Balance work of Construction of girls hostel (120 bedded) at Mayong HS School

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand :8 coarse aggregate by volume

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (ii)Super Ductile (SD) TMT reinforcement bars

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. B)Using 25mm thick plank.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides of tie beams, grade beams etc. at or below ground level. (b) Using 25mm thick plank

Providing form work of ordinary timber planking so as In clivn n rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M. II)Using 25mm thick plank

Providing form work of ordinary timber planking so as In clivn n rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as In clivn n rough finish including centering, shuttering, strutting and propping etc Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank).

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate etc. foundation, footings (I) Using mixture machine (A) In sub - structure up to plinth level (b) M20 or Prop 1:11/2:3

(B) Providing and laying plain/reinforced cement croncrete works ement with coarse sand & 20mm down graded stone ;Iggiegate including dewatering if necessary, and curing i.omplete but excluding cost of form work and reinforcement for iiiinforced cement concrete work (form work and reinforcement will he measured and paid separately). (B) Super-structure from plinth level upto 1st floor level. (ii) Columnpillars, posts. souls, suspended floor, roof, landing, shelf and support, hirk;ony, lintel, sill band, beam, girder, bressumer, cantilever, etc. nosing. (b)M20 or Prop. 1:1.5:3

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level. (c). In1:5.

Earth/ sand filling in plinth in layers not more than 150mm thick Including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

112 mm thick 1st class brick nogged wall in cement mortar Including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding MS rod/Tor steel of column to be embeded in cement mortar And will be measured and paid separately) (b). In cement mortar in proportion 1:5. (1 cement:5 sand)

Supplying, fitting and fixing door frame made of M.S. equal angle of size 40mmx40mmx5mm fabricated, welded, mitred and joined as per relevant I.S. Codes including fitting 8 nos. of M.S. hold fast, providing closing/ holding device for 2 nos. tower bolts of door for each side and 1 no. for fitting and fixing Aldrop (for single leaf) to the frame for fixing the door to the frame, applying primer to all steel surfaces fixing the frame to the wall/ R.C.C. members by embedding the hold fast securely in C.C. block of M-15 grade complete at all levels as specified and directed. (Door hinges to be paid as per relevant item of the schedule of rates).

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. b) Using other ISI marked approved brand tube

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (ii) 0.45 mm thick

Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (ii) 0.45 mm thick

Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 000mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm or Everest E-Grid 1510(only for 4mm board). Using 4mm/6mm thick High Pressure Steam Cured Everest Non Asbestos Fibre Cement Board of M/s Everest Industries Ltd. as per IS 14862, to be everest ceiling 4mm thick

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level Including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (b). In cement mortar 1:5

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, Internal rounded angles, not exceeding 80mm girth etc. directed. (a) rough side (b). In cement mortar 1:4

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement 1 coarse sand : 2 coarse aggregate of size 10mm down) laid In panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed.

25 mm thick cement concrete topping 1:2:4 (lcement : 2 Coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish (base Concrete to be measured and paid separately) to be laid in panels including curing complete as directed.

Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned let class timber, 25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles & rails made from hardwood timber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) (ii) 30mm thick

Providing, fitting and fixing anodised aluminium sliding MI s lows and ventilators of standard sections without horizontal ulazing bars, joints mitred and welded (manufactured to inInvant IS specifications) and providing and fixing handles, angle cleat, rub (a)2 Track sliding window (i)5 mm frosted glass

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and Corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) A) Tower bolts 150mmx10mm (c) Door handles (ii) 100 mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and Corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) C) Door handles ii) 100mm

Providing precast R.C.0 slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed. b) 75mm thick slab

m) I distempering two coats with oil bound distemper of oppmved brand and manufacture and of required shade on iiow w;tIl surface to give an even shade, over and including a Hulling coat with distemper primer of approved brooming the surface free from ilinitar dropings and other foreign matter and including 1,1t)pailng surface even and sand papered smooth.(i).Priming coat with distemper primer

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter , sand papering and knotting. (b). With ready mixed paint , wood primer (white).

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Painting Iwo coats (excluding priming coat) on new wood and Wood based surface with enamel paint of approved brand and Manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces Of all dirt, dust and other foreign matter sand papering and stopping.. (i).Surfaces over 100mm in width or girth. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Painting two coats (excluding priming coat) on new steel and Other metal surface with enamel paint of approved brand and MenUfacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Borger paint/ ICI paint/ J & N paint/ Nerolac).

Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately) Indian type W.C Orissa pattern of size 580 x 440 mm (a) White i) Parryware make

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make a) White (v) Elite S Trap (Cat No.C0297) (inclusive of seat cover)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) A) Parryware make a) White (ii) Deluxe Single Flush (Cat. No. C8091/C8057)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining,fitting and fixing wiyh clamps etc.as necessary completeat all levels including below GI as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining,fitting and fixing wiyh clamps etc.as necessary completeat all levels including below GI as directed and specified. a) In exposed surfaces or in trenches. (v) 60mm dia

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing PVC Plain single tee of (Supreme/ prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as (lauded and specified. a) In exposed surfaces or in trenches. iii) 110mm dia.

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making etc. Basin (without pedestal) (A) Parryware Make, white (i) Star Basin 550 x 400 (Cat. No.C0450)

Providing fitting and fixing stainless steel AISI 304 (18/8)Kitchen sink (610x535x230) of Parryware make as per IS 13983 with C.I. Brackets and 40 mm stainless steel plug including painting of fittings and brackets, cutting and making good the walls wherever required. (v) Single Bowl (210 x 180) Flat Edge - Glossy (Cat.No.C8543)

Providing fitting and fixing Mirror of Jaguar make ( Cat. No. VN¬9011) colour CP frame of complete as directed and specified.

Providing, fitting and fixing CP soap tray etc. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Construction of inspection pit inside measurement 450mm x450mm x 450mm flush with 100mm diameter HCl/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 etc.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple etc. (A) Exposed or in trenches c) 32 mm dia

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple etc. (d) 25 mm dia. I) Using Tata (medium)

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple etc. f) 15 mm dia

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (I) Essco make (a) Bib cock short body.

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (I) SONA make (a) Lig ht type

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex/ Polycon/Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes complete as directed. (A) 2000 litre capacity i)Sintex make

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. (i)Bore hole of 75mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of packing of pea gravel free from dirt, dust and other foreign materials ETC. (I) G.I. Pipe (a) TATA/ SAIL (medium) (sockets should be welded to the pipes) (i) 50mm diameter.

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed (II) PVC Pipe (a) Supreme Brand (iii) 40mm diameter.

Supplying fitting and fixing ribbed screen PVC filter 3.00 metre long.(a) 40mm Diamter

Supplying fitting and fixing check valve (non return valve) including thread to pipes c) (iii)40mm dia

unsheathed 1.1KV grade (R.R Keble/Finolex/Havells Make) as approved by this department single core copper conductor cable in Recessed PVC. conduit wiring system with 20 mm. dia , 2 mm thick rigid P.V.C. conduit including 6 Amps flush type switch (Anchor/Kolors Kany.com. Make), in iron clad switch board (I.S Imarked) with phenolic laminated sheetcover, ceiling rose etc complete. a) Short point upto 3.00 metre length

Wiring as in item no. 72 above in Recessed PVC. Conduit wiring system with 20 mm. dia, 2 mm thick, rigid P.V.C. Conduit to a Fan/exhaust Fan point including 6 Amps flush type (Anchor/Kolors Kany.com. Make) switch, ceiling rose I.0 switch board with phenolic laminated sheet cover as required complete b) Medium point upto 6.00 metre length

Wiring to a light point with 1.5 sq. mm PVC. insulated unsheathed 1 1KV grade (R.R Keble/Finolex/Havells Make) as approved by`this department single core copper conductor cable in Recessed PVC. conduit wiring system with 20 mm. dia., 2 mm thick rigid P.V.C. conduit including 6 Amps flush type switch (Anchor/Kolors Kany.com. Make), in iron clad switch board (I.S I. marked) with phenolic laminated sheet cover, ceiling rose etc.complete. c) Long point upto 10.00 metre length.

Wiring to a light point with 1.5 sq. mm PVC. insulated unsheathed 1 1KV. grade (R.R Keble/Finolex/Havells Make) as approved by this department single core copper conductor cable in Recessed PVC. conduit wiring system with 20 mm dia., 2 mm thick rigid P.V.C. conduit including 6 Amps flush type switch (Anchor/Kolors Kany.com. Make), in iron clad b) Medium point upto 6m length

Wiring as in item no 72 above in Recessed PVC. Conduit wiring system with 20 mm. dia, 2 mm thick, rigid P.V.C. Conduit to a Fan/exhaust Fan point including 6 Amps flush type (Anchor/Kolors Kany.com. Make) switch, ceiling rose I.0 switch board with phenolic laminated sheet cover as required completes) (C) Long point upto 10.00 metre length.

