing and mixing water proofing material in proportion recommended by the manufacturers:15 mm cement plaster 1:4(1 cement :4 sand)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni).

Steel work welded in built up sections/framed work including cutting hoisting fixing in position and applying priming coat of approved steel primer using structural steel etc. as required. In grattings, frame, guard bar ladders, railing, gates and similar work etc

Providing and fixing 12 mm thick frameless toughend glass door shutter of approved brand and manufature, including provinding and fixing top and bottom pivot and spring type fixing arrangement and making necessary holes etc. for fixing required door fitings all complete as per direction of engineer in charge .

Provind and placing on terrace (at all floor levels) polythene water storage tank ISI:12701, marked with cover and suitable locking arrangement and making necessary holes.

Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.

Providing and fixing to filter and lowering to proper levels 40 mm G.I.pipe for tube well including cleaning and priming the tube well.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets: 25 mm dia (heavy type).

1 Hp Motor pump

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness(weight not less than 12.50 kg/sqm)

Providing and fixing double gazed hermetically sealed glazing in aluminium windows ventilators and partitions etc. with 6 mm thick clea r float glass all complete as per direction of engineer in charge .

Providing and fixing Rimless Bowl With Cistern For Coupled WC With UF Soft Close Slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories And Accessories Set, Size: 380x610x805 mm, P Trap- 180 mm

Providing and fixing Counter Top Basin, Size: 600x400x185 mm (SLS-WHT-6601-Jaguar)

Providing and fixing Built-in Bathtub,Built in Bath tub with frame, Built in Bath tub.(JBT-WHT-LAGUNA180FX)

Providing & fixing of shower panel of approved brand and as per the description. (TSHP-BLK-JA011-Jaguar)r.all complete. specification and direction of Engineer-in-charge.

Providing and fixing 12 mm thick frameless toughend glass partitions of approved brand including provinding and fixing top and bottom pivot, and making necessary holes for fixing glass partitions inclusing all fittings etc. complete in all respect as per direction of engineer in charge

Providing & fixing of Wall Mixer 3-in-1 System with Provision for both Hand Shower & Overhead Shower Complete with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Flanges (without Hand & Overhead Shower) (CQT-CHR-23281UPR-jguar)

Providing & fixing of Overhead Shower 200X200mm Square Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System. (OHS-CHR-35497)

providing and fixing Urinal (URS-WHT-13261)Urinal Valve Auto Closing System with Built-in Control Cock & Wall Flange (PRS-CHR-077) all Fixing Accessories, Size: 355x340x535 mm complete in all respect.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.White Agaria Marble Stone

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board 510x1040mm bowl depth 178mm

Provding and fixing PVC waste pipe for sink & wash basin including PVC waste fittings completeSemi rigid pipe 40 mm dia

Provding and fixing 600X450mm beveled edge mirror of superior glass complete with 6mm thick hard board ground fixed to wooden cieats with CP brass screws & washers complete.

Providing and fixing Toilet Paper.holder: Vitreous china

Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezodial shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour. Weighing not less than 88 gms.

Provding and fixing PVC Soil ,Waste & vent pipes all complete

Provding and fixing PVC fittings all complete as/specification & directionof E/I

110 mm vent cowel

110 mm plain bend

110 mm door bend

110 X 110 mm dia door tee

110 X 110 mm dia plain-y

110 mm pipe clip

110 X110 mm dia p-trap

110 mm dia X 45 Bend

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm Nominal outer dia pipes

25 mm Nominal outer dia pipes

32 mm Nominal outer dia pipes

40 mm Nominal outer dia pipes

50 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm Nominal outer dia pipes

20 mm Nominal outer dia pipes

25 mm Nominal outer dia pipes

32 mm Nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality.

Providing and fixing uplasticised PVC connection pipe with brass unions.

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and fixing C.P. brass bib cock of approved quality conforming to IS :8931.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms.

