REPAIR/ REPLACEMENT TO JOINERY, FLOORING, SANITATION AREA, ROLLING SHUTTERS, ANTI TERMITE TREATMENT, WATERPROOFING TREATMENT, REHABILITATION OF DISTRESSED CONCRETE MEMBERS AND OTHER CONNECTED ITEMS IN RESIDENTION AREA AT MO (MB) GHATKOPAR UNDER GE (

Amount

Taking down chowkat or frame with shutter (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames), exc 1.50 sqm but not exc 4.0 sqm each complete as specified and directed.

Taking down shutters of any description but exc 1 Sqm and n exc 2.00 Sqm complete as specified and directed.

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core both faces panel covered with decorative face veneer with lipping complete as specified and directed.

S&F for 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F wire mesh shall be measured and paid for separately)

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

S&F for Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

S&F for Factory made solid PVC Moulded door shutter , 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm th. Moulded PVC sheet on the front face & 2mm plain coour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with wood free EPS etc, complete all as specified and as directed.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples in m s window / wooden shutter complete all as specified and directed

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F stainless steel butt hinges, 100mm, medium weight complete all as specified and directed

Supply and fix extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section of size 150mm complete all as specified and directed.

S&F 250mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete as specified and directed.

S& F in repair door closer hydraulically regulated Aluminium (extruded section body), designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete as specified and directed.

M & L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as spd and as directed

S&F in repair 300mm, ordinary rat tail rod pattern springs includding roller and roller platewith fixed to wooden/pressed steel frame chowkats with flat iron 40x3mm size 75 cm long with necessary bolts, etc. complete as specified and directed.

Supply only 4.80mm thick ordinary quality plain glass not exc 0.5 Sqm each pane with including wooden/rubber beading or gasket for aluminium section complete all as specified.

S&F for 18 mm thick termite resistant and water proof, both side prelaminated wooden plywood one side with decorative choice lamination, and other side plain white lamination total thickness not more than 22 mm thick, as in cup board shutters & frame , including piano hinges, wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, with complete as specified and directed. Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) Thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The lamination shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets . 3) Frame to be fixed to walls, soffits & base of cupboard with fasterners

S&F for 12 mm thick termite resistant and water proof , both side laminated wooden plywood one side with decorative choice lamination & other side plain white lamination , total thickness not more than 15 mm , as in cupboard shelves & partitions including fixing to wall, soffits & base of cupboard by powder coated aluminium cleat (colour of powder coated to match colour / shade of laminate) also including PVC lipping on all exposed edges of same texture & shade to match the laminate complete as specified and directed. Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) Thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid

S & F 25mm thick, block board grade 2 quality interior grade decorative type with decorative face veneer on both face fixed as in shutters complete as specified and directed.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete as specified and directed.

S&F in repairs 40mm dia and 75mm long, extrruded fancy type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts , screw and washer of mild steel bright finished ,complete as specified and directed.

S & F in repair 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in door

S&F in repair stainless steel butt hinges, 100mm, medium weight complete all as specified and directed

Supply and fix in repair extruded aluminium alloy handles, fabricated type of size 150mm in any position complete all as specified and directed.

S&F in repair aluminium, anodised, barrel tower bolts of extruded section of size 150mm complete all as specified and directed.

S&F in repair 250mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete as specified and directed.

Hacking out old, broken glass (any thickness,) size quality or description) from metal frames incl.punching or drilling out old glazing pins/spring clips and fixing new ones incl M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

S&F standard aluminum section powder coated in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed. Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S&F aluminum anodised grill DG- 202 ( 10 mm x 8mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etc complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc out side MD land complete all as specified and directed.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.06 sqm n exc 0.11 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 laying floor finished complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x200mmx7mm thick in vertical surfaces such as skirting/dado and risers to steps and including over 10mm thick rendering in CM 1:3 on fair faces of brick/concrete surfaces as in backing coat for tiles. etc, complete as specified and directed.

M & L 9 to 10 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for vertified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed.

M&L for vertified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in vertical surfaces such as skirtings, dados etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles.complete all as specified and directed.

