REPAIRS TO ROOF, SUNKEN TREATMENT, FLOORING AND OTHER MISC B AND R WORKS AT JCOs, ORs MD ACCN IN FAFA, A AND E REGT AND AUTO REGT UNDER AGE B AND R - II UNDER GE (N) AHMEDNAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Demolition of reinforced cement concrete of any descriptions and in any position etc complete all as specified and directed.

M&L for RCC Type B-1 1:2:4 using 20 mm graded aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and floor slab.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering complete all as specified and directed

M & L hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. Complete all as specified and directed.

M/L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed.

M&L for coloured glazed ceramic tiles digitally printed 300x450mm,7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 8-10 mm thick as approved by GE (square / rectangular) area of each tile 600x600mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

All as per item No 10 but as in dado/skirting on vertical surfaces over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L for Virified Ceramic tiles dark shed/Double Charged/ultrachared 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. laid over and including roughning existing surface, making good the damaged surface, levelling and fixing with cement based tile adhesive (make FOSROC, DR FIXIT) as per the manufacture's instructions and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and as directed by Engr-in-Charge.

All as per item No 12 but as in dado/skirting on vertyical surfaces over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

Material and labour for joint free /rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free anti skid ceramic coloured tiles 300x300mm 7-8mm thick matching to dado tiles area of each tile, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick Screed bed etc complete all as specified and directed by Engineer-in-Charge

M&L for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc including dismantling complete all as specified and directed by Engineer-in-Charge

Material and Labour for 75mm thick plain cement concrete type C-1 (1:3:6) using 20 mm graded stone aggregate as in plinth protections & path, complete all as specified

M&L for 30mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 ® in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete including dismantling all as specified and directed

Fixing only for 30mm thick rough dressed lime stone slab (shahabad) flooring, laid dry, jointed and pointed in cement mortar 1:6 and pointed in cement mortar 1:3 ® in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed

Dismantling of unframed work timber scantling 40 Sq, Cm and over in section, in any position

Dismantling of unframed work fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

Dismantling of asbestos cement, corrugated or semi corrugated sheets in roofing

M & L for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as directed

M&L for Asbestos cement two piece serrated ridge for corrugated sheets fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as directed

Fixing only 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as directed

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness complete all as directed

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof fixed with self tapping screws complete all as specified, colour and design as approved by GE including dismantling of plain steel sheeting, any gauge, thickness.

S&F for false ceiling with Vinyl faced Arm-Gyp-FB, ceiling 600 x 600 x 9mm thick with washable metalized polyester foil backing with Vinyl covered edges, supporting sections shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre as per manufacturer's instructions / specification and all as directed including taking down/ out existing.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site.including 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, cover fillets,including dismantling boarding, any description, fixed in any position with nails

S&F of Steel work in tubular trusses, Perlin, rafhter, including special shaped washer etc. complete conforming to I. S.1161-1979 grade St.-240

S&F of steel work in post, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. as per Fe 410 -W (Gde- E- 250) quality- A

Material and labour for providing water proofing treatment on roofs, as per manufacturer's instructions and as specified after taking down/out as existing tar felt at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqm and allow to dry. (b) Applying and laying torch APP polymer modified bituminous membrane 3 mm thick with non woven polyester mat as reinforced weighing not less than 3 kg/sqm by thermo fusion process as per manufacturers specification (c) Applying one coat of aluminium paint on APP polymer modified bituminous membrane.

M&L for rendering 10 mm thick in CM 1:3 by using 100% coarse sand on roof mixed with & including WPC @ 3% by weight of cement and finished the surfaces even and smooth without using extra cement.

S&F 110mm bore PVC rain water pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc including taking down of any type complete all as specifed and directed.

S&F Rain water pipe 110mm dia Pvc (SWR) single mm dia Pvc (SWR) bend any radius, completed as specified and directed.

S&F bands, straps, supports or stays for rain waterpipes, hooks (stay) heavy for large gates, hook and pintle hinges clamps, hold fasts wall ties, hooks for hanging fans and similar small articles Fe-290 Gde- E-165 or Fe-310-0 complete all as specifed and directed.

Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified

M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius, modular bricks built in CM 1: 6 complete all as specified

Raking out cement mortar joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses etc complete all as directed.

M&L for Pointing to random rubble or polygonal rubble uncoursed or brought up to courses in CM 1:4 etc complete all as directed.

Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed

M&L for rendering, 10 mm thick on brick / concrete surfaces in cement mortar 1:6 surfaces finished even and smooth without using extra cement including sagol finished complete all as specified.

M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffholding etc complete all as directed.

M & L for preparation of newly plastered surface of wall and apply three coats of white wash any height including scaffholding etc complete all as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats for cement based paint overv a coat of alkali resistant priming paint any height including scaffholding etc complete all as directed.

M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffholding etc complete all as directed.

M & L for preparation of old plastered surface of wall and applying one coats of cement base paint any height including scaffholding etc complete all as directed.

M&L for preparation of old plastered or unplastered surfaces of walls including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying one coat of white lime wash at any height including scaffholding etc complete all as specified and directed by Engineer-in-charge.

All as per item No 54 (here-in-before) but on ceiling.

M & L for preparing old plastered surfaces of walls and apply one coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffholding etc complete all as specified and directed

M&L for preparation of old plastered treated surfaces of walls by brooming down and and applying one coat of weather proof 100 % acrylic exterior emulsion apex ultima paint of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M&L for 2 mm thick wall care putty etc complete all as specified and directed

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide.