Constructing masonry Chamber 60 x 60 x 75 cm inside, in brick work in cement mortar 1:4(1 cement: 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necesary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3( 1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:

Providing and fixing square mouth SW gully trap grade A complete with CI grating brick masonry chamber with water tight CI cover with frame of 300X300mm size(inside) the wt. of cover to be not less than4.50kg. And frame to not less than 2.70 kg. as/standard design

Providing and laying non -pressure NP2 class R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc.

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Extra for depth for manholes

Constructing brick masonry chamber for underground C.I inspection chamber and bends with 75 class designation bricks in cement mortr 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Extra for depth beyond 45cm of brick masonry chamber:

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with brick of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Supplying materials, labour for constructing Septic Tanks of following sizes & as per sections given in the Drawings & Designs, all complete as per specifications and direction of Engineer-in-charge.

Providing and fixing on wall face PVC (working pressure 4kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

110 mm Coupler

110 mm Single pushfit Coupler:

110 x 110 x 110 mmSingle tee with door

110 mm bend 87.50

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Factory made 18mm thick single extruded wpc (wood polymer composite) solid panel board jali.

Supplying and stacking at site.

90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate

53 mm to 22.4 mm size stone aggregate

Stone screening 13.2 mm nominal size (Type A)

Stone screening 11.2 mm nominal size (Type B)

Red bajri

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and laying 60 mm thick factory made cement concreteinterlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Providing of MS Angle ( 50 X 50 X 6 ) mm in proper shape is required as per direction of E/I

Drilling 6mm Dia. In M.S. angle iron for fixing of staples etc. as per building specification and direction of E/l.

Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building specification and direction of E/l.

Welding by electric plant including of transportation of electric welding at site etc complete as per direction of E/I

supply of Galvanised steeL barbed wire fencing all complete as per direction of E/I.

Labour for fitting and fixing barbed wire fencing in six rows horizontal up to a height of 1.85m and two diagonals including fixing of post in cement concrete at 2.5m centres including cost of staples (but excluding the cost of cement concrete, angle, iron post, its cutting and making holes, nuts & bolts) all complete as per building specification and direction of E/l.

Steel work welded in built up sections/framed work including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%). flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment).

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed

Planting of tree by the road side (Bottel palm trees, golden fycus, foxtell, etc.) in .6m dia holes, 1 m deep dug in the ground , mixing the soil the with decayed farm yard/ sludge manure, planting the sapling, backfilling the trench, watering, fixing the tree guard …...... as per direction of E/I

Providing and planting healthy, well-grown hedge plants of approved species and variety, suitable for local climatic conditions, including preparation of soil, digging of pits, supply and mixing of good quality garden soil, farmyard manure/compost, planting, watering, initial maintenance and replacement of dead/damaged plants, complete as directed of E/I.

Filling available excavated earth (exclude rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each oeposited layer by ramming and watering lead

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Carraige of materials

Coarse sand

Stone aggregate

Brick

local sand

Earth

Extra Cost of Materials

Cement

Brick

Wiring for light point/ fan point/ exhaust fan point / call bell point with 1.5 Sq.mm FR PVC insulated copper conductor cable in surface/ recessed medium class PVC conduit with modular switch , modular plate suitable size G.I. box etc as required.

One light point controlled by 1 no. 10 A modular switch.

Two light point controlled by 1 no. 10 A modular switch.

Wiring for light plug, & circut with 2x2.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No.2.5 sq mm FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring for power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No.4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring for submain with 4x6 sq.mm +1X6 sq mm earth wire FR PVC insulated copper conductor single core cable in recessed PVC conduit as required. (For L DB UPS Room )

Wiring for circuit with 4x10 sq.mm +1X10 sq mm earth wire FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit as required.(P.DB & Lift Room)

Wiring for submain with 2x6 sq.mm +1X6 sq mm earth wire FR PVC insulated copper conductor single core cable in recessed PVC conduit as required.( For Computer DB)

Supply & fixing following size medium class pvc conduit along with accessories in surface/recess including cutting of wall and making good the same in case of recessed conduit as required.