Demolition of concrete in ground floors (un re-inforced) and paving n.exc. 15 cm thickness (below or above ground level) and removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

M&L for 100mm thick cement concrete type B-1 1:2:4 using 20mm graded stone aggregate in flooring finishes the surfaces even and smooth without using extra cement etc complete all as pecified and directed.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope including making rounded or chamfered on edges mixed with WPC @2% by weight of cement, complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm. (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%.

S&F machine cut and machine polished, green marble, 18-20mm thick on horizontal or vertical surface,as in window cills and jambs bedded, jointed and pointed with neat grey cement slurry and pointed with coloured or white cement with pigment to match over and including rendering coat of 10 mm thick in CM 1:4 complete as specified and directed.

M&L for 75 mm thick cement concrete Type C-1,1:3:6 (20 mm graded aggregate) as in plinth protection finishes and fair without using extra cement including forming 12 mm thick expansion joint filled with sealing compound Grade 'A' etc complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

Cutting and grooving of wall for fixing of pipe lines and after fixing of GI pipe line and making good of all cutting surfaces complete as specified and directed.

S&F 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed.

S&F 20mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed.

S&F in repairs for 20mm dia fancy type chromium plated curtain rods with fixing fancy brackets, brass screws etc complete all as specified and directed

S&Fin repair plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete all as specified and directed..

S&F in repair brass chromium plated towel rail 20mm dia 'D' type 600mm long between flanges, of with and including chromium plated brass screws etc complete all as specified and directed.

S&Fin repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and seat cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

S&F in repairs vitreous china squatting pan, white, orissa pattern pan of size 580 mm x 440 mm of standard quality with integral foot rests,and including 'P' trap or 'S' Trap complete including connection to trap and to flushing pipe, anti syphonic pipe etc., complete all as specifiedand directed.

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm , 32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC etc, complete all as specified and directed.

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

S/F in repairs brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type complete all as specified and directed.

S & F in repairs Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, with brackets complete all as specified and directed .

S & F in repair 160mm bore PVC rain water pipe single socketed any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc including taking down and filling nail holes on the walls to prevent seepage and making good complete all as specifed and directed.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 160mm bore PVC (SWR) bends any radius dimnishing pieces or tapers etc, complete all as specified and as directed.

S&F in 110 mm bore PVC (SWR) tee of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

Demolition of brick work or stone boulder masonry,built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles.complete all as specifed and directed

M&L for brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specifed and directed

Taking down cement or cement lime plaster of any description on brick or stone wall and ceiling surface including raking out joints, hacking for key, scrubbing down with water etc and disposing off the rubbish outside MD land complete all as specified and directed.

M & L for rendering 12 mm thick in CM 1:6 on brick walls or concrete surfaces and finishing the surfaces even and smooth with sagol finish complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:3 on concrete surfaces as in ceiling and finishing the surfaces even and smooth complete all as specified and directed.

M/L for 15mm thick rendering(two layer) in CM 1:4 on external surface of wall mixed with water proofing compound and shall be scored to provide key for rough finishing coat. including necessary scaffoldings etc complete all as specified and directed Note:- WPC shall be measured and paid seperately.

Supply only integral water proofing compound.

M&L for preparation of new plastered surfaces on walls, chajjas,filling of hair line cracks with white cement and applying two coats of 100% anti fungal weather resistant acrylic paint over a coat of acrylic primer in approved shade and as per manufacturer's instructions including necessary scaffolding complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and two coats of oil bound distemper over a coat of Birla putty complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered or unplastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying with roller one coat of oil bound distemper including application of putty for smooth finish.etc complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, not other wise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old decorated steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. Note :- Height of structure exc 10 mtr

M&L for preparation of old acrylic surfaces of walls/ceiling including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots, washing down with water, filling of cracks with Dr fixit crack filler or equivalent make and applying one coat of 100% antifungal acrylic weather proof paint of approved shade including necessary scaffolding work etc complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and thereafter applying with roller one coat of plastic emulsion paint including application of Putty for smooth finish.etc complete all as specified and directed.

S&F in repair 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

S&F in repairs 500 ltrs Rotational mould polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in ssr part-I complete all as specified and directed

S&F in repairs 1000 ltrs Rotational mould polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in ssr part-I complete all as specified and directed

M&L for post construction anti- termite treatment along the external wall below concrete or masonary apron using chemical emulsion @2.25 liters per linear meter including drilling and plugging holes with cement morter 1:2 to match the existng floor etc complete all as specified and directed.