Wiring as in item no 72 above to a call belt point in Recessed P V.C. Conduit wiring system with 20 mm. Dia, 2.00 mm thick P.V.C. Conduit pipes. including I.C. switch board with phenolic laminated sheet cover, ceiling rose etc. b) Medium point upto 6.00 metre length

Wiring as in item no 65 when fixed on the same board In Recessed PVC. conduit wiring system on the recessed I.0 switch board

Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated unsheathed I.S.I. marked single core copper Conductor cable (R.R Kable/Finolex/Havells Make) in Recessed P.V.C. conduit Wiring system including providing and fixing 5 pin 16 (Anchor/Kolors Kany.com Make), I.C. switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm pin as required complete with 20 mm. dia, 2 mm thick rigid P.V.C. Conduit pipes. b) Medium point upto 6.00 metre length

Wiring for circuit wiring with P.V.C. insulated unsheathed 1.1 K.V. grade (I.S.I marked, R.R Kable/FinolexJHavells Make) single core copper conductor cable in Recessed PVC conduit wiring systema) With 2 x 1.5 sq. mm. P.V.C. insulated single core copper conductor cable in 20 mm dia, 2.0 mm thick rigid P.V.C. conduits.

Wiring for drawing sub-main line with P.V.C. insulated unsheathed 1.1 K.V. grade (1.S.1 marked, R.R Cable/Finolex/Havells Make) single core copper conductor cable in with earth continuity in Recessed PVC conduit wiring system a) With 2 x 2.5 sq. mm. + earth continuity with 1x2.5 sq. mm. PVC.insulated unsheathed single core copper conductor cable in 20 mm. dia., 2 mm thick Rigid P.V.C. Conduit pipes.

Wiring for drawing sub-main line with P.V.C. insulated unsheathed 1.1 K.V. grade (1.S.1 marked, R.R Cable/Finolex/Havells Make) single core copper conductor cable in with earth continuity in Recessed PVC conduit wiring system b) With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 20 mm. dia., 2 mm thick. Rigid P.V.C. Conduit pipes.

Wiring for drawing sub-main line with P.V.C. insulated unsheathed 1.1 K.V. grade (I.S.I marked, R.R Cable/Finolex/Havells Make) single core copper conductor cable in with earth continuity in Recessed PVC conduit wiring system c) With 2 x 6 sq. mm. + earth continuity with 1x4 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 20 mm. dia., 2 mm thick. Rigid P.V.C. Conduit pipes.

Wiring for drawing sub-main line in Recessed P.V.C. Conduit wiring system) With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

a) Installation of Earth station with 40 mm. dia. and 4.50 metre long G.I. pipe with necessary G.I. reducing socket 40 mm x 20 mm. size locking arrangement with h'inged cover plate, funnel, G.I. nuts, through bolts etc. for putting pipe and re-fitting with necessary enclosure on the top etc. as required complete.

(a) Supplying and laying 8 S.W.G. Copper wire at 0.50 metre below ground level for Conductor earth electrodes including soldering, excavation work and refilling etc. as required complete.

Supplying and fixing of Call bell ( Buzzer ) including 5/ 6 amp capacity button piano type bell push switch including connection as approved by the Deptt.)as required.

Supplying including fitting fixing of A.C. Exhaust fan in the existing hole on the wall of follwing sweeps and making necessary connections etc. as required complete and as directed by the Department. a) Domestic i) 225/230 mm sweep

Supplying with fitting and fixing 300 watt electronic modular fan speed controller including making necessary connection as per direction of department.