(a)20 mm dia

(b)25 mm dia

Supplying and fixing metal/ PVC box of following sizes ( nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

(a)75mmX75mmX50mm deep

(b)200mmX150mmX60mm deep

Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches/ socket/TV / Telephone outlet in surface/ recess etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps moduler socket outlet & 6A modular type switch connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/ 16 amps moduler socket outlet & 15/16A modular type switch connection etc. as required.

Supplying and fixing TPN sheet steel enclosure on surface or in recess along ,with 32 amp 415 volts 'C' series, TPN, MCB , complete with connections testing and commissioning etc. as required.(For UPS Room)

Supplying and fixing TPN sheet steel enclosure on surface or in recess along ,with 63 amp 415 volts 'C' series, TPN, MCB , complete with connections testing and commissioning etc. as required.(For Lift Room)

Supplying and fixing of 25A Dp with indicator with key tag ,box and plate of Norisys make in positon recessed in wall including connection testing etc as required

Supplying fitting fixing of dingdong call bell suitable for DC/AC single phase 230 volts,complete etc as required.

Supplying and fixing modular blanking plate on the existing modular plate & metal box excluding modular plate, etc. as required.

Supplying and fixing 2+ 12 way double door horizontal type single pole and Neutral sheet steel M.C.B. Distribution board, 240 Volts,on surface/ recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar, interconnection, powder painted including earthing etc. as required (But without MCB/ RCCB / Isolator)

Supplying and fixing cable end box ( Loose wire box , IP 43) suitable for following sheet steel M.C.B. Distribution board, on surface/ recess, complete with testing commissioning etc. as required

(i) For 4 way Double door MCB TPN DB

(ii) For 12 way Double door MCB SPN DB

Supplying and fixing of following rating C series MCB suitable for inductive and other loads of following poles in the existing MCB DB complete witth connections ,testing and commissioning etc. as required .

6 Amp. To 32 Amp. SP MCB 240 Volt

32 Amp SPN MCB 240 Volt

Supplying and fixing of wall/floor mounted cubicle panel board fabricated with 16 guage iron sheet suitable for panel mounted switch disconnector, including busbar chamber, insulator, nut-bolt painting etc as required. (But without busbar copper strip)

Supplying and fixing of following rating electrical items in the existing cubical panel board including drilling holes in cubicle panel making connections etc. as required.

(i)160 Amp 36 KA FP 415 volt MCCB.

(ii) 160 Amp, 4 pole changeover switch.

(iii)100 Amp 30 KA FP 415 volt MCCB.

(iv) 100 Amp, 4 pole changeover switch.

(v) 40 Amp TPN MCB 415 Volt

(vi) 32 Amp TPN MCB 415 Volt

(vii) 32 Amp SPN MCB 240 Volt

Providing and fixing MV danger notice plate of 200mmX150mm made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc as required.

Earthing with copper earth plate 600mm X600 mm X3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with salt and charcoal/ coke and salt as required.

Earthing with G.I earth pipe 4.5 mt. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with Charcoal/coke and salt as required.

Providing and laying 25mm x 5mm Copper strip in 40 mm. Dia copper pipe from earth electrode including connection with brass nut, bolt, washer, excavation and refilling etc. as required.

Providing and fixing 4mm dia copper wire on surface or in recess for loop earthing etc as required.

Supply and Installation of regular / standard model A.C. ceiling fan of 1200 mm sweep and regulator including wiring the down rod of standard length (upto 30cm) with 1.5 sq.mm FR PVC insulated copper conductor, single core cable etc. as required.

Supplying and fixing stepped type electronic fan regulator on the existing switch box including connections excluding modular plate etc. as required.

Supply and Installation of 300mm sweep 230 A.C. exhaust fan in the existing opening including making good the damage connection testing commissioning etc. as required.

