8871/E8

Amount

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section in any position (framed work) complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and as directed.

Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for 15 mm thick Rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smoth without using extra cement using water proofing compound by weight of cement as per manufacturer's instruction (WPC measured and paid sperately).

Supply only integral water proofing compound conforming to IS-2465-1975 complete.

M&L rendering 15 mm thick in CM 1:6 on brick/ concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed .

M&L preparation of newly plastered surfaces of work and applying two coats of cement base paint all as specified and directed.

M&L preparation of old untreated surfaces of work and applying two coats of cement base paint all as specified and directed.

M&L preparing old surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L preparing new surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L MS in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tube conforming to IS 1161 -1979 grade St -240 complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and directed.

S&F galvanised iron snap grid frame work made from galvanised iron main /cross tee of size 38 mm x 24 mm x 0.32 mm weighing 0.28Kg/RM and 28 mm x 24 mm x 0.30 mm weighing 0.22 Kg/RM respectively for false ceiling of grid size 600 mm x 600 mm including necessary hanging arrangement comprising of 4 mm dia MS rod, 'J' bolts with necessary bolts, nuts and washer all as per manufacturer's instruction complete all as specified and as directed. The snap grid (main & cross section) shall supported at ends all along the wall with galvanised iron angle of size 22 mm x 22 mm x 0.40 mm weighing 0.15 Kg/RM complete as per manufacturer's instruction and as specified and directed.

M&L for providing pre painted fiber cement board 4mm thick in ceiling fixed on GI snap grid as per manufacturer's instruction complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed.

M&L cutting holes in brick walls built in cement mortar for inserting holdfast and making good the dismantled portion in cement 1:3 or cement concrete 1:2:4 type B-1 all as specified and as directed depth of embeded portion of holdfasts or lugs measured from the face of the Jamb into wall exc. half brick but not exc. one brick.

S&F 2nd class hardwood plain solid, straight chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified in and directed.

S&F 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as directed.

S&F factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003(Part - I) kiln seasoned and chemically pressure treated (35 mm thick with 2nd class HW rail and style) complete all as specified and directed.

S&F mild steel flat iron as in hold fast for door window frames or chowkat etc. cut to length or drilled hole and fixed with screw etc. complete all as directed grade of steel conforming to Fe-410, Gde-E-165

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed.

S&F MS butt hinges medium weight cold rolled of size 100 mm complete all as specified and as directed .

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed .

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads area exceeding 1.5 sqm complete all as specified and directed.

S&F sheet glass 4.00 mm thick ordinary quality and glazing with oil putty or wooden beads in square, rectangle n.exc 0.5 Sqm in each pan all as specified and as directed.

M&L cement concrete 1:2:4 Type B2 (using 40 mm graded crushed stone aggregate) as in walls or retaining walls, any thicknes, size or shape including pilastres, butresses column, pillars, boundry pillars and posts(including caps and bases) complete all as specified and directed.

S&F stainless steel sink made out of 1 mm thick sheet for kitchen or laboratory, with plug washers and waste coupling including fixed with cantilever brackets and connecting union to pipe overall size 485 mm x 410 mm, bowl size 410 mm x 355 mm x 165 mm complete all as specified and directed . ( Make Nirali, Popular Range, Model name- Grace Plain small, glossy finish or equivalent)

S&F sheet glass assembly consisting of 5.5 mm thick sheet glass shelf, 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F 15 mm bib tap, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed . (Make : Jaquar model no CON-037KN or equivalent in Marc / Cera / Kohler)

S&F 15 mm dia steel water tube medium grade galvanised with all fittings and fixed complete to walls complete all as specified and directed.

Supplying and laying of 50mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 including all necessary bends and tees and other fittings fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed .

Taking out copper/aluminium point wiring cable from existing concealed conduit point wiring (light, fan, socket or power) complete, including fixture such as switches, ceiling roses, pendants, regulators, sockets, etc. removing materials from site and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed. (Note:- Disturbed surfaces of wall shall be make good by applying two coats of OBD over a coat of wall care putty over cement mortar plaster (1:3) where necessary to match with existing surface finish)

M&L point wiring with 1.5 Sqmm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable 1100 Volts grade drawn through with and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) PVC insulated, unsheathed, stranded, single core HRFR / FRLS copper cable as earth continuity wire connecting to common earth point including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC / Plastic laminated sheet. top cover, suitable sizes of brass screws and washers etc. for mounting switches, sockets, regulators etc complete for one light point / ceiling fan point / exhaust fan point / call bell point controlled by one way switches complete all as specified and directed. Note: Wiring wire color code i.e. Red/ Yellow /Blue for Phase, black for neutral and Green for earth shall be maintained.

All as per item no.41 above but for one three pin 5 Amp socket outlet on same board.

All as per item no.41 above but for one three pin 5 Amp socket outlet on independent board.

M&L point wiring with 2.5 Sqmm (nominal area), PVC insulated, stranded single core unsheathed FRLS copper conductor cable 1100 Volts grade drawn through with and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) PVC insulated, unsheathed, stranded, single core HRFR / FRLS copper cable as earth continuity wire connecting to common earth point including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC / Plastic laminated sheet. top cover, suitable sizes of brass screws and washers etc. for mounting switches, sockets, regulators etc complete for 3 pin socket outlet 15 Amps on independant board complete all as specified and directed. Note: Wiring wire color code i.e. Red/ Yellow /Blue for Phase, black for neutral and Green for earth shall be maintained.

Taking down carefully by unscrewing from boards/ outlet boxes switch, socket, ceiling rose, lamp holder call bell, fan regulator, bell push, cover plate, S/S any type etc complete all as specified and as directed.

S & F switch piano, flush type, 5/6 Amps, 240 Volts, single pole, one way, conforming to IS complete all as specified and as directed.

M & L Ceiling rose, surface type polycarbonate/ PVC three terminals, conforming to IS, complete all as specified and as directed.

S & F Switch socket combination 5 Pin, 16/6 Amps, flush type, multipurpose, conforming to IS complete all as specified and as directed.

S & F Switch socket combination 5 Pin, 6 Amps, 240 Volts, flush type multi-purpose, conforming to IS complete all as specified and as directed.

S&F socket outlet 3/5 pin 5 Amps flush type complete all as specified and as directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and as directed.

M&L call bell ding dong single pole complete all as specified and as directed.

S&F bell push flush type, 5 Amps 230 Volts complete all as specified and as directed.

M&L Sub main wiring with two runs of 6.0 sqmm (Nominal area) single core PVC insulated stranded unsheathed FRLS copper conductor cable upto and including 1100 V grade drawn through and including rigid PVC non mettalic surface conduit medium duty with conduit accesseries such as junction boxes, bends, tees etc. complete including one run of 4.0 sqmm (nominal area) single core, PVC insulated stranded unsheathed FRLS copper conductor as earth wire and duly connected to common earth point complete all as specified and directed including taking down old one. (Note :-(i) One run of PVC conduit, Two runs of 6.0 sqmm single core cable, one run of 4.0 sqmm earth continuity wire to be measured as one length). (ii) Chase cutting for replacement of defective/ unserviceable concealing conduit by new conduit if ordered, shall be measured & Paid separately under respective item in this schedule.).

Supply and fix sheet steel enclosure SPN DBs, 8 way, double door for MCBs with 200 Amps rated bus bar complete all as specified and directed including taking down old one. ( Make Legrand cat No 5076 11 or equivalent equiv in Schneider /GE)

Supply and fix MCB SP 240V, 6-32 Amps capacity including taking down old one complete all as specified and directed. (Make : Legrand cat No 4085 87-95 or equivalent in Schneider/GE )

Supply and fix MCB SPN 240V, 6-32 Amps capacity including taking down old one complete all as specified and directed. (Make : Legrand cat No 4086 17 or equivalent in Schneider/GE )

S & F LED Batten light 2ft 10 watt with extruded synthetic housing,3" X3" PVC block 2 Nos,Lamps,driver,connector etc incl hanging arrangement with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting through suitable size flexible PVC pipe making good to wall for old fitting ciomplete all as specified and directed including taking down old one. Make: CG cat no. LCTLN-10-CDL or equivalent in Bajaj/Philips)

S & F LED Batten light 4ft 20 watt with extruded synthetic housing,3" X3" PVC block 2 Nos,Lamps,driver,connector etc incl hanging arrangement with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting through suitable size flexible PVC pipe making good to wall for old fitting ciomplete all as specified and directed including taking down old one. Make: CG cat no. CCS-100-20-65-HL2-DP-NWH or equivalent in Bajaj/Philips)

M&L for LED light luminaire 20Watt, IP protection 66, complete including taking down old unserviceable fitting all as specified and directed.Make : Crompton Greaves Cat No : LSTS-20-CDL-M or equivalent in Philips/Havells/Bajaj.