Supplying including fitting fixing of high speed A.G. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connections etc. as required complete and as directed by the Department [Without regulator].a) 1400 mm sweep

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Double door surface mounting SPN MCB DB (IP-43 protection)incorporated. with bas-bar, neutral link, earth bar and Din rail etc. fitted on wall with grouting nuts & bolts as regd. c) 8 way TPN (4+24)

Supplying with fitting and fixing MCCB incomer and MCB outgoing sheet steel, phosphatised, powder painted double door surface mounting vertical TPN MCB DB (IP-43 protection) incorporated with bas-bar, neutral link, earth bar and Din rail etc. fitted on wall with grounting nuts & bolts as regd. complete with making necessary connection as specified and directed by the deptt.a) 4 way TPN (4+12), 16 KA, double door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Hagger make] A. B Series 1. Single Pole 10 KA 240 //415 50 Hz MCB [a] 6A

Supplying with fitting and fixing SPN 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Nagger make] 1.SPN 10 KA 240 //415 50 Hz MCB [f] 40A

Supplying with fitting and fixing 4 Pole 10 KA 415V 50Hz MCB Conform to IS/IEC 60898-1:2002 of the following capacity complete with making necessary connection as specified and directed by the deptt. 40A

Supplying with fitting and fixing 4 Pole 10 KA 415V 50Hz MCB Conform to IS/IEC 60898-1:2002 of the following capacity complete with making necessary connection as specified and directed by the deptt. 63A

Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=lcu, adustable Ir setting 0.7- 1) (without enclosure) of the following capacity complete with Making necessary connection as specified and directed by the deptt. 63A

Supplying including installation, commissioning of vermin and dust proof (IP-43 protection) totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 M (B) x 1.20 M (H) x 0.40M (0) made of 16 SWG (1.66MM) thick C.R. sheet and 30mm x 30mmx5mm size angle having 4 nos legs at the bottom and C.R. sheet roofing on the top complete painting with 2 coats of Red Oxide metal primer and 2 coats of Enamel paint. The panel board is to be errected in 1 :3:6 PCC foundation including excavation of trench and brick soling etc. complete neatly wiring done with provision for one no 4 pole MCCB as incomer and provision for 6 nos DP or 4 Nos TPN out going as specified and directed by the deptt.comprising of the fbllowing electrical items:i] 125A 4 pole 25 KA AC 415V MCCB (Ics=lcu, adustable Ir setting 0.7-1) as incomer - ii] 20mm x 3mm 4 strip copper Bus-Bar 0.6 M length each

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar up to 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 8 way TPN (4+24) single door

Supplying, installation, testing and commissioning of the TL5 Flourescent luminaries complete with all such as ballast, staeter etc. directly on wall / ceiling including connection with 1.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. d) VECTOR 28W TCH2O7 1xTL528W(Bright & Elegant • 45% energy saving as compared to 40w conventional batten.• High Power factor (PF>.98) batten. • 3D Batwing Design channel, enhances light output.• Warm start operation, helps in extra long life.• Stop Circuit — Additional safety feature

upplying and fixing brass batten holder including connections etc. complete (without shades & bulbs)

Supplying and fitting of 18/20 watt CFL lamp in the existing brass batten holder/angle holder/decorative bracket/bulk head fitting etc. as specified and directed by the Department

Supply and laying of following size PVC/XLPE.insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured UG. cable laid in ground/partially in air (10.0% of cable length) including excavation af cable trench upto depth of 75cm, refilling, protective brick covering, sand cushioning etc. complete handling of surplus spoil, debries etc. to proper place as specified and directed by the deptt. 50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply.and laying of following size PVCIXLPE insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured U.G. cable laid in pucca flooring road crossing, drain crossing Amil partially in air through G.I. Pipe (TataiNezone make) with necy bend and socket including excavation and refilling the treance and making good damange done as specified and directed by the deptt. c) 50.00 mm2 3&1/2core U.G. Cable in C) 50mm dia medium quality G.I. Pipe .

Supplying installation and commissioning of vermin and dust proof totally enclosed single door cubuical type compartmental floor mounting Metering Cabinet of size 1.00 m x1.00 m x0.50 m node of 16 SWG (1.66mm) thick CR sheet and 35 mm x 35 mm 6 mm size angle and 35 mm x6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly intemal wiring done as specified and directed by the department comprising of the following electrical items. (UPTO 125 AMP)(MCCB incomer and meter will be be measured and paid seperately). 1. 25 mm x 5 mm size 4 strip copper Bus-Bar- 1 set

Supplying including fitting & Fixing of water supply motor pumpset ( with Single Stage Horizontal Jet Pump) motor 2800 RPM complete with pressure regulator valve fixed on C.C. foundation of Proportion 1:2:4 jammed with M.S. Nuts and Bolts including D.O.L. Starter and making necessary connection etc. as regd. complete. 1 H.P. Single Phase

J.D.Enterprise