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.150 mm sweep (1300/1400 RPM)

Supplying and fixing 4'X18 wat[ LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS pVC insulated copper conductor etc. as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing fotrlowing types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on poleibuilding including connection earthing the body etc as required. 30 watt

Supplying and fixing 2 pin 5 Amp ceiling rose on the existing junction box/ PVC box including connection etc as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supply of PVC insulated PVC sheathed aluminium conductor armoured under ground cable of graded 1.1 KV for working voltage upto 1100 volts conforming to ISI 1554 (Part-I) of 1964 with upto date amendment as detailed below.

(a) 3.5 Core 120 sq mm

Laying of one number PVC insulated and PVC sheathed/ XLE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushionig, protective covering and refilling the trench etc. as required.

(a) Above 95 sq. mm. and upto 185 sq.mm

In fig

Coarse sand

Stone Aggregate

local sand

Earth

Soil investigation (At least 3 nos. of borehole)

Design and engineering- Development of preparation of detailed Architectural, structural, MEP design and drawings and shop drawings of the guest house building and associated works, Sanitary/Water Supply/Electrical/AC Services, Site Development & external Services complete in all respect.

Modular Conference Table for 16 Person: Material of work top -25 mm thick prelaminated particle board, Table top plain side-Edge banded with PVC tape of 2 mm thick with help of hot melt glue, Material of Gable end and modesty panel-18 Mm Thick Three Layers Prelaminated Particle Boards Of Grade-II Type-III Of IS:12823/Latest Both Sides Particle Boards Matching With Top Shade In Grade-II Type-III, Length of Each Seat of Work Top ± 20 mm- 675 mm for single AND 1350 mm For dual,Depth of Work Top-600mm, Height of Work Top-750 mm, Corners of work top -850 mm, Table top finish-Laminate In Colour With matt Finish 0.6-0.8 Mm Thickness Of Type S,F Or P Having Index Number 3.2.3 Conforming To IS:2046/Latest With Having Balancing Laminate Of 0.5 Mm Thick On Other Side.

Highback Chair: SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression, Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D), BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette HIGH BACK SIZE: 47.7 cm. (W) x 76.4 cm. (D) , The armrest top is moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanism is designed with the following features: 360' revolving type, Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position Tilt limiter giving option of variable tilt angle to the chair, The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm, ADJUSTABLE BACK SUPPORT : Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need, Overall Size-76.1W x 76.1D x 112.7-130.2H x 43.1 -53.1 SH cm.

Fullback Chair: SEAT ASSEMBLY: The seat is made up of 1.4 + 0.1 cm thick hot – pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 49.5cm (W)x 51.8cm(D). BACK ASSEMBLY: The Back is injection moulded in Glassfilled Polypropylene whichis upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 +0.1 cm. BACK SIZE: 44.5 cm(W) x 57.5 cm(H). POLYURETHANE FOAM: The polyurethane foarn for seat is of density = 30 + 2kg/m*. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.040.1cm height.}t also has swivel and To and Fro adjustment with moulded PU armtop. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment is chrome plated with an adjustment stroke of 10.0 + 0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0 +0.5 cm P.C.D. TWIN WHEEL CASTORS: The twin whee! castorsareAnjectionmoulded in) black Polypropylene having 5.0+ 0.1cm wheel Diameter.

Reception Table of size (2400W X 725D X 740H):ReceptionTable of size ( (2400W X 725D X 740H) Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Length - 2400mm, Depth - 1770mm, Height - 740mm. Access Flap along with a Gromett is provided on work surface for wire management Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes.Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging.

Midback Chair: seat/back assembly: the seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area back size 47.5 cm. (w) x58.0 cm (h)seat size 47.0 cm. (w) x 48.0 cm. (d) high resilience (hr) polyurethane foam: the hr polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. armrests :the one-piece armrests should be injection moulded from black co-polymer polypropylene. center tilt synchro mechanism: the mechanism should be designed with the following features: • 360° revolving type. • upright-position locking • tilt tension adjustment • seat/back tilting ratio of 1:3. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.telescopic bellow assemblythe bellow should be 3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly:the pedestal should be injection moulded in black 33% glass-filled nylon-66 and fitted with 5 nos. twin wheel castors. the pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). 8.twin wheel castors:the twin wheel castors should be injection moulded in black nylon.