Supply and fix GI Bracket made of 25mm dia MS pipe medium grade 1.5mtr long suitable for buildingsecurity light for building protection as per site requirement including suitable nut,bolt and clamps complete accesseries all as specified and directed and taking out old one.

M & L earthing complete with galvanised steel earth plate electrode 600X600X6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with the top edge of earth plate at depth not less than 1.5m below ground level connected with 4mm dia GI wire by means of bolts washers and protected by 15mm bore, medium grade GI pipe, funnel with 20mm bore GI medium grade watering pipe, wire mesh, copper lugs including concrete pit in PCC 1:3:6 type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350X350X50 mm, reinforced with 8mm dia deformed bars @15 cm C/C both direction and 10mm MS handle of suitable size, charcoal or coke and salt in alternate layers, necessary earth work in soft/loose soil, all as shown in Electrical Plate No 3 of MES Schedule Part-I and testing, complete all as specified and as directed.

M & L for dismantling burnt winding of ceiling fan (any size/ sweep/make) and taking out existing winding wire, and rewinding the same after proper cleaning with super enamelled copper winding wire as per existing gauge and turn to achieve the required RPM, cleaning/ replacement of bearings, bushes capacitor etc as required and testing complete for fan of old model requirement of super enamelled winding wire n.exc. 500 grms complete all as specified and directed.

Taking down repairable ceiling fan / exhaust fan of any size/sweep from existing position including taking down old connections wire complete all as directed and keep in safe custody for repairs and refixing the same on the same / different location with provision of new flexiable wire including cleaning of external surfaces & servicing the fan by dismantling complete greasing oiling and replacement of unserviceable parts as complete all as specified & directed (Note :- Any parts needed to be replaced for satisfactorily running of ceiling fan / exhaust fan shall be measured and paid separately under appropriate items).

Supply only capacitor of capacity 2.5 mfd 230 volt suitable for ceiling fan of any make / model and sweep .

Supply only Ball bearing No. 6201 suitable for ceiling fan of any sweep.

Supply only Ball bearing No. 6202/6203 suitable for ceiling fan of any sweep.

S & F heavy duty Exhaust fan 300mm sweep, 1400 RPM, metal body with metal blades, with bird screen incl connecting up with provision of cable 0.5 sqmm twin core PVC insulated from ceiling rose/connector to fan of including fixing the fan frame to wall opening with suitable size rag bolts after drilling, making hole to wall as per size and making good including louver and shutter complete all as specified and as directed. (Make - CG / Surya / Havells / Khaitan)

S&F in repairs 25 mm dia steel water tube medium grade galvanised with all fittings and fixed complete laid in trenches complete including necessary earth work all as specified and directed.

S&F in repairs 25 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed .

M&L for cutting / drilling the existing GI pipe 80/50 mm dia including CI/DI/GI tee, bend, tapper etc. All necessary items complete all as specified and as directed.

M&L cutting chases and making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps cills, sunshades, shelves, lintels etc. in brick walls and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc. 10 cm girth complete all as specified & directed. (Note:- Disturbed surfaces of wall shall be make good by applying two coats of OBD over a coat of wall care putty over cement mortar plaster (1:3) where necessary to match with existing surface finish).

M&L for painting to ceiling fan of any sweep complete with one coat of synthetic enamel paint by spraying including filling cavities with fillar with necessary preparation of surface including hanging the ceiling fan and connecting up complete all as directed.

AUTO ELECTRICALS

SUDHA ENTERPRISES

KWALITY CONSTRUCTION

DIPAK ENTERPRISE

CHOWDHURY SMALL INDUSTRIES

M/S SK PAUL

SOVA ENTERPRISE