S&F fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge

S&F fix in repairs wash hand basin with pedestal vitreous China white , flat back or angle type of size 550 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device etc complete all as specified and directed by Engineer-in-Charge connecting to 'P' or 'S' trap etc complete all as specified and directed by Engineer-in-Charge.

S & F in repairs looking mirror of size 600 mm x 450 mm etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections

Ditto all as per item No 67 above but 20 mm bore tubing

Ditto all as per item No 67 above but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Ditto all as per item No 70 above but 20 mm bore tubing

Ditto all as per item No 70 above but 25 mm bore tubing

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs stop cock/ anglecock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs twin(Two way) bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

S&F in repair PTMT bib tap 15 mm dia, screwed for iron pipe complete all as specified and directed.(Minimum weight 15mm-90Gms)

S & F in repairs PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified.

M&L for Chromium plated Towel Ring fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps etc complete all as specifed and directed.

.-Ditto- but As in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps etc complete all as specifed and directed.

.-Ditto- but As in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 75mm bore

M&L for special treatment to sunken slab floor (Area of Sunken Portion n exc 1.50 Sqm) incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

M&L for special treatment to sunken slab floor (bottam and vertical portion) etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected including dismantling water tanks and removing to store complete all as directed.

All as per item No. 95 above but 1000 ltr capacity

All as per item No. 95 above but 2000 ltr capacity

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball and high density plastic ball screwed to iron pipe, tank nipple and connected (Minimum weight 15mm-142Gms/20mm-210Gms) complete all as directed.

S&F in repair 25mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball and high density plastic ball screwed to iron pipe, tank nipple and connected (Minimum weight 15mm-142Gms/20mm-210Gms) complete all as directed.

M&L for 25 mm Mild steel Chromium plated curtain rods with end brakets and fixing stand/globe of choice, of same material, haevy duty all as directed by engineer in charge

Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description n exc 1 Sqm each etc complete all as specified and directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S & F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

S&F for factory made 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc all as specified

M&L for factory made 35 mm thick IInd C/L H/W plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M&L for 0.9 mm thick decorative laminate type 1 on Flush door surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing.

M&L 18mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work.

S&F frame 50 x 100 mm WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Butt hinges and necessary S S screws shall be paid separately)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain cup board shutter of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Butt hinges and necessary S S screws shall be paid separately)

S & F 30mm width of flaps continuous (piano) hinges, mild steel, bright finish or electrogalvanised

S&F powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge

S&F anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&f Steel ventilator with top hung shutter including hinges, steel peg stay, complete

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S & F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

S&F butt hinges medium weight cold rolled mils steel 100mm long.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long.

S&F aluminium anodised handle of extruded section 150mm long.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long.

S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

Hacking out old broken glass ( any thickness size ,quality or description ) from wooden/Steel frames glazed with putty or fixed with beads.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads, rubber beding in squares exc 0.50 sqm in each pane

M & L for 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for 4 mm thick plain sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads, rubber bedding in squares n.exc 0.50 sqm in each pane.

M & L for 5.5 mm thick tinted sheet glass ordinary quality and glazing with oil putty or wooden beads in squares .exc 0.50 sqm in each pane.

M & L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M & L for preparation of old wooden surface and applying one coat of synthetic enamel paint.

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmetc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair fancy type brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by engineer-in-charge.

S&F in repair Aluminium body door closer for aluminium door shutter hydraulically regulated,designation No 1 universal type,suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixed.

M&L in repairs spouts of 75mm dia including jointing to waste pipe fixed in cement concrete type (1:2:4) type B1 using graded stone aggregate including removing old spouts etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC Type C-1 1:3:6 using 20 mm graded aggregates as in edges of floor tiles/blocks roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for 60 mm thick, PCC pavers interlocking tiles of glossy finish, with grey cement and no pigment ,any shape & size conforming to IS 15658 of 2006. M-35 grade made up with 12.5mm graded mechanically crushed stone aggregates, factory made over and incl 30mm thick sand cushioning and joints filled with fine sand incl leveled with plate vibrator & sweeping etc complete all as specified and directed.

Material and labour for Digitally printed paver tiles 30cm x 30cm x 10mm thick, approved by GE withnset, jointed and pointed in neat cement slurry with grey cement and pigment to match in floors ,over and including screed bed or bedding a layer of 15 mm th cement mortar 1:6 complete all as specified and directed

S & F in repairs steel Soap dish icluding necessary fitting material Scews etc complete all as specified.

S&F Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.5 sqm area fixed with and including one number SS clamps (grade -202) of flat-30mm X2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener,polishing, rubbing & including silicon treatment at height more than 6 mtr complete all as specified.

S&F Vitreous China urinal, Half stall type, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe andwaste pipe)

S&F in repair wall mounted cloth drying stand consisting of 16 mm dia powder coated MS rods of CR steel mounted on powder coated MS square pipe, 16- 4 rods, 4ft each, total weight not less than 3.80 Kg, fixed to wall including all fittings/accessories etc complete all as specified and directed by Engineer-in-charge Make -Easy dry Model: Mount it or Equivalent product in Nirali/Prayag.

M/S-B.R.SONAWANE

Ms. M.D. Auty

MATOSHREE CONSTRUCTION

M/S. YADAV ENTERPRISES

Avinash B Kullal

OM SAI ASSOCIATES

M/S. M. F. Sharif & Co.

MS. G.A. CONSTRUCTION

AMAR CONSTRUCTION