3 Seater Sofa: Providing, placing and supplying of sofa: Dimensions W x H x D (cm) 179 x 85 x 83.5 Finish Color:Cappuccino Weight:85.00 kgs Sofa Seating Capacity:3 Seater Storage Included:No Warranty:1 Year Warranty ⁠Upholstery Material:Leatherette.

Coffee Table: Dimensions W x H x D (cm)-120 x 45 x 60 Material : 18 mm thk prelaminated particle board, Shade : Remini Walnut Construction : Knock down, Finish : MIP lamination in Remini Walnut shade with matching lipping in Matt finish. MIP lamination in Cloud Grey shade with matching lipping in Matt finish.

King Bed: Providing, placing and supplying of premium leatherette upholstered bed with hydraulic pullout mechanism: Overall Size :Length - 2440 mm Width - 2370 mm Height - 990 mm Material: Bed Structure consist of engineered wood frame of suitable members and structures with structural adequacy compliant to a king size and Premium Leatherette & Engineered Wood headboard material. Headboard height- 730mm.

Mattress of size (78"x72"x5"): Dimensions W x H x D (cm) 182.88 x 198.12 x 12.7 Mattress Dimensions L x W x T (cm) 78 x 72 x 4, Finish Color:White, Weight:26.20 kgs, Layers:Multiple, Mattress Size:King, Warranty:10 Years, Primary Material:Foam, Upholstery Material:Jacquard Fabric.

Pillow of size (425L X 675W): Size ( in cm) : 43 x 69 Fibres : 15 Dn Conjugated silconized Fabre weight - 650 Fabric - Flower Embossed 90 GSm Polyester Packaging - Nonwoven Fabric Packaging .

Bedside Table: Bedside Table of size 455D x 610W x 504H,Frame Material-Wood, Weight - 17.6 Kgs; Top Material - Engineering Wood; The bedside table comes with two drawers that offer plenty of storage space for your belongings.

3 Door Wardrobe: Primary Material: Engineered Wood,Width x Height: 132.1 cm x 191 cm (4 ft 4 in x 6 ft 3 in),Number Of Doors: 3,Number Of Shelves: 10,The design inspired from a bar of chocolate, it comes with a wenge finish that looks elegant.The 3 door wardrobe does not only pack smart storage options with its multiple drawers and shelves but can be easily expanded into a bigger unit by connecting it with other wardrobes, overhead storage, dressers etc.

Dressing Table: Product Dimensions: W x H x D, 90 x 171.19 x 45.5 (cm),Primary Material: Particle Board,Colour: Cola Rain, Finish: Matte, Style: Contemporary,With multiple drawers and shelves, you can store your beauty products and appliances in the drawers, the perfumes and hair brushes can be placed on the surface for display.

Study Table: Product Dimensions: W x H x D, 60.5D x 120W x 101.8H Centimeters; Top Material: Engineering Wood; Dark Color Palette, Spacious Table Top, Chest Of Drawers, Storage Shelves, Metallic Handles.

Fullback Chair: SEAT ASSEMBLY: The seat is made up of 1.4 + 0.1 cm thick hot – pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 49.5cm (W)x 51.8cm(D). BACK ASSEMBLY: The Back is injection moulded in Glassfilled Polypropylene whichis upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 +0.1 cm. BACK SIZE: 44.5 cm(W) x 57.5 cm(H). POLYURETHANE FOAM: The polyurethane foarn for seat is of density = 30 + 2kg/m*. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.040.1cm height.}t also has swivel and To and Fro adjustment with moulded PU armtop. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment is chrome plated with an adjustment stroke of 10.0 + 0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.0 +0.5 cm P.C.D. TWIN WHEEL CASTORS: The twin whee! castorsareAnjectionmoulded in) black Polypropylene having 5.0+ 0.1cm wheel Diameter.