M & L for post construction anti - termit treatment at points of contact of wood work using chemical emulision (in oil or kerosin based solution ) @ 0.5 liters per holy by drilling 6 mm dia holes at a down ward angles of 45 degree at 150 mm centere to center and sealing the same with white cement and making good to the existing surfaces etc complete all as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor soil complete as specified and directed.

Dismantling of ceiling board (fibre, pulp,insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed.

M & L for false ceiling of galvanised iron frame work of angle section of 15 x 15 x 28 gauge for support and main U section of 40 x 20 x 26 Gauge and supporting U clip of 32 x 18 x 26 Gauge and gypsum board of 12 mm thick in panels fixed to GI frame work including cutting, bolting, welding etc of GI frame work and joints filled and finished with POP and applying two coats of oil bound distemper over coat of alkali resistant primer with roller etc complete all as specified and directed.

Taking down aluminum door shutter carefully and refixing the same in position replacing rubber bead, worn-out door closer mortice lock and replacing existing broken aluminium section / glass / wire cloth / Bakelite sheet, if any and making door shutter serviceable, for work complete all as specified and directed. Note - Aluminum Section / Glass / wire cloth / Bakelite sheet, shall be measured and paid separately as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

Taking down aluminum window shutter carefully and refixing the same in position replacing rubber bead, worn-out handles and replacing existing broken Aluminum section / glass/wire cloth/backlite sheet, if any, and making window shutter serviceable, complete all as specified and directed. Note - Aluminum section / Glass / wire cloth / Bakelite sheet, handle etc shall be measured and paid separately as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Routine maitenance of rolling shutter of following sizes the maintenance including the following all as specified and directed. (a) Taking down hood covers for carrying out routine maintenance and refixing. (b) Dismantling the MS and CI works of any description such as sheets, shafts, cost iron wheels lath etc and taking down helical springs, rollers and other accessories etc. (c) Refixing the unserviceable accessories such as shafts, helical springs, rollers lath sheets, cast iron wheels etc. (d) Replacement of the unserviceable accessories such as shaft helical spring, rollers, MS lsth sheets hood covers, cast iron wheels including drilling, welding etc complete. (e) Cleaning, oiling, greasing etc complete of all movable parts all as required at site( Note- The parts and accessories to be replaced shall be measured and paid seperetely ) (A) Area of shutter n.exc 5.00 sqm maximum size 1.80mx2.40m

All as per iteme No.98 but for area of shutter exc 5.00 sqm but n.exc 10.00 sqm (maximum size 3.20m in height)

All as per iteme No.98 but for Area of shutter exc 10.00 sqm but n.exc 20.00 sqm (maximum size 5.15m in height)

All as per iteme No.98 but for Area of shutter exc 20.00 sqm but n.exc 40.00 sqm (maximum size 6.77m)

Supply only mild steel lock plate 150mm width 3.15mm thickness reinforced with MS angle of 35x35x5 mm at bottom including pulling handle sliding bolt etc complete all as specified and directed.

Supply only mild steel gear box including gear wheels of rolling shutter machine cut with MS shaft 25mm bore heavy grade complete all as specified and dircted.

Supply only MS roller of 50mm to 60mm dia including nuts bolts etc all as specified and directed.

Supply only MS roller of 65mm to 75mm dia including nuts bolts etc all as specified and directed.

Supply only MS accessories for rolling shutter repair such as shafts helical springs pully, lath sheets, cast iron wheels etc all as specified and directed.

M&L for preparation of new steel surfaces and applying two coat of aluminium paint over a coat of red oxide etc complete all as specified nd directed.

M&L for preparation of old steel surfaces and applying one coat of aluminium paint etc complete all as specified and directed.

S & F in repair Steel rolling shutter ( thickness of lath 1.25mm thick) without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated and including taking down of any thickness etc, complete push pull or manual type etc complete all as specified and directed.

Deduct Credit for Demolished/ Dismantled material Rs. (-) 34700.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

S K ENTERPRISES

S R INFRASTRUCTURE

M/s Qureshi Construction Co

industrial suppliers

M/S VISHRANTA CONSTRUCTION

Parmatma Enterprises