(3+1+1) Seater Sofa Set: Product Dimension: 3 Str sofa of size W x H x D: 1820 x 890 x 920 (mm); 1 Str Sofa of size (920 x 890 x 920) (mm); Finish Colour: Brown; Upholstery Material: Leather; Solid Wood.

Coffee Table : Product Dimensions: W x H x D: 120 x 45 x 60 (cm); Finish Colour: Remini Walnut; Weight - 29 Kgs; Prelaminated Particle Board; Primary Material: Wood. Construction : Knock down.

4 Seater Dining Table with Chairs: Dimension: W x H x D (117 x 75.94 x 75.93)cm; Finish Colour: Brown ; Material: Sheesham Construction: Knockdown; Wood Rectangular Dining Table, a durable, traditional-style dining set made from Sheesham wood that includes a table and four chairs. It is designed to be sturdy with a rich texture and a warm, traditional look. Dining Chair" likely refers to a chair from the Godrej Interio "Grande Advance" or "Grande Pro" dining sets, which are typically made from solid sheesham wood. These chairs have a sturdy construction with a long-lasting finish and are designed for a dining environment. Synthetic leather upholstery.

King Bed: Providing, placing and supplying of premium leatherette upholstered bed with hydraulic pullout mechanism: Overall Size :Length - 2440 mm Width - 2370 mm Height - 990 mm Material: Bed Structure consist of engineered wood frame of suitable members and structures with structural adequacy compliant to a king size and Premium Leatherette & Engineered Wood headboard material. Headboard height- 730mm.

Bedside Table: Providing, placing and supplying of bedside table: Overall Size : Depth - 461.0 mm Width - 460.0 mm Height - 510.0 mm Material :Body panels of Bed side table are made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Drawer front & Door are made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trim fixed on to it. Hardware : The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich.. Construction : Knock Down construction.Packets : 1 packet.Finish :. 18 mm thick Prelaminated Particle Board is in Maple shade.

Dressing Table: W x H x D: 46 cm x 171 cm x 46.1 cm (1 ft 6 in x 5 ft 7 in x 1 ft 6 in)Mirror W x H: 362 mm x 1156 mm Zurina dressing table comes with a long mirror, two storage drawers, and a stool. Available in wenge color, the dresser is crafted from good quality MDF wood, making it sturdy and lasting. The shelves of this stylish dressing table can be used to keep items like perfume bottles, hair products, and medicines, for that clutter-free look. The stool, also wenge color with an orange colored cushion, offers comfortable seating, while the full length mirror is perfect to dress up, and check your overall ensemble.

2 Door Wardrobe: Zurina 2 Door Wardrobe of size (957W x 1938H x 589D)mm good quality MDF wood, making it sturdy and lasting. Finish Colour: Wenge, Weight: 117 Kgs ; Door Type: Hinged; 1 Drawer and No Locker.

Mattress of size (78"x72"x5"): Dimensions W x H x D (cm) 182.88 x 198.12 x 12.7 Mattress Dimensions L x W x T (cm) 78 x 72 x 4, Finish Color:White, Weight:26.20 kgs, Layers:Multiple, Mattress Size:King, Warranty:10 Years, Primary Material:Foam, Upholstery Material:Jacquard Fabric.

Pillow of size (425L X 675W): Size ( in cm) : 43 x 69 Fibres : 15 Dn Conjugated silconized Fabre weight - 650 Fabric - Flower Embossed 90 GSm Polyester Packaging - Nonwoven Fabric Packaging .

Bedsheet with Pillow Cover: Often designed with rich digital prints, vibrant motifs, and quilted fabrics suited for a standard Indian double/king bed size.

Study Table: Dimension-600D x 900W x 713H, All Panels made from 18mm thick Prelaminated Particle Boards with 0.8 mm thick edge bandin,Material- Particle Board, Primary Material- Engineered Wood. Colour- Imperial Oak.

Mesh Fullback Chair: SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area.The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam ismoulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25%compression. ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert.CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features:360° revolving type.· 3 position locking with anti shock mechanism.· Tilt tension adjustment HEADREST: The Headrest sub-assembly is made up of injection moulded glass filledPolypropylene which is upholstered with moulded HR polyurethane foam and fabric.

3 Seater Sofa: 3str sofa-W x H x D: 2040 x 970 x 960, Upholestry: Synthetic,Filling Material: Foam,The sofa offers generous lumbar support, which engulfs your entire back area. It features a synthetic leather upholstery, giving it a smooth and rich finish.Built with sturdy PVC legs, the designer soft sofa.

1 Seater Sofa: 1str sofa- W x H x D: 1000 x 970 x 960, Upholestry: Synthetic,Filling Material: Foam,The sofa offers generous lumbar support, which engulfs your entire back area. It features a synthetic leather upholstery, giving it a smooth and rich finish.Built with sturdy PVC legs, the designer soft sofa.

Coffee Table: Product Dimensions: W x H x D: 120 x 45 x 60 (cm); Finish Colour: Remini Walnut; Weight - 29 Kgs; Prelaminated Particle Board; Primary Material: Wood. Construction : Knock down.

6 seater Dining Table: Dimensions W x H x D (150 x 75 x 90)cm · Finish Color: Indian Mahogany · Weight: 30.00 kgs. The Leo V2 table is made of sturdy rubber wood in a rich mahogany finish and includes two glass accents on the top for an added aesthetic flair.

Dining Chair: Providing, placing and supplying of dining chair: Overall dimensions: 980 x 440 x 540 BACK REST MATERIALS & SIZE:Lamination & Solid Wood: 22mm BACK LEG MATERIALS & SIZE:Lamination : 38x28mm FRONT LEG MATERIALS & SIZE:Solid Wood : 1.5x1.538x38mm FRONT/SIDE/BACK PANEL METERIALS & SIZE :Solid Wood : 22mm FINISHING:AC Finishing Indian Mahogany(3057).

Supplying, Installing, Testing, Commissioning of 1.5 T inverter AC including appropriate stabilizer complete setup of Make- (Daikin/Carrier/Hitachi/Voltas) all complete job as per direction of E/I. - Note - 5 Star Rating Invertor AC

Supplying, Installing, Testing, Commissioning of 2.0 T inverter AC including appropriate stabilizer complete setup of Make- (Daikin/Carrier/Hitachi/Voltas) all complete job as per direction of E/I.Note - 5 Star Rating Invertor AC

Supplying, Installing, Testing, Commissioning of 25 L gyser including complete setup of Make- (Havells /Bajaj /Crompton /Rocia /AO Smith) all complete job as per direction of E/I. Note - Gyser with 5 Star Rating

Supplying, Installing, Testing, Commissioning of 325 L refrigerator including complete setup of Make- (Samusng /LG /Hairer) all complete job as per direction of E/I. Note - Refrigerator with energy efficient.

Supplying, Installing, Testing, Commissioning of 45 L refrigerator including complete setup of Make- (Samusng /LG /Hairer) all complete job as per direction of E/I. Note - Refrigerator with energy efficient.

Supplying, Installing, Testing, Commissioning of 108 cm (43 inches) The Frame Series 4K Ultra HD Smart QLED TV television including complete setup of Make- (Samusng /LGand equivalent) all complete job as per direction of E/I. Note - Television with energy efficient.

Supplying, Installing, Testing, Commissioning of138 cm (55 inches) 4K Ultra HD Smart NEO QLED TV television including complete setup of Make- (Samusng /LG and equivalent) all complete job as per direction of E/I. Note - Television with energy efficient.

Supplying, Installing, Testing, Commissioning of 20 l water purifer including complete setup of Make- (aquaguard , kent, LG , Bluestar/AO Smith ) all complete job as per direction of E/I.

Supplying Installation ,Testing and Commissioning of Passenger elevator of capacity of 8 persons / 544 Kg complete with Specifications and Following requirements : i Load and Speed @ 1.00 